Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹13.2 CrAccepted-Finance | ₹13.2 Cr | L1 | Accepted-Finance Accepted |
| 2 | Rejected-Technical | - | - | Rejected-Technical Technically not responsive |
| 3 | Rejected-Technical | - | - | Rejected-Technical Technically not responsive |
| 4 | Rejected-Technical | - | - | Rejected-Technical Technically not responsive |
| 5 | Rejected-Technical | - | - | Rejected-Technical Technically not responsive |
Tender Value
Refer Docs
EMD Value
₹25.2 L
Closing Date
11 Feb 2021, 10:30 amClosed
Executive Engineer
Office of the Executive Engineer, Roing Division, PWD, AP Roing-792110
Upgradation of District Hospital at Roing under RIDF-XXVI.
2021_PWDAP_401_1
RD/RNG-1/2020-21/02
Open Tender
Civil Works
1095 days
Roing
As per bid document
3 documents required · 3 mandatory
₹5,000
EE PWD Roing
₹25.2 L
Yes
Roing
18 Mar 2021
28 Jan 2021
11 Feb 2021
29 Jan 2021
11 Feb 2021
29 Jan 2021
9 Feb 2021
Amount
Civil works for building
SH:-Earthwork Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.
Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.
Filling in plinth with sand under floors including watering ramming, consolidating and dressing complete
SH:-Concrete works Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in: a) Foundation & plinth
SH:- RCC Work Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Design mix concrete) a) All works upto plinth level.
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :-Design mix concrete) a) All works above plinth level upto floor V level.
6 mm thick cement plaster 1:3 (1 cement:3 fine sand) @ 7.45 sqm per cum of concrete work.
Reinforcement of RCC work including bending, binding and placing in position complete. a) Tor/TMT steel
Centering and shuttering including strutting propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.
b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.
c) Column, pillars, posts and struts etc.
d) Lintels, beams, girders, bressumers and cantilevers etc.
e) Stairs
f) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).
SH:-:-Brick work Brick work with best available local bricks cement mortar 1:4 (1 cement : 4 fine sand).
Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.
Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.
Extra for half brick masonry in superstructure above plinth level and up to floor two level
SH:- UPVC Works Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections , of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.
Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. A) 35 mm thick
Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness .The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.
Providing and fixing to existing door frames. 1) 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames.
Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealant shall be paid separately) 1) Two track two panels sliding window made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)
2) Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).
Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)
SH:- Aluminium Works Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately) : For fixed portion. 1.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868,Minimum anodic coating of grade SC 15)
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of Aluminium snap beading shall be paid in basic item) : With float glass panes of 5.5 mm thickness
Filling the gap in between aluminium frame & adjacent RCC/ Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete upto 5 mm depth and 5 mm width.
Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).
Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete. a) 300 x 10 mm
Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete. a) 125 mm
Providing and fixing 100 mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.
SH:- Steel Work; Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete.
Providing and fixing stainless steel railing of 90 CM height i/c handrail of top & bottom etc. complete as per direction of Engineer-in-Charge
Providing & fixing of Glass canopy supported by walls / beam or by glass façade with articulated bolts & threaded rods which provide adjustment at site glass of 8mm thick.(Frame materials - aluminium)
SH:- Flooring Work : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and onforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. b) Size of Tile 1000 x 1000 mm
Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. a) Size of Tile 1000 x 1000 mm
White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.
Providing and laying Polished Granite stone flooring in required design and patterns in linear as well as curnilinear portions of the building all complete as per the archtectural drawings with 18mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbling curing and polishing etc. all complete as specified and as directed by the Engineer-in-charge. 11.56.1 Polished Granite stone slab jet black, Cherry red, elite brown, cat eye of equivalent.
Providing & fixing PVC Viniyle flooring i/c a base layer of thermocol sheet 5.00 mm thick complete as per direction of Engineer-in Charge.
Chequered terrazzo tiles 22 mm thick with marble chips of sizes upto 6mm in floors on 25 mm thick bed mortar 1 : 3.. a) Light shade using White cement
SH:- Roofing Work : Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses.
Providing and fixing Durashine zinc- luminium alloy coated (TATA Bluescope building product) sheet ridges fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses.
Providing & fixing of Polycarbonate roofing
Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light Code Description Unit Rate No. 429 SUB HEAD : 26.0 NEW TECHNOLOGIES AND MATERIALS reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. a) With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged GRG false ceiling tiles.
SH:- Finishing Work: 15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall.
Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.
Applying one coat of distemper primer of approved brand and manufacture on wall surface.
Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.
SH:- Miscellaneous Work: Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement :3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.
Public Health Engineering works
EXTERNAL DRAINAGE SYSTEM : Construction of cement concrete drain 15 cm wide and 15 cm deep, to be layed in 1: 400 slope , in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete
Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete.
Constructing brick masonry manhole & Catch Basin with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design. a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).
Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. a) 150 mm dia SW pipes
b) 200 mm dia SW pipes
Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. a) 150 mm dia SW pipes
b) 200 mm dia SW pipes
Sump Pump Delivery Line- UPVC SWR Type B and 80 mm dia pipe along with fittings and supports complete
Construction of Brick Masonery chamber and Oil and Grease Trap as specified in Drawing ( 600 X 600 mm)
WATER SUPPLY SYSTEM : Providing and fixing on wall face C.I. rain water pipe including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 ( 1 cement : 2 fine sand). a) 150 mm diameter pipe
Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work) for Hot and Cold water supply system a) 15 mm nominal bore
b) 20 mm nominal bore
c) 25 mm nominal bore
d) 32 mm nominal bore
Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work). a) 20 mm nominal bore
b) 25 mm nominal bore
c) 32 mm nominal bore
e) 40 mm nominal bore
f) 65 mm nominal bore
g) 80 mm nominal bore
Providing & fixing 9 mm thick thermal insulation elastomeric flexible material having hermetic blistered closed cell structure of expanded synthetic rubber over pipes/ fitting as per manufacturer's specifications etc.complete.
Providing and fixing PVC connection pipe with brass union. A) 45 cm length a) 15 mm nominal bore
Providing and fixing brass bib cock of approved quality. a)15 mm nominal bore
Providing and fixing brass stop cock of approved quality. a) 15 mm nominal bore
Providing and fixing Gun metal Gate valve with CI wheel of approved quality ( Screwed end) a) 20 mm nominal bore
b) 50 mm nominal bore
c) 65 mm nominal bore
Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet. a) 100 mm dia
Providing and fixing CP brass (for shower)hot and cold mixer for shower, single lever , exposed , with necessary joints, wall flange etc comple
Providing and filling sand all round GI pipes in external work. a) 25 mm dia pipe
b) 40 mm dia pipe
Providing and fixing ball valve (brass) of approved quality complete. a) 20 mm dia pipe
b) 25 mm dia pipe
c) 32 mm dia pipe
d) 40 mm dia pipe
Providing and fixing Brass Automatic Air release valve screw type of approved quality complete. a) 20 mm dia pipe
Providing and fixing Butterfly Valve PN 1.0 (with SG Iron Disk & Slim seal standard lever operated type, Nitrile/EPDM rubber linning and flange ) of approved quality complete. a) 65 mm dia pipe
b) 80 mm dia pipe
Providing and fixing non-return valve of approved quality a) 40 mm dia pipe
Providing and fixing of Y-Strainer, Flanged type, PN 1.0 with SS mesh and suitable flange of approved quality a) 65 mm dia pipe
b) 80 mm dia pipe
Providing and Fixing of Floor mounted Drinking water dispenser of approved make and quality
Providing and Fixing of tripple layer POLYTHENE water tank of 10 KL capacity approved make and quality. With cover and locking arranngement
INTERNAL DRAINAGE AND SANITARY INSTALLATION : Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer
Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleats with CP brass screws and washers.
Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleats with CP brass screws (heavy quality). a) 750 x 20 mm size
Providing and fixing kitchen sink including making all connection excluding cost of fittings. a) White glazed fire clay sink size 600x450x150 mm
Providing and fixing kitchen Lab Sink including making all connection excluding cost of fittings.
Providing and fixing UPVC SWR Type B ( As per IS 13592) soil, waste and vent pipes along with all necessary fittings and supports a) 75 mm dia NB
b) 100 mm dia NB
Providing and fixing sand UPVC SWR Type B basin waste pipes as per IS 13592 along with all necessary fittings and supports a) 40 mm dia
Providing and fixing of P trap of following sizes with SS gratings with a minimum water seal of 50 mm , complete with inbuilt cockroach trap a) 100 mm inlet & 75 mm outlet
b) 125 mm inlet &100 mm outlet
Providing and fixing of Clean out Plug with suitable insert key for PVC pipe with a threaded socket as necessary a) 100 mm dia
b) 75 mm dia
Providing and fixing of rainwater collection Khurrah with leaf trap , grating made out of UPVC with flange a) 150 mm dia
Providing and fixing white vitreous china pedestal type (European type WC pan) water closet with seat and lid with CP brass hinges and rubber buffers, 12.5 Litres white vitreous china low-level flushing cistern with fittings and brackets 40 mm white porcelain in enamel led flush band, 20 mm over flow pipe with specials and mosquito proof coupling of approved municipal design complete including cutting and making good the walls and floors where required. a) WC pan with white plastic seat and lid, Flush Tank
Providing and fixing white vitreous china flat back type lipped front urinal basin of 430x260x350 mm and 340x430x265 mm sizes respectively with CI automatic flushing cistern with fittings, RS or CI brackets standard size galvanized steel flush pipe and spreaders with brass unions and GI clamps complete including painting of cistern and fittings, cutting and making good the walls and floors where required. a) One urinal basin with 5 Litres CI automatic flushing cistern
a) Providing and fixing of CP Brass waste for wash basin and sink. i) 40 mm dia
b) Providing and fixing MI fisher union for wash basin and sinks. i) 40 mm dia
c) Providing and fixing CP brass or MI trap for wash basin and sinks. i) 40 mm dia
Providing and fixing of health faucet for EWC approved make with necessary CP flex hose 1000 mm long and nozzle with supports and complete
Providing and fixing ss scrub sink 2 -Bay size manufactured from 1 mm thick SS 304 18G grade nickel steel with top quality polish , 1 no 40mm dia Cp waste coupling with flexible hose pipe connection upto floor trap , elbow operated sink mixer with swing spout table mounted type and necessary wall flange etc complete
Providing and fixing toilet paper holder of CP Brass
Providing and fixing soap dish holder CP Brass
AIR TO WATER HEAT PUMPS FOR GENERATING HOT WATER : Supply, Erection, Testing & Commissioning of Micro Processor Controlled Modular Air to Water Scroll Heat pump delivering actual capacity as per the following parameters duly installed at site(modules shall operate in master slave combination with automatic run time equalization between the modules. ) The Heat Pump should be complete with Single/multiple hermatic scroll compressors , Condensors, Heat Exchangers, Electronic Expansion Valve,Primary circulation pump, braze plate type (SS316) primary heat exchanger, anitvibration rubber mounts with factory assembled with Electrical panel mounted on the heat pump including the disconnect switch suitable for 50 Hz, 3 Phase, 415 volts, AC supply. The vibration isolators shall be shipped alongwith heat pump from your works. Heat Pump should be capable of generating Hot Water upto 55ºC. Suitable Nos. & suitable capacity starter in IP 55 protection First charge of R410 A refrigerant and oil duly charged at factory Outdoor ambient air temperature 9.5°C DB / 9°C WB, Minimum COP 4.39 at above conditions Heating capacity = Actual at below mentioned conditions Cold Water Inlet Temp = 10 Deg C Hot Water Outlet Temp = 60 Deg C Air Ambient Temp = 25 Deg C Avg Minimum Hot water genration = 3500 Liter/Day Assumed peak usage hours/ day = 4 hours Refrigerant : R-410A System Should be Capable to Operate at Air Ambient Temp from 5 to 45 Deg C The heat pump as described above shall be inline with specifications. Along with Primary Pump Heating capacity = 10 KW , Flowrate = 1500 LPH Nominal, Connection size DN 32 Minimum COP = 4.1 1 working and 1 standby Vendor to submit complete inter unit design, Capacity calculations and COP certificates and shop drawings with schematics to consultant for approval before procuring any material or equipment at site. Pumps to be installed in parallel in such a way that during peak demand , both can be used simulteneously and otherwise only 1 can be switched off.
Mandatory Inclusions within quoted price: 1 No. - Matching Air Cooled condenser with copper tubes and aluminium fins 1 No. - Matching Water Side heat exchanger of Shell and Tube / BPHE/ Co Axial Tube in Tube type as per manufacturer's design 1 Lot - Refrigerant piping fittings, valves, accessories to inter connect compressor, condenser, chiller and expansion valve. 1 Set - Control panel with display comprising of Controls. It shall also be equipped with protection and monitoring devices such as H/L Pressure switch/ Thermal and Current Overload Protector 1 Lot - DP/ Flow switches at inlet and outlet water drain & air purge valves, wherever required. Lot- suction line and required insulation Lot-frame work for mounting the above with base plate complete with antivibration pads/ springs. Lot- Initial/ first charge of refrigerant gas & compressor oil duly charged at factory. Lot- RCC/ cement concrete foundation for equipment Lot- Pressure Gauge, Temparature Gauge and Air release valves as required Lot -Primary Pumps , Valves, Strainers , De scaling System , Other necessary pumps etc Supply of MS/SS Hot water mixing tank with Glasswool Insulation, Working pressure 4 bar/Testing Pressure 6 bar, Moc - MS. HOT WATER MIXING TANK, CAP:1000 L (1W), Fitted with Air / steam release valve and drain valve
Associated electrical Panels and Accessories including cabling, MCB & RCCBs as required , glands, Supports, Earthings, Terminations etc
PUMPS AND ASSOCIATED ITEMS-WATER SUPPLY AND SEWARAGE LIFTING PUMPS FROM TWT TO OHT Procurement, supply, erection & commissioning of electrically operated clear water multistage vertical lifting pumpsets (IE3 Rating & Suitable for aluminium cabling) self priming type complete with mechanical seals,protection sensors overload/undervoltage tripping/ {oil leakage if required)/ electronic (magnetic) level sensing unit & dry run cut off. The pumps should be with C.I. housing, bronze or S.S. impeller,to be housed in Pump room with minimum one size higher port valves for discharge & suction lines.The pump discharge pipe is to be provided with glycerine filled diaphragm pressure gauge with shatterproof glass & bleed valve . All accessories viz. expansion bellow, pressure gauge, switch, pet cock & all other materials for fixing should be included in the offer. Electrical control panel should be included in the offer as separate item given below. Head : 45 M , Flowrate : 22 GPM Delivery Port : 40 mm Dia , Minimum Motor Power : 0.75 KW
Flushing water supply Head : 41 M , Flowrate : 44 GPM Delivery Port : 40 mm Dia , Minimum Motor Power : 1.4 KW Treated water Supply
SUBMERSIBLE WASTE WATER TRANSFER PUMP Procurement, supply, erection & commissioning of electrically operated submersible wastewater transfer pump (IE3 Rating & Suitable for aluminium cabling) complete with mechanical seals,protection sensors overload/undervoltage tripping/ {oil leakage if required)/ electronic (magnetic) level sensing unit & dry run cut off. The pumps should be with bronze or S.S. impeller,to be housed inside sumps as indicated in drawing.Minimum Partcle size upto 50 mm and head 20 M. All accessories for fixing along with delivery hose should be included in the offer. Electrical control panel should be included in the offer. Head : 20 M Flowrate : 15 Cum/Hr, Delivery pipe size 80 mm 1 working and 1 standby
TERRACE BOOSTER PUMP WITH PRESSURE VESSEL : Procurement, supply, erection & commissioning of electrically operated Inline water Pressure booster pump ( (IE3 Rating & Suitable for aluminium cabling)) suitable to be integrated with Pressure Vessel and Hydraulic Pressure drop sensor, complete with Pressure vessel ( Pressure Vessel Type: Single Diaphram type, with SS water Connection and PP liner and including complete with mechanical seals, Air Valves, level sensing unit etc. and size as per manufacturer specification). Pump shall be provided with seals,protection sensors overload/undervoltage tripping/ {oil leakage if required)/ electronic (magnetic) level sensing unit & dry run cut off. The pump discharge pipe is to be provided with glycerine filled diaphragm pressure gauge with shatterproof glass & bleed valve . Electrical control panel should be included in the offer as integrated item . Flowrate : 65 GPM or 15 Cum/Hr , Head : 36 M , 2. 4 KW For DWS
Flowrate : 45 GPM or 10 Cum/Hr , Head : 36 M , 1.7 KW For FWS
Pressure Vessel Capacity : Minimum 50 L , Vertical Type,10 BAR
HOT WATER RECIRCULATION PUMP Procurement, supply, erection & commissioning of electrically operated inline hot water recirculation pumpset (IE3 Rating & Suitable for aluminium cabling), self priming type complete with mechanical seals,protection sensors overload/undervoltage tripping/ {oil leakage if required)/ electronic (magnetic) level sensing unit & dry run cut off. The pumps should be with C.I. housing, bronze or S.S. impeller,to be housed in attic floor with same size port valves for discharge & suction lines. All accessories viz. expansion bellow, pressure gauge, switch, pet cock & all other materials for fixing should be included in the offer. Electrical control panel should be included in the offer as separate item given below. Head : 45 M Flowrate : 20 LPM , Port Size 25 mm 1 working and 1 standby
SUBMERSIBLE IRRIGATION PUMP: Multi-stage submersible pump of capacity 10 GPM, having 2 hrs duty with 32 mm delivery port , Delivery Head 50 M , rated capacity 0.50 KW against given flowrate all necessary Housings, Casings, Panels, valves, strainers, fittings, tees, elbows. Lifting Chain block and accessories. (IE3 Rating & Suitable for aluminium cabling)
DOMESTIC WATER TREATMENT PLANT : Supplying, installation, testing & commissioning of Water Treatment Plant ( capable to deliver 4 cum/ hr water at desired quality ( less than 350 PPM) as per codesof practice ) . PLANT BREAK UP AS FOLLOWS IRON REMOVAL FILTER ( REQUIREMENT TO BE VALIDATED BASED ON LATEST BASED ON WATER TEST REPORT ) IRON REMOVAL FILTER Supply Erection , testing, Commissioning of approved make Iron Removal Filter filter of FRP make with Epoxy Coated with necessary equipment complete with Frontal piping, valves, suitable supports for mounting, pressure guage, orifice plate etc..,complete as per the detailed specification for the efficient working of system. Pressure Vessel to be designed as per IS 2825 unfired preesure vessel with necessary corrossion allowance along with necessary pumps, fittings, pipes, valves, Supports and accessories Flow: 5 M3/Hr and upto 30 M3/day Max Working Pressure:3.5Kg/cm2 Min Working Pressure:2Kg/cm2 Type of Flow : Down Flow Back Wash :once in a day
ACTIVATED CARBON FILTER : Supply Erection , testing, Commissioning of approved make ACF of FRP construction with necessary equipment complete with Frontal piping, valves, suitable supports for mounting, pressure guage, orifice plate etc..,complete . Pressure Vessel to be designed as per IS 2825 unfired preesure vessel with necessary corrossion allowance. To be supplied along with necessary pumps, fittings, pipes, valves, Supports and accessories . Filter Diameter : Min 600 mm. Height: 1800mm, . Filter media: Activated charcoal ( carbon) Min Flow: 5 M3/hr and up to 30 M3/Day with 6 Hrs Operation , Min Working Pressure:3.5 Kg/cm2. Back Wash : once in a day
MULTI GRADE FILTERS : Supply Erection , testing, Commissioning of approved make ACF of FRP construction necessary equipment complete with Frontal piping, valves, suitable supports for mounting, pressure guage, orifice plate etc..,complete. Pressure Vessel to be designed as per IS 2825 unfired preesure vessel with necessary corrossion allowance. To be supplied along with necessary pumps, fittings, pipes, valves, Supports and accessories. Min Filter Diameter : 800 mm. Height: 1800mm, Shell thick ness : 6 mm, Disk thick ness- 8 mm. Filter media: Filtering sand, gravels and pebbles . Min Flow: 5 M3/hr and up to 30 M3/Day with 6 Hrs Operation Min Working Pressure:3.5 Kg/cm2. Type of Flow : As per Supplier Spec Back Wash : once in a day Filter Make: Tata/Pentair PUMPS , VALVES AND ACCESSORIES
Supplying , testing, Commissioning of All necessary Pumps, Valves and Accessories along with mechanical seals,protection sensors overload/undervoltage tripping/ {oil leakage if required)/ electronic (magnetic) with dry run cut off. The pumps should be with bronze or S.S. impeller,to be housed inside designated WTP area Make : Xylem/Kirloskar / Approved Equivalent Flowrate and Head as per Manufacturer Specifications Filter Make: Tata/Pentair
CHLORINATOR : Supplying of chlorine dosing system consisting of one HDPE tank of 50 litres capacity with a positive displacement diaphragm dosing pump having variable flowrate. The motor shall be suitable for operation at 240 V/Single phase/50 Hz. Supply. Make : E-Dose / Approved Equivalent
FEED PUMP : Supplying, installing, testing and commissioning vertical online/horizontal centrifugal pumping set with mechanical seal, C.I. Housing, C.I. volute and SS impeller & SS shaft connected to a TEFC induction motor of suitable HP for 415 volts, 3 phase, 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads, base plate wiring upto panel and equipment for water level controller to start and stop the pump automatically at predecided levels of the water in the tank with provision of protection for dry run etc. complete in all respect with provision of protection for dry run etc. complete in all respect (The shop drawing or the pumps along with its characteristics curves, model and technical data etc. are to be submitted for approval before purchase of pump). WTP Filter feed pump(1 W+ 1 SB) Head 20 M, Capacity : 120 LPM ( Kirloskar/Wilo)
Electrical Panel and accessories Vendor to submit complete design P&ID,Plan & Section , Calculations in PDF form and output water quality to consultant for approval
RO PLANT PRIMARY RO PLANT Supply ,Testing and Commissioning of R.O. Plant capable to deliver Output water at TDS < 150 PPM and along with necessary dozing system to set the TDS value as per requirement (Output water TDS adjustable atleast upto 70 PPM) . Plant should be POWDER coated M.S. skid complete with i) Required Numbers and grade of membrane (vendor to design and get approval from consultant) ii) 2 element housing. iii) SS 316 Impeller - High Pressure Pump. iv) Control Panel v) Pr. Gauge, Flow meter, TDS meter & All other Equipments The Rate Should Include Complete items inclusive of Necessary 3KL PVC Storage Tanks, Valves, Pipings, Pumps, Strainers, Supports and Other accessories . Rate to include piping cost to blend reject from secondary RO back to TWT ( Suction Tank). Backwash once a day. Vendor to consider pre filter reqirement , if any, based on water test at their own cost. Vendor to submit design details, p&ID and plan /section drawings along with membrane calculations for approval. Vendor to submit technical datasheet including membrane details.
SECONDARY RO PLANT Supply ,Testing and Commissioning of 500 LPH R.O. Plant capable to deliver Output water at TDS < 5 PPM and along with necessary dozing system to set the TDS value as per requirement (Output water TDS adjustable atleast upto 2 PPM) . Plant should be epoxy coated M.S. skid complete with i) Required Numbers and grade of membrane (vendor to design and get approval from consultant) ii) 1 no.1 element housing. iii) SS 316 High Pressure Pump. iv) Control Panel v) Pr. Gauge, Flow meter, TDS meter. The Rate Should Include Complete items inclusive of Necessary 1 KL PVC Storage Tanks, Valves, Pipings, Pumps, Strainers, Supports and Other accessories . Backwash once a day
STORM WATER DRAIN FROM CAMPUS TO MAJOR DRAIN: Construction of cement concrete storm water drain 70 cm wide at top, 55 cm wide at bottom and 65 cm deep in cement concrete 1 : 2 : 4 (1 cement : 2 sand : 4 stone aggregate 20 mm nominal size) and plastering on all exposed surfaces with 15 mm thick cement mortar 1 : 3 (1 cement : 3 fine sand) including shuttering complete.
Fire services works
Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 56 m head
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 250 mm dia
200 mm dia
150 mm dia
100 mm dia
80 mm dia
40 mm dia
25 mm dia
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm
Supplying, Installing, testing and commissioning wafer type butterfly valves in CI body with integrally moulded liner of Nitrile or EPDM, lever operated with required flanges, nuts, bolts etc. complete. (Test Pressure - PN 10) 150 mm
Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. a) 150 mm
Supplying, installing, testing and commissioning Cast Iron Gate valves conforming to IS 14846 (PN 1.6), Non rising stem with hand wheel operation, SS stem, EPDM coated CI wedge 100% vacuum tight design with toroidal sealing rings and over 250 micron epoxy coating a) 200 mm
Supplying, installing, testing and commissioning of brass forged body ball valves screwed with teflon seals, stainless steel ball & stem, with all suitable nuts, bolts, etc complete a) 40 mm dia
Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
Supplying, installing, testing and commissioning of Pressure gauges of 0-16 kg/sqcm for pump sets and pipe lines for the respective floors near to the flow switches with Ball valves, siphon, Fittings like unions / colors / reducers etc. Glycerin filled pressure gauges to use on pump discharge lines.
HYDRANT SYSTEM : Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : a) 100 mm dia
Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. (External Yard Hydrant and underground pipe) a) 150 mm dia
b) 80 mm dia
Supplying, Installing, testing and commissioning wafer type butterfly valves in CI body with integrally moulded liner of Nitrile or EPDM, lever operated with required flanges, nuts, bolts etc. complete. (Test Pressure - PN 10) a) 100 mm
Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 3-way - 150 mm dia MS pipe
External Hydrant System : Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single Headed Gun metal
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. a) 40 m
Steel buckets with hanging clamp filled with sand
Internal Hydrant system : Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single Headed Gun metal
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. a) 40 m
Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required
Steel buckets with hanging clamp filled with sand
25mm Air release valve as per IS:14845 ISI Marked
AUTOMATIC SPRINKLER SYSTEM : Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia
100 mm dia
80 mm dia
65 mm dia
50 mm dia
40 mm dia
32 mm dia
25 mm dia
Supplying, installing, testing and commissioning of brass forged body ball valves screwed with teflon seals, stainless steel ball & stem, with all suitable nuts, bolts, etc complete
Supplying, Installing, testing and commissioning wafer type butterfly valves in CI body with integrally moulded liner of Nitrile or EPDM, lever operated with required flanges, nuts, bolts etc. complete. (Test Pressure - PN 10) 150 mm
Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent
Upright
Horizontal Sidewall Sprinkler
Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 141 degree centigrade with required accessories : Pendent
Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 150 mm dia
Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required: 1500 mm
Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 150 mm dia
Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.
25mm Air release valve as per IS:14845 ISI Marked
ADDITIONAL REQUIREMENTS FOR FIRE FIGHTING SYSTEMS NOT COVERED UNDER ESTIMATED COST BUT REQUIRED AS PER NBC FIRE EXTINGUISHERS Carbon-di-oxide Gas Type Fire Extinguisher 4.5 Kgs, squeeze Grip, Discharge Time less than 10 Secs, Controllable discharge mechanism with nozzle, bend, Hose and wall mounting bracket etc., Applicable on Class B&C Fire, B Rating 21B, Can Construction : Hot Spinning / Forging, Valve Construction : Forging & Machining, Internal Coating of Can : Seamless Cylinder, External Coating of Can : Spray Painting, Sheet metal thickness : 4.5MM, ISI Approved as per IS:2878:2004
ABC Powder 6 Kg Fire Extinguisher containing Mono Ammonium Phosphate Powder 50, Stored Pressure Type, Pressure Gauge, fitted with discharge hose, wall mounting bracket etc., Discharge Time less than 15 Secs, Controllable discharge mechanism, Range minimum 4 Meters, applicable on Class A,B,C and electrically started Fire, A Rating- 8A, B Rating 34B, Can Construction : Deep drawn & Co2 Mig welded, Valve Construction : Forging & Machining, Internal Coating of Can : Epoxy Powder coating, External Coating of Can : Epoxy Polyester Powder coating, Sheet metal thickness : 1.60MM, ISI approved as per IS:15683:2006
45 (Ltr) Mechanical Foam Wheeled Fire Extinguisher (AFFF) Based, Operating Temperature Range (+) 5 to (+) 55 oC
AFFF Foam Type fire extinguisher 9 Lt Capacity, Stored Pressure Type, Pressure Gauge, Discharge Time less than 60 Secs, with hose and brackets, Controllable discharge mechanism, Range minimum 6 Meters, applicable on Class A,B, A Rating 13A, B Rating 55B, Can Construction : Deep drawn & CO2 Mig welded, Valve Construction : Forging & Machining, Internal Coating of Can : Epoxy Powder coating, External Coating of Can : Epoxy Polyester Powder coating, Sheet metal thickness : 2.0MM, ISI Approved as per IS 15683:2006
SIGNAGES Supplying and installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC reflective self adhesive vinyl painted foam board, complete with mirror fasteners. Signage with printed "IN CASE OF FIRE, USE STAIRS UNLESS INSTRUCTED OTHERWISE" of 1.5cm height letters in red with white back ground. The size of the board shall be 25cm x 30 cm and shall be fixed at the height of 2 mts. from finished floor near Manual call points.
Floor identification signage ( i.e., GROUND FLOOR …etc.) at each stair enclosure on every floor, indicating the floor number in words, lettering size shall be 7.5 cm with contrasting color from back ground. Size shall be 15cm x 60cm.
Fire Exit signage- Double sided: 150 x 400 Providing and fixing "Fire Exit" letters signage (with or without directional arrows as per signage plan, ref. by architect). Signage to be made of 3 mm thick foam board with edge to edhe self-adhesive, self luminiscent Forex or equivalent inyl stuck on it. Fix green vinyly to cover Forex vinyl leaving 6 mm border around edges with Exit letters cut-out. The exit letters shall be 150 mm height. Double side false ceiling suspended with chain look and hook. Unidirectional, printed both sides with sinle arrow or double arrow.
Supplying and installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC reflective self adhesive vinyle painted foam board, complete with mirror fasteners. Fire hose reel
Lifts
Fire extinguishers
Analogue addressable Main fire alarm panel
Sprinkler control valves
Manual Call Points
Staircase Arrow Sign - Imported Acrylic Sheet 4mm, grade 1 autoluminscent film, preplotted media with extra over laminate at the back. Size: 6’’ x 4’’
Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.
Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.
Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.
Supplying, installation, testing & commissioning of fault isolator complete with base as required.
Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.
Supplying, installation, testing & commissioning of addressable manual call point complete as required.
Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.
Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.
UNDER GROUND RESERVOIR (UGR)
EARTH WORKS : Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.
Extra for every additional lift of 1.50 m or part thereof for earth work in all soils including shingles, small size boulders upto 30 cm size but excluding saturated soil and rock.
CONCRETE WORK : Providing & laying cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 stone aggregate 40mm nominal size) excluding cost of centering & shuttering. a) Foundations and plinth
RCC WORK Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specifications a) RCC Grade M25 Using concrete Mixer
Reinforcement of RCC work including bending, binding and placing in position complete. a) Tar/TMT steel
Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.
b) Lintels, beams, girders, bressumers and cantilevers etc.
c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).
c) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.
d) Stairs (excluding landings) except spiral stair cases.
e) Column, pillars, posts and struts etc.
BRICK WORK : Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).
FLOORING WORK Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. a) 50 mm thick
STEEL WORK : Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
UPVC DOOR : Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm). Float glass panes
5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).
FINISHING : 12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).
15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall.
6 mm cement plaster to ceiling 1 : 3 (1 cement : 3 fine sand).
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.
Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.
Medical Gas Pipe line System works :
OXYGEN SYSTEM 10 + 10 size manifold complete with middle frame with chain for individual cylinder along with Non Return Valve for every cylinder as per specification (Recommended Make-Aktiv)
Semi Automatic Control Panel for Oxygen having constant flow output of over 1000 LPM or more at 4.2 Bar Pressure as per specification (Recommended Make-Aktiv)
4 Cylinder Emergency manifold complete with middle frame with chain for individual cylinder along with Non Return Valve for every cylinder along with high flow Pressure Regulator as per specification (Recommended Make-Aktiv)
Front Loading Oxygen Outlets (BS-Type) with Probe as per specification (Recommended Make-Aktiv)
Oxygen Flowmeter with Humidifier as per specification Range: 0 to 15 LPM (Recommended Make-Aktiv)
Range: 0 to 5 LPM (Recommended Make-Aktiv)
Oxygen Kit Conversion (Recommended Make-Local)
NITROUS OXIDE SYSTEM : 2 + 2 size manifold complete with middle frame with chain for individual cylinder along with Non Return Valve for every cylinder as per specification (Recommended Make-Aktiv)
Semi Automatic Control Panel for Nitrous Oxide having constant flow output of over 300 LPM at 4.2 Bar Pressure as per specification (Recommended Make-Aktiv)
Two Cylinder Emergency Nitrous Oxide arrangement using a high flow Preset Pressure Regulator as per specification (Recommended Make-Aktiv)
Front Loading N2O Outlets (BS-Type) with Probe as per specification
N2O Kit Conversion (Recommended Make-Local)
MEDICAL VACUUM SYSTEM : Central Vacuum System Complete with 2 nos. Vacuum Pump each havig 60 cfm PD with 5 Hp motor, Filter, Interconnecting Piping, NRV, Auto Switch Gear Assembly, Exhaust Silencer and 1 no. 1000 Litre Vacuum Tank. Refer specification for details (Recommended Make-Vacuum Pump-Ingersoll Rand)
Front Loading Vacuum Outlets (BS-Type) with Probe as per specification (Recommended Make-Aktiv)
Ward Vacuum Unit with Regulator, Collection Jar of 600 ml with Bracket as per specification (Recommended Make-HMP)
Theatre Vacuum Unit mounted on Trolley consisting of Vacuum Regulator with Gauge and 2 nos. of 2000 ml Polycarbonate Jar as per specification (Recommended Make-HMP)
MISCELLANEOUS ITEMS : Distribution Copper Pipe as per EN 13348 - Lloyds Certified as per specification (Recommended Make-Mexflow manufactured by Mehta Tubes) 42 mm OD x 1.2 mm thick
28 mm OD x 0.9 mm thick
22 mm OD x 0.9 mm thick
15 mm OD x 0.9 mm thick
12 mm OD x 0.7 mm thick
Medical Gas Digital Area Alarm System as per specification (Recommended Make-Aktiv) 3 - Gas
Area Valve Box with Valve & Gauge (Recommended Make-Aktiv) 3 - Gas
Floor Isolation Valve with End Fittings as per specification (Recommended Make-RB/RV/Matrix) 15 mm
MGPS & BIO-MEDICAL WASTE ROOM EARTH WORKS : Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.
Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.
Filling in plinth with sand under floors including watering ramming, consolidating and dressing complete
CONCRETE WORK : Providing & laying cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 stone aggregate 40mm nominal size) excluding cost of centering & shuttering. a) Foundations and plinth
RCC WORK : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Disign mix concrete.) a) All works upto plinth level.
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :-Design mix concrete) b) All works above plinth level upto floor V level.
6 mm thick cement plaster 1:3 (1 cement:3 fine sand) @ 7.45 sqm per cum of concrete work.
Reinforcement of RCC work including bending, binding and placing in position complete. a) Tar / TMT Bar
Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.
c) Column, pillars, posts and struts etc.
d) Lintels, beams, girders, bressumers and cantilevers etc.
BRICK WORK : Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).
Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.
FLOORING WORK : Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. a) 50 mm thick
STEEL WORK : Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).
ALUMINIUM WORK Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete. a) 300 x 10 mm
Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete. a) 125 mm
Providing and fixing 100 mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.
UPVC DOOR : Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm). Float glass panes
5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).
ROOFING : Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses.
Details of cost for 179.655 Sq.m.Laying and fixing 20 sheets in 3 row require Overall Sheet area of 20 x 3 x 3.05 x 1.072 plus 3% wastages = 202.061 Sqm After H & L laping as per manufacturer's specification, effective Area Measurable will be 20 x 3x 2.95 x 1.015 = 179.655 Sqm Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet ridges fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses.
FINISHING 12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).
15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall.
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.
Applying one coat of distemper primer of approved brand and manufacture on wall surface.
Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.
Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.
MISCELLANIOUS : Making plinth protection with 2nd class bricks on edge in cement mortar 1 : 6 (1 cement : 6 fine sand) over 7.50 cm bed of dry bricks aggregate 40 mm nominal size rammed consolidated and grouted with fine sand and the top of bricks pointed with cement mortar 1 : 2 (1 cement : 2 fine sand).
HVAC works :
Air conditioner split units : Hydrofolic Golden Fins (Evaporator) It is imperative to maintain the condenser and evaporator coils and ensure that they do not rust or corrode. Stabilizer Free Operation this feature ensures that the AC can withstand voltage fluctuations. Even in low or uneven voltage conditions, the cooling and performance of AC should not be affected. Self Clean Self Cleaning function removes the moisture from the indoor unit which causes mould to form. R32 GreenGas As well as having a lower global warming potential, R32's other benefits include: It has a lower toxicity, which is good for both human health and the wider environment. It has a high energy efficiency, so will not increase your energy bills. Inverter Air Conditioner Consumes less power in comparison to a traditional AC.,. No voltage fluctuation.,. Effective cooling.,. Keeps constant room temperature. General Information Split AC- StyleCompact Air Conditioner- TypeSplit ISEER/Star Value- 5 Condenser Coil- Copper Tonnage- 1.5 Ton 1.5 TR Hi-Wall Split Unit
INLINE FAN FOR EXHAUST AIR : Supply,installation,testing and commissioning of circular / rectengular type Inline type fans complete with motor, blower, mounting arrangement, power and control wiring etc. of below capacity. The Inline fan shall be suitable for 230V, 1Ph., 50Hz AC power supply. The static pressure will be calcualted by HVAC contrctor on basis of final duct layout. 150 CFM, 10 mm wc SP for Exhaust Air
650 CFM, 15 mm wc SP for Exhaust Air
800 CFM, 15 mm wc SP for Exhaust Air
PROPELLER FAN : Supply, installtion,Testing and commissioning of Propeller fan wiith motor complete in all respect & of following capacities. The casing of propeller fans Shall be PVC / METALIC and should be lower noise level. The fan shall be suitable for 230V, 1Ph., 50Hz AC power supply, 150 CFM
AXIAL FLOW FAN : Supply, installtion,Testing and commissioning of exhaust unit wiith motor complete in all respect & of following capacities. The casing of fans Shall be PVC / METALIC and should be lower noise level. The fan shall be suitable for 230V, 1Ph., 50Hz AC power supply, 600 CFM
DRAIN PIPING: Supply,installation,testing and commissioning of CPVC drain pipes density 20Kg/m3 complete with fittigs like elbows, tees, reducers, bends, flanges, supports with 9 mm thick class - O nitrile rubber insulatiions complete with supports as per drawings and specifications of below sizes. 32 mm dia.
25 mm dia
GI DUCT : Supply, Febrication & Fixing of 120 GSM GS sheet metal rectangular ducting as per IS 655/SMACNA complete with turning vanes, companion flanges, support, sealing of all seams with a suitable metal sealant as per drawings. 20 G
Refrigerant Pipe : Supply, installation, testing and commissioning of interconnecting high pressure copper refrigerant piping work suitable for refrigerant R410A/R32 duly insulated with class-O, GC cloth pasted elastomeric nitrile rubber type tubular insulation of density 40 ~60kg/m3 between indoor & out door units. External refrigerant piping shall be laid on 16G GI covered perforated cable trays, it shall include the cost of all the fitting, insulation and all required fittings, joints etc. as per drawings of the following sizes. Piping inside occupied area and vertical shaft shall de supported using GI Hangers. The 19mm thick insulation shall be considered for 19.1mm and above dia copper pipe and 13mm thick from 15.9mm dia and below size. All exposed pipe shall have weather proof quoting on GC Cloth and cost to be included in the piping rate and cable tray is quantified separately. Price of Cable Tray will be charged in item of cable tray in electrical part. External piping should be covred with the GI sheet on cable tray for weather protection. 12.7mm dia (0.80mm thick.)
6.4mm dia (0.80mm thick.)
Low Voltage System works
Network System.: Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable
Supply, Installation, Testing & Commissioning of internet socket RJ45 on recessed metal box and cover plate (inclusive) including all accessories as required like connection etc at site.
Supply, Installation, Testing & Commissioning of TV Coaxial socket with metal box on recessed including all required like connection etc at site.
Supply, Installation, Testing & Commissioning of CAT6 patch cord factory crimp cable for connecting RJ 45 including all required like connection etc at site. 1 metre
2 metre
Supply, Installation, Testing & Commissioning of Data Switch 24 port 10/100/1000 mbps, etc as required for site
Supply, Installation, Testing & Commissioning of Data Switch 16 port 10/100/1000 mbps, etc as required for site
Supply, Installation, Testing & Commissioning of CAT6 UTP 24 port Patch Panel complete with all accessories complete.
Supply, Installation, Testing & Commissioning of CAT6 UTP 16 port Patch Panel complete with all accessories .
CCTV System: Supplying, installation, testing and commissioning of 32 channels CCTV NVR 2 SATAPORT Network Video Recorder with all accessories such as internet connection, 2x4tb Hard Disk etc. complete in all respect to use at site.
Supplying, installation, testing and commissioning of 16 channels CCTV NVR 2 SATAPORT Network Video Recorder with all accessories such as internet connection, 2x4tb Hard Disk etc. complete in all respect to use at site.
Supplying, installation, testing and commissioning of 2MP full HD 1080p dome IP CCTV camera with all accessories complete in all respect to use at site.
Supplying, installation, testing and commissioning of 2MP full HD 1080p bullet IP CCTV camera IP-66 with all accessories complete in all respect to use at site.
Supplying, installation, testing and commissioning of 24 port rack mountable POE switch complete with all accessories .
Supplying, installation, testing and commissioning of 16 port rack mountable POE switch complete with all accessories .
Supplying, installation, testing and commissioning of 32 inch LED Monitor with VGA and HDMI Ports complete with all accessories .
Supply, installation, testing and commissioning of Closed Network rack with Front Glass Door and Perforated double door on the back, vertical power strips of surge protection sockets, with Front and Rear Equipment mounting angle, Side panels shall be secured with sliding latches operated from inside the rack, Cable Entry at the rear top and bottom. Top Cooling Fans min 2 Nos. Earthing kit, front door lock Bolts nuts and all accessories. For Server Room 21 U Rack
15U Rack
4 U Rack
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm
Public address system : Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.
Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.
Supplying, installing, testing and commissioning of Hand held Microphone including accessories as required
Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm
Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 mm
Nurse call system : Supply, Installation, Testing & Commissioning of call Station Board with Membrane push switches for call and Re-set buttons, & LEDs for Ready, Call and Wait, Connector for console connection, and connector for Patient remote hand set & Patient Remote Handset with flexible cord of 2 meters, Telephone type Jack connector, switceh for call and indication for Ready, Call & Wait.
Supply, Installation, Testing & Commissioning of toilet Pull cord toilet pull Cord with indicator. Rope Length standard 1.5 m
Supply, Installation, Testing & Commissioning of with 8 Nos Red LEDs, Red Acrylic cover suitable for connecting up to 8 beds in one room
Supply, Installation, Testing & Commissioning Digital display Board with 4 digit (Numeric + Alphabet) display with five No.4 Digit display card, Acralic cover and Hooter with volume control in CRCA box. (Suitable for up to 10 points)
Supply, Installation, Testing & Commissioning Digital display Board with 4 digit (Numeric + Alphabet) display with five No.4 Digit display card, Acralic cover and Hooter with volume control in CRCA box. (Suitable for up to 5 points)
Supply, Installation, Testing & Commissioning Call-Response Monitoring Software- This Software is insalled in Computer at Nursing Station. This Software records call & reset time of each Bedside Call Unit &Toilet Emegency Calling Unit. Calls & reset times got highlighted in red if a call is rest after a pre defined time (Say 8 minutes.) One file can record 60,000 entries & 60,000 files can be created on a computer. Pritout can b e taken of call - Rest times in PDF or in card Copy. On going & previous Call & reset times can be seen on computer at Nursing Station.
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm
Internal road and Parking
Internal road : Embankment Construction with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2).
Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) for grading- I Material
Water Bound Macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening / binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density.) By Manual Means Grading- II (Using Screening Crushable type such as Moorum or Gravel) c) Using Screening Type-B (11.2mm Agg.)
iii) Grading- III (Using Screening Crushable type such as Moorum or Gravel) Using Screening Type-B (11.2mm Agg.)
Prime coat (Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means.)
Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom.
Open - Graded Premix Surfacing (Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or cut-back or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades.) Case - I: Mechanical method using Penetration grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour .
Seal Coat (Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A and B seal coats) Case - I : Type A
Parking : Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 1. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.
Note :- While quoting the rates, the bidders should take care that, the rates quoted for same items under different sub-heads are the same. If different rates are quoted by the bidders for same items under different sub-heads, the lowest rates quoted by the bidders will be considered for that particular item.
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid