PROVN OF 2 X TOILET BLOCKS BEHIND THE OR LINE OF ENGR REGT AT NASIRABAD

Amount

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in any type of soil complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2, with 40 mm graded stone aggregate as in foundation and mass concrete complete all as specified and directed.

M&L for brick work with fly ash old size brick, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with fly ash old size brick, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M & L for broken stone boulders Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L for 75 mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

Returning, filling in, including spreading levelling watering and well ramming in layer not exc. 25cm thick complete all as specified and directed.

Earth filling under floor including spreading levelling watering and well ramming in layers n exc 25 cm thick complete all as specified and directed

Removel of surplus soil to a distance n exc 50m and depositing where directed at a level n exc 1.5m above from the starting point complete all as specified and directed.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge

M & L for mild steel TMT bars 5mm dia and over upto including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for RCC M-25 grade (design mix) using 20mm graded aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and beams, sides and soffits (if any) of foundation and plinth beams , and similar work, vertical or to batter, flat surfaces of concrete , surface is required to be fair finished complete all as specified and as directed by the Engineer-in-Charge

M & L for M-25 grade (design mix) using 20mm graded aggregates as in columns, pillars, piers, posts and struts complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions, rectangular or polygonal surfaces of concrete , surface is required to be fair finished. complete all as specified and as directed by the Engineer-in-Charge.

M & L for RCC M-25 (design mix) using 20mm graded aggregates as in roof beams, lintel beams/bands, cantilevers, bressummers, lintels over 1.5m span, chajjas etc complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to sides and soffits of floor or roof beams, soffits of lintel beams/ bands, chajjas, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports overhangs etc, also splays between floors and beams, etc., flat surfaces of concrete ,surface is required to be fair finished. complete all as specified and as directed by the Engineer-in-Charge

M & L for RCC M-25 (design mix) using 20mm graded aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), flat surfaces of concrete , surface is required to be fair finished. complete all as specified and as directed by the Engineer-in-Charge

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, as roughed finished surface of concrete complete all as specified and as directed.

M & L for rendering 15mm thick in CM 1:4 (mixed with water proofing compound) on brick masonry (external) surfaces finished fair and smooth (without using exta cement), complete all as specified and directed. Note :- WPC will be measured and paid separately.

M & L for rough cast plaster mix with crusted stone (6-10 mm), sand and cement in the ratio 1:1:1 , over 15mm thick rendering in CM 1:4 as in under coat including dubbing coat (if required) complete all as specified and directed.

M & L for rendering 10mm thick in cement plaster 1:6 on fair faces of brick work or concrete surfaces even & smooth without using extra cement complete all as specified and directed

M&L for rendering 10 mm thick in cement plaster 1:4 as in ceiling surfaces finished fair and even complete all as specified & directed.

M & L for preparation of newly plastered surfaces of Ceiling & applying three coat of white wash complete all as specified and directed

M & L for preparation of newly plastered surfaces of walls & applying three coat of white wash complete all as specified and directed

M&L for preparation of new plastered surfaces and applying two coats of cement base paint over a coat of primer on wall surfaces complete all as specified and directed.

S&F vitreous China "Orissa pattern" size 580 x 440mm" white colour, with intergral foot rests with vitreous china 'P' or 'S' trap front or back inlet including connection to trap and to flushing pipe, anti syphnage pipe and making good the floor to match the existing complete all as specified and directed.

S & F vitreous china wash down water closet pan EWC (pedestal pattern) white including fixing bolts & seat cover etc but excluding flushing cistern and flush pipe complete all as specified and directed

S&F Toilet paper holder with flat recessed type stainless steel complete all as specified & directed.

S&F health faucet cast copper alloy chromium plated with flexible chrome hose and wall hooks complete. Make:- Jaguar ALD-CHR 573 or parryware T9941A1

S&F PVC valve less syphonic action type, low level flushing cistern, 10 Ltrs capacity . White, with inlet ball valve, float and handle & flush pipe, fixed on walls by drilling holes and using PVC rawl plug of suitable size complete all as specified and directed.

S&F 15mm bore , 450mm long PVC connection with PTMT nuts complete all as specified and directed.

S&F chromium plated 15mm bore stop/angle valves, ISI marked, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed by Engineer-in-charge.

S&F in Soap dish, fixed to plugs with chromium plated brass screws embedded in the wall complete all as sped & directed.

M&L for 20 mm thick Granite work (table rubbed and polished) in steps, jambs, pillars, window cills, WHB platform and like over 15 mm thick in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with sahde of granite complete specified and directed.

S&F vitreous china white wash basins, including waste pipe, brackets, and connecting pipe complete all as specified and directed. Make :- Jaquar KUS WHT 35901Table top basin Kerovit Mazer KB1086 or equivalent amke and model s approved by AO.

S&F 15mm bore brass CP mixer for mixing hot & cold water for wash basin or bathroom screwed down for iron pipe and fixed complete all as specified.

S & F of vitreous China urinal, flat back, half stall type white/ ivory colour with grating and Union for discharge pipe. Including connection to flushing pipe and outgoing waste pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F curved shaped 8mm thick frosted glass urinal partition of size 900x 450mm including necessary SS clamp and bottom support to fixed on wall and floor complete as specified. Make Jaguar JSE-CHR-810UC 450X

S&F Chromium plated ISI marked bib taps, with capstan heads, screwed down for iron pipe or for brass ferrule & fixed for 15 mm bore pipe complete all as specified & directed.

S&F Toilet fitting Two way bib cock 15 mm bore complete all as specified & directed. Make:- Jaguar Cat No. OPP-CHR-15041PM

S&F tubular towel rail brass chromium plated 20mm dia 'D' type 60cm long between flanges complete all as sped & directed.

S & F brass chromium plated swivel shower rose 125mm size, including fixing to steel pipe or union complete all as specified and as directed by the Engineer-in-Charge.

S&F 15mm bore, angle valve/stop cock, long shank & cup (concealed type) cast copper alloy, fancy type chromium plated with screwed down light pressure with crutch or butterfly handle, screwed both ends for iron pipes complete all as specified and directed by engr in charge.

M & L for Non-skid Ceramic coloured tiles 7 to 8 mm thick ( square /Rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured in white or coloured cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6), over 25 mm thick PCC type 1:2:4 type B-0 using 12.5mm graded stone, complete all as specified and directed.

M&L for glazed ceramic coloured tiles 7 to 8mm thick, area of tile exc 0.11 sqm but n.exc 0.18 sqm, on vertical surfaces of wall such as skirting/ dados ect set and jonted in neat cement slurry and pointed in white cement to match the shade the tiles over and including 10mm thick screed plaster on stone/brick masonry walls in CM 1:4 complete all as specified and directed.

S&F Steel window/ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including two caots of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge

S & F factory made solid PVC moulded door shutter of approved colour with particle board core, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, fixing in frame at site as per specification & drawing on SSR Part -II 2020 complete all as specified and as directed by the Engineer-in-Charge

S & F IInd Class HW 35mm thick glazed and skeleton factory made shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) supplied and fitted to chowkats.

S&F stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as specified and directed.

S&F 3mm thick figured glass, pin head type and glazing with oil putty in square n. exc 0.50 Sqm in each pane, complete all as specified and directed.

S & F 300mm, ordinary rat tail rod pattern springs including roller and roller plate omplete all as specified and as directed by the Engineer-in-Charge

S & F 300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed by the Engineer-in-Charge

S&F for aluminium anodised barrel tower bolt 150mm long of extruded section complete all as specified and directed.

S&F for aluminium anodised handle 150mm long fabricated type complete all as specified and directed.

S&F aluminium butt hinges ISI marked of size 100mm ISI marked complete all as specified and directed.

M & L for rolled mild steel work frame work as in doors or gates, staging for tank, angle or other section with gusset plates , rails, braces, etc complete drilled for fixing and confirming to Fe-410W (Gde E-250 quality 'A') complete all as specified and directed.

M&L for preparing the steel surfaces over 10 cm width or girth & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as specified and directed.

M & L for two coats of synthetic enamel paint over coat of pink primer on newly wooden surfaces of any description not otherwise described over 10 Cm width or girth including preparation of surfaces omplete all as specified and as directed by the Engineer-in-Charge

Supply only Integral water proofing compound complete all as specified and directed.

S&F PVC floor/nahani trap with grating 75mm dia fixed with lead joint complete all as specified and directed.

S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) , hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F water tubing 15mm bore, medium grade, ISI marked galvanised with all fittings & fixed to walls, ceiling or laid in floors complete all as specified and directed.

S&F water tubing 20mm bore, medium grade, ISI marked galvanised with all fittings & fixed to walls, ceiling, or laid in floors complete all as specified and directed.

S&F water tubing 25mm bore, medium grade, ISI marked galvanised with all fittings & fixed to walls, ceiling, or laid in floors complete all as specified and directed.

S&F ball valves PTMT with high pressure with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 25mm bore (min weight 210 gms) complete all as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints,fixed to walls including clamp, laid in trenches or in floors of bore 110mm.complete all as specified

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints,fixed to walls, laid in trenches or in floors of bore 75mm.complete all as specified

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal with access door with cement joint complete all as specified and directed.

S&F PVC (SWR) 75 mm bore bends with oval eccess door fixed with cement joint. complete all as specified

S&F PVC (SWR) 110 mm bore heel rest bend fixed with cement joint complete all as specified

S&F PVC (SWR) 110 mm bore Vent cowl complete all as specified

M&L for rendering 10mm thick in CM 1:4 mixed with water proofing compound @ 3% by weight of cement on fair faces of RCC/stone patti roof surfaces finished even & smooth without using extra cement complete all as specified and directed Note :- WPC will be measured and paid separately.

M & L for five layered roof treatment with APP modified polymeric water proofing membrane, 2mm thick having centre core not less than 100 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 2.60 Kg/ Sqm applied with bonding material using belown type bitumen conforming to IS-702 Grade 85/25 @ 1.20 Kg/ Sqm over bitumen primer conforming to IS- 3384 @ 0.40 Kg/ Sqm with final coat of bonding bitumen grade 85/25 @ 1.20 Kg/ Sqm over APP membrane with all overlaps complete all as specified and directed.

Material and labour for 40mm thick (average consolidated thickness) PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of 'V' shaped groove 6mm wide and 10mm deep at 1.20 metre interval or parts thereof, both ways on top of PCC padding and filled with mastic bitumen of (1:1) proportion complete all as specified and directed.

M&L for RCC NP-3 150mm dia in bore drain pipes laid in trenches and concrete bed to drain pipes of 150mm bore, including packing under, and haunching against the sides of pipes after they are laid and tested cement concrete 1:4:8 type D-2 complete all specified and directed

M&L for LLDPE Septic tank designed to carry sewage and sludge water, including excavation in any type of soil In PCC 1:4:8 below foundation ,vent shaft ,connection, etc., complete for 30 users, complete, all as specifie and directed..

M&L for construction of soakage wells, excavation in any type of soil, foundation in PCC 1:3:6, wells of noney combed and solid in M-25 Concrete, including intercepting chamber, screen chamber, brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete of size 2.4 M dia X 3.0M deep etc complete all as specified and shown in drg No. CEBZ/TD/78/2011, sheet 1 & 2 and as directed.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete

M&L for factory made 60mm thick machine pressed precast cement concrete coloured, reflective type interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 25 mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

M & L for 75mm thick cement concrete type D-2 1:4:8 using 40mm graded aggregate as in sub base of floor, complete all as specified and as directed by the Engineer-in-Charge.

M&L for precast cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in kerb stone setting in cement mortar 1:6, including necessary earth work excavation complete, all as directed.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for:-

One light point controlled by one, one way switch.

All as per item No. 85.00 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F switch piano flush type 5 amps, single pole one way 240 volts.

S&F switch piano flush type 15 amps, single pole one way 240 volts.

S&F socket out let 2 in 1 multipurpose, 3 pin, 5 and 15 Amp flush type complete.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm.

S & F LED tube light fitting retrofit batten in acrylic linear tube (1x18 watt), 230 V for single LED tube light including 1x18 W LED retrofit bar professional CW 6500 K cover channel, bipin holder, LED power driver, connector block, etc complete with all accessories internally prewired and incuding connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

Supply and fixing LED lamp 9/10 watt , 230 volts , 50 Hz, B-22 base for fixing in lamp holder and wall mounted decorative light fitting complete all as specified and directed.

S&F LED bulk head luminaire 1x 10 W bulk, IP 65 protection complete with all accessories and including connecting up with three core copper conductor cable complete all as specified and directed.

Supply and fixing testing and commissioning energy saving street light luminaire suitable for & including 35 watt LED , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete , IP 66 protection including connecting with three core copper flesible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge.

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single phase, 230V of size 300 mm sweep with blades and frame and louvers complete fixed and opening of wall with suitable MS bolts, grouted to wall and connecting up including provision of cable from connector to fan with flexible cable 24/0.2mm with copper conductor and necessary fitting arrangements complete all as specified and directed at site.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed.

S & F of MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 complete all as specified and directed.

S & F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB SP `C' series for geyser complete all as specified and directed

Contd.. Item No. 104.00 (c )Tank shall be insulated with 40 mm thermal grade PU insulation with FRP cladding , Tank stand assembly made of angle of size 38x38x4mm duly pretreated and stove enameled with black colour paint complete (d) Provision of electrical back up with minimum 4 KW heating element including providing one No 32 Amps MCB 10 KA rupturing capacity with Metal clad box and top complete (e) The Solar water heating system shall be provided on Platform on ground made out of PCC and 45 cm in height as per manufacturer direction (f) Heat exchanger shall be cage type and make of stainless steel tube of grade 04 Cr 18 NI of 07 18 NI of IS 1570 (Par-5) -1885 (g) All other pipe / civil work , connection work for PVC tank, as per OEM recommendation electrical work , outlet and inlet thermometer, Air release valve , check valves , gate valves controls and instruments etc all as required shall be deemed to be included in Unit rate quoted . System internal piping shall be ISI marked GI pipe medium class of IS:1239 duly insulated with 50 mm thick rock wool of 48 Kg / cum density and 26 SWG Aluminium cladding Notes :-1. The system shall be tested on completeion to ensure that 300 Ltrs (as specified) of water at 60 degree centigrade is available in hot water tank on a normal day in cold season.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F mild steel rolled sections as in main and cross beams, for dtaging of water tank fixed with angle cleats or other connecting plates etc. conforming to Grade E-250 quality `A’ all as specified and directed.

Supply and fixing tubes medium grade GI tubing 20 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection all as specified and directed.

Supply and fixing tubes medium grade GI tubing 25 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection all as specified and directed.

Supply and fixing tubes light medium grade GI tubing 40 mm dia with all fitting laid in trenches/fixed on wall/pole all as specified and directed.

S&F Stop valve gun-metal, glove or gate valves with iron wheel head, screwed both ends for GI pipes of size 20mm dia all as specified and directed.

S&F Stop valve gun-metal, glove or gate valves with iron wheel head, screwed both ends for GI pipes of size 25mm dia all as specified and directed.

S&F Stop valve gun-metal, glove or gate valves with iron wheel head, screwed both ends for GI pipes of size 50mm dia all as specified and directed.

Supply and laying including jointing, testing or fixing or passing through pipe, trench or duct commissioning and testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade size 16 sqmm, 2 core complete all as specified and directed by Engineer-in-Charge.

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly complete all as specified and directed by Engineer-in-Charge.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed.

JWALA ENTERPRISES

H M LAXMINARAIN

M/s AKASH CONSTRUCTION CO.

M/s SUNIL ENTERPRISES

PD GUPTA AND COMPANY

M/S SHIVA TRADERS

M/S AL ASMA ENTERPRISES

BSB CONSTRUCTION COMPANY