WBSAMB / CEO / 36 / 2025 - 26

Surface Dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed.

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm.

b) Depth of excavation for additional depth beyond 1,500 mm. and upto 3,000 mm. but not requiring shoring.

Pre-constructional Anti-termite measures (c) Anti-termite treatment to the top surface of the consolidated earth within plinth walls with chemical emulsion by admixing chloropyrefos emulsifiable concentrates (1% concentration) with water by weight @ 5 litres / sq.m of the surface before sand bed or sub-grade is laid. Holes upto 50mm to 75mm deep at 150mm centre to centre both ways shall be made with 12mm diameter mild steel rod on the surface to facilitate saturation of the soil with the chemical emulsion. The work shall be carried out as per specification described in 6.4 of code IS-6313 (Part-II) 1981. (Mode of measurement will be per sq.m of plan area of plinth treated).

Post-construction Anti-termite measures (a) Anti-termite treatment to the outside of foundation with chemical emulsion by admixing chloropyrefos emulsifiable concentrates (1% concentration) with water by weight including cutting shallow channel by excavating soil along and close to the wall face ensuring uniform dispersal of the chemical emulsion to a depth of 300mm from the ground level by rodding with 12mm dia. MS rod at 150mm interval in the channel. 1.75 litres of chemical emulsion per metre length shall be used and a balance quantity of 0.5 litres of the chemical emulsion per running metre shall then be used to treat the backfill earth by directing the spray of the emulsion towards the wall surface. The entire work is to be carried out as per specification laid down in para 4.3.1.1 of code IS-6313 (Part-III)-1981.

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

(I) Cement concrete with graded stone ballast (40 mm size excluding shuttering) 1:3:6 In Ground Floor (A) Pakur variety

Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches.

Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand (payment to be made on measurement of finished quantity)

Earthwork in filling in compound, tank, low land, ditches etc. With good earth, in layers not exceeding 150mm including breaking clods and consolidating the same by ramming and dressing complete. (Payment will be made on profile measurement before and after the work). (b) With carried earth arranged by the contractor within a radius exceeding 3 km. but not exceeding 5 km. including the cost of carried earth. b)with carried earth arrange by the contractor within radius of 3 km.including cost of carried earth.

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) (a) With earth obtained from excavation of foundation.

Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. In ground floor and foundation.[using concrete mixture] M 25 Grade, (i) Pakur Variety.

Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. Above Ground Floor.[using concrete mixture] M 25 Grade,(i) Pakur Variety

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor).c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work.Ground Floor.

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor).c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work. Above Ground Floor.

Reinforcement for reinforced concrete work in the all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection complete as per drawing and direction. i) For works in Foundation and upto roof of ground floor / upto 4M i) Tor steel/Mild Steel III.Other manufacturers not specified( PWD SOR 10th corrigenda & addenda)(2.00 % OF TOTAL VOLUME OF R.C.C WORK ) Sl. No.12

Reinforcement for reinforced concrete work in the all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection complete as per drawing and direction. Above Ground Floor. i) Tor steel/Mild Steel III.Other manufacturers not specified( PWD SOR 10th corrigenda & addenda)(1.80 % OF TOTAL VOLUME OF R.C.C WORK ) Sl. No.13

Brick work with 1st class bricks in cement mortar (1:6) .a) Foundation and plinth

Brick work with 1st class bricks in cement mortar (1:6) . b) In superstructure, ground floor.

Brick work with 1st class bricks in cement mortar (1:6) . Above Ground Floor.

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor.

125 mm. thick brick work with 1st class bricks in cement mortar (1:4). Above ground floor.

Labour for Chipping of concrete surface before taking up Plastering work.

Plaster (to wall, floor, ceiling etc) with sand and cement mortar including rounding off or chamfering corners as directed and racking out joints including throating, nosing and drip course, scaffolding / staging where necessary.Ground Floor: [Excluding cost of chipping over concrete surface] A) With 1:6 cement mortar, 20 mm thick Up to 4 meter from Plinth level

Plaster (to wall, floor, ceiling etc) with sand and cement mortar including rounding off or chamfering corners as directed and racking out joints including throating, nosing and drip course, scaffolding / staging where necessary. [Excluding cost of chipping over concrete surface] A) With 1:6 cement mortar, 20 mm thick. Above Ground Floor.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course,scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface].(2) With 1:6 Cement mortar.(a) 15 mm thick plaster ( External). (i) Ground Floor.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course,scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface].(2) With 1:6 Cement mortar.(a) 15 mm thick plaster ( External). Above Ground Floor.

Neat cement punning about 1.5 mm. thick in wall dado, window, sills, floor, drain, etc.

18mm to 22mm thick, kota stone slab set in 20mm thick (avg) cement mortar (1:4) in floor, stair & lobby including pointing in cement slurry with admixture of pigment matching the stone shade, including grinding & polishing as per direction of Engineer-in charge to match with the existing work. [Slurry for bedding @4.4kg/Sq.m and pointing @2.0kg/Sq.m].

Supplying, fitting and fixing 18mm. to 22mm. thick kota stone slab in wall,dado in 15mm thick [avg] cement mortar(1:3) including making suitable arrangement to hold the stone properly by brass/copper hooks including pointing in cement mortar (1:2) (1cement : 2marble dust) with admixture of pigments matching the stone shade, including grinding and polishing all complete as per direction of Engineer-in-charge including cost of materials, labour, scaffolding, staging, curing complete. [Using cement slurry for [email protected] kg/Sq.m and for jointing @1.8 kg/Sq.m]

(a) Supplying, fitting and fixing steel rolling shutter profile type with 18 B.G . of approved type steel latche section 75mm wide, fitted with coil wire spring to necessiate the fitting of required Nos. of C.I.Pulleys on heavy type solid drawn seamless steel tube complete with locking arrangements both inside and outside specially builtup side guide channels including providing a hood for the steel rolling shutter in the room, painting two coats of approved aluminium paint over a coat of red lead primer complete.

M.S. structural works with hollow sections ( square or rectangular shape) conforming to IS: 806-1957 & IS:1161-1958) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1956 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete. c) Span beyond 20 Mtr and up to 30 Mtr.

M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 Kg. / m. or 15 % of weight for finished structal members weighing less than 22.5 Kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of Engineer In Charge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the rate for each additional floor or 4m. beyond initiial 8m. or part thereof. I) For structural members of specified sections weighing less than 22.5 Kg./m.

Supplying , fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work). (i) In Roof:-

Supplying, fitting & fixing 1.5mm thick Trapezoidal profile corrugation Polycarbonate clear sheet made of national brand, excluding the supporting frame work, fitted and fixed with 10mm dia x 55mm Self-driving screws, EPDM washers and putty complete with 150mm end lap and one corrugation minimum side lap complete as per specification & direction of Engineer-in-charge including materials, labour, taxes and all other incidental charges (Payment to be made on area of finished work).

Supplying, Fitting corrugated Zinc Alluminium alloy coloured sheet ridging fitted with necessary bolts,screws,washer etc complete.(225 mm end lapping) (A) 300 mm lapping each way (a) with 0.60 mm sheet

Zinc Alluminum alloy colour coated steel sheet valley gutter with perimeter not less than 750 mm with 225 mm lap each way fitted and fixed with necessary bolt, nuts, screws, etc.complete.Valley gutter made of 0.63 mm.thick sheet. (300mm End Lapping)

Holding down bolt with nut including 100 x 100 x 6 mm plate washer at bottom fitted complete and packing the hole with cement concrete or cement grout as directed. (iii) 20 mm dia. (c) 450 mm long

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc..

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary .On Steel surface With super gloss (hi-gloss) - Two coats (with any shade except white)

Supplying fitting fixing Turbine Air Ventilator is made of good quality stainless steel TISCO made and neck dia 24 inch, Turbine dia 31 inch, Height 18 ince, Center Shaft 30 mm Ø SS outer jacket & 12 mm Ø SS shaft , Nett Weight 7.5 kg , Top plate-SS 430:1.00 mm,Base ring - SS 430:5 inch, No of Vanes & MOC-42 nos Vanes SS 430: 0.45 mm, Suction capacity- 1400 CFM @ 4m/sec wind including 2.5mm thick FRP/VYN mounting base plate(5 feet x 3 feet & weight 7.0 kg)) , Inner & Outer Arms MS with Electro Zinc plating.

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. In Ground Floor: (a) One Coat Quantity same as outside plastering work, Ground floor upto 4.0 Mtr from Plinth level subtracting neat cement area

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. : (a) One Coat. Above Ground Floor. Quantity same as outside plastering work, Ground floor above 4.0 Mtr from Plinth level

Protective and decorative acrylic exterior emulsion paint of approved quality as per manufacturers specification and as per EIC to be applied over acrylic primer as required. The rate includes cost of materials, labour, scaffolding and all incidental charges but excluding the cost of primer. In ground floor( two coats). a) Normal Acrylic Emulsion. Ground Floor. Quantity same as outside plastering work, Ground floor upto 4.0 Mtr from Plinth level subtracting neat cement area

Protective and decorative acrylic exterior emulsion paint of approved quality as per manufacturers specification and as per EIC to be applied over acrylic primer as required. The rate includes cost of materials, labour, scaffolding and all incidental charges but excluding the cost of primer. Two coats. a) Normal Acrylic Emulsion. Above Ground Floor. Quantity same as outside plastering work, Ground floor above 4.0 Mtr from Plinth level

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) (a) One Coat i) Water based interior grade Acrylic Primer

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface.Two Coats

Supplying, fitting & fixing UPVC pipes A - type and fittings conforming to IS: 13592 -1992 with all necessary clamps nails including making holes in walls, floor etc. and cutting trenches in any soil through masonry concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen / M. seal etc.) complete. For Rain water A) UPVC Pipes: (ii) 110 mm dia. For Rain water pipe

B) UPVC Fittings: c) Bend 87.5 degree (ii) 110 mm dia. For Rain water pipe

d) Shoe (ii) 110 mm dia. For Rain water pipe

Compacting original ground supporting subgrade Loosening of the ground upto a level of 300 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of Tables 300.1 and 300.2 for subgrade construction as per Clause 305.3.4 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).

Supplying , spreading and compacting Sand to required thickness, in layers not exceeding 150 mm to proper gradient and camber, inundating each layer by water and packing and ramming layer by layer to achieve desired compaction, including lighting, guarding, barricading and making adequate earthen bundh where necessary, curing with water as per direction, mending cracks and depressions by ramming wherever necessary.

Construction of Sub Base using Local Materials, spreading in uniform layers with Motor grader on prepared surface, including screening the metal as necessary, mixing by mix in place method with Rotavator at OMC, and compacting with vibratory roller to achieve the desired density, lighting, guarding and barricading including cost and carriage of all materials and making necessary earthen bundh of one metre wide on each side to protect the edges complete as per Clause 401 of Specifications for Road & Bridge Works of MoRT&H (5th Revision (i) For Construction of Sub Base by compacting 1st class brick aggregates (40mm down) and sand (in proportion of 60:40).

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening / binding materials to fill up the interstices of coarse aggregate, watering including lighting, guarding, barricading and making necessary earthen bundh of one metre width on each side and preparing the bed by necessary cutting or filling, including cost of all materials and hire and labour charges of all men and machinery and compacting to the required density, as per Clause 404 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). (i) Grading-I Aggregate (63 mm to 45 mm) Using Stone Screening Type A (13.2 mm) B. Manual Means..

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening / binding materials to fill up the interstices of coarse aggregate, watering including lighting, guarding, barricading and making necessary earthen bundh of one metre width on each side and preparing the bed by necessary cutting or filling, including cost of all materials and hire and labour charges of all men and machinery and compacting to the required density, as per Clause 404 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). (iii) Grading-II Aggregate (53 mm to 22.4 mm) Using Stone Screening Type B (11.2 mm) B. Manual Means.

Hire and labour charges for Shuttering with or without staging upto 4.0 m height using approved stout props with wooden planks/ply wood/steel sheet plate with required bracing for any kind of plain or reinforced concrete works in all sorts of minor structure including culvert, box culvert, crossdrain etc. The rate is inclusive of fitting, fixing and striking out after completion of work as per specification and direction. (b) Where staging is not required.

Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. Above Ground Floor.[using concrete mixture] M 25 Grade,(i) Pakur Variety

Bituminous filler of approved type in expansion joints of dummy joints including finishing the top surface as directed.

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. 3 mm. thick topping Using grey cement : (iii) 35 mm. thick.Ground Floor.

Electrical Work

Supply of 4 Core 16 Sq mm Alluminium XLPE /PVC Armoured cable.

Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed

Laying of cable upto 3/4 core 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting.

Fixing of Cable along the length of O.H. pole incl. S & F MS pole clamps fabricated from 25 mm x 6 mm MS flat incl. painting.

Laying only Cable upto 50 sqmm through existing RCC/Hume/ GI Pipe/open masonary trench for single, 2, 3, 3½ & 4 core.

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables of 4 core 16 sqmm

Finishing the end of 4 core 16 sqmm XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials

Supplying and fixing 415V 63 Amp Sheet steel Main Switches on angle iron frame on wall (Make: Havells or equivalent)

Supply of 11KV grade 4 core 10 sqmm Al armoured cable for main switch to Bus-bar.

Laying of cable upto 3/4 core 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting.

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables of 4 core 10 sqmm.

Finishing the end of 4 core 10 sqmm XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials

Supplying & fixing 4 bars 415 V, 100 A Busbar chambers (4x50x5mm) sheet metal (16 SWG) Iron Clad. Dimension of Sheet Metal Box 500x150mm Al. bars on angle iron frame on wall, incl.earthing attachment and painting as required – ( As per Drawing no. 470 of PWD Specification Book – May 1991)

Supplying and fixing double door Horizontal 6 way TPN MCB Distribution board for MCB Isolator incomer with IP-42/43 protection, on angle iron frame on wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment with Supplying and fixing 415 V 63 A Four Pole MCB Isolator of Breaking capacity 25kA/35kA with fixed thermal and fixed magnetic / adjustable thermal and fixed magnetic setting in existing DBs /Enclosure (DHDPTHODRW06) and necessary connection and Supplying and fixing 240 V 18 nos (6-32 )A SPMCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection.(Make- Havells or equivalent)

Distribution wiring in 1.1 KV single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in 20mm size PVC rigid conduit 'FR' (Precision make) incl. necy. fittings as required 2 x 56/0.3 (4 sqmm) + 1 x 36/0.3 (2.5 sqmm)[ TPN DB to SPN DB and AC point]

Supplying and fixing of (2+8) Way double-door SPN MCB Distribution Board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment with Supplying and fixing 240 V 40 A MCB Isolator on din rail of existing DBs and necessary connection.and Supplying and fixing 8 nos 240 V (6-16) A MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection.

Distribution wiring in 2 x 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in 20mm size PVC rigid conduit 'FR' (Precision make), with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board cum JB on wall complete with 2 no. suitable size “Ph & N” copper bar incl. bakelite/Perspex (wall matching color) top cover 3 mm thick and incl. 175mmx100mmx65mm inspection box, making earthing attachment, painting the MS box and mending good the damages to original finish. Average run 12 mtr.

Distribution wiring in 1.1 KV grade 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in 20mm size PVC rigid conduit 'FR' (Precision make), with 1.1 KV grade 1 x 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire as ECC, to 5A 3 pin flush type plug socket & Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board cum JB on wall incl. bakelite/Perspex (wall matching color) top cover 3 mm thick and incl. painting the MS box and mending good the damages to original finishOn Board.

Distribution wiring in 1.1 KV single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in 20mm size PVC rigid conduit 'FR' (Precision make) incl. necy. fittings as required 2 x 36/0.3 (2.5 sqmm) + 1 x 22/0.3 (1.5 sqmm) ECC

Supply & Fixing 240 V, 3 nos. 6A, & 1 no. 20A plug socket with separate 3 nos. 6 A & 1 no. 20A Piano key type switch, indicator & 20A switch type SP MCB (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F 240x200x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required

Supplying and fixing 415V, 32 Amp TPN SFU with sheet steel enclosure on flat iron/angle iron frame on wall with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating.Make- L&T

Supply of 40 Watt PHOTON ULTRA PLUS High efficacy wellglass which consumes lesser energy and maintains high lighting levels. Luminaire efficacy of 140Lm/Watt to reduce quantity/wattage thereby reducing operational cost. Ingress protection of IP66. Available in Clear PC. Model No. CIP-311-40-57-HL4-CP-NSG. Make- Crompton or equivalent.

Fixing only Floodlight Fitting with suitable tie clamps and MS plate for mounting on Pole/Tower or similar structure.

Supply of 18 Watt PROXIMA - S is a high performance low- height downlighter suited for any modern professional workspace. Robust PDC aluminum housing ensures long life. Available in 5700K, 4000K, 3000K CCT Efficacy 100LM/W, Model No. CDR-209-18-57-SL-NWH. Make- Crompton or equivalent

Fixing only bulk head ceiling fitting on wall /ceiling by screws etc.

Supply of 240V 300 mm(1400 RPM) heavy duty exhaust fan. Color-Grey) (Make: Orient / Equivalent )

Fixing only exhaust fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust of 300mm/12inch Dia.

Supply & Fixing of 30 cm Exhaust fan (12") louver shutter on wall with necy. bolts & nuts (6 mm dia x 62 mm long)

Supply & Fixing Socket type fan regulator (Step type) (Brand Approved by EIC) on existing sheet metal switch board with bakelite/ perspex top cover by screw incl. making necy. connections etc.

Supply of 240V 1400 mm Sweep A.C Ceiling fan (colour- Brown, Model-ARCTIC AIR) with all accessorioes and down rod wire with necessary connection as per G.S (Make: Orient )

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire.

Supply & Fixing 240 V, 25 A, Modular type starter (Brand approved by EIC) with 25A Modular switch type DP MCB (CCurve) and 4 Module GI Modular type switch board with 4 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc.

Excavation of soil for installation of Earth Electrode and filling & ramming forsoft Soil.

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below By TATA-Medium GI pipe

Extra treatment of soil by using salt and charcoal for pipe electrode.

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work(1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe

S&F earth busbar of Galv .M.S plat 50mm *6mm on wall having clearance of 6mm from wall incl. providing drilled holes on the busbar complete with G.I bolts , nuts ,washers spacing insulator etc. as required

Connecting the equipments to early busbar incl. S&F No. 8 SWG G.I. wire on wall /floor with stapels as per G.S.

2 Kwp Off grid Solar System

Supply, Installation, Testing and Commissioning of 2 KW roof top Off-grid solar system with Mono crystalline Solar PV modules, 530 wp - 04 Nos( Make-Tata Power Solar), AJB, 3 I/P, 3 O/P with fuse, SPD type-II, ACDB with SPD 1 ph (Make-Eligant or equivalent), 12 volt 200 Ah Flooded LMLA Battery- 02 Nos ( Make-Tata Power ), 12 volt 200 Ah Flooded LMLA Battery - 02 Nos ( Make-Exide ), Module Mounting Structure with Foot Ballast - 01 Job (ISI approved), Solar Off grid PCU 2.2 KVA, 1 ph, 48 VDC MPPT - 01 No (Make- Tata Power) , Earthing Kit 3.3 M , 50 mm dia, GI rod, Earth pit cover (ISI approved)- 3 set, Earth Strip (25mm x 3 mm), Lightening arrestor Height 1 mtrs Conve -1set, Installation Kit (Comm Cable etc)- 1 set .

Compound light

Supply of 2 Core 4 Sq mm Alluminium XLPE /PVC Armoured cable.

Laying of cable 2 core 4 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables of 2 core 4 sqmm

Finishing the end of 2 core 4 sqmm XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials

Supply & Fixing 240 V 16/20 A Piano key type switch (Brand approved by EIC) on existing sheet metal switch board having bakelite/perspex top cover by screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required.

Distribution wiring in 1.1 KV single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in 20mm size PVC rigid conduit 'FR' (Precision make) incl. necy. fittings as require. (i) 2 x 22/0.3 (1.5 sqmm) + 1 x 22/0.3 (1.5 sqmm) ECC

Supplying & Fixing GI waterproof type looping cable box size 200x150x100 mm deep having 4 mm thick comprising of one 250 V 16 A SPMCB one compression type brass cable gland for upto 2- core 16 sqmm PVC/A cable and having lined with rubber gasketted GI top cover with brass machine screws etc., earthing terminal with lug, on steel tubular pole near base, including S&F 40x6 mm thick, MS clamps with bolts, nuts etc. including painting with anticorrosive paint

Supply only 45 Watt FREEDOM NEO LED streetlight made up of pressure die cast housing with toughened glass and high power LEDs with secondary optics with IP65 protection.Model no-LSTS-45-CDL-M (Make : Crompton /Equivalent )

Fixing only outdoor / street light type fluorescent light fitting or MV light fitting complete with all accessories to be fixed /projected from the wall of the building incl. making holes/providing clamping arrangement & necy. GI reducer as required. S&F 40 mm GI pipe (ISI-Medium) quality 1.5 mts. average length having suitable bend S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall incl. painting etc.

Supplying & fixing medium gauge 40 mm GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required.

Supplying & fixing ABC Stored Pressure type Fire Extinguisher og 6 kg capacity consisting of welded cylinder squeeze lever discharge valve fitted with pressureindicating guage with internal discharge tube,discharge hose and nozzle,suspension bracket,conforming to IS:15683 duly charged with ISI Market Mono Ammonium Phosphate Base ABC Powder conforming to IS:14609 And pressurized with nitrogen gas. Temparature Range(-)30ºC to (+)55ºC.Fire Rating-2A & 21B. Make- Fireshield or equivalent reputed brand.

Supplying & fixing CO2 type Fire Extinguisher og 4.5 kg capacity conforming to IS:15683:2006 made from seamless cylinder conforming to IS:7285 duly approved by chief controller of Explosive,Nagpur,fitted with ISI Marked Controlled valve conforming to IS:3224,high pressure 1 mtr. long discharge hose and horn complete with initial gas charged with carrying handle and wall mounting bracket suitable for operating between (-)30ºC to (+)55ºC,Fire Rating Class-13B. Make- Fireshield or equivalent reputed brand.

Machineries for Makhana Processing Unit

Supply, Installation,Testing, Commissioning and O& M for 3 years of Makhna/Foxnut roasting Machine ( Nos of Machine -1)

Supply, Installation,Testing, Commissioning and O& M for 3 years of Makhna/Foxnut Cleaning, Sorting, Grading Machine ( Nos of Machine -1)

Supply, Installation,Testing, Commissioning and O& M for 3 years of Makhna/Foxnut Colour Sorting Machine ( Nos of Machine -1)

Supply, Installation,Testing, Commissioning and O& M for 3 years of Makhna/Foxnut Weighing & Packaging Machine ( Nos of Machine -1)

Please Enable Macros to View BoQ information