ADDITION/ ALTERATION AND RENOVATION WORKS IN MI ROOM BLDG No. (P-282) AT DLRL HYDERABAD AND PROVISION OF TWO IN NUMBER SPLIT AIR CONDITIONERS FOR ROOM IN BUILDING NO.P-1 AT CNA(DP), HYDERABAD

Amount

Taking down existing roof treatment of any description, any position with bituminous felt including plaster/loose concrete and removing rubbish to a distance exceeding 500m but not exceeding 1000m and roughening the surfaces of old concrete by picking, scraping, cleaning and washing down with water to remove all dust etc complete specified and directed.

M & L cutting out cracks to V section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as secified and as directed

M&L providing plain cement concrete type B-1, 1:2:4 ( 20mm graded stone aggregate) in roof padding, kerb or mud stop, rounded or chamfered on edges to maintain proper slope on roof slab complete all as specified

M&L for rendering 10mm in CM 1:3 over concrete surfaces on RCC roof slab and parapets mixed with WPC @ 3% by weight of cement shall be carried out complete all as specified and directed. Note : WPC will be measured under separate item of this schedule.

Supply only integral water proofing compound complete all as directed Make :- SCOTT /AQUA PROF/RAILIA

M&L water proofing treatment with polymeric standard membrane of weight not less than 3kg per sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/sqm) laid over primed surface by forced application complete. Shall be fused uniformly by LPG torch flame on horizontal/vertical/slope surface on roof complete all as specified and directed by Engr-in-Charge. Water proof treatment consist of as under: - (i) Applying one coat of bitumous primer conforming to IS 3384 @ 0.3 ltrs per sqm (ii) Laying APP based memberane as specified thickness and weight. (iii) Appplying one coat of bitumen grade 85/25 @1.20Kg per sqm.

M&L for cutting grooves in brick wall 70mm wide and 65mm deep and sweeping horizontal face of groove with cement mortar (1:3) and making good in CM 1:3 after inserting membrane into the groove complete all as specified and directed.

M&L for preparation of surfaces of any description, over 10cm in width or girth otherwise described and appplying two coat of aluminium paint @100ml per sqm over APP membrane sheet complete all as specified and directed by Engr-in-Charge.

Demolition of plain cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness below or above ground level, removal fo rubbish and debris and depositing in low lying areas out side MD land complete all as directed.

Taking down chowkats or frame with shutters (without taking off shutters from frame) but each not exceeding 1.50 Sqm

Taking down Chowkats or frames with shutters exceeding 1.5 Sq. M but not exceeding 4 Sq. M each (Without taking off shutters from the frame)

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm from the frame steel/ wooden/ PVC complete all as specified and directed

Taking down shutters of any description exc 2 Sqm each complete all as specified and directed

S&F 35mm thick flush door shutters of solid core construction with both faces covered with decorative face including all round lipping/ frame with first class teak wood beading complete all as specified and directed.

S&F 35mm thick 2nd class hard wood rail and stile plain framed, panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both face. The size of rail and stile as per IS- 1003 (Part -I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S & F 35mm thick factory made second class hardwood glazed and skelton door shutter kiln seasoned and chemically treated, open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete. The size of members of shutters shall be as specified in MES SSR Part-I.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube of 1.25mm thickness suppling & fixing in opening as per specification & drawing

S/F factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F in repairs mild steel butt hinges medium weight, cold rolled 100mm size complete all as specified

S&F mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified

S&F 150mm long aluminium anodised, barrel tower bolt of extruded section complete all as specified

S&F in repair 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified

S&F in repair 150mm size extruded aluminium alloy handles fabricated type, anodised complete all as specified.

S&F 150mm size extruded aluminium, alloy handles fabricated type, anodised complete all as specified

S&F aluminium alloy anodised sliding door bolts 300mm long with hasp and staple ( bolt type) & fixing clips of sheet or extruded section & fixing bolts & sliding bolts of extruded section.

S&F in repairs 300mm long aluminium alloy, anodised, sliding door bolt with hasp & staple ( bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy complete all as specified.

S&F in repair floor door stopper 150mm of aluminium alloy body and tongue anodised with hard drawn steel spring complete all as specified

M&L preparation of old painted wooden surface of any description, not otherwise described, over 10cm width or girth applying one coat of synthetic enamel paint all as specified

M&L preparation of new or previous untreated surfaces of wooden surface of any description, not otherwise described, over 10cm width or girth applying two coat of synthetic enamel paint over a coat of pink primer all as specified

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or galvanised wire staples all as specified

M & L for Cement concrete type D2, 1:4:8 (using 40 mm graded stone aggregate) in mass concrete of sub base of flooring/ hard standing.

M & L for Machine pressed precast concrete interlocking paver block with grey cement and pigments any shape and size confirming to IS 15658 - 2006 of 60 mm thickness, M - 35 Grade with grey cement and pigment over 40mm thick sand cushioning complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to stores and rubbish off the premises. all as directed.

Roughening surface of old concrete floor by picking,sweeping clean and washing down with water to remove dust etc all as specified and directed.

S&F vitrified ceramic tiles 10mm thick (Square / rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc joint free set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 15mm thick screed bed in CM (1:4) finished fair and even complete all as directed.

All as per item No.35 here-in-before but on vertical surfaces such as skirting (skirting is to be flush with wall ) over 10mm thick rendering in CM 1:4 on fair faces of brick / concrete surfaces as backing coat for tiles complete all as directed.

M&L for Non-skid coloured ceramic joint free tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm in floors/vertical surfaces etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile over 15mm thick screed bed in cement motar 1:4 complete all as specified and as directed.

S&F Glazed coloured ceramic tiles in vertical surface 450 x 300x 7 mm thick, set and jointed in neat cement slurry and pointed in white or cloured cement 10mm thick backing coat in CM 1:4 complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises, removal and depositing serviceable materials where directed and leaving the work clear of any plastering.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement including mixing of water proofing compound wherever required.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement.

M&L rendering 5mm thick in CM 1:3 on fair faces of brick work or concrete on ceiling, finished even and smooth without using extra cement complete all as directed.

M&L for preparation of new plaster surface of existing treatment and applying two coats of distemper oil emulsion over a coat of alkali resistant priming paint on surfaces of walls over a two coats of wallputty (1.5mm each) to make surfaces smooth complete all as directed.

M&L for Complete removal of existing treatment and applying two coats of distemper oil emulsion over a coat of alkali resistant priming paint on surfaces of walls over a two coats of wallputty (1.5mm each) to make surfaces smooth complete all as directed.

Complete removal of existing treatment from external surfaces of walls/ ceiling, washing with water and applying two coats of weather proof antifungal exterior paint as per manufacturers instructions over a coat of true care exterior wall primer over two coats of external birla putty 1.5mm each to level the surface and finshied smooth with emeny paper No.180 followed by emeny paper No.320 or 400 and wipe it clean complete all as specified and directed. Make:- Apex Altima of Asian Paints or techno commercially equivalent in Indigo, JSW

M&L for preparation of new plastered surfaces of walls/ ceiling, washing with water and applying two coats of weather proof antifungal exterior paint as per manufacturers instructions over a coat of true care exterior wall primer over two coats of external birla putty 1.5mm each to level the surface and finshied smooth with emeny paper No.180 followed by emeny paper No.320 or 400 and wipe it clean complete all as specified and directed. Make:- Apex Altima of Asian Paints or techno commercially equivalent in Indigo, JSW

M & L preparing new plastered surfaces and applying three coats of white wash on ceiling complete all as directed.

M & L preparing old plastered surfaces and applying two coats of white wash on ceiling complete all as directed.

Demolition of reinforcement cement concrete ( reinforcement cut as required to faciliate demolition) roofs, floors ( other than ground floors), beams,chajjas and similar suspended work complete all as directed.

M&L for reinforced cement concrete ( nominal mix) type B0 1:2:4 ( 12.5mm graded stone aggregate) as in slabs supported on walls,beams and columns in floors, roofs, landings,balconies,canopies deckslabs andin shelves and the like complete all as directed.

M&L for mild steel deformed TMT bars 10mm dia and over, cut to length,bent to shape required including cranking, bending spirally, or hoping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work not exc 200mm thick ( horizontal or slopping for fair finished surfaces complete all as directed.

Formwork to edges of concrete flats, treads, breaks in floors, concrete railings, opening in concrete walls not exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or slopping and similar work exc 10cm but not exc 20cm wide for fair finished surfaces complete all as directed.

M&L for PCC 1:2:4 type B0 ( using 12.5mm graded stone aggregate) incills, steps, seismic and other damp proofing courses, plinthcourses , water tank base, string courses, lacing courses, parapets and railing upto 60cm in height, coping etc complete all as specified and as directed.

M&L for rectangular aluminium hollow section of size 101.6 x 44x2mm thick as in partition ( including fixing with nut and bolt in floor and wall by drilling holes), powder coated of approved colour for both vertical and horizontal member including 5.5mm thick glass, 12mm thick particle board prelaminated on both side, aluminium legs, aluminium glazing channel, rubber beading as required complete all as directed.

All as per item No.56 here-in-before but as in door, powder coated, approved colour, including 5.5mm thick glass, 12mm thick particle board prelaminted on both side, rubber beading, aluminium glazing channels, two Nos handle, three Nos extruded aluminium hinges 100mm long, two Nos 200mm aluminium anodised, barrel tower bolts of extruded section, one floor door stopper 150mm of aluminium alloy body, 100mm size brass mortice lock, 4 levers with two keys and floor door spring as required for door complete all as specified and directed.)

M&L for preparation of old decorated wooden surfaces of any description not otherwise described over 10cm girth or width and applying two coats of French polishing complete all as specified and as directed.

S&F solar control film 25 micron reflective type sticked to glass panes as per instruction of manufacturer complete all as specified and directed. Make :- Gareware sun control or equivalent

Demolition of old existing unserviceable WHB glazed and S&F vitreous china wash hand basin white of size 550 x 400mm flat back excluding taps, waste china and plug but including brackets, CP waste fittings 32mm dia including cutting for and pinning in ends of brackets or erecting stand complete all as directed.

S&F in repairs Vitreous wash down water closet pan (Pedestal pattern), (EWC) white inclduing plastic water closet seat, white, closed pattern with flat bottom, cover and mild steel chromium plated or aluminium hinging device and fixing bolts complete all as specified and directed.

S&F in repairs Vitreous China Half stall urinal White complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets.

S&F in repair vitreous china squatting pan 'Orrissa pattern' size 580 x 440mm white , with integral foot rest, suitable CI trap includingconnection to trap, flushing pipe, antisyphonage pipe etc, including trap set in and including concrete and making good to floor complete all as specified and directed.

S&F sink with drainage board made of stainless steel 1.0mm thick for kitchen with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or fixing cantilever brackets and connecting union to pipe, overall size 1120mm x 457mm bowl size 460 x 330 x 203mm includng waste pipe of polythelene of flow or high density or PVC 32mm dia & waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including making holes in stone walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0 complete including taking down of existing old sink.

Taking up or down steel tubing and connections, Supply and fixing 15mm dia GI steel tubes, medium grade with all fittings and fixed complete to wall and ceiling or laid in floors all as specified and directed.

Taking up or down steel tubing and connections, Supply and fixing 20mm dia GI steel tubes, medium grade with all fittings and fixed complete to wall and ceiling or laid in floors all as specified and directed.

S & F 1000 Ltrs capacity rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe pipe etc complete all as specified in SSR Part I, Make - Sintex or eqivalent including dismantling old water tanks

S & F Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed bore dia of pipe 20mm

S & F in repairs stop valves cast copper alloy screwed down high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 20 mm bore fixed

S & F in repairs waste coupling suitable for urinal and sink etc., of PTMT (Half or full threaded) of minimum weight 45 grams, and fixed to discharge pipe of 32 mm dia., bore complete all as directed.

S & F in repairs Brass Chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges complete all as directed.

S&F in repair stop valves cast copper alloy screwed down high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 15 mm bore fixed complete all as directed.

S&F in repair angle stop valves cast copper alloy, fancy type chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 15 mm bore fixed complete all as directed.

S&F in repair PVC connection 15mm dia 450mm long with 2 Nos brass check nuts with washer complete all as specified

S&F in repair PVC connection 15mm dia 600mm long with 2 Nos brass check nuts with washer complete all as specified

S&F in repair Bib taps, cast copper alloy chromium plated, fancy type with crtuch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 15mm bore fixed complete all as directed.

S&F in repair fancy type pillar tap cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in stone, concrete block or slab wall.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters walk ways, railing, frame work of water tanks and similar works conforming to Fe-290, Gde -E- 165 complete all as directed.

Demolition of stone or brick masonry built in cement mortar or cement lime mortar incl all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as directed.

M & L Brick work with sub class ‘B’ bricks straight or curved on plan exc 6 mtr mean radius using old size brick built in CM 1:6 complete all as directed.

M & L precast PCC blocks or slabs 150 mm thick (1:2:4) mix type B-1 using 20 mm graded aggregated with plain or interlocking joints as directed complete in walls setting in CM (1:6) complete all as directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing white cement (1:2) using marble dust with admixture of pigment to match the shade of granite including cutting grooves and nosing including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

S&F steel rolling shutters 1.25mm thickness of laths without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer , erected in position as indicated, complete push pull or manual type complete all as directed.

M & L preparing new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zink chrome primer complete all as directed.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil complete all as directed.

M&L plain cement concrete type B-1, 1:2:4 (20mm graded aggregate ) in roof kerbs or mud stops, rounded or chamfered on edges complete all as directed.

M&L of aluminium (extruded section body) door closer hydralically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as directed.

Demolition stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in cement mortar complete all as directed.

Cutting opening through brick walls built in cement mortar for door, window and other opening or enlarging existing opening , converting window into door opening etc or cutting out defective brick work for under pinning , including providing fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable brick hard core etc to store and rubbish not exc 50m complete all as directed.

M&L plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in plinth protections 75 mm thick finished even and fair with joints 10 mm wide and in full depth at corners and @ 3m c/c filled with mastic mortar complete all as directed.

S&F in repair grating doom 125mm dia with waste hole of PTMT ( minimum weight 40 gms) complete all as directed.

S&F in repairs 10 ltrs capacity, PVC valve less, syphonic action type, flusihing cistern, low level, white with inlet, ball valve, float and handle including brackets and suitable flush pipe PVC 32mm dia complete all as specified and directed.

Dismantling of existing AC/PVC soil and waste and rain water pipe 100mm dia including fittings,viz, bends , tee from walls complete all as directed.

Dismantling of existing AC/PVC soil and waste pipe 75mm dia including fittings,viz, bends , tee from walls complete all as directed.

M & L for PVC (SWR) plain Floor trap of 75 mm dia., outlet with grating including jointing with solvent cement complete all as directed.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches complete all as directed.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches complete all as directed.

S&F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as directed.

S & F 110 mm bore PVC (SWR) Soil,rain water, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as directed.

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as directed.

S & F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as directed.

S & F 110 mm bore PVC (SWR) Vent Cowl complete all as directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as directed.

S & F UPVC three track multicavity frame section 75mmx64mmx205mm suitably reinforced with GI and shutter made out of 5mm thick tinted glass in windows alongwith sliding wire mesh shutter. All sections of frame, sashes, transom and mullion shall be reinforced with G/J/U/O shape galvanised MS section considering structural/wind load requirements. All the corners/mullion/transom joints of the frame & sash shall be mitred cut fusion welded with out any mechanical jointing. all welded joints are neatly trimmed & feature grooved and raised nib finish so as to make the finish product free from all sharp edges & burrs. System shall have adequate drianage mechanism to permit the escape of water from horizotal member beneath in each unit. Shall be provided suitable uPVC beads for glazing and fitted with inner and outer EPDM weather seal gaskets.To be provided with proper operative and locking hardware mechanism, frame to be fixed to wall with high quality fasteners and silicon glue is to be applied to fill up gap between frame and wall to make leak proof all as specifed and as per Manufacturer instructions.

S&F UPVC fixed ventilator of white colour classic premium series incl 5mm toughened glass complete all as directed by Engr in Charge

M&L aluminium anodised snap grid frame work for false ceiling grid size 605 x 605mm with runners aluminium anodised main Tee of section 35 x 35x 1.5mm thck, cross Tee of section 25 x 25 x 1.5mm thick and aluminium anodised angle of size 25mm x 1.5mm thick section complete all as specified.

S&F hangers 6mm dia GI ( upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified

M&L for providing 12mm thick Gypsum board ( 600 x 600mm) in ceiling fixed with screw as per manufacturers instructions

S&F venetian blinds ( vertical type) of 100mm wide straps with all fittings ( to be matched with existing patterns) & taking down old venetian blinds complete all as specified and directed.

Taking down existing unserviceable false ceiling of any description, thickness any position including channels, sections,angles etc complete all specified and directed.

Supply & Fixing, Commissioning and Testing of the 2 Loop micro processor based Analog addressable fire alarm control panel with battery backup, Networkable. Make :- Honeywell

Supply, Fixing, Commissioning and testing of the analog Addressable multi sensor smoke/ Heat detector. Make :- Honeywell

Supply, Fixing, commissioning and testing of the analog Addressable Sounder with fixing accessories.

Supply, fixing, commissioning and testing of the analog Addressable fault isolators. Make :- Honeywell

Supply, fixing, commissioning and testing of the analog Addressable Manual Call Point Make :- Honeywell.

Supply and fixing Response indicator for analog addressable Make : Honeywell

Supply and fixing and testing of twisted pair 1.5 sqmm 650 Volts grade shiled FRLS copper conductor flexible wire drawn through existing 25mm conduit. Make : Neolex or Equivalent.

Supply, Installing and testing of I/O Module. Make : Honeywell.

Taking down carefully of any type point wiring light fans socket or power complete fitting such as switch ceiling roses, pendent, regulator, sockets etc removing material and making good disturbed surface of wall floor etc complete all as directed.

M&L Point wiring complete with ISI marked 1.5 Sqmm single core PVC insulated unsheathed cable 1100 Volts grade with multistranded copper conductor drawn through in and including medium grade PVC conduit and accessories concealed in wall suitable for terminal boxes for fixing modular switches, sockets etc including suitable size modular plates concealed in walls and 1.5 Sqmm copper conductor as earth continuity to connect common earth dolly complete for the following all as specified and directed:- NOTE:- The quoted rate shall deemed to include for modular cover plates with frame of any colour and metal flush boxes of any type and size.

(a) One light point controlled by one 5 Amps one way switch.

(b) One ceiling fan /exhaust fan point controlled by one 6 Amps one way switch

(c) One 3 pin socket outlet 6 Amps on the same board with other switches.

(d) One 3 pin 6 Amps switch socket outlet point on independent board

Description all as per item No 02 here in before but for 15 amps socket outlet with 2.5 Sqmm Copper incl 1.5 Sqmm PVC insulated copper conductor cable as earth continuity conductor and connecting to common earth dolly complete all as specified and directed.

S&F modular type 06 Amps, 05 pin mulitipurpose switch, socket outlet 03 Nos and 16 Amp multipurpose switch, socket outlet 01 Nos on one switch board concealed in wall suitable for terminal boxes for fixing of switch sockets etc including suitable size modular plates and including all internal elctrical connections with copper conductor complete all as specified and directed.

S&F modular type 06 Amps, 05 pin mulitipurpose switch, socket outlet 04 Nos on one switch board concealed in wall suitable for terminal boxes for fixing of switch sockets etc including suitable size modular plates and including all internal elctrical connections with copper conductor complete all as specified and directed.

S&F Modular Switch 1 way, 6 Amps 1 Module complete all as specified.

S & F modular switch 1 way, 16 amps, 1 module complete all as specified

S & F Modular sockets, 6 amps 2/3 pins combined 2 module complete all as specified

S & F Modular sockets,16 amps 5 pins combined 2 module complete all as specified

S & F Modular fan regulator, 120 watts, 2 module complete all as specified. Note :- Fan Regulator only taken for Ceiing Fan not for wall mounting fans.

Supply and fixing Sheet Metal enclousure Plug and socket type DB (Functional Unit) 20 Amps capacity with provision of single pole 20 Amps MCB, plug top and earth plug, grouted flush to walls complete all as specified.

Dismantling of existing unserviceable MCB distribution board and S&F sheet metal enclosure DB concealed with wall having facility to fix MCCB as incomer and MCBs in outgoing, TP vertical type 8 way of double door, complete fitted with bus bars, neutral links, G frame including S&F 3 pole MCCB 100 Amp capacity, 50 Hz, 16 KA Breaking capacity, blanking plates including making good disturbed surfaces complete all as specified and directed.

S&F Sheet metal enclosure TPN DB 4 Way Double Door including all connections.

S&F Sheet metal enclosure DB 8 Way SPN Double Door including all connections.

S&F MCB TPN 32 Amps 415 volts complete all as specified and as directed.

S&F MCB SPN 5 to 40 Amps 230 volts complete all as specified and as directed.

S&F MCB SP 5 to 40 Amps 230 volts complete all as specified and as directed.

Supply & Fixing LED fitting.Circular suspended fully diffused LED Lumunaire Decorative for Main Enterance of Building , 34 w , 230v Energy efficient, with Drive , connecter block/ with universal susupension system with quick onsite adjustment mounting with 2 nos suspension on celing, etc. complete with mounting arrangement and all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Wipro Model No LM71-441-XXX-57-XX.

&F LED 2'x2' type recess mounted lumniaire 24 Watt, 3000lm out put with Drive, connector block, etc. complete with all accessories internally pre-wired and including connecting up 3 core sheathed copper flexible cable 1.5 sqmm up to light fitting and connecting testing complete fixed on false ceiling complete. Make-LCTLRN-24FO- CDL CG or equivalent in Philips.

Supply & Fixing LED fitting.indoor Batten light , 1 x 24 w , output 2500 lm 230v Energy efficient, Box type aluminium housing ,with Drive , connecter block, etc. complete with all accessories internally pre-wired and including connecting up with twin core hvisted flexible copper conductor cable with suitable size. Make- BN021LED10S 6500PSU GR S1 of Philips or equivalent in Wipro/Crompton.

S&F1x30W LED road way lighting luminaries with Pressure die-cast powder coated LED streetlight suitable for Building light clear acrylic cover and complete accessories including Drive with suitable connection complete all as specified and directed Make- LSTS-30 CDL CG or equivalent in Philips

M&L for submain wiring comprising single core, 4 runs of 10 sqmm nominal cross sectional area multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade drawing in and including appropriate dia. PVC conduits and conduit fittings complete including 2 X 10 sqmm nominal cross sectional area multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade earth wire complete incl taking down old UNSV sub main all as specified. Note :- 6 runs of 10Sqm and 1 run of PVC conduit shall be measured and paid as oone unit.

Description all as per Item No.142 above but with 4 runs of 6 Sqmm copper cable and 2x6 Sqmm as earth continuity conductor complete all as directed.

Description all as per Item No.142 above but with 2 runs of 4 Sqmm copper cable and 1x4 Sqmm as earth continuity conductor complete all as directed.

Taking down ceiling fan/ exhaust fan/ Wall mounting Fan of any make, sweep and dismentling, cleaning , greasing, overhauling and providing two coat of synthetic enamel paint of existing colour and refixing to its existing place including connections with new flexible cable 3 core copper conductor complete. For Ceiling fan - adjustment for providing new down rod including new canopy, clamp, rubbr reel, all as directed.

Taking down carefully existing serviceable split type AC unit of any capacity with mounting brackets carrying out the necessary servicing and overhauling with water chemical air cleaner, filter and drying, checking the bolts and nut connections,and refixing the same its original location after completion of building renovation work all as directed.

Renewal of copper tube of size 5/8 inch dia includng necessary soldering , flooring and connecting and testing in between indoor to out door units of split type AC 1.5 Ton complete all as specified and directed.

Renewal of copper tube of size 1/2 inch dia includng necessary soldering , flooring and connecting and testing in between indoor to out door units of split type AC 1.5 Ton complete all as specified and directed.

Renewal of insulation felt for split type AC 1.5 / 2.0 Ton copper tube inlet/outlet to out door unit complete all as directed.

Supply & fix Air Circulator fans 230 volts single phase oscillating 450 mm sweep suitable for wall mounting

Cutting to existing steel tubing for alterations upto 50 mm GI tubing

Pipes galvanized, for Drinking Water (Manjeera Water) “Medium class”, supplied And laid complete including fittings 50 mm (2.0”) dia.

Pipes galvanized, “Medium class”, supplied And laid complete including fittings 40 mm (1.5”) dia.

Pipes galvanized, “Medium class”, supplied And laid complete including fittings 25 mm (1.0”) dia.

Pipes galvanized, “Medium class”, supplied And laid complete including fittings 15 mm (1/2”) dia.

S&F Cast copper alloy Stop Valve, 50 mm size screwed down, high pressure, with butterfly handle screwed both end for iorn pipe.

S&F Cast copper alloy Stop Valve, 25 mm size screwed down, high pressure, with butterfly handle screwed both end for iorn pipe.

Ball brass valves, 25mm size high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed.

S&F Bib taps, 20mm dia cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in soft/loose soil for foundation of poles, structures, stay rods, laying of underground cable etc complete all as directed.

Returning, filling in soils including spreading, leveling, watering and well ramming in layers each not exceeding 25cm thick complete all as directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as directed.

Material and Labour for cutting existing BT road/PCC of size 45cm x 60cm for taking out/laying of underground cable and including necessary earth work and refilling the same in layers well ramming including watering as required and matching with the existing surface with 200mm thick PCC 1:2:4 type B1 and curing the same with wet gunny bags and removing debris to a distance not less than 50m complete all as specified and directed.

Sofa 3 seater (TP) Model: Parto of Godrej

Visitor Chair (TP) Model: FU 7112R of Godrej

Revolving Chair (TP) Model: FU 7102 R

Almirah Steel size 1981x916x486 with 4 shelves Model: Storewell plain of Godrej

Supply and install 5 star inverter type hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air loniser and plasma filter for better indoor air quality inverter type of capacity 1.5 TR with CFC free refrigerant gas like R-410 suitable to operate on 2300V single phase supply, including refrigerant, copper tube of suitable dia from indoor to outdoor unit, insulation felt to copper tubing, power cable/controll wiring from indoor to outdoor units, supply power cable & connection through stabilizer to indoor unit, provision of rigid UPVC condesate drain piping from indoor unit to ground level etc., complete all as directed. Make: LG/ VOLTAS/ BLUE STAR

Supply and install teseting and commissioning voltage stabilizer for autoatic correction and operation single phase neutral air cooled split type and designed for input various between 170 to 250V with output stabilier at 230V with necessary +/- 2.5% and capacity of 4 KVA complete all as directed. Make : VOLTAS/V-GUARD/K-LINE/BLUE BIRD

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amp 240V, 'C' characteristic, 10KA breaking capacity for AC connection complete all as specified and directed.

M&L for point wiring complete with 2.5Sqmm PVC insulated unsheathed single core multi standard copper conductor 1100V grade drawn through in and including 20mm dia PVC conduit concealed on walls/ in existing conduit on ceiling and terminated to sunken box of modular type including white cover plates suitable for fixing switches, sockets etc including 2.5Sqmm PVC insulated copper conductor cable as earth continuity conductor and connecting to common earth dolly and taking down old one complete all as specified and directed for 3 one 3 pin socket outler 15 amps independent:-

Sai construction & services

asmath enterprises

BHAGYARAM ENTERPRISES

M/S AKSHATHA ENTERPRISES

SHAH ENTERPRISES