Provn of toilet for ladies at workers canteen at Mil Stn Dappar under GE (P) Dappar

Amount

Surface excavation in soft/loose soil, not exceeding 30cm deep and averaging 15cm deep and getting out, complete all as specified

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in soft/loose soil, complete all as specified

M & L for PCC 1:4:8 Type D2 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

M & L for brickwork with subclass `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge

M&L 40mm thk damp proof course in cement concrete 1:2:4 type B-0 to horizontal or vertical surfaces including necessary formwork

M&L for cement plastering 15mm thick in cemet mortar 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for cement plastering 5mm thick in cement mortar 1:3 as on ceilings or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for cement plastering 15mm thick in cemet mortar (in two layers 10 mm+5mm) 1:4 including mixing of liquid water proofing compound as per manufacturer's instructions on brick work or concrete surfaces or in chajjas/parapet walls etc finished even and fair complete all as specified and as directed by Engineer-in-Charge. Note : WPC will be measured and paid separately.

Supply only integral liquid water proofing compound complete all as specified and directed. Make : Pidilite/Sika

M&L for preparation of newely plaster surfaces on wall and applying two coats of cement based paint on plastered surfaces all as specified.

M&L for preparation of newely plaster surfaces on wall and applying three coat of white wash on plastered surfaces all as specified.

M&L for preparation of newely plaster surfaces of ceiling and applying three coats of white wash all as specified.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing for butt hinge ISI Marked 100mm size, medium weight, cold rolled mild steel complete all as specified and as directed.

S & F 150mm aluminium handles, cast type, anodised complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing for ISI Marked 150mm long aluminium, anodized, barrel tower bolts of extruded section complete all as specified and as directed by the Engineer-in-Charge

M & L for hardcore of broken stone or boulders exc 63mm but n exc. 100mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rolled/rammed to a true surface, complete all as specified

M&L for 100 mm thick PCC (1:4:8) type D-2 using 40mm graded aggregate as in sub base of floor all as specified.

M & L for 40mm thick cement concrete 1:2:4 type B-1, using 20mm graded aggregate as floor finish complete all as specified and as directed by the Engineer-in-Charge

M&L for cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregates as in cills, lintels, upto 1.50 metre clear span, copings, benching, bed plates etc. and in similar works including weathering, slightly rounded or chamfered angles and throating and necessary form works complete all as specified and as directed.

M&L 50 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in plinth protection. Completef all as specified and directed by Engr-in-Charge.

M & L for Non-Skid white ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match OVER 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge

M&L for glazed ceramic white tiles in vertical surfaces such as skirting, dados and riser to steps etc size 250mmx7mm/450mmx350mmx7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match laid over 10mm thick plaster CM (1:4) complete all as specified.

M & L for reinforced Cement Concrete nominal mix 1:2:4 type B1 using 20mm graded aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by the Engineer-in-Charge.

M & L for RCC nominal mix 1:2:4 Type B1 using 20mm graded aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge

M&L formwork to sides and soffits of floor or roof beams, beam haunch- ings, girders, bressummers, lintels, cantilevers, shelves including sup• ports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfacecomplete all as specified and directed by Engr-in-Charge.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge

M&L Mild steel TMT bar 5 mm dia and over upto and including 10 mm dia in stirrups, spaces and binders, cut to length, bent to shape required including cranking bending spirally hooping for column, hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9mm dia or securing with clips quality conforming to, as in stirrups, spaces and binders complete all as specified and directed by Engr-in-Charge.

S & F of 15mm size PVC connections with PTMP nuts of length 450mm complete all as specified and as directed by the Engineer-in-Charge

M & L for 75mm bore dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 complete all as specified and as directed by the Engineer-in-Charge

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge

S & F 110mm bore PVC (SWR) bends of any radius, complete all as specified

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge

S & F 75mm bore PVC (SWR) bends of any radius, complete all as specified

S & F 75mm bore PVC (SWR) vent cowl, complete all as specified

M & L for 15mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge

M & L for 20mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge

Cutting chases ,pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting n. exc 10 cm girth complete all as specified.

Supply and fixing for ISI marked 15mm bore bib tap of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by the Engineer-in-Charge.

M & L for 500 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed by the Engineer-in-Charge

S & F of for ISI Marked 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

S & F of ISI marked 15mm bore stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed by the Engineer-in-Charge.

M & L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 100mm bore pipe line complete all as specified and as directed by the Engineer-in-Charge

S & F Pillar Tap of 15mm bore dia, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F viterious china white wash hand basin flat back white in colour ISI marked of size 550mm x 400mm with chromium plated including waste coupling and PVC waste pipe fixed to walls with CI breckets 2 Nos embedded in CM 1:4 type complete all as specified.

S&F10 ltr PVC valveless syphonic action type flushing cistern with brackets flush pipe etc complete including inlet ball valve float and handle including brackets of approved make including all connections & flush pipes for WC complete all as specified.

S&F vitreous china premium/1st quality wash down water closet pan floor mounting (pedestal pattern/EWC) S/P trap white colour of size 520X360X390mm including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc.,with flush pipe and incl. S&F plastic seat cover as recommended by manufacturer closed pattern with flat bottom etc; and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and including jet spray complete in all respect all as specified. Make : Cera (Conventional) or Hindware (Slick) equivalent from Parryware

S&F Soap dish, any type, fixed to plugs with chromium plated brass screws completed all as per specified and directed.

S&F of Angle valve 15mm bore stop valve, fancy type, brass chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F brass chromium plated tublar towel rail, 20mm dia, D type 60cm long between flanges completed all as specified and directed.

S&F grating doom 100mm dia of PTMT (min weight 25gms) complete as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil, complete all as specified

M & L for removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

S M BUILDERS

M/S Mahal Enterprises

Supreet Associates