Renovation and Interior Fit-Out Works of SIDBI Office, Bhiwadi

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

1 FLOORING WORKS

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In

1.01 MR Natural Finish. Thickness 1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete with 120.00 metre 280.00 33,600.00

Rubber/ PVC Jointers and Gasket.

Supplying and fixing of 3mm Luxury vinyl flooring Top layer of approved design & Pattern as per

architects approval & Instructions

CARPET TILES: Providing and laying carpet tile flooring. Carpets shall be of Type 6 nylon loop pile

carpet tiles/Plank. The carpet shall have sufficient gauge (1/10 ~ 1/12) with sufficient stitches (10~13)

1.03 MR per inch. The carpet shall be solution dyed fibre content or with injection printing technology. The 15.00 sq m 1650.00 24,750.00

carpet shall have the pile height ranging from (2.0 ~ 3.0) mm with average density higher than

4500 Oz/ cubic yard. The total thickness of the carpet tile shall also range from (5.5 ~ 6.0) mm.

LAMINATED WOODEN FLOORING Providing and laying 8.3mm thick AC5 grade laminate wooden

flooring having good castor chair and furniture resistance strength. Plank dimension to be

1215x195x8.3mm with valinge clock locking system and wax coating for better sound resistance.

Impact and abrasion resistance to be of high grade having class EN 13329. The flooring shall be laid

1.04 MR with 2mm thick underlay and PVC sheet and prevent against moisture and foot taping sound. The 15.00 sq m 1770.00 26,550.00

item also includes the skirting and any other profiles required for proper installation.or its equivalent

specifications or as per the selection of client and items shall be complete in all respects. or its

equivalent specifications/ size as per the site requirement or as per the selection of client and items

shall be complete in all respects.

2 FALSE CEILING WORKS

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing

and fixing of frame work made of special sections, power pressed from M.S. sheets and

galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of

angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm

centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with

6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length

with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5

mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5

mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at

every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20

mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at

450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board

to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230

mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board

with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers

covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per

manufacturer's specification and also including the cost of making openings for light fittings,

grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per

drawings, specification and direction of the Engineer in Charge but excluding the cost of painting

12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS

certification marks)

Providing & fixing of Silhoutee Frame ceiling tile in size 600x600x15mm having noise reduction co-

efficient of 0.7, Density of 100 kg / m3, and Humidity resistance of 95% to be laid on exposed grid

system with white wrap comprising main runner 3.00 mm x 24mm web height cross tee 1.2 mtrs x 24

mm web height and 0.6 mtrs x 24 mm web height. The wall angle shall be 3.0 mtrs.

3 PARTITIONS AND WALL CLADDING

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

WALL PANELING :-Providing and fixing Paneling upto ceiling height consisting of Aluminium frame

and required board, frame work made of Aluminium section made of 50x25 mm , consisting of floor

and ceiling channel 50mm wide having equal flanges of 25 mm and 0.50 mm thick, fixed to the floor

and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50

mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm

wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within

flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6

mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with

3.1 MR suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre,

and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and

ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame

work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm

thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed

to the studs using metal to metal flat head screws, including jointing and finishing to a flush

finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm

x 0.5 mm), joint finisher as per manufacture's specification and direction of engineer in charge all

complete.(Cost of Aluminium framing 600X600mm Paid saperately)

Paneling with 11- 12 mm thick HDHMR board to IS: 5509 60.00 sq m 2,414.28 144856.86

WALL PARTITION-Providing and fixing partition upto ceiling height consisting of Aluminium frame

and required board, frame work made of Aluminium section made of 50x25 mm , consisting of floor

and ceiling channel 50mm wide having equal flanges of 25 mm and 0.50 mm thick, fixed to the floor

and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50

mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm

wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within

flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6

mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with

3.2 MR suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre,

and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and

ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame

work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm

thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed

to the studs using metal to metal flat head screws, including jointing and finishing to a flush

finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm

x 0.5 mm), joint finisher as per manufacture's specification and direction of engineer in charge all

complete.(Cost of Aluminium framing 600X600mm Paid saperately)

Both side 12 mm thick HDHMR board to IS: 5509 60.00 sq m 3450.00 207000

LAMINATE CLADDING- P/F 1mm thick laminate including 4 mm thick MDF, on an existing

Plywood surface.

Providing and fixing 12mm thick frameless toughened glass

door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot

3.4 21.18 & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for 35.00 sq m 5325.9 186406.50

fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock

and stopper etc. to be paid separately)

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought

3.5 9.1 framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length

(hold fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood 0.25 cum 142949.7 35737.43

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool conforming to

IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to

wall wirh screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete

as per directions of Engineer-in-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,

3.7 9.21 core of block board construction with frame of 1st class hard wood and well matched commercial 3

ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 12 sq m 2,392.65 28711.80

Providing and fixing aluminium extruded section body tubular type universal HS 3000 Slimline

Concealed Door Closer (having brand logo with ISi, IS : 3564,embossed on the body, door weight

upto 36 kg to 80 kg and door widthfrom 701 mm to 1000 mm), with double speed adjustment with

necessary accessories and screws etc. complete

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic

AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade, complete:

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor door stopper with

necessary screws, etc. complete.

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular Handle TH 123 with Roses

3.11 MR & Escutcheon in SS packaged with Mortice lockset 55mm backset, 20 SS forend, SS strike plate and 6 EACH 2,650.00 15,900.00

EP Cylinder for all flush doors.

Providing and fixing 600 mmx25 mm H Type handle for Doors approved make and designs as per

engineer in charge

Providing and fixing minimium 80-100 kg capacity flooor spring for Doors approved make and

designs as per engineer in charge

3.14 MR Providing and fixing Glass door lock approved make and designs as per engineer in charge 5 EACH 1,680.00 8,400.00

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to

prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile

3.16 13.83 Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture,

including applying additional coats wherever required to achieve even shade and colour.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile

Organic Compound ) content.

With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less

than 50 grams/ litre

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

BLINDS Providing & supplying of Window Blinds as per the approved sample in required shade

and style consisting, of ZEBRA BLINDS comprising of optima screen Fabric comprising of 22% polyester,

78% PVC, Fabric weight 460-480G weight per sq m, Thickness 0.67 mm, Yarn count 18- 19/cm,

having fire resistance standard – NFPA 701-89 small testing ISO- 5659-2 .Thetear resistance should be

complying to ISO4674 & breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick,

easy and safe installation, moulded plastic with steel spring support and inserted into the tube end. It

shall be driven by a ball chain pulley with ball chain and can be positioned at right side or left hand

side of the Shade. The Shade when lowering or raising, shall be automatically locked in position upon

release of the ball chain by means of a built in friction lock.Universal clutch for left and right hand

operation.Chain Gear Ratio of 1.75:1. The END PLUG shall be molded of plastic witha steel location

pin.The plug shall be inserted into the tube end.(Opposite to the Drive Unit) for ease of installation.

The SUPPORT BRACKETS shall be of coated steel & provided with covers and used in right hand or left

hand positions differentiated by the acceptance of the of the rectangular drive unit support or the

round idler plug pin.Can beinstalled (a) On Face (b) Ceiling Mount (c) On Frame

(d) in Recess. The Bracket should be protruding outside maximum of

80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm internal diameter & skin thickness

of 1mm and shall incorporate a key way integral with the tube to accommodate the spline. The

BOTTOM RAIL shall be a Flat Bottom made up of powder coated steel. The BALL CHAIN shall be 2mm

diameter cord with 4.5mm diameter acetal balls moulded co-axially to it on 6mm pitch to form an

endless ball chain. It is used for raising or

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface as approval of the

Architect. (Only film surface area shall be measured and paid).

Cabinet Shutters out of 19mm Commercial Plybaord finished in 1mm Laminate of matching,

Shutters to be fixed to a frame. Rigidly fixed on both sides and top finshed in laminate. No internal

3.20 MR carcass required. All Hinges of hettich or equivalent. Internal Surface of the shutter in balancing white 5 sq m 11,500.00 57500

laminate. All shutters to be provided with Stainless steel louvers at the top and bottom of the

shutter as per the site requirements and instrcution of the Engineer In charge.

Providing & fixing Sidbi Signages & Logo & Sidbi Enviremoent Theme as per Direction of Engineer in

3.22 MR Providing & fixing Sidbi Sign Glow Board For Exterior Acrylic Base Embeded Letter as per design 70 Sft 1350.00 94500

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height consisting of G.I.

frame and required board, including providing and fixing of frame work made of special

section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side

inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm

and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with

dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal

3.23 9.105 screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other

flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel

and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of

studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal

screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both

side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the

spacing of 300 mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to avoid through cracks,

M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each)

to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal

flat head screws, including jointing and finishing to a flush finish with recommended jointing

compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher

and two coats of primer suitable for board as per manufacture's specification and direction of

engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced

Gypsum (GRG) plaster board conforming to IS: 2095:

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR TOTAL TOTAL

E&M AMOUNT AMOUNT

DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor single

core cable in surface / recessed medium class PVC conduit, with

A.1 modular switch, modular plate, suitable GI box and earthing the

point with 1.5 sq.mm. FRLS PVC insulated copper conductor single

core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell

point (without independent switch etc.) with 1.5 sq.mm FRLS PVC

1.55 insulated copper conductor single core cable in surface / recessed

A.2 PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC

insulated copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed medium

class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated

copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the

1.24 existing modular plate & switch box including connections but

excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 30 122.00 3660.00

1.24.5 6 pin 15/16 amp socket outlet Each 20 197.00 3940.00

Digitally signed by AMIT

DSR TOTAL TOTAL

E&M AMOUNT AMOUNT

DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR)

Supplying and fixing modular blanking plate on the existing

modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/module, GI box along with

1.27 Modular base & cover plate on

existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the

1.14 following sizes of FR PVC insulated copper conductor, single core

cable in surface/ recessed medium class PVC conduit as required

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 250 275.00 68750.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 40 439.00 17560.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 40 1365.00 54600.00

Supplying and making end termination with brass compression gland

and aluminium lugs for following size of PVC insulated and PVC

sheathed / XLPE aluminium conductor cable of 1.1 KV grade as

Digitally signed by AMIT

DSR TOTAL TOTAL

E&M AMOUNT AMOUNT

DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR)

Supply of following XPLE armourned 1.1 KV grade conforming to

I.S.7098/1554Aluminium Conductor Cables :

MR Supply of following sizes of PVC sheathed PVC/XLPE insulated

C.2 Aluminium conductor armoured cable of 1.1 KV grade conforming to

IS:7098 part-1/ IS:1554 part-1 respectively & ISI marked.

(b) 3.5 C x 95 Sqmm XLPE cable RM 30 864.00 25920.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 30 378.00 11340.00

Supply of following sizes of copper cables -PVC sheathed

PVC/XLPE insulated Copper conductor armoured cable of 1.1 KV

grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively &

(a) 4 C x 16 Sqmm XLPE copper cable RM 40 1446.00 57840.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 15 2253.00 33795.00

Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C"

curve, miniature circuit breaker suitable for inductive load of

D.2 following poles in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

2.10.1 Single pole Each 40 256.00 10240.00

Supplying and fixing following rating, four pole, 415 volts, isolator in

2.13 the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Digitally signed by AMIT

DSR TOTAL TOTAL

E&M AMOUNT AMOUNT

DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR)

Supplying and fixing following way, horizontal type three pole and

neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess,

complete with tinned copper bus bar, neutral bus bar, earth bar, din

bar, interconnections, powder painted including earthing etc. as

D.4 required. (But

without MCB/ RCCB/ Isolator)

MR 12 way (4 + 36), Double door Each 1 9081.00 9081.00

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid

copper conductor PE insulated, shielded with fine tinned copper

braid and protected with PVC sheath in the exisitng

surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong

1.21 with accessories in surface/ recess including cutting the wall and

E.12 making good the same incase of recessed conduit as required

Supplying and Installation of following size perforated of painting

with powder coating M.S. cable trays of perforation of not more

E.13 4.1 than 17.5% in convinient sections, joined with connectors

suspended from the cieling with MS suspenders including bolts and nuts

painting suspenders etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 10 1137.00 11370.00

Digitally signed by AMIT

DSR TOTAL TOTAL

E&M AMOUNT AMOUNT

DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick

including accessories, and providing masonry enclosure with cover

plate having locking arrangement and watering pipe of 2.7 metre

long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in

recess for connections etc. As required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. As required.

Supply, Installation, Testing and Commissiong of 10 KVA True Online

Double Conversion UPS 3Phase Input - 3Phase Output in IGBT Based

Rectifier and IGBT Based Inverter Batteries:12 V, SMF Amararaja/Exide

with minimum VAH capacity of 15600 suitable for 30 minutes backup

with each ups Along with Accessories Rack, Interlinks, SFU, Parallel Kit, Nos 1 365000.00 365000.00

DC Cable Upto 5 Meters complete in all respect as per the directions of

the engineer in charge. UPS should have availability of Input /Output

isolator, Inbuilt manual bypass along with phase sequence corrector.

UPS Efficiency shall not be less than 94% from 25% to 100% Load

Total of Electrical items 518644.00 502976.00

Digitally signed by AMIT

VRF/VRV OUTDOOR UNIT

1.0 Description Unit Quantity Rate DSR Amount NDSR Amount

Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant

Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating

having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s) ,minimum

two compressors (with individual separate PCB) for above 14HP modules, microprocessor

based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or

equivalent, vibration Isolators with suitable foundation etc. complete as required. To

have better efficiency condenser fan shall be capable to operate at different

speed with respect to load. The unit shall deliver the rated capacity and in

confirmation as per IS 18728: 2024 and CPWD Specifications and work even at 50°C

ambient temperature without tripping. The system shall be able to deliver 100% of the

7.3 rated capacity upto 39 Degree Celcius.The unit shall be suitable to work on 400V +/-

10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled

with first charge of the refrigerant and ready for use as required. The condenser

should be coated with a hydrophilic film to prevent water accumulation on the surface of

the heat exchanger, enhance water dispersion, and reduce the risk of

degradation, thereby improving overall performance and durability. The Indian

Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy

Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as

per CPWD specification, connections, inter connections etc. as required. (For capacity

<40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super

ECSBC Building)

2.0 INDOOR UNIT

Supply, Installation, Testing and Commissioning of following minimum capacity 4 way

Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-

filter, fan section with low noise fan / dynamically balanced blower, multispeed

motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain

pump, grill, necessary supports, vibration Isolation, Corded remote control etc.,

7.4 suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as

required. The Indoor units must shut down upon receiving a singal from the BMS

System/Fire Signals. The system shall be capable to adjust air flow as per room

requirement in auto mode. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as

Digitally signed by AMIT

1.0 Description Unit Quantity Rate DSR Amount NDSR Amount

Supply, Installation, Testing and Commissioning of following minimum capacity High wall

type Indoor unit equipped with and comfort washable synthetic media pre-filter, fan

section with low noise fan/dynamically balanced blower, multispeed motor, coil section

with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control,

drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single

phase AC supply, complete as required. The Indoor units must shut down upon receiving a

singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as

per room requirement automatically. The cooling capacity of indoor unit will be at air

inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be

same as of Outdoor)

REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen

testing of following nominal sizes of soft/hard drawn copper refrigerant piping

for VRV/VRF system, complete with fittings, with suitable adjustable ring type

3 7.14 hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O

tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves

sections of 19 mm thick insulation as given below for Suction and Liquid lines, all

accessories as per specifications etc. as required :

3.2 7.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 40.00 346.00 13,840.00

3.4 7.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 25.00 615.00 15,375.00

3.5 7.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 15.00 739.00 11,085.00

3.8 7.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 30.00 1,157.00 34,710.00

3.10 7.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 30.00 1,286.00 38,580.00

3.14 7.13.2 Outdoor Multi Units Each 1 8098 8,098.00

5 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC Pipe ,complete with fittings,

supports,U trap arrangement,Clean Plug with 6mm nitrile insulation and accessories as

per specifications, drawings.

Providing and fixing control cum transmission wiring of 2 core x 1.0 sq. mm copper in suitable

conduits between indoor and outdoor unit.

Digitally signed by AMIT

1.0 Description Unit Quantity Rate DSR Amount NDSR Amount

6 MR Supply & Fixing IP55 Base Outdoor MCB Box with in 1 Nos 65 amp RCCB Nos 1 14650 14,650.00

7 MR Supply and Fixing MS Base Frame for VRV Outdoor Stand as per requirement of Size L.S 1 20500 20500

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - DATA and VOICE WORKS

S NO Description UOM Qty Rate DSR Amount NDSR Amount

A. UTP Components for Data

Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper

(DSR conductors for Connectivity of Hub room to End Point.High Speed

1.53.1) Gigabit Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable

4 MR termination at Rack Side. Keystone Unshielded Outlet, 180DG C6, Blue Nos. 36 359.00

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable

5 MR termination at Rack Side end Redantant . Keystone Unshielded Outlet, Nos. 36 359.00

180DG C6, Yellow 12924

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7

feet) for information outlet (I/O) to end user Redantant device

8 MR connectivity.High Speed Gigabit 24AWG U/UTP Patch Cord Yellow, LSZH, Nos. 40 420.00

C6, 2M (Yellow)

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7

feet) for information outlet (I/O) to Rack End Redantant device

9 MR connectivity.High Speed Gigabit 24AWG U/UTP Patch Cord Yellow, LSZH, Nos. 40 420.00

C6, 2M (Yellow)

Supply , Installtion , Testing and Comissioning of 24 port Loaded Angled

11 MR Staggred Jack Panel for CAT6 cable termination at rack end. Data Nos. 3 6500.00

Active Redandant 19500

SITC of 04 core OM3 Multimode fiber orange color 50/125, minimum

bending radius 15x OD 11458.33

13 MR SITC of 24U Rack Each 1 34,500.00 34500

Supply instllation testing and commissioning of Access Switch of 24 x 1G POE+, 4 x

SFP+ , 370W PoE, Switching Capacity of switch is of 176 Gbps having Forwarding

14 MR performance (64-byte packet size): 130 Mpps, Secure Shell (SSH), as per approved Nos. 1 165500

B 200 Pair MDF Box

1 MR 200 Pair MDF Box with mounting Frame Nos. 1 11666.00 11666

2 MR 10 Pair Krone Module Nos. 1 900.00 900

3 MR 25 Pair Riser Cable Mtr. 25 750.00 18750

GRAND TOTAL (A+B) 102600.00 321722.33

GRAND TOTAL (A+B) 102600.00 321722.33

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S No 2022/ DESCRIPTION QTY UNIT RATE TOTAL AMOUNT

S No 2022/ DESCRIPTION QTY UNIT RATE TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS

3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets

etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with

1 two or more coats of synthetic enamel paint of required shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of

2 rating 68 degree centigrade with required accessories :

18.21.1 Pendant type 18 Each 522.00 9396.00

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless

steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test

18.25 pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head

(Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket,

stockbar of following sizes complete as required.

Providing and fixing ISI Marked of approved make Fire Extinguishers complete with

all accessories as per manufacturer's specifications.

a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). 1 NOS 12070.00 12070.00

b) Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683). 2 NOS 2740.00 5480.00

ABC dry powder stored pressure type 6 kg capacity

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - CCTV

DESCRIPTION UNIT Qty RATE

Supply, Installation, Testing & Commissioning of 2MP IR IP H.265 Vandal Proof

Dome camera with 2.8 to 12mm Motorised Lens,Smart IR, up to 30M IR

distance,Up to 120 dB WDR (Wide Dynamic Range),3D DNR (Digital Noise

Reduction),H.265+, H.265, H.264, MJPEG,Corridor mode, Triple streams,3-Axis,

IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0 Lux with IR,Video

Compression H.265+, H.265, H.264, MJPEG,Behavior Detection Intrusion,

Supply, installation testing and commissioning of Network Video recorder

Linux based to manage and control all the cameras from control room.

2 MR Software shall support maximum 16 channel with joystick controller. Nos 1 34500.00 34500.00

256Mbps Bit Rate Input Max(up to 32-ch IP video), 2 SATA Interfaces, alarm I/O:

16/4, 1.5U case,19" with 1x4TB i.e. 4TB HDD inside

Supply Installation Testing & Commissioning of 32 inch Full HD LED monitor

including wall mount brackets/ clamps/ desk mounting stand.

4 MR SITC of HDMI cables 10 meters M2M etc all compelte. Nos 1 3500.00 3500.00

Total : A - CCTV 99700.00

Digitally signed by AMIT

FIRE ALARM SYSTEM

S.NO. DESCRIPTION Qty UNIT RATE

NO. Amount AMOUNT

INTELLIGENT FIRE ALARM SYSTEM

Supplying, installation, testing & commissioning of

FIRE PANEL upto 2 zone complete as required.

Supplying, installation, testing & commissioning of smoke detector with

c) 17.1.2 built in LED and Mounting base complete withb all Connections etc. as 22.00 No. 1153.00 25366.00

Supplying, installation, testing & commissioning of manual call boxes of MS

17.1.3 construction in Surface/Recess with Stainless Steel chain & hammer 2.00 No. 474.00 948.00

Assembly complete with glass and push button etc. as Required.

Supplying, installation, testing & commissioning of response indicator on

d) 17.1.5 surface/recessed MS Box having two LED, metallic cover complete with all 20.00 No. 196.00 3920.00

connections etc as required.

Supplying, installation, testing & commissioning of Fire alarm Sounder with

Facility to make annoucement, mountedc in M.S Box (16 SWG) with

Hinged cover plate & Suitable for operation with Amplifier i/c line

matching transformer etc complete as required .

CABLING & WIRING

Supplying & laying of 2x1.5 sqmm fire survival alarm armoured cable,

a) 17.5.2 600/1000V rated with annealed copper conductor having XLPE insulation, 240.00 Metre 173.00 41520.00

steel wire armouring & ERLS outer sheath complete as required.

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter &

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle board. Provision

of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site requirement.Main

Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)900mm X (D)

Supplying and placing in position of Back Storage as per photograph/drawing .The back storage shall be

made out of 25mm thick pre -laminated particle board of approved shade. The working and non working

2 Back Storage Nos 1.00 29,500 29,500.00

edges shall be finished with machine pressed with 2mm PVC egdge banding. Back Storage Dimension

Supplying and placing in position of 360 degrees revolving high back chair . The chair of Size :-

(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

3 with leatheritte and cut foam. The chrome plated loop armrest with padded upholstery is provided for Nos 1.00 15,000 15,000.00

extra comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of

10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/

2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X

(H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium Leatherette,

DGM Visitor Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever,

Back Chair Base:Cantilever Frame, Base Type: Cantilever, Maximum Seating Height:19".The Seat & back are made

up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam

of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the soft

cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour & Colour Family:as per

requirement, Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern,

Texture:Two Tone. steam beech solid wood have used for framing construction of sofa .The seat

cushion is made of multi layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 1.75

inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The

backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater

Dimension(L)1390mm X (D)750mm X (H)710mm

Reception Supplying, and placing in position of Cofee/ Corner Table as per approved design Dimension(L)450mm

Corner/ Cofee X (D)450mm X (H)450mm

Supplying, and placing in position of Centre Table as per approved design Dimension(L) 900mm X

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge

AGM/Manager banding. The table shall be provisioned with Side unit of overall size: 1500mm(L) x 450mm(D) x

Table 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter &

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle board. Provision

of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site requirement.

Main Table Dimension (L)1500mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)900mm

Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x

490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof plywood

and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood (IS grade - 303)

upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be provided with self

9 AGM Chair tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/- Nos 5.00 10,500 52,500.00

0.3 cm .The black .The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall

be operated at 30kgs extension force.The Seat & back are made up of 12mm thk hot pressed plywood

upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The

backrest has a foam of 28kg/m3. adjustable arm rest and head rest

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-

(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

Medium Back lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

10 chair AGM with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which shall Nos 10.00 8,500 85,000.00

Cabin have stroke of 10.0 +/-

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg /m3)

The backrest has a foam of 28kg/m3.

Supplying and placing in position of conference table of required size as per image/drawing. The work

surface top should be of thickness 42mm top prelaminated particle board with 2mm thick PVC edge

Conference banding. The side panel are made up of 36mm thick prelaminated particle & modesty panel are made

Table out of 25mm thick prelaminated particle board with 2mm thick PVC edge banding. The wire carrier

should be made from 0.6mm thick CRCA & powder coated 40-50 microns. Also having a provision of 6

module flip top box & metal raceway for wire flow.

Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x

490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof plywood

and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood (IS grade - 303)

upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be provided with self

12 tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/- Nos 1.00 10,500 10,500.00

0.3 cm .The black .The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall

be operated at 30kgs extension force.The Seat & back are made up of 12mm thk hot pressed plywood

upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The

backrest has a foam of 28kg/m3. adjustable arm rest and head rest

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-

(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

Medium Back lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

13 chair Confrence with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which shall Nos 6.00 8,500 51,000.00

room have stroke of 10.0 +/-

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg /m3)

The backrest has a foam of 28kg/m3.

Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) Supplying, and placing in position of linear

workstation as per Image.The worktop made out of 25mm thk. Prelam Particle board with 2 mm thk

PVC edge banding.The Table top supported on Mild Steel of size 50mm x50mm Slanted Leg and 50mm x

25mm Horizontal connectors with Powder coting of 50 Micron.Middle Leg :- 0.8 mm thk Metal panel

fixed on both side of the "T" leg for Vertical wire carrying purpose.(Sharing Workstation). 0.8 mm thk

Single/Double metal powder coated raceway with Powder coting of 50 Micron below top for

Linear wiring.Vertical wire carrying pole with powder coating 50 micron below top for wiring( Non- sharing

Workstation workstation ). Also having a provision of ms perfoated sheet hanging modesty. provision of glass divider

rest on the "D" brackets on the table top between opposite seatings. All working or non working edges

shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot

temperature. Provision of pullout PVC keyboard tray and CPU trolley for each seating.

Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of 2

drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated

Particle board with provision of handles & Locking arrangement

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-

Medium Back (W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

chair lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

15 Workstation/ with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which shall Nos 7.00 8,500 59,500.00

Reception/ have stroke of 10.0 +/-

Meeting room 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg /m3)

The backrest has a foam of 28kg/m3.

Providing & Installation of Pantry table of size 1.2m x 0.75m x 1.05m (ht) made out of 19mm thk.

Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per design. The

16 Pantry Table Nos 1.00 26,500 26,500.00

Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Providing & Installation of Reception table of size 1.8m x 0.75m x .9 m (ht) made out of 19mm thk.

Reception Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per design. The

Table Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

18 Pantry chairs Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC Nos 4.00 4,500 18,000.00

The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is made

Openable of 09mm thick MDF of approved shade. All the edges of storage surface shall be provided with machine

Shutter storage pressed imported PVC lipping glued with hot melt EVA glue free from any VOC with free groove handle

and suitable lock. All exposed area PVC edge lipping

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Pantry Under Pantry Under Counter Storage, made with HDHMR board finished with laminate on all exposed surfaces.

20.0 Counter Unit depth: 600mm. All edges shall be finished with matching edge banding. Includes shutters, shelves, Sqm 12500.00 6 75,000.00

Storage hardware (hinges, handles), and necessary fittings complete in all respects.

Pantry/ Pantry Overhead Storage Unit, made from HDHMR board of approved shade and grade conforming to E1

Workstation norms, with unit depth of 450mm. All exposed edges finished with 2mm PVC edge banding using

Overhead hotmelt EVA glue. Includes shutters, shelves, and necessary hardware and fittings, complete in all

Storage respects.

Total Amount 14,72,550.00

Total Amount 14,72,550.00

Digitally signed by AMIT

Sl. No. Description Unit Qty. Rate Amount

LED Down lighter (COB Type) (System lumen efficacy ≥ 105 <120lm/Watt) Supplying of LED Recessed/ surface Down lighter

(Round/ square/ Rectangular) COB Type of following body material and construction as per IS : 10322 with driver as per the

requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -15

deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P.

F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED,Driver &

electrical circuitary), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends , CCT 3000°K

/ 4000°K / 5700°K / 6000°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power

4221 consumption should not more than the specified rating and Fixture shall be confirming to relevant BIS standards and Nos 40 566.00 22640

trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete

in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing

etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 and <120 lm/Watt output . LM79 & LM80

Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall

be as approved by Engineer-in-Charge as per requirement.

(Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C)

Powder coated die cast /Extruded aluminium Body including trim with Aluminium Reflector 12 -15 watt

LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt) Supplying of Panel light 2x2 ft., of following body material

and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-

270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with

Short & Open circuit protection,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker

should be below 5 %), life time (LED,Driver & electrical circuitary), of minimum 50000 Burning Hours with , 70% of initial

Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(S tandard

Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be

of relevant BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen

printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor

single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt

output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted.

Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of

aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded

aluminium Body (Thickness > 1.20 mm)

Total of Electrical items 98240.00

Digitally signed by AMIT