PREVENTIVE REP REPLACEMENT MAINT OF LT SWITCH GEAR CAPACITOR BANK APFC PANEL SERVO VOLTAGE STABILIZER IMPROVEMENTS OF SUB STN INCL REPLACEMENT OF EARTHING CABLE DUCT COVER PAINTING REP OF PANELS REPLACEMENT OF GLOWSIGN BD OTHER CONNECTED WKS AT NSK

Amount

M&L for dismantling of existing panel including disconnecting connected cables, etc. and supplying, installing, testing and commissioning of factory made having CPRI Approved LT cubical double door panel with roof canopy, Outdoor type, of Suitable to accomodate the following accessories made out of CRCA sheet 3 MM thick duly powder coated with Seimens Grey Shade RAL 7032, totally enclosed, dust and vermin proof outer cubicle. Inner cubicle should be made out of 2 MM thick CRCA sheet with working voltage of 415V, 50 Hz, 3 phase 4 wire fully compartmentalised with single door system for each compartment. Outer cubicle having both sides door openable. Bus bars provided shall be adequately supported on insulators to withstand dynamic stresses due to short circuit current and shall be suitably colour coded with heat shrinkable sleeve for phase indication. The standard phase arrangement when facing the switchgear shall be R-Y-B from left to right. The bus bar connections and their insulated supports shall be mechanically strong, and shall withstand all the stresses which shall be imposed upon them in ordinary working due to fixing, vibration, fluctuation in temp., shot-circuit or other causes. The bus bar should be supported on DMC. Provision shall be made for expansion and contraction of the bus bars and connections with variation of temp. Internal wiring should be done with 2.5 sqmm multi-stranded copper conductors and shall be properly bunched, tied, ferruled for proper identification, crimped and shall be connected with suitable lugs and PVC sleeves, etc. The bottom of the panel should contain detachable plate having provision for entry of armoured cable of adequate size with glands. Threaded earthing studs - 02 Nos shall be provided at the bottom and lifting lugs of suitable size at top to lift the panel safely shall be made. The cubicle incomer MCCB as well as outgoings shall have copper TPN/TP extension links of current rating not less than 1.5 times the rated capacity of individual feeders with Ics = 100% Icu in all MCCBs with extended Rotary Handle. The cubicle should be inclusive of following :

Supply and fixing in repairs LED building security light fitting with suitable size bracket/angle to fit security light of 60w IP 66 protection LED complete all as specified & directed

M&L for street light bracket 1.5 mtr long made out of 40mm dia medium grade GI tube one and duly welded with 100mm dia 30 cm long GI tube including provision of 4 Nos holes duly threaded for fixing the bracket on the top of existing poles with complete including arrangment of threding and weldeding work required for fixing of street light fitting complete all as specified and directed

M & L for PCC type C2, 1:3:6 using (40 mm graded stone aggregate) in foundations of poles / struts includings necessary form work complete all as specified & directed

M & L for PCC type B-1, 1:2:4 using (20 mm graded stone aggregate) for pole / strut coping, including form work complete all as specified & directed

Supply and installation of steel tubular swaged pole complete with cast iron base plate, finial taper plug, bolts, nuts, and screws as specified type confirming to IS 2713 complete including 2 coats of aluminium paint over one coat of red oxide primer on external exposed surfaces and 2 coats of black bituminous paint on portion embedded in concrete including taking down old existing pole any type complete all as specified and directed for the following:- NOTE :- Excavation and earth work and PCC foundation and plinth will be measured and paid separately under respective items of Sch ‘A’

(a) 410 SP-31 (9 mtr long)

(b) 410 SP -22 (8.5 mtr long)

M & L earthing complete with GI earth plate electrode of size 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below the normal ground level connected with GI strip 32 x 6 mm by means of bolts, nuts, check nuts & washers of galvanished iron steel including necessary excavation and earth work in any type of soil, removing surplus soil to a distance not exc 50 m, with and including PCC chamber in PCC (1:2:4) , type B1, using (20 mm graded stone aggregate), mild steel angle iron frame made out of MS angle iron of size 40x40x6 mm thick duly painted with two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer hinged with and including 6mm thick CI cover with handle, watering arrangement with funnel internally secured with wire mesh with 20 mm dia medium grade pipe for watering ,40 mm dia light grade GI pipe for lead protection in & including alternate layers of charcoal dust and common salt complete all as shown in electrical plate No 3 of SSR Part-1(2009) connected to earthing test point including testing on completion & dismantling/ taking out old existing earthing complete all as specified and directed Note :-(i) copper strip upto 7.5 m will be deemed to be inluded in quoted rate (ii) The earth chamber shall be constructed 50 cm away from the edge of earth pit & the cost of the same is deemed to be included in rate quoted for above items. (iii) The rates quoted are also deemed to be included for cost of new test point as specified.

Disconnecting 1.1 KV grade XLPE cable of any size from structure/pole/ transformer/LT panel/FPB for finding fault and its location including cutting faulty cable to facilitate joint and testing remaining part of cable for any further fault using cable fault locating equipment including bringing approved cable fault locating equipment & to be taken back after finding fault is over complete all as specified and directed.

M&L Danger notice plate of 1.6 mm thick mild steel sheet,vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S Clamps, bolts and nuts of size 20 x 15 cm complete all as specified and directed.

Supplying, fixing, jointing, connecting & testing in trenches XLPE/PVC insulated PVC sheathed cable heavy duty 1100 volts grade, aluminum conductor in trenches / ducts /on wall surface including taking down old existing cable, any type of following sizes all as specified and directed.

3.5 core 25 Sqmm

3.5 core 35 Sqmm

3.5 core 50 Sqmm

3.5 core 70 Sqmm

3.5 core 150 Sqmm

3.5 core 240 Sqmm

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr depth and getting out in any type of soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr wide and depth exceeding 1.5mtr but not exceeding 3.0 mtr and getting out in any type of soil complete all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layers n.exc 25cm complete all as specified & directed.

Removing excavated materials to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M & L for dry river sand as sand cushioning for protection of UG cable including punning of sand in layers complete all as specified and directed. Note: Punned thickness will be measured and paid.

Supply & laying un-reinforced precast concret cable cover class LV type 1, flat size 250mm x 150mm x 40 mm complete all as specified and directed.

Laying only un-reinforced precast concret cable cover class LV type 1, flat size 250mm x 150mm x 40 mm complete all as specified and directed.

Taking down carefully copper/aluminium point wiring ( light, fan socket or powder) complete, including fixtures fitting such as switches, ceiling roses , pendants regulators socket etc. removing material to store for keeping in safe custody or for taking credit and making good disturbed surfaces walls, floors etc. complete all as specified and directed.

M&L for point wiring in steel conduit 20 mm dia or more confirming to IS 2079-1973 medium grade in concealed with PVC insulated unsheathed multistranded copper conductor cable( FRLS) 1.5 sqmm nominal cross sectional area 1100 volts grade complete with all fittings such as Elbow, bends, junction boxes, saddles incl sunk 20mm dia medium grade steel conduit (2mm wall thickness minimum as per IS-9537) (ISI marked) pressed steel not less than 2 mm thick, 50 mm deep terminal boxes with 3mm thick ISI marked minimum width 25 mm, white/creamy colour, plastic laminated sheet top cover fastended with chromium plated brass screws including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts Multistranded copper conductor green colour as continuous earth wire connected to common earth dolly complete all as specified and directed. for the following:- Note:- Rate shall be included for Cutting of wall for the concealed conduit & mathcing with existing surface to be included in item rate.

One light point/fan point/ exhaust fan point controlled by one 5 Amp switch

One multi pin socket outlet 5 Amps independent complete

All as per BOQ item No 21 here -in- before but with 4 sqmm cable for one 3 pin socket outlet 15 Amps multipurpose as in independent board including 1.5 sqmm PVC insulated unsheathed multistranded copper earth continuity wire connected from common earth point complete all as specified and directed.

S&F switch piano flush button single pole one way, 5 Amp complete all as specified and directed.

S & F switch socket outlet 2 in 1, 3 pin 6 Amp , complete all as specified and directed. .

S&F switch socket outlet multi purpose 5-in-1, 15 Amp controlled by one switch , complete all as specified and directed.

S&F ceiling rose surface bakelite 65 x 50mm, three terminals , all as specified and directed.

S&F step type electronic regulator 80 watt flush type on the existing phenolic laminated sheet complete all as specified and directed.

S&F LED Tube light fitting 1x18 watt with LED tube fixed on wall and conection with ceiling rose including taking down old existing fitting, any type complete all as specified an directed.

S & F SPN 8 way vertical type DB double door 240 Volts including taking down old existing DB any type complete all as specified and directed.

S & F SPN 4 way vertical type DB double door 240 Volts including taking down old existing DB any type complete all as specified and directed.

S & F SPN 2 way vertical type DB single door 240 Volts including taking down old existing DB any type complete all as specified and directed.

S & F SP MCB 240 V 50 Hz 10 KA confirming to IS 8828 of rating 5 to 32 Amp complete all as specified and directed.

S&F MCB SPN, 240V, 50Hz, 10 KA , conforming to IS 8828 of rating 32 Amp complete all as specified and directed.

S & F MCCB -DPX3 160 thermal & magnetic type 4 pole 415 volt 25 kA breaking cap. adjustable thermal release range 100 Amps in replacement/ repairs complete all as specified and directed.

S & F MCCB -DPX3 250 thermal & magnetic type 4 pole 415 volt 36 kA breaking cap. adjustable thermal release range 250 Amps in replacement/ repairs complete all as specified and directed.

S & F On load change over switch as sheet steel enclosure 63 A, 415V,AC 4P in replacement/ repairs complete all as specified and directed.

S & F On load change over switch as sheet steel enclosure 100 A, 415V,AC 4P in replacement/ repairs complete all as specified and directed.

S & F On load change over switch as sheet steel enclosure 250 A, 415V,AC 4P in replacement/ repairs complete all as specified and directed.

S & F On load change over switch as sheet steel enclosure 400 A, 415V,AC 4P in replacement/ repairs complete all as specified and directed.

S & F On load change over switch as sheet steel enclosure 630 A, 415V,AC 4P in replacement/ repairs complete all as specified and directed.

S & F Automatic Transfer Switch (ATS) with enclosure of capacity 630 Amps with inbuilt time delay, primary protection against single phasing, over voltage, under voltage available with 12V DC control in replacement/ repairs complete all as specified and directed

Supply and fix in repairs 1.1 KV straight through joint kit 3.5 core 25 sq mm to 50 sqmm complete all as specified and directed

Supply and fix in repairs 1.1 KV straight through joint kit 3.5 core 70 sqmm to 120 sq mm complete all as specified and directed

Supply and fix in repairs 1.1 KV straight through joint kit 3.5 core 150 sq mm to 185 sqmm complete all as specified and directed

Supply and fix in repairs 1.1 KV straight through joint kit 3.5 core 240 sq mm to 300 sqmm complete all as specified and directed

Supply and fix in repairs 1.1 KV straight through joint kit 3.5 core 400 sq mm complete all as specified and directed

Taking out carefully LT UG cable following sizes after necessary excavation , removing of soil, precast cable cover and setting aside for reuse complete all as specified and directed Note: Excavation & earthwork shall be deemed to include in the quoted rate.

2 core, 10 to 25 sqmm

4 core, 16 to 50 Sqmm

4 core, 70 to 120 SQmm

3.5 core, 150 to 240 sqmm

Relaying of LT UG cable of following sizes, laying of cable cover and filling of soil complete all as specified and directed.

2/3.5/4 core 10 to 25 sqmm

3.5/4 core 16 to 50 Sqmm

3.5 core 70 to 120 SQmm

3.5 core 150 to 240 sqmm

Taking out cable loop after necessary excavation ,cutting the burnt out damage end of cable ,refixing the cable providing suitable size of brass cable gland and aluminium lugs complete with all necessary connection with the existing system and refilling of excavated soil making finishing with the existing ground surface for the following sizes:- Note: Excavation & earthwork shall be deemed to include in the quoted rate.

2 core 10 to 25 sqmm

4 core 16 to 50 Sqmm

4 core 70 to 120 SQmm

3.5 core 150 to 240 sqmm

Supply and filling in layers n.exc 25cm thick with 40mm graded coarse aggregates in structures complete all as specified and directed.

M&L Glow sign board 3mm Acrylic shut and 1.25 inch molded LED letter for writting of " GARRISON ENGINEER (NW) KRANJA 22 KV ELECTRIC SUB STATION - " A " with one side CORPS OF ENGINEERS logo and another side Div sign on board complete with support frame of 3mm aluminium composite panel with 1" x 1.5" alumnium pipe complete with fixing on wall surface by using of MS clamp Nut, bolt ,anchor fastioner etc including taking down of existing sign board any type complete all as specified and directed

M&L Glow sign board 3mm Acrylic shut and 1.25 inch molded LED letter for writting on both sides " GARRISON ENGINEER (NW) KRANJA 22 KV ELECTRIC SUB STATION - " E " with one side INDIAN NAVY logo and another side Div sign on board complete with support frame of 3mm aluminium composite panel. The dimensions of the board are 5.87m x 0.61m with alumnium pipe complete, fixing on gate pipes using hollow pipes fixed with the board by using of MS clamp Nut, bolt ,anchor fastioner etc including taking down of existing sign board any type complete all as specified and directed

M&L Glow sign board 3mm Acrylic shut and 1.25 inch molded LED letter for writting of " GARRISON ENGINEER (NW) KRANJA 22 KV ELECTRIC SUB STATION - " DBM3 " with one side CORPS OF ENGINEERS logo and another side Div sign on board complete with support frame of 3mm aluminium composite panel with 1" x 1.5" alumnium pipe complete with fixing on wall surface by using of MS clamp Nut, bolt ,anchor fastioner etc including taking down of existing sign board any type complete all as specified and directed

S & F in repairs Pressure die cast aluminium housing LED street light luminaires with IP66 ,EDGE Series,72 Watt & accessories and connecting up to looping box with PVC insulated multi stranded copper conductor cable 1.5 sqmm twin Core all as specified and directed.

All as per BOQ item No 54.00 above but Cat ref No BRTFG 90 W LED I complete all as specified and directed

All as per BOQ item No 54.00 above but Cat ref No BRTFG 120 W LED I complete all as specified and directed

S & F in repairs LED floodlight luminaire with secondary optics made in pressure die cast housing and heat sink in aluminium extrusion with IP66, Turbo LED series ,120Watt & accessories and connecting up to looping box with PVC insulated multi stranded copper conductor cable 1.5 sqmm twin Core complete all as specified and directed

M&L GI pipe light grade with all fittings complete laid in trenches including taking down of old pipe any type for 40 mm bore of pipe complete all as specified and directed

M&L GI pipe light grade with all fittings complete laid in trenches including taking down of old pipe any type for 50 mm bore of pipe complete all as specified and directed

M&L GI pipe light grade with all fittings complete laid in trenches including taking down of old pipe any type for 80 mm bore of pipe complete all as specified and directed

M&L for cleaning of sub-station Bldg from inside and outside by brooming /scrasing of wall/floor /roof and taking out LT cables from duct after disconnecting from LT panel and relaying of cable with properly dressed, refixing the duct cover and reconnecting the cable to LT panel including area cleaning of sub stn by cutting of tree, bushes, roots, crepers and taking out the bushes from the sub-staion boundaries and depositing within a distance of 1 KM radius complete all as specified and directed

M&L for Painting to electric control panel/APFC Panel/LT Panel/Feeder Piller box /Bus bar panel any type and any size of E/M installations by cleaning the existing old paint with the help of mechanical tools such as wire brush, scraper and sand paper from the surface of panel and painting the prepared surface with two coat of synthatic enamel paint of approved shade over a coat of red oxide primer complete all as specified and specified.

S&F automatic power factor control relay of 8 stage supply Voltage - 230 V AC and current Input - 1A or 5 A,Steps- 8 relay outputs ,Supply Voltage - 1Ph 230 VAC (-20% to +10% ),Measurement Voltage : 1Ph 2 wire 230 VAC (-20% to +10% ) ,Operating temperature : 0 to 70 º C , COMPACT 96 X 96 MM Front fascia of M/S EPCOS CAT NO.BR4000,PFC CONTROLLER-BR-4000-08 ST-RELAY 230V Material Code - B44066R4808A230N 1 or equivalent in Schnieder/ABB/Syntron including testing, connecting, commissioning in such a way to avoid "controller hunting" including taking down of old APFC relay, any type/capacity as specified and as directed having following features - a) Microcontrller logic for measurement b) User frindly operation c) Control mode : binary , unequal and user defined d) Multifunctional LCD display e) Single CT sensing for balanced loads f) Individual harmonic measurement upto 15th order

S&F automatic power factor controller of 12 stage supply Voltage - 230 V AC and current Input - 1A or 5 A,Steps- 12 relay outputs ,Supply Voltage - 1Ph 230 VAC,Measurement Voltage : 1Ph 30V-525V AC (L-N) or (L-L),Operating temperature : 20 to 60 º C , of M/S EPCOS CAT NO.BR6000,PFC CONTROLLER-BR-6000-12 STP-RELAY 230V Material Code - B44066R6012R230N 1 or equivalent in Schnieder /ABB /Syntron including testing, connecting, commissioning in such a way to avoid "controller hunting" including taking down of old APFC controller any type/capacity as specified and as directed having following features - a) Microcontrller logic for measurement b) Self explanatory menu navigation in several languages c) Self optimizing control capability d) Control modes: LIFO, FIFO and Self optimized Intelligent Control. e) Large and multifunctional LCD with backlit display (2 X 16 characters) f) Single CT sensing for balanced loads g) Dual target Power Factor setting (available in 12 stage) - useful for utility and DG mode operation available optional h) Automatic synchronization possible j) Display and storage of maximum values, number of switching operations and operating time k) Recall function of recorded values l) RS232 Interface optional m) Alarm output optional n) Dynamic Power Factor Controller (Transistorised) available in 6 and 12 steps o) Cascading possible with master slave versions p) Protective earth terminal to reduce noise and unwanted interference signals q) EMI/ EMC type tested r) Individual Harmonic measurement th upto 19 order.

S&F Capacitor square cap EHDLL - 440 V (AC) , 3phase, 50 Hz, of capacity 2 kVAr including testing, commisioning including taking down of old APFC capacitor any type/capacity complete all as specified and directed.

All as BOQ serial no. 65.00 but of capacity 5 kVAr including testing, commisioning including taking down of old APFC capacitor any type/capacity complete all as specified and directed.

All as BOQ serial no. 65.00 but of capacity 10 kVAr including testing, commisioning including taking down of old APFC capacitor any type/capacity complete all as specified and directed.

All as BOQ serial no. 65.00 but of capacity 15 kVAr including testing, commisioning including taking down of old APFC capacitor any type/capacity complete all as specified and directed.

All as BOQ serial no. 65.00 but of capacity 20 kVAr including testing, commisioning including taking down of old APFC capacitor any type/capacity complete all as specified and directed.

All as BOQ serial no. 65.00 but of capacity 25 kVAr including testing, commisioning including taking down of old APFC capacitor any type/capacity complete all as specified and directed.

Supply & fix power capacitor heavy duty contactor 3 phase with auxilary switch block 415 volts suitable for 8.5 kVAR including testing connecting commissioning including taking down of old capacitor any type/capacity complete all as specified and directed.

Supply & fix power capacitor heavy duty contactor 3 phase with auxilary switch block 415 volts suitable for 15 kVAR including testing connecting commissioning including taking down of old capacitor any type/capacity complete all as specified and directed.

Supply & fix power capacitor heavy duty contactor 3 phase with auxilary switch block 415 volts suitable for 33.5 kVAR including testing connecting commissioning including taking down of old capacitor any type/capacity complete all as specified and directed.

S&F Analogue Ammeter in replacement for measuring alternating current of range : 0 - 200 A flush type 96x96MM size complete all as specified and directed.

S&F Analogue Voltmeter in replacement for measuring alternating current voltage of range : Range 0-500 V flush type 96x96MM size complete all as specified and directed.

S&F in replacement indoor resin cast ring type current transformer of ratio 200/5 Amps, accuracy - 15VA, Class - 1. complete all as specified and directed.

M & L for sheet metal work for repair to electric panel doors, bus bar cover and accessories mounting supports for alignment with front door with 2/3 mm thick MS sheet duly painted with super enameled paint over one coat of red oxide primer including necessary cutting, welding and fixing in repairs complete all as specified and directed.

S&F in replacement MCB SPN, 10kA, 6-32 AMPS complete all as specified and directed.

S&F in replacement MCB TP, 10kA, 40-63 AMPS complete all as specified and directed.

S&F in replacement MCB SP, 10kA, 6-32 AMPS complete all as specified and directed.

S&F in replacement Rotary Type A/M Switch, 1 Pole, 2 Way with Off, complete all as specified and directed.

S&F in replacement Flush head Push Button Green/Red colour with 1 NC Block, complete all as specified and directed.

S&F in replacement LED indicator - R/Y/B/G 240 V AC. complete all as specified and directed.

S & F power contractor 3 pole , type ML-2 with 2 No + 2NC aux contacts with standard coil voltage 240 volts, rating 32 amp including testing, commisioning fixed in repairs complete all as specified and directed.

S & F power contractor 3 pole , type ML-3 with 2 No + 2NC aux contacts with standard coil voltage 240 volts, rating 40 amp including testing, commisioning fixed in repairs complete all as specified and directed.

S & F power contractor 3 pole , type ML-4 with 2 No + 2NC aux contacts with standard coil voltage 240 volts, rating 70 amp including testing, commisioning fixed in repairs complete all as specified and directed.

S & F power contractor 3 pole , type MNX 25, Size fr 2,AC3 rating (25 amp) including testing, commisioning fixed in repairs complete all as specified and directed.

S & F power contractor 3 pole , type MNX 40, Size fr 2,AC3 rating (40 amp) including testing, commisioning fixed in repairs complete all as specified and directed.

Disconnecting incoming and outgoing connections, taking out and overhauling of manually operated, draw out type air circuit breaker of any make 3 pole, 415 volts, AC, current rating 800-1600 A, including cleaning/ oiling/ greasing all mechanical moving parts, replacement of defective accessories, racking in and connecting incoming/ outgoing cables complete all as specified and directed. Note :Accessories required for replacement shall be measured & paid separately under respective item of this schedule.

Supply and fixing following accessories suitable for ACB of suitable make and capacity as per existing complete all as specified and directed.

Auxiliary contact

motor

Trip alarm contact

Under voltage release

Shunt realease

Insulation barrier

Earth fault release

Racking interlock

M&L for carrying out following work/repairs through manufacturer's authorised service engineer of voltage stabilizer of following capacities located at various tech Accn at Naval Station Karanja :- i) Opening of stabilizer at tech Accn workshop and taking out all defective / unserviceable parts, fixing of new parts after repair inplace of defective part, rewiring of defective control wiring etc and assembling complete all as specified & directed. ii) Testing of stabilizer after repair on existing load to give desired & rated output. iii) M & L for preparation of old painted surface by hand scrap and applying one coat of primer and two coats of synthetic enamel paint by spray painting. Note : - All defective parts including cable & oil to be replaced will be measured & paid separately under relevent item of schedule as supply only. However, cost of labour for fixing of new part is deemed to be included in unit rate Item above.

25 to 75 KVA capacity

100/125 KVA capacity

150 KVA capacity

200 KVA capacity

Supply only spares for voltage stabilizer of different capacitites of make as per existing complete all as specified & directed.

Synchronising motor low speed instant start, stop high torque input voltage 250V single phase 50HZ, 60 RPM type -of 3 Kg capacity

Synchronising motor low speed instant start, stop high torque input voltage 250V single phase 50HZ, 60 RPM type -of 10 Kg capacity

Voltage meter 0-500 Volts flush type square dial 96mm size

Control relay AC 230V, 250 OHMS, 1 pin with base plate.AC

Control relay 250 OHMS, 1 pin with base plate, 12V DC.

Control relay 230V, 250 OHMS, 1 pin with base plate, 24V DC.

Control operational switch 10 Amps capacity.

Control transformer/relay 24Volt DC.

Toggle switch 10Amps.

Indication lamp with bulb RYB.

Limit switch with aluminum housing.

Reset switch 10 Amps 230V AC.

Voltage increase/ decrease switch 10 A cap.

Aluminum hand wheel for manual operation.

Aluminum brush assembly for 200KVA stabilizer.

Aluminum brush assembly for 50/75/100/125/150 KVA stabilizer.

Terminal strip for 200 KVA stabilizer

terminal strip for 25/50/75/100/125/150 KVA /3x 16.6 KVA stabilizer

Variable voltage wound coil single phase for 200 KVA stabilizer

Variable voltage wound coil single phase for 50/75/100/125/150 Kva /3x 16.6 KVA stabilizer

Variable voltage wound coil single phase for 25 KVA stabilizer

Rectifier 15 Amp.

Insulator for dimmer.

Electrolytic capacitor 150mfd. 220V.

Electrolytic capacitor 1200mfd. 440V.

Carbon brush.

AC motor drive control cord.

Control PCB of control circuit of stabilizer 16.6 KVA to 500 KVA voltage stabilizer.

All as per BOQ item no. 93.31 but cut off PCB

Control transformer for 16.6 KVA to 500 KVA voltage stabilizer.

All as per BOQ item no. 93.33 but cut off control tranformer

S & F for set of LT tape with color coding red, yellow, blue & black complete all as specified & directed.

M.K Enterprises

SREE HARITHA ASSOCIATES