GREYHOUNDS LIFT

8 Passenger Lift: Design, supply, installation, testing and commissioning of passenger elevator in the available shaft for 8 persons capacity with a travelling speed of 1m/sec for a total travel of three floors to operate on 415V, 3 Phase, 50 cycles/sec AC suply etc., including errection of lift including scaffolding and excluding major civil works, seperator channels required if shaft dimensions exceeds standard dimensions , lift pit etc., complete as as per detail specification. Make : OTIS/ KONE/ SCHINDLER Lifts/Mitsubushi Model :Passenger elevator PWI08/10-19 or equivalent. Product:- Monospace Type of elevator:PM Gearless (Located in shaft on top of guide rails) CAPACITY (kgs) : 544 Kg, 8 persons. SPEED (mps) : 1 mps STOPS : 3 Stops With (all opening on the same side) Number of entrances: 3 Number of access sides: 1 POWER SUPPLY : 400/415 Volts (3 Phase AC) OPERATION : Full collective operation CAR GROUP : One car (simplex) MACHINE : PM Gearless (Located above shaft) Minimum Floor to floor height (required) 3600 mm Floor designations:- Travel height: 7.2m Headroom height 4400 mm from last landing finished floor level CAR FINISH : Lintel Height (required) 2180 mm from finished floor level Clear Inside Shaft (available) 2490mm Width x 1650 mm Depth Pit depth: 1400 mm Drive system: Variable Frequency Regenerative (Closed loop) Car Size:1300 mm (W) x 1100 mm (D) x 2200 mm (H) Hoistway Size : 2490 mm (W) x 1650 mm (D) Door Width 900 mm, Door Height 2000 mm Door Opening Direction : Two- panel Center opening door panels with glass Car Design:- *Car Rear Mid Panel = Stainless Steel silver brushed #4(Hairline) *Car Rear Corner Panels = brushed Stainless Steel #4(Hairline) * Car Side Panels = brushed Stainless Steel SUS 304 Car Door Finish : brushed Stainless steel hairline finish * Car Front Panels = brushed Stainless Steel #4(Hairline) FALSE CEILING TYPE: Integrated roof RS60 Lighting Type : Stainless Steel Round Spot LED light VENTILLATION : Cross flow fan HAND RAILS : Round bend Brushed Stainless Steel (ST4) Handrails on rear car panels FLOORING : 20mm Customer Provide Granite Stone Silver Brushed Stainless Steel AISI304 Finishing (ST4) Handrails on rear car panels Flooring: 20mm Customer Provide granite Stone Silver COP:COP for stops :- 1 Full height stainless steel face plate Silver brushed StSt Segment LCD Display Square Surface mounted Buttons with Braille KDS90 Landing Signalization:- Stainless Steel (ST4) /7 segment display surface mounted Silver brushed StSt STANDARD FEATURES : Emergency Car Light Unit, Firemem Drive Anti-nuisance Car Call Protection, Independent Service (for Duplex only), Overload Device, Nudging, Emergency Firemen’s Service, Special Features:- Infrared Curtain Door Protection, Door Time Protection, Emergency Alarm Button, Extra Door Time of Lobby & Parking, Door Open/Close Button, Manual Rescue Operation, Belt Inspection Drive,

Providing independent earthing for Important equipment with 40mm dia 'B' class 2.5m long G.I pipe and 19mm dia 'B' class G.I pipe of 0.3mtr. long connected with reducer providing G.I funnel with mesh enclosed in C.C/ brick massonry chamber of 450m x 450m x 400mm with R.C.C. Slab cover duly providing staggered holes filling with 20Kg Salt and 40Kg Charcoal or 40Kg bentonite powder from the bottom of the pipe giving earth connection from electrode through G.I strip of 40 x 6mm x 200mm length with all accessories and labour charges complete, as per IS specifications 732/1982 (Part II) but excluding GST.

Supply and Run of 25mm x 6mm G.I Strip including cost of all accessories and labour charges etc., complete.but excluding GST.

Supply and fixing of ISI 25mm outer dia heavy grade with IS:9537 part 3 rigid PVC pipe on surface on wall with all accessories fixing on chromium plated metallic base saddles including all labour charges etc., complete but excluding GST. Makes : Sudhakar / Modi / VIP/Precission.

Supply and fixing of 20A 2 Module Modular Socket with shutter and 16A / 20A 1 Way 1 Module Modular Switch duly recessed in wall with 3 Module Hot Dip Galvanized Modular Metal Box size covered with 3 Modular Cover Frame including earth connections and all labour charges etc., complete but excluding GST. [Power plug] Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus / GM Four Five / Anchor Roma Plus/Gold Medal Curve.

Wiring with 2 runs of 1.5 Sqmm HFFR PVC insulated 1100V grade as per IS:694/2010, IS 17048 specification for Copper cable in existing pipe with 6A / 10A 1 Way 1 Module Modular Switch control with suitable Module Hot Dip Galvanized modular type Metal Box covered with suitable Modular Cover Frame, without 3 Plate Jumbo Ceiling Rose including all labour charges etc., complete for light and bell points in Non-Residential Buildings but excluding GST. Copper cable Make:Sudhakar (HFFR) / Nakoda (HFFR), KEI (HFFR), RR kabel (HFFR), Polycab (HFFR). Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus / GM Four Five / Anchor Roma Plus/Gold Medal Curve.

Supply and run of 3 of 2.5 Sqmm HFFR PVC insulated 1100V grade as per IS:694 / 2010, IS 17048 specification for Copper cable in existing pipe for 2 runs of mains & 1 run of earth continuity inlcuding all labour charges etc., complete but excluding GST. Make: Sudhakar (HFFR) / Nakoda (HFFR), KEI (HFFR), RR kabel(HFFR), Polycab(HFFR).

Supply of 16 Sqmm 4 Core PVC / XLPE Insulated, Flexible Armouring Flexible Copper cable as per IS 7098 / Part-I / 1988 including all transportation charges etc., complete but excluding GST. Makes : RR kabel / Nakoda / Polycab / RPG / KEI /Sudhakar

Supply and run of 5 of 6.0 Sqmm HFFR PVC insulated 1100V grade as per IS:694 / 2010, IS 17048 specification for Copper cable in existing pipe for 4 runs of mains & 1 run of earth continuity inlcuding all labour charges etc., complete but excluding GST. Make:Sudhakar (HFFR) / Nakoda (HFFR), KEI (HFFR), RR kabel (HFFR), Polycab (HFFR).

Supply and transportation of 10W LED Bulk head fitting with milky diffuser heat sink integrated with housing with all accessories etc complete with 5 years warranty warranty but excluding GST. LUMINAIRE MAKE : CROMPTON / HAVELLS. LED MAKE : CREE / NICHIA / OSRAM.

Supply and fixing of 12 Way SPN DB with IP 43 Protection as per IS:13032 and suitable for single phase 4 Nos S.P and 1No 4P out goings and for 1No Incommer, including internal connection and labour charges for flush mounting etc., complete but excluding GST. Incommer: 63A FP MCB -1No. Outgoing: 10kA-40A FP MCBs - 1 Nos 10 kA - 6-32A range SP MCBs - 4Nos DB Makes: ABB / C&S /LK (L&T) Isolator Make: ABB / Havells/C&S MCB Make: ABB / Havells/C&S.

Labour charges for run of U.G cable on wall / existing pipe with necessary fixing arrangments such as saddles, clamps,wooden separators etc., (as directed by departmental official) etc., complete.

EARTH WORK EXCAVATION FOR FOUNDATIONS AND DEPOSITING ON BANK, FOR ALL LIFTS AND WITH AN INITIAL LEAD OF 10M INCLUDING ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES SUCH AS SHORING, SHEETING, PLANKING, STRUTTING, DEWATERING SITE CLEARANCE, CLEARING SHURBS, BRUSHWOOD, UNDER GROWTH AND SMALL TREES NOT EXCEEDING 300 MM GIRTH, MEASURED AT ONE METRE ABOVE GROUND ETC., COMPLETE FOR FINISHED ITEM OF WORK INCLUDING DEWATERING CHARGES ETC AS PER SS - 20 B FOR STIFF BLOCK COTTON SOIL , HARD RED EARTH, MURRAM, ORDINARY GRAVEL - MANUAL MEANS UP TO 3M DEPTH - FOUNDATION OF BUILDING (APSS 308)

CEMENT CONCRETE (1:4:8) PROP. USING 40MM HARD GRANITE MACHINE CRUSHED METAL WITH MACHINE MIXING UP TO PLINTH LEVEL INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LAYING, CURING, FINISHING, SEIGNIORAGE ALL OTHER INCIDENTAL, OPERATIONAL, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK. FOUNDATION BED AND UNDER STONE SLAB FLOORING. (APSS NO: 402).

RANDAM RUBBLE MASONRY USING HARD GRANITE STONE IN CM(1:6) PROP. INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, SEIGNORAGE CHARGES,LABOUR CHARGES, CURING, ETC., COMPLETE FOR FOUNDATIONS AND BASEMENTS FOR FINISHED ITEM OF WORK. APSS NO: 615).

BRICK MASONRY IN CEMENT MORTAR (1:6) PROP USING FLY ASH BRICKS OF SIZE 290 X 225 X140 MM -CLASS 5, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHAGES , SCAFFOLDING, CURING, LIFT CHARGES, ETC., COMPLETE FOR FINISHED ITEM OF WORK WITH A COMPRESIVE STRENGTH OF 5N/ MM2 EXCLUDING GST AND SEIGNIORAGE CHARGES ON ALL MATERIALS. FOR SUPERSTRUCTURE WALLS OF 225 MM THICK FOR GROUND FLOOR UP TO 3.66M HEIGHT (APSS NO. 504 & 501)

BRICK MASONRY IN CEMENT MORTAR (1:6) PROP USING FLY ASH BRICKS OF SIZE 290 X 225 X140 MM -CLASS 5, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHAGES , SCAFFOLDING, CURING, LIFT CHARGES, ETC., COMPLETE FOR FINISHED ITEM OF WORK WITH A COMPRESIVE STRENGTH OF 5N/ MM2 EXCLUDING GST AND SEIGNIORAGE CHARGES ON ALL MATERIALS. FOR SUPERSTRUCTURE WALLS OF 225 MM THICK FOR FIRST FLOOR UP TO 3.66M HEIGHT (APSS NO. 504 & 501)

BRICK MASONRY IN CEMENT MORTAR (1:6) PROP USING FLY ASH BRICKS OF SIZE 290 X 225 X140 MM -CLASS 5, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHAGES , SCAFFOLDING, CURING, LIFT CHARGES, ETC., COMPLETE FOR FINISHED ITEM OF WORK WITH A COMPRESIVE STRENGTH OF 5N/ MM2 EXCLUDING GST AND SEIGNIORAGE CHARGES ON ALL MATERIALS. FOR SUPERSTRUCTURE WALLS OF 225 MM THICK FOR SECOND FLOOR UP TO 3.66M HEIGHT (APSS NO. 504 & 501)

VRCC M-20 NOMINAL MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS , MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING, LIFTING (MANUAL) ETC., WITH MINIMUM CEMENT CONTENT OF 400 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING STEEL CENTERING PLATES ETC., COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES AND EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, FOR FINISHED ITEM OF WORK FOR PLINTH BEAM (APSS NO.403)

VRCC M-20 NOMINAL MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS , MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING, LIFTING (MANUAL) ETC., WITH MINIMUM CEMENT CONTENT OF 400 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING STEEL CENTERING PLATES ETC., COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES AND EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, FOR FINISHED ITEM OF WORK FOR GROUND FLOOR BEAM (APSS NO.403)

VRCC M-20 NOMINAL MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS , MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING, LIFTING (MANUAL) ETC., WITH MINIMUM CEMENT CONTENT OF 400 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING STEEL CENTERING PLATES ETC., COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES AND EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, FOR FINISHED ITEM OF WORK FOR FIRST FLOOR BEAM (APSS NO.403)

VRCC M-20 NOMINAL MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS , MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING, LIFTING (MANUAL) ETC., WITH MINIMUM CEMENT CONTENT OF 400 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING STEEL CENTERING PLATES ETC., COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES AND EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, FOR FINISHED ITEM OF WORK FOR SECOND FLOOR BEAM (APSS NO.403)

VRCC M-20 NOMINAL MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS , MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING, LIFTING (MANUAL) ETC., WITH MINIMUM CEMENT CONTENT OF 400 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING STEEL CENTERING PLATES ETC., COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES AND EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, FOR FINISHED ITEM OF WORK FOR GROUND FLOOR LINTELS (APSS NO.403)

VRCC M-20 NOMINAL MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS , MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING, LIFTING (MANUAL) ETC., WITH MINIMUM CEMENT CONTENT OF 400 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING STEEL CENTERING PLATES ETC., COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES AND EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, FOR FINISHED ITEM OF WORK FOR FIRST FLOOR LINTELS (APSS NO.403)

VRCC M-20 NOMINAL MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS , MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING, LIFTING (MANUAL) ETC., WITH MINIMUM CEMENT CONTENT OF 400 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING STEEL CENTERING PLATES ETC., COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES AND EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, FOR FINISHED ITEM OF WORK FOR SECOND FLOOR LINTELS (APSS NO.403)

PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. with sponze finishing, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, LIFTING ( MANUAL) CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE. FOR FINISHED ITEM OF WORK. GROUND FLOOR FOR UNSUPPORTED HEIGHT UPTO 3.66M (APSS NO: 901&904)

PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. with sponze finishing, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, LIFTING ( MANUAL) CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE. FOR FINISHED ITEM OF WORK. FIRST FLOOR FOR UNSUPPORTED HEIGHT UPTO 3.66M (APSS NO: 901&904)

PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. with sponze finishing, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, LIFTING ( MANUAL) CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE. FOR FINISHED ITEM OF WORK. SECOND FLOOR FOR UNSUPPORTED HEIGHT UPTO 3.66M (APSS NO: 901&904)

PROVIDING "HYSD/TMT" STEEL BARS OF DIFFERENT DIAMETERS BELOW 36MM DIAMETER Fe 500 GRADE (AS PER IS 1786 - 2008 AND ALL ITS LATEST AMMENDMENTS) Reinforcement Steel (HYSD/TMT) from steel Manufactureres like TATA, SAIL, VSP, JSW, Jindhal Panther, AF Star TMT/MS Life TMT, Radha TMT, Suguna TMT, V-XEGA, GOEL TMT, SHYAM STEEL AND BALAJI SHAKTI INCLUDING CUTTING, BENDING TO REQUIRED SIZES AND SHAPES, PLACING THEM IN POSITION WITH COVER BLOCKS OF APPROVED SHAPE AND SIZE, TYING FIRMLY WITH M.S BINDING WIRE OF SWG, FORMING GRILLS FOR REINFORCEMENT WORKS AS PER APPROVED DESIGNS AND DRAWINGS TO BE SUPPLIED AT THE TIME OF EXECUTION OF WORK INCLUDING COST AND CONVEYANCE OF DEFORMED BARS, BINDING WIRE, COVER BLOCKS AND ALL WASTAGES SUCH AS OVER LAPS, COUPLINGS, WELDED JOINTS, CHAIRS, SPACE BARS ETC., AS DIRECTED BY THE ENGINEER-IN-CHARGE AND ALL OPERATIONAL, INCIDENTAL LABOUR CHARGES SUCH AS CUTTING, BENDING, PLACING IN POSITION, TYING ETC., EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK FOR ALL LENGTHS AS PER DRAWINGS AND TECHNICAL SPECIFICATIONS FOR BARS BELOW 36MM DIA WHERE THEY ARE NOT WELDED.

PROVIDING CLADDING WITH HIGH POLISHED GRANITE SLAB 16 TO 18MM THICK UPTO 8'-00"(2.43M) OTHER THAN BLACK PREMIUM COLOUR SET OVER BASE COAT OF CM (1:3) 20 MM THICK WITH CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD AT THE RATE OF 3.30 KGS PER SQM AND JOINTED WITH WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO FULL DEPTH, INCLUDING COST OF ALL MATERIALS LIKE STONES, CEMENT, SAND AND WATER ETC., COMPLETE INCLUDING SEIGNIORAGE CHARGES,LIFTING (MANUAL) ETC., COMPLETE FOR FINISHED ITEM OF WORK FOR GROUND FLOOR LIFT WALLS

PROVIDING CLADDING WITH HIGH POLISHED GRANITE SLAB 16 TO 18MM THICK UPTO 8'-00"(2.43M) OTHER THAN BLACK PREMIUM COLOUR SET OVER BASE COAT OF CM (1:3) 20 MM THICK WITH CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD AT THE RATE OF 3.30 KGS PER SQM AND JOINTED WITH WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO FULL DEPTH, INCLUDING COST OF ALL MATERIALS LIKE STONES, CEMENT, SAND AND WATER ETC., COMPLETE INCLUDING SEIGNIORAGE CHARGES,LIFTING (MANUAL) ETC., COMPLETE FOR FINISHED ITEM OF WORK FOR FIRST FLOOR LIFT WALLS

PROVIDING CLADDING WITH HIGH POLISHED GRANITE SLAB 16 TO 18MM THICK UPTO 8'-00"(2.43M) OTHER THAN BLACK PREMIUM COLOUR SET OVER BASE COAT OF CM (1:3) 20 MM THICK WITH CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD AT THE RATE OF 3.30 KGS PER SQM AND JOINTED WITH WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO FULL DEPTH, INCLUDING COST OF ALL MATERIALS LIKE STONES, CEMENT, SAND AND WATER ETC., COMPLETE INCLUDING SEIGNIORAGE CHARGES,LIFTING (MANUAL) ETC., COMPLETE FOR FINISHED ITEM OF WORK FOR SECOND FLOOR LIFT WALLS

PROVIDING AND APPLYING SYNTHETIC PLASTER PUTTY OR PLASTER OF PARIS PUTTY OR LIME PUNNING OF AVERAGE 1 TO 2 MM THICKNESS OVER PLASTERED SURFACE TO PREPARE THE SURFACE EVEN AND SMOOTH AFTER THOROUGHLY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDERED MATERIALS, APPLYING EMERY PAPER, SAND THE SURFACE, CLEAN & WIPE OFF LOOSE DUST, APPLYING KNIFING PASTE FILLER BY PUTTY KNIFE / MUSLIN PAD, AIR DRY FOR 2 - 3 HRS, SAND WITH 180 AND 320 NO., EMERY PAPER FOR THE SURFACE PREPARATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO WORK SITE AND ALL OPERATIONAL, INCIDENTAL, LABOUR CHARGES ETC. COMPLETE FOR FINISHED ITEM OF WORK.

PAINTING TO NEW WALLS WITH THREE (3) COATS OF Synthetic Polymer luxury Plastic emulsion /solvent based lustre paint of superior grade having (VOC < 50 Gms./Lit) OF APPROVED BRAND AND SHADE (ASIAN /BERGER /NEROLAC /SAICOAT /INDOCEM OR EUIVALENT) OVER ONE COAT OF PRIMER OF APP BRAND AFTER THOUROULY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDER MATERIALS INCLUDING COST OF ALL MATERIALS TO THE INTERIOR FACES OF WALLS AS DIECTED 2COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750ML OF WATER WITH AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS (TOTAL3 COATS) WITH SURFACE PREPARATION ETC., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, BRUSHES, LABOUR CHARGES, CURING, SCAFFOLDING LIFTING(MANUAL) AND ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK