Proposed Beautification and Installing of Musical Fountain at Various Lakes in MBMC Area (Proposed Basic Facility Development Fund)

Amount

Description

Dismantling stone masonry in lime or cement mortar including stacking the materils as directed with all leads, lifts etc.

Removing cementtiles,or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete

Removing rich mix cement concrete including stacking the spoils as directed with all leads, lifts etc, complete

Excavation for foundation in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 m. beyond the building area and stacking or spreading as directed, dewaterin, preparing the bed for the foundation and necessary back filling, ramming, watering, including shoring and strutting as necessary complete. ( Spec.No. : Bd.A.1Page no 259/ CSR Page No.150

Excavation for foundation in Hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m.) By Mechanical Means

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 3.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary)

Providing soling using 80 mm size granite / quartzite / gneiss / trap metal in 15 cm. layer including hand packing filling voids with sand / grit, ramming, watering complete. (Spec. No. : As directed by Engineer-in-charge /Page No. 154)

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork, laying/pumping cover blocks,compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layersincluding watering and compacting etc. complete.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Compound Wall Column

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap /granite /quartzite /gneiss metal for R.C.C. beams and as per detailed designs and drawings or as directed including steel centering, formwork, coverblocks, laying /pumping, compaction and roughening the surface if special finishish to be provided and curing etc. complete. (Excluding reinforcement and structural steel). withfully automatic microprocessor based PLC with SCADA enable dreversible Drum Typemixer/concreteBatch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Plinth Beam

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Ground Floor

Providing and fixing in position HCRM/CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part3) -1984 in extra fine jointing mortar of fixoblock of Ultra Tech or equivalent in superstructure including striking joints, raking out joint sand scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)

Ground Floor

Providing and constructing masonry in Auto claved Areaclaved (Celluar) Concrete Block of aproved manufacturer confirming to IS2185 Part III 1984 of size (625 x 240 x 100) mm in extra fine jointing mortar of fixoblock of in half brickthick wall including 2 hoopironstrips 25 mm x1.6 mm at every third course, properly bend and bonded at end sscaffolding racking out joints and watering compete

Ground Floor

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Ground Floor

Providing internal cement plaster 20mm. Thick in Single coats in cement mortar 1:3 with out neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete.

Ground Floor

Providing internal cement plaster 12mm. Thick in Single coats in cement mortar 1:3 with out neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete.

Ground Floor

Providing internal cement plaster 6 mm thick in a single coat in cement mortar 1:3 without neeru finish to concrete surface in all positions including scaffolding and curing etc. Complete

Ground Floor

Providing and applying gypsum plaster (with Gypsum materia l) with finishing with gypsum material in 10 to 13 milli meter thickness to previously plastered surface /or on newly brick surface (Excluding rough cast plaster) in all position including preparing and Finishing the surface scaffolding etc.complete.

Ground Floor

Providing and applying Royale Luxury Emulsion of approved make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. wall primer with brush by adding mineral turpentine oil by 8 to 10% or water by 15 to 20% allowing to dry for 6 to 8 hours After applying acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45% or 65 to 70% by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45% or 65 to 70% by roller. (With prior approval of S.E.)

Ground Floor

Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases (NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram / 15l). plaster crack should be filled by Acrylic base Crack seal / Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise on site technical reports from the concerned company technologist.

Ground Floor

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1kg/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 kg/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 kg/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete.

Ground Floor

Providing waterproof plaster in W.C. and bath 20 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 kg. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) etc. complete.

Waterproofing

Providing cement based waterproofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved waterproofing compound and laying the brick bats on bottom layer in C.M. 1:5 admixed with approved waterproofing compound filling upto half depth of brick bats, curing this layer for 3days, applying cement slurry over this layer joints of brick bats with C.M. 1:3 admixed with approved waterproofing compound and finally top finishing with average 20mm. thick layers of same mortar added with jute fiber at 1 Kilogram per bag including finishing the surface smooth with cement slurry admixed with approved waterproofing compound. Marking finished surface with false squares of 300 mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs.500/- including ponding test etc. complete.

Providing and laying jointless Polydee-LM, a highly flexible elastometric coating for RCC / cementitious surface for terrace waterproofing on B.B. Coba / R.C.C, after application of TP-42 Primer on perfectly clean surface (free from loose dust and foreign matter) application of 1st coat of Polydee-LM @ 700 gms / One Square Metre and applying 2nd coat of Polydee-LM @ 700 gms / One Square Metre and finishing the same with sprinkling the AG-10 granules on the wet coating. (After finishing covering the treatment with 25 mm cement plaster for protection with fibrillated 6mm Plyplast fibre @ 125 gms / One Square Metre to be paid in separate item.) covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/- etc. complete.

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to10 mm thicknes sand confirming to IS.15622 -2006 (GroupBla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete.

Ground Floor

Providing and laying Vitrified MATT finish having decorative type of size 1000 millimeter x 1000 millimeter of 8to10 milli meter thickness (on a existing Dado) with bonding chemical and confirming to IS15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of bonding chemical filling joints, curing and clearing etc. complete.

Ground Floor

Providing and fixing machine cut mirror polished 18 mm to 20 mm thick telephone black granite / Amba White / Catbarybrown / RBI red / Ocean Brown granite stone partition with full moulding the edges etc. complete . Both side polish

Ground Floor

Providing and laying telephone black /Amba White / Cadburybrown / Rubyred / Ocean Brown granite stone of 18 to 20 mm thick for door frame / dado / window boxing etc. On C.M. 1:6 including filling joints with polymer base filler no sing / moulding the sharp edges wherever necessary, curing, etc. complete.

Ground Floor

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Catbary brown / RBI red / Ocean Brown granite stone for tread sand risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.

Ground Floor

Providing and fixing 40 mm diameter and 1.5 mm thick Stainless steel hand railing in S.S.304 Grade including fabricating, fixtures, errecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete

Supply & Fixing of Rock / Stone Finished outdoor vitrified flooring Tiles 20 mm thick and required width wide in plain pattern including Cement float, filling joints, with neat cement slurry, Natural sand, curing and cleaning complete. with prior approval of concerned Superitending Engineer

Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixture sand fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete.

Ground Floor

Providing and fixing frame with / without ventilator of size as specified with Country cut teakwood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete

Ground Floor

Providing and fixing CCTW beading of size 40 mm x 20 mm to the door frame including chamfering finishing with 3 coats of oil painting etc. complete

Ground Floor

Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 Kilogram/Running metre. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 Kilogram /Running metre. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 Kilo gram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. And handle section 40 x 18 x 1.25 mm at weight 0.417 Kilo gram /Running metre. and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram / Running metre. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising with box.Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 Kilogram/Running metre. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 Kilogram/Running metre. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. And handle section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising with box.

Ground Floor

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete

Ground Floor

Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram /One Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Ground Floor

Providingand fixing mild steel grill gate with angle iron frame 65 mm x 65 mm x 10 mm with iron bars at 150 mm C/C and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade Weight of gate 35 Kilogram/Smt.

Providing and constructing Brick Masonry inspection trap Chamber 90cm x 45cm including 1:4:8 C.C foundation, 1:2:4 C.C.channels/half round glazed stoneware pipe channel, salt glazed stone-ware intercepting trap with rodding pipe set in 1:4:8 cement concrete block, brick masonry plastering inside and Outside, fixed in cement concrete with R.C.C. Cover medium duty 140 Kilogram. etc complete

Ground Floor

Providing and fixing 15 cm x 10 cm salt glazed stone ware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stone ware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing and laying for 150 mm dia salt glazed stone ware pipe including fittings Such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete.

Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete.

Providing and fixing orissa type colour glazed earthenware 625 x 450 mm. w.c. pan including trap, C.I. soil and vent pipe upto the outside face of wall including 100 mm. dia. C.I. plug, bend, 15 mm. thick 10 litre PVC flushing cistern with all necessary pipe connection etc. complete.

Providing and fixing White Glazed Earthenware full stall type Urinal with P.V.C. flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 mm dia. P.V.C flush pipe with fitting sand flushing arrangement including lead soil pipe, lead trap, soil pipe connectionup to the outside face of the wall

Providing and fixing White glazed with bottle trap earthenware Wash Hand Basin of 63 x 45 cm size including cold water piller taps, brackets, rubber plugs and brass chain, stop tap, chromium plate bottle trap and necessary pipe connections including UPAC waste pipe and trap upto the outside face of the wall, making good the damaged surface, testing etc. complete.

Providing and fixing European type wall-hung white water closet of approved make with push valve concealed type with cover plate 32 mm size of approved make includings oil pipe, vent pipe upto outside face of wall, 100 mm dia. G.I. plug bend inlet pipe all fittings, cuttingand making good walls, floors etc. complete.

Providing and fixing 15 mm dia. Screw down bib /stop tap of brass including necessary socket union nut complete.

Ground Floor

Providing and fixing 20 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete.

Ground Floor

Providing and fixing 25 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete.

Ground Floor

Providing and fixing screw down 15 mm dia. Wheeled stop tap of brass including necessary sockets/union nut complete

Ground Floor

Providing and fixing screw down for 20 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Ground Floor

Providing and fixing screw down for 25 mm dia. Wheeled stop tap of brass including necessary sockets /union nut complete.

Ground Floor

Providing and fixing screw down for 32 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Ground Floor

Providing and fixing screw down for 40 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Ground Floor

Providing and fixing screw down for 50 mm dia. Wheeled stop tap of brass including necessary sockets/ union nut complete.

Ground Floor

Alluminium foldable ladder for store Providing & Fixing Foldable Alluminum Ladder 1500 mm. Ht.

Providing and fixing push cock (Self closing tap) symet type of 15mm dia.including necessary socket, testing etc. complete.

Ground Floor

Providing and fixing 10 cm PVC nahani trap with grating etc. complete.

Ground Floor

Providing and fixing on walls/ ceiling/ floor 15 mm dia. uPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ceiling/floor 20 mm dia. uPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 25 mm dia. uPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 32 mm dia. uPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls /ceiling/ floor 40 mm dia. uPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 50 mm dia. uPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

Providing and fixing 75 mm dia stabiliser pipe /P.V.C. soil vent /waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete

Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete

Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Providing and fixing 50mm diameter water meter with non-return valve including strainer,sockets/ union nut and including water meter box making locking arrangement and lock. [without chamber]

Providing and fixing chromium plated towel rod 16 mm dia and 75 cm. in length including all accessories complete.

Providing and fixing in position UPVC ultra violet stabilized 110 mm outer diameter cowl dome confirming to I.S.-4985 including making joints with solvent cement etc. complete

Providing and laying weep holes of 100 mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete.

Providing and fixing 90 cm x 60 cm Granite plate engraving 10 cm. Height letter, figures including painting the lefters/figures with approved colour and shade complete

Providing structural steel work of rectangular hollow steel section for steel trusses, other similar trussed items like purlin and members with all bracing, gusset plates etc. as per detailed designs and drawings

Providing and fixing plain zinc sheeting of 0.80 mm thick (22 B.W.G.) over the ridge hip or valley to galvanized iron sheet roofing including all fastening and bolt galvanised iron screws

Providing and Fixing Rubber flooring with 100mm p.c.c. & 100 soling.

Providing and fixing FRP Scalpture (Animal Statue) 1.2 mt Height (Quation) As derected by Enginner -in- Charge

3D painting- Designing, Conceptualization & painting of 3D artistic on any surface at all height and location as directed. The paint should be used for the artistic painting is high quality acrylic paint. painting should be coated with weather proof warnish.

Transportation of excavated earth including loading and unloading per truck trip of 6.00 cubic meter capacity per trip (With Machine Loading for 25 Lead in km)

Providing & Supplying & installation of Air walker etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of Seats & Waist Machine etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of Abdomen Rack etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of Pull down device etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of Sit & Push up device etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of Pendal trainer & parallel bar etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of Walking machine etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of Health ridding machine etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of Body building seesaw etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of Torsinal weast treadmill etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of leg recovery machine etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of Seated leg body frame etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of lumbosacral device etc.complete.Spec.- As Directed Engineer-in-charge.

Providing & Supplying & installation of Double wking machine etc.complete.Spec.- As Directed Engineer-in-charge.

SINGLE SWING WITH BELT ASSEMBLY (Proving and Fixing) Rec. Age :- 4-14 yrs. The area :- 3.0 m x 2.5 m Safe play area :- 4 m x 3.5 m In the swing the leg support is made up of 40 NB GI pipes and toppipe is of 50 NB GI pipes with GI junction box with powder coating.The swing seat is made up of 10 mm thick rubber belt. The belt seat is affixed on 6 mm rubber coated GI chain. The ball bearings are mounted inside a specially designed nylon clamp. All pipes are ‘B’ class pipes All Structures are to be Powder Coated. All Work Done As Per General Raw Material Sheet Added Below. Work done should be as per engineer incharge.

SINGLE FRP ROLLER SLIDE 1.5 MT (Proving and Fixing) Age Group :- 4 – 12 yrs. Product Area :- 5.8 m x 1.0 m Safe Play Area :- 6.8 m x 2.0 m The roller slide is made up of FRP. The slide chute consists of molded plastic rollers spread over the length. The rollers are made up of HDPE with UV stabilized pigment. The square platform of the slide is made up of the Fiberglass reinforced plastic. The vertical platform support pipes used are of 80 NB powder coated GI pipes. The railing is made in rotational molding. The slide entry is affixed on 80 NB and 80 x 20 NB nylon clamp. The ladder frame is made in 20 NB and 25 NB powder coated GI pipes. The triangular steps are made in 16 SWG GI sheets. All pipes are ‘B’ class pipes All Structures are to be Powder Coated. All Work Done As Per General Raw Material Sheet Added Below. Work done should be as per engineer incharge

As derected by Engineer-Incharge.

MULTI SEATER SEE-SAW (Proving and Fixing) Per No Age Group :- 3- 10 yrs. Product Area :- 3.0 m x 0.5 m Safe Play Area :- 4.0 m x 1.5 m Material Specification : The Multi Seater See saw comprises four roto seats. The lever consists of 20 NB and 80 NB powder coated GI pipes. The bearing used in this item is heavy duty nylon bush type. The stand for see saw is made using 50 NB GI pipe. All pipes are ‘B’ class pipes The Foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x0.45m and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Work done should be as per engineer incharge\40km. are considered.

As derected by Engineer-Incharge.

Providing cast in situ / ready mix M20 grade cement concrete for head walls of CD work / retaining walls etc. including necessary form work, compaction, finishing and curing etc. complete. (with reversible drum type mixer / concrete batch mix plant (pan mixer) with SCADA

Providing and laying of filter media with granular materials / stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2 of MoRTH specifications to a thickness of not less than 600 mm with smaller size to wards the soil and bigger size to wards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition as per drawing and technical specifications etc. complete.

Providing and fixing bituminous pad 25 mm thick for expansion joints in retaining wall, compound wall etc. complete.

Providing and laying Needle Punched and mechanically bonded non woven Geotextile of Type III indigenously manufactured from high quality Propylene staple fibers (continuous filament will not be accepted) on the prepared sub grade for Seperation. (For use this item SE / CE permission is obligatory.)

Providing and Constructing gabion structure 1 Meter high or required section made up of soft mechanically woven hexagonal shaped G.I. wire confirming to IS 16014:2012 having zinc plus PVC coating of over all diameter of 3.7 mm and tying lacing wire of 3.2 mm with edge wire confirming to overall diameter 4.4 mm edges being mechanically selvedge including placing in position, fitting neatly with trap stone rubble (15 to 23 cm) all loose ends to be securely tied (Excluding transportation) etc. complete.(InDryconditionandfor under water installation extra cost to be considered)

Providing dry rubble stone pitching 23 cm (about 9) thick including all material, quarry spalls, labour etc. complete.

Providing uncoursed rubble trap / quartzite / gneiss stone masonary in cement mortar 1:5 for piers, abutments, wings, returns, head-walls, parapet etc. including bailing out of water, striking joints of the non exposed faces, pointing the exposed faces with cement mortar 1:3, scaffolding, watering to masonary and etc. complete.

Transpotation of Excavated surplus material like soil, murum etc. upto lead of 20KM

Providing and erecting chain link fencing 1.6 M. height with G.I. chain link of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16 mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete.

Providing detailed layout plan of area in scale1:500 including carrying out contour survey and detailed Engineering plane table Survey with the help of 24 Alidade .The dolomite area measurement of the plot and structures ,trees ,overhead line and underground service amenities with in the area, with triangular method and giving detailes of the structures, such as total area, type of building and distance from all corners taking trial pit 0.5 x 0.5 x 2.00 m.-2 Nos. per acre and collection of record from city survey / D.I.L.R. authorities and authentication.The plan shall be traced on 75 micron polyster film and shall be submitted along with three Amoniaprints. The contour levels shall be marked at 0.5 Meter intervals.Note:-The items includes-1)Traversingworkwiththeodoliteandsteeltape .2)LevellingGridWorkoftheterrain. 3)DetailedEngineeringSurveyandcontouringworkoftheterrain. 4)Plottingwork. 5)Collection of Record. a)upto1Acre

BASIC TEST OF CEMENT Standard Consistancy, Fineness, Specific Gravity, Setting Time ( Initial & Final ), Compressive Strength, Soundness.

BASIC TEST OF AGGREGATE.

a) Water Absorption, Specific Gravity,Impact Value, Crushing Value.

b) Sieve Analysis.

c) Abrasion Value.

d) Flakiness Index & Elongation Index.

e) Stripping Value. (for Bituminous Work)

f) Soundness

FINE AGGREGATE.

a) Fineness Modulus ( Sieve Analysis ),Silt & Clay Content

b) Chloride & Sulphate Content.

c) Silt Factor.

CONCRETE

a) Compressive Strength OF C.C. Cube (Set of 3 cubes)

b) Concrete mix design by Accelerated curing method. (By Accelerated curing method)

WATER PH Value, Sulphate & Chloride Content.

STEEL BAR TESTING

a) Upto 16 mm (Set of 3 Bars)

b) Above 16 mm (Set of 3 Bars) (Tensile strength, %, Elongation, Yield Stress,Weight-Per Meter, Bend / Rebend Test, Proof Stress.)

SOIL / MURUM Plate Load Bearing Test.(Excluding Transportation)

SITC of Projector with specifications mentioned below and as per direction of Engineer-in-charge. Brand and Model Epson L1755UNL or Simillar Projection System: High-aperture Epson 3-chip 3 LCD Native Resolution: WUXGA (1920 x 1200) w/ 4K Enhancement Technology1 Brightness: 15,000 lumens

Custom made Weather proof projector casing to be made in metal powder coating Dimension: 23.1 x 19.4 x 8.3in Waterprooj projector case Power Coated Epoxy finish for waterproofing Rubber sealed IP31 rated Wall, Table or Ceiling Mounting option

SITC of projectors lens with specifications mentioned below and as per direction of Engineer-in-charge. Projector Lens ELPLL08 or Simillar Interchangeable lens — for Pro L projectors up to 20,000 lumens and Pro G7000 Series projectors Wide lens shift — for added flexibility High-quality design — up to 1000" screen size support; 1.8 to 2.5 F-number; 119 mm to 165.4 mm focal length Zoom ratio — 1 – 1.4 Weight — 4.9 lbs (2200 g) Up to 8,500-lumen projectors — WUXGA/WXGA 7.21 to 10.11 throw ratio; lens shift—vertical: -67 percent to +67 percent, horizontal: -30 percent to +30 percent 9,000- to 20,000-lumen projectors — WUXGA 5.27 to 7.41 throw ratio; lens shift—vertical: -60 percent to +60 percent, horizontal: -18 percent to +18 percent Native 4K projector — 5.09 to 7.16 throw ratio; vertical: -58 percent to +58 percent, horizontal: -16 percent to +16 percent

SITC of Computer Intel Core i7 with specifications mentioned below and as per direction of Engineer-in-charge. Brand and Model : Dell or Simillar RAM 16GB DDR4 Storage 240GB SSD Graphics Card RTX 3060 Windows 11 24in Monitor Keyboard mouse

AUDIO SYSTEM

SITC of Speakers with specifications mentioned below and as per direction of Engineer-in-charge Two way speaker system Dimension: 18" x 9" x 10" Mount Type: On pole Make - Audio Focus or similar RXT108P: Low power Speaker RXT108P: Low Power Speaker

SITC of Speakers with specifications mentioned below and as per direction of Engineer-in-charge Two way speaker system Dimension: 28" x 14" x 18" Mount Type: On pole Make - Audio Focus or similar RXT112P: RXT112P: High Power Speaker

SITC of Speakers with specifications mentioned below and as per direction of Engineer-in-charge High Power Subwoofer Dimension: 18" x 9" x 10" Mount Type: On Floor Make - Audio Focus or similar RXT118P Subwoofer

SITC of Audio Processor with specifications mentioned below and as per direction of Engineer-in-charge RXT - Audio Control, Audio Processor, 8V to 10V, I2C, SOIC, 28 Pins, -40 °C, MEMS Microphone, 1.6V to 3.6V, HCLGA, 4 Pins,

SITC of Amplifier with specifications mentioned below and as per direction of Engineer-in-charge 4CH class D AMplifier freq band: 10hz to 22khz over current protection DC offset protection output power: 500w/ ch @ 8 ohm

SITC of Audio Processor with specifications mentioned below and as per direction of Engineer-in-charge RXT - Audio Control, Audio Processor, 8V to 10V, I2C, SOIC, 28 Pins, -40 °C, MEMS Microphone, 1.6V to 3.6V, HCLGA, 4 Pins,

Supply and Installation of Speaker wire with specifications mentioned below and as per direction of Engineer-in-charge. Type: optical fiber or similar Guage: 2.5sq/mm Connector Type: XT30 IPx Gold plated

FOUNTAIN SYSTEM

Supply and fixing of high Jet Nozzles with Gindal B Class Header, suitable for water effect to achieve height of 30-40 ft. height. Nozzle Specification :- Bronze / Gunmetal / Brass Fine quality Shine chrome made on new technology CNC Cutting. Approx Size 1 Inch,, Thread Size 1/8"BSPT Make : Universal/Premier/Deep n Deep/Orient Fountain/Oase/Aquatic or equivalent. Material: SS or Brass

Supply and fixing of Chasing Effects of Vertical Jet Nozzles with Gindal B Class Header, suitable for water effect to achieve height of 15-25 ft. height. Nozzle Specification :- Bronze / Gunmetal / Brass Fine quality Shine chrome made on new technology CNC Cutting. Approx Size 1 Inch, Thread Size 1/8"BSPT Make : Universal/Premier/Deep n Deep/Orient Fountain/Oase/Aquatic or equivalent. Material: SS or Brass

Supply and fixing of 3d Lotus Nozzles with Gindal B Class Header, suitable for water effect to achieve height of 15-25 ft. height. Nozzle Specification :- Bronze / Gunmetal / Brass Fine quality Shine chrome made on new technology CNC Cutting. Approx Size 1 Inch, Thread Size 1/8"BSPT Make : Universal/Premier/Deep n Deep/Orient Fountain/Oase/Aquatic or equivalent. Material: SS or Brass

Supply and fixing of Air shooter Nozzles with Gindal B Class Header, suitable for water effect to achieve height of 15-25 ft. height. Nozzle Specification :- Bronze / Gunmetal / Brass Fine quality Shine chrome made on new technology CNC Cutting. Approx Size 1 Inch,, Thread Size 1/8"BSPT Make : Universal/Premier/Deep n Deep/Orient Fountain/Oase/Aquatic or equivalent. Material: SS or Brass

Supply and fixing of Vario Jet Nozzles with Gindal B Class Header, suitable for water effect to achieve height of 15-25 ft. height. Nozzle Specification :- Bronze / Gunmetal / Brass Fine quality Shine chrome made on new technology CNC Cutting. Approx Size 1inch,, Thread Size 1/8"BSPT Make : Universal/Premier/Deep n Deep/Orient Fountain/Oase/Aquatic or equivalent. Material: SS or Brass

Supply and fixing of Colored Jet Nozzles with Gindal B Class Header, suitable for water effect to achieve height of 15-25 ft. height. Nozzle Specification :- Bronze / Gunmetal / Brass Fine quality Shine chrome made on new technology CNC Cutting. Approx Size 1/2 Inch, Orifice Diameter - 1 mm, Thread Size 1/8"BSPT Make : Universal/Premier/Deep n Deep/Orient Fountain/Oase/Aquatic or equivalent. Material: SS or Brass

Supply and fixing of Water peaks Jet Nozzles with Gindal B Class Header, suitable for water effect to achieve height of 15-25 ft. height. Nozzle Specification :- Bronze / Gunmetal / Brass Fine quality Shine chrome made on new technology CNC Cutting. Approx Size 1 Inch, Thread Size 1/8"BSPT Make : Universal/Premier/Deep n Deep/Orient Fountain/Oase/Aquatic or equivalent. Material: SS or Brass

Supply and fixing of Digital legion Nozzles with Gindal B Class Header, suitable for water effect to achieve height of 15-25 ft. height. Nozzle Specification :- Bronze / Gunmetal / Brass Fine quality Shine chrome made on new technology CNC Cutting. Approx Size 1Inch, Thread Size 1/8"BSPT Make : Universal/Premier/Deep n Deep/Orient Fountain/Oase/Aquatic or equivalent. Material: SS or Brass

Supply and fixing of Water Curtain/Screen nozzle with Gindal B Class Hader, suitable for water effect to achieve dimension 27m X 9m. Nozzle Specification :- Bronze / Gunmetal / Brass Fine quality Shine chrome made on new technology CNC Cutting. Approx Size 1/2 Inch, Orifice Diameter - 1 mm, Thread Size 3/4"BSPT Make : Universal/Premier/Deep n Deep/Orient Fountain/Oase/Aquatic or equivalent. Material: SS or Brass

Supply and Installation of Fountain Actuators as per direction of Engineer-in-charge. Model #S65-168 Material SS

MECHANICAL FIXTURE

Supply and Installation of floating System Structure for fountains as per direction on Engineer -in-charge Material: Mild Steel or Galvonized iron Diameter: 15 inch MS/GI tubeler pipe sealed along all sides to maintain buoyancy of the fountain and ensure to provide a stable platform and safety to main fountain. Coating: Fiber Coated Finish: Black Marine Paint Accessories: Metal flanges, T joint, Elbow joint. End plate dimension 10X30m Double Perimeter

SITC of Fountain support structure for 50mm dia seemless pipe, with cutting drilling tapping and brazing of nozzel base as per design. Coating: Fiber Coated Finish: Black Marine Paint Accessories: Metal flanges, T joint, Elbow joint. End plate Size- 81X16m

Supply and Installation of Plumbing system with specifications mentioned below and as per direction of Engineer-in-charge. Coating: Fiber Coated Finish: Black Marine Paint Accessories: Metal flanges, T joint, Elbow joint. End plate PVC pipe with 5mm thickness of 150mm diameter

Supply installation of 3HP vertical Pump Set or similar suitable for 50 HZ AC supply as per direction, instruction and entire satisfaction of Engineer - in - charge. Type: vertical motor Capacity : 3 HP Three Phase Discharge 30 CBM/hr Head 16 Mtr Suction & Delivery 65 X 65 mm

Supply installation of 4HP vertical Pump Set or similar suitable for 50 HZ AC supply as per direction, instruction and entire satisfaction of Engineer - in - charge. Type: vertical motor Capacity : 4 HP Three Phase Discharge 27 LPS Head 22 Mtr Suction & Delivery 100 X 100 mm

Supply installation of 12.5HP vertical Pump Set or similar suitable for 50 HZ AC supply as per direction, instruction and entire satisfaction of Engineer - in - charge. Type: vertical motor Capacity : 12.5 HP Three Phase Discharge 96 CBM/hr Head 26 Mtr Suction & Delivery 100 X 100 mm

Supply installation of 15HP vertical Pump Set or similar suitable for 50 HZ AC supply as per direction, instruction and entire satisfaction of Engineer - in - charge. Type: vertical motor Capacity : 15 HP Three Phase Discharge 75 CBM/hr Head 46 Mtr Suction & Delivery 100 X 100 mm

Supply installation of 50HP vertical Pump Set or similar suitable for 50 HZ AC supply as per direction, instruction and entire satisfaction of Engineer - in - charge. Type: vertical motor Capacity : 50 HP Three Phase Discharge 128 CBM/hr Head 105 Mtr Suction & Delivery 150 X 150 mm

Air Compressor

Supply installation testing and commissioning of Air Compressor of below specs or similar Suitable for three phase 50 HZ AC supply as per direction, instruction and entire satisfaction of Engineer - in - charge. 50HP/37KW Oil injected screw air compressor with Pre-Filter and Post-Filter

Low Pressure Dryer Capacity: 300CFM min

Air Receiver 2000L /Hr.with all required accessories

ELECTRICAL WORK

Supply & fixing water proof high power LED lights 9 X 3 = 27 Watts LED LIGHTS 27W Type: Beam Lights Input Voltage(V): AC 85-265V Operation mode: Slave/dmx512/sound Active/wireless Dmx Total Power: 27-30w IP Rating: IP52

Supply and Installation of Electrical Cabinet with specifications mentioned below and as per direction of Engineer-in-charge. Dimension: 800x600x2200mm Material: MS poweder coated

Supply and Installation of Electrical Cabinet with specifications mentioned below and as per direction of Engineer-in-charge. Dimension: 30x60x1500mm min Material: MS poweder coated

Supply and Installation of 55KW VFD for motor with specifications mentioned below and as per direction of Engineer-in-charge.Power Rating: 55KW Make: L & T 3 Phase 415V IP21 Digital Display

Supply and Installation of 15KW VFD for motor with specifications mentioned below and as per direction of Engineer-in-charge. Power Rating: 15KW Make: L & T 3 Phase 415V IP21 Digital Display

Supply and Installation of 4KW VFD for motor with specifications mentioned below and as per direction of Engineer-in-charge. Power Rating: 4KW Make: L & T 3 Phase 415V IP21 Digital Display

Supply and Installation of Marine Cable with specifications mentioned below and as per direction of Engineer-in-charge. Coductor material: copper No of Core:3 Core Guage: 4sq.mm Insulation: Rubber compound Type 3GI3 Armour: Steel wire braid over the second inner sheath Inner Sheath: Rubber compound Type GM1b Outer Sheath: Rubber compound Type 5GM3 5GM5

Supply and Installation of Video Surveillance System (CCTV) with specifications mentioned below and as per direction of Engineer-in-charge. Camera Make : CP Plus or Simillar NVR Make : Decklink or Simillar Cables : Dlink or Simillar HDD : WD / Segate or Simillar

Supply and Installation of DMX Console as per direction of Engineer-in-charge. Brand : Chauvet / Philips or Simillar Channels : 1024

Supply and fixing of musical fountain control unit, incorporated with relays and indicator for proper operation of fountain in accordance with music. DMX interface RS232 communication 200Channel Make : Custom Built

Supply and fixing of Digital motor Controller with specifications mentioned below and as per direction of Engineer-in-charge. DMX Controlled RS232/I2C communication Capacity 10A

Supply and fixing of Chasing Jet controller unit with specifications mentioned below and as per direction of Engineer-in-charge. DMX Controlled RS232/I2C communication Capacity 5A PCB mounted

Supply and installation of Solenoid valve for fountains nozzles with specifications mentioned below and as per direction of Engineer-in-charge Material: stainless steel DMX controlled perssure: 10Bars

Supply and installation of Pressure valve for Air shooter nozzle with specifications mentioned below and as per direction of Engineer-in-charge Material: stainless steel DMX controlled perssure: 150psi

Filteration Equipments

Filter Vertical Type Totally anticorrosive imported filter 2.0 diameter manufactured with fibreglass and polyester and resin fitted with collector arm and diffuser made from and plus decide PVC and poly propylene. Filter supplied completely with lead in polyester resin and fiber glass, manual Air purge for sand discharge and PVC flange connection for inlet and outlet complete with necessary pressure gauge.

Filter media: silica sand or white quads for filter with granules of size between 0.4 to 0.8 MM

granules for filter with granules size between 1MM to 2MM

Frontal piping and valve: 160 MM diameter PVC frontal piping and fitting comprising bends, T's , for filter including valve batteries. 150 MM diameter wall for inlet, Outlet, Ab wash, wash out, rinse, with flanges supports wherever required etc.

Circulating pump set: pump set at about 12 m head rated voltage 415 V. Both motor and pump will be mounted on a common base plate with foundation bolt and nut. Complete scope includes providing and fixing. Suction piping only inside the balancing tank with common header assembly on section of pump. Appropriate foot wall inside the balancing tank, butterfly walls on suction and delivery of pumps as well as non-return walls on pumps

315MM diameter PVC pipe for pump delivery header assembly (within plant room) of 6 KG pressure, with branches of 110MM diameter pipe coming from delivery of pump, comprising of Benz, T's, Flanges tail piece, offsets, nuts, bolts supports etc, Wherever required.

315MM diameter filter water outlet header assembly of 6 KG pressure, with branches of 110MM diameter pipe coming from delivery of pump, comprising of Benz, T's, Flanges tail piece, offsets, nuts, bolts supports etc, Wherever required.

315MM diameter filter water inlet header assembly of 6 KG pressure, with branches of 110MM diameter pipe coming from delivery of pump, comprising of Benz, T's, Flanges tail piece, offsets, nuts, bolts supports etc, Wherever required.

Piping network inside of reserve wire tank comprising of 110 MM diameter along with nozzles for circulation of water. Scope includes piping from plant room to shallow end of tank

300 MM diameter wall get operated body. Disc: epoxy coated or EN plated Seat: Nitril rubber bonded on bakelite hard back shaft

300mm dia NRV valve gear operated

LED and Laser

Supply & fixing water proof high power LED lights 9 X 3 = 27 Watts LED LIGHTS 27W Type: Beam Lights Input Voltage(V): AC 85-265V Operation mode: Slave/dmx512/sound Active/wireless Dmx Total Power: 27-30w IP Rating: IP52

15WRGB Laser Emitting Color: RGB Modulation: Analog 50KHZ Input Voltage(V): AC110-240V Total Output: 27000 - 28000 mW Control: ILDA in (Differential) , ILDA out IP Rating: IP52

10WGreen Laser Emitting Color: Green Modulation: Analog 50KHZ Input Voltage(V): AC110-240V Total Output: 27000 - 28000 mW Control: ILDA in (Differential) , ILDA out IP Rating: IP52

Laser Optical Transceiver Signal: DVB-SSI and other Telecom/Datacom rate (19.4Mb/s - 1.485Gb/s) Rise/ fall time: 200Ps nominal Communication: RS232,RS-485, RS422 (full/half duplex) and support NRZ, RZI and Manchester connector: FC/PC(ST/PC optional)

Optical Fiber Fiber Type: G652D Strength member: Steel wire Jacket: LSZH PE

Power Cable connector XLR jacket: PVC Sheilded Conductor:Nickel Plated

Supply and Installation of DMX Console as per direction of Engineer-in-charge. Brand : Chauvet / Philips or Simillar Channels : 1024

MISCELLANEOUS

Software Programming Generate control signal for DMX to operate Individual Solenoid for nozzle Generate control signal for DMX to operate individual Pressure valve for Nozzles Generate control signal for DMX to operate VFD Generate control signal for DMX to operate LED light Generate control for projector Create a system to map all four projector Create a system to run projector in sync with nozzles

4k Video content : These will be Ultra high Defination Content Specifically Converted in the required format, It will be played on multiple projectors arranged in stack to create a synced and immersive experience.

Laser Software Communicate with main software and generate control signal for DMX to operate laser light

"Software Programming Generate control signal for DMX to operate Individual Solenoid for nozzle Generate control signal for DMX to operate VFD Generate control signal for DMX to operate LED light

Electrical Work

Supply,Erection,Testing and Commissioning of Garden speakerwith frequency response: 85 Hz to 20 KHz +/-5 db, sensitivity- 89 db//w/m power handling: 30w RMS, Impedance: 8 ohms, nominal.Drivers: glass filled Polycroplene basket 6.5" Polypropylene woofer, Polycone 1" Tweeter, weather handling: 38 degree C to 60 degree C, Body material: Lexan Polycorbonate Plastic, Coverage pattern: 360 degree Omni directional, similar to garden speak 50 of Ahuja Audio or its equivalents.

Supply,Erection,Testing and Commissioning of Professional Amlpifier Equivalents to SPA-15000 Ahuja make 1500 watts high power PA Amplifier.

Supplying and erecting Junction box for speaker

S & E Loud Speaker cable 4 Core 2.5 sqmm copper multistrand conductor shielded HiFi application cable conduit system

Supplying and erecting professional Ahuja fmx106dp with usb and bluetooth aux in mic in

Supplying & Erecting SS Rack Enclousure for music System

Providing earthing with Galvanized cast iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification No. EA-EP

Supply, installation, testing & commissioning of 4MP IP Dome/Bullet Camera with 1/2.8", progressive scan, CMOS ,2.8/4/6mm lens@ F1.8, ,angle of view more than 82° ,Illumination Colour: 0.02 Lux (F1.8), 0.0Lux with IR ,Day/Night with auto switch ICR, , supported H.264,MJPEG video compression , Smart function supported ( motion , IP67,CE, ROHS.

Supplying, installation, testing and commissioning of 4.0 MP full HD video resolution 2560x 1440, 25 fps True D/N IR Bullet / Box camera, 2.8-12 mm motorised lens, Auto Back Focus, High Light compensation, 120 dB and above True WDR, audio capture capability, 3 streams, H.264/H.265, ONVIF compliant, SD card Slot, with IP67 housing with accessories such as mounting brackets/structures fixtures etc. necessary to mount the camera on pole, etc. Video coding H.264 / H.265, Certification from EN, &CE,FCC.

Supply Installation Testing & commissioning Of Network Video Recorder 32 channel input,Support HDMI Provision for 4 SATA HDDs, Up to 8TB for each HDD, HDMI/VGA Output, Recording Resolution, 6MP/5MP/4MP/3MP/1080p/960p/ 720p/D1/2CIF/ CIF, Compression H.265/H.264.

Supply , Installation, Testing & Commissioning of UTP Connector (RJ-45) as per specification No. WG-AS/UTPC.

Supply Installation Testing & commissioning of 8000 GB Hard Disk for video Surveillance Equivalent to:- Western Digital./Seagate

Supplying, fixing, and configuring 8-ports Managed Gigabit Switches Layer-2, 10/100/1000 Base-T PoE Smart Switch plus 2 SFP only (New).

Supply Installation Testing & commissioning of 32" LED TV Monitor Equivalent to:- LG/Samsung

SITC of pole mounted type Outdoor junction Box along with pole mounting accessories, and for equipment mounting suitable for accomodating ,Electrical switch unit, UPS, Media Converter and POE switch, as directed by Engineer In Charge.

Supplying and fixing 6U Wall Mount Rack (Dimension-DxWXH - 450X550X367 mm) as per specification in approved manner

SFP Module For Optic Fibre Connectivity

SITC of 600 VA UPS for backup during power failure.

Supplying & installing UTP networking cat-6 armoured cable suitable for LAN / WAN Computer net-working as per specification No. WG-COC/NC

Supplying & installing single mode OS1/OS2 - armoured – 6 core OS1/OS2 armoured single mode optical fibre of size 50/125µm. 10/40 gbps speed in provided underground HDPE pipe complete.

Supplying and erecting ISI mark G.I. pipe pole ‘B’ grade 80 mm dia 6 m long with pole cap, base plate in provided foundation as per specification no. OH-PL/GIP

Providing PU paint to G.I./octagonal poles as required of desired colour duly finished in an approved manner for 6 mtr long pole including Bracket

Making cement concrete foundation including excavation ( 45 x 45 x 120 ) cm deep in 1:3:6 cement concrete, 20 to 25 mm stone metal, (45 x 45 x 45) cm / 45 cm dia. x 45 cm height plinth duly plastered, with necessary curing and finishing complete. (for 6 m pole)

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by

Providing and maintaining temporary 1 KVA on line UPS pure sine wave suitable for 30 minutes battery backup to provided computer with necessary interconnecting cabling, wiring etc for three days.

DISCOM MSEB/TORRENT Charges for Lights/Sound/CCTV

SITC of 3.5 mtr long GI pole with double Decorative bracket arm. The pole shall have flush door & locking arrangement at the bottom of pole. The pole door shall be attached to the pole with rope wire . The pole shall be made out of bottom pipe of 139.7 mm dia and 4 mm thick with base plate . Top section of 76.1 mm dia having thickness 3 mm The pole shall be provided with decorative Aluminium/CI embellishments to add aesthetics to the pole .The bracket is of 48.3 mm dia. and having decorative design as per drawing attached. The body of decorative pole shall be machined and polished properly to give it a smooth surface. The double arm bracket shall have a span of 800 mm with design in the middle made of 8mm rod with flower and leaf design with arrangement for placing fixture in post top position. The pole shall be made of galvanized iron pipe and base plate of 250 x 250 with 10 mm thickness. The pole shall be painted with PU paint with one coat of etch primer , one coat of zinc phosphate primer with a thickness of 60 microns. Color : Matt black and Gold.The decorative pole shall be duly pre treated and painted in U V ray resistant PU coating in approved colour shade with provision of terminiation box in the base compartment complete in all respect. The shape and the final design shall be got approved from engineer in charge

SITC of 3.5 mtr hot dipped galvnised and PU painted Cartoon Character Pole with 1 mtr bottom made up of 139 mm OD GI pipe and 2.5 mtr top made up of 76 OD GI pipe. Baseplate shall be minimum 250 x 250 x 10 mm in size and hot dipped galvanised. Entire pole shall be painted with desired color shade of MRF make PU paint after etch and gray primer coats. (This price does not include any lights, Camera, Speaker or electrical components.)

SITC of 3 mtr hot dipped galvnised and PU painted petal pole made up of 139 mm OD GI pipe for trunk and 48 OD GI pipe for branches. Petal shall be made up of FRP/GI metal sheet. Baseplate shall be minimum 250 x 250 x 16 mm in size and hot dipped galvanised. Entire pole shall be painted with desired color shade of MRF make PU paint after etch and gray primer coats. The Pole shall be with 40W indirect LED fitting with IP65 . Proper Heat dessipation shall be made as per specifications.

Providing & erecting 7 m high galvanised octagonal pole with bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/PSC

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity as 10 T/sq.m at 1.5 m depth including supply of steel, concrete,excavation, fixing provided nut bolts with the help of template, duly plastered as per design complete (for 3 to 5m octagonal / conical GI pole).

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel,concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole).

Supplying and erecting pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. strip complete with all materials as per specification no. EA-EP

Supply of decorative luminaire made of spun aluminium body with pressure die-cast heat management (PDCHM) and the IP65 optical compartment with high power LED/s is comprised of a deep drawn chemically polished and co-extruded, thermofrmed ploycarbonate protector stabilized agent UV rays suitable for 40W LED. Fitting should be post top mounting type decorative fixture. fitting should have decorative elements to be placed on top of the ficture for asthetic purpose. Fitting should have inbuilt driver with efficiency >0.9 and having surge protection device of 4KVA and external surge protection device of 10KVA, colour temperature 3000K / 4000K / 5700K Natural day light LED.LED's to be of Osram / Cree / Bridgelux & driver to be of make Philips / fulham / Osram.

SITC of Decorative hanging type LED decorative light fitting made of Alum Die Cast – 60W/70W, with pressure die-cast heat management (PDCHM) and the IP65 optical compartment with high power LED/s , colour temp shall be 4000k with permissible tolerance .Fitting should have inbuilt driver with efficiency >0.9 and having surge protection device of 4KVA and external surge protection device of 10KVA, colour temperature 3000K / 4000K / 5700K Natural day light LED.LED's to be of Osram / Cree / Bridgelux & driver to be of make Philips / fulham / Osram.

Supply Installation Testing & commissioning of integral high pressure Die cast/extruded aluminium LED Floodlight luminaire with proper heat dessipation & toughned glass protector or with yellowing injection molded polycarbonate cover having high light transmission index.The LEDs are provided with suitable lens for dispersal for achieving street light optics to ensure uniform light distribution.The LED fixture shall be desighned for at least L70 life of minimum 50,000 burning hours at ambient tempreture not less than 35*C. the system wattage (fixture's total power consumption) should be be 120W. Details as per technical specification attached.

Supplying and erecting Recess mounted 30W LED wall washers, tilted 70° outwards and swivels 360° to offer best illumination on the wall with any colour with driver complete. ( Including Compatible Driver)

Providing and erecting 36W Mono colour Façade lighting with IP66 rating with beam angel variation possibility as directed by engineer incharge,equivalent to Leksa, Bajaj, Philips, Crompton

Supply and erection of Hot dip galvanized Ring for installation of mini high mast suitable for 4 Nos of LED Flood lights. The outer dia of ring shall be 600 mm. The ring shall be of 50 mm dia B class pipe with three supports to Sleeve, the sleeve shall be of 500 mm length and 4 mm thick duly provision of 4 nos bols and shall be suitable to fit on Octagonal pole of 70 mm AF

Supplying and erecting LED flexible strip light 5m length upto 25W conforming IP 65 of any colour with driver complete.

Supplying & erecting mains with 3x2.5 Sq.mm F.R stranded/solid copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG- MA/BW

Providing PU paint to octagonal poles as required of desired colour duly finished in an approved manner for 7 mtr long pole

Providing PU paint / Powder coating as required of desired colour duly finished in an approved manner for 600 mm dia. Mini highmast ring

Supplying and erecting regular/ standard model ceiling fan of 1200mm. sweep complete erected in position as per specification.

Supplying and erecting modular type electronic step regulator two module ISI mark approved make duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ‘B’ grade G.I. pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire.

Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying and erecting fresh air cum exhaust fan light duty 250 V, A.C. 50 cycles225 mm. 1400 RPM rust proof body & blades,wire mesh duly erected in approved manner

Supplying & erecting LED 20W tube light fitting (4 feet) with battern type, heat sink, integrated HF electronic driver complete.

Supplying, erecting & terminating XLPE armoured cable 4 core 25 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB LT/AL

Supply, Installation, Testing and commissioning of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete. Specification no.EA-MOBI

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with insulating and non-corrosive bond in an approved manner with required joints As per specification no. EAEP.

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Supplying and erecting modular type switch 6A / 10A ISI mark approved make duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16A ISI mark approved make duly erected on provided plate and box with wiring connections complete

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter ISI mark approved make duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 16A multi socket with safety shutter ISI mark approved make duly erected on provided plate and box with wiring connections complete.

Supplying and erecting PVC Surface modular double mounting plate 6 module complete duly erected in an approved manner

Supplying and erecting PVC Surface modular double mounting plate 8 module complete duly erected in an approved manner

Point wiring in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FR grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Point wiring for independent plug in PVC trunking (casing capping) with 1.5 sq.mm (2+1E ) FR grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification No. SWSWR/MCB

Supplying, erecting & marking DPMCB 6 Amp to 32 Amp in provided distribution board as per specification no. SW- SWR/MCB

S/E CRCA sheet metal one way enclosure suitable for DPMCB / TPMCB /FPMCB complete erected on angle iron frame .

Supplying & erecting mains with 3x4 sq.mm F.R copper PVC insulated wirelaid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying, erecting & terminating XLPE armoured cable 4 core 10 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/pole or laid in provided trench/ pipe as per specification no.CB-LT/AL

Supplying and laying (including excavation) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Providing M20 concrete for resurfacing the road.

Supplying, erecting & marking SPMCB 0.5A to 5A in provided distribution board as per specification no.CB-SB

Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification No. SWSWR/MCB

Supplying, erecting & marking SPMCB 40A to 63A, B- series (for lighting) in provided distribution board as per specification No. SWSWR/MCB

Supplying and erecting bakelite sheet 6 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners supports, nuts bolts etc. complete.

Supplying and erecting enamel iron G.I. sheet 1.6mm (16 gauge) caution board of size 200 x150 mm. as per I.S. 2551 of 1982 in Marathi and Hindi erected at position for medium installation.

Supplying & erecting mains with 2x10 sq.mm F.R copper PVC insulated wirelaid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying & erecting Single Pole Bakellite 35 Sqmm connector for connecting wire from MCB to cable

MCB/RCCB Channel Support patti

Supplying & erecting approved make 415V 63A porcelain base neutral link complete erected in provided M.S. box.

Supplying and erecting metal work in CRCA sheet including Iron work for supports with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete

Providing cement concrete for foundation or for concrete filling in 1:3:6 ratio with 20 to 25 mm. stone metal duly plastered with necessary curing for pole muffing or any other purposes.

Supplying and erecting 4 pole power contactor 440V 40A for time switch complete erected on wooden block/provided box, with necessary materials.

Supplying & erecting crimping type copper lugs for cable upto 16 sq mmcomplete as per specification No. CB-L/CU

SITC of nature switch infrared for making ON/OFF street light as sun set and sun rise. The nature switch shall be housed in FRP casing with protection of MCB opening voltage 150V to 300V 30-60 Hz

Supplying and erecting bulkhead fitting suitable for upto LED upto 12W fixed on wall. As per specification no.FG-IDF/BHF

Supplying & erecting 5 - 7 W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying and erecting PVC trunking (PVC casing-n capping) of size 25 mm with accessories on wall/ceiling as per specification No: WG-MA/CON.

Supplying and erecting HMS PVC conduit 25 mm dia.with PVC accessories on wall /ceiling as per specification No: WG-MA/CON.

Supplying and fixing wiremesh (Jali) cover suitable for fitting / fan or for any purpose ,complete with necessary materials. The Jali cover shall be made from good quality G.I. wire mesh size 25 mm x 25 mm and made up of 14 SWG G.I. wire with side / supporting MS strips of suitable size.

GARDEN DEVELOPMENT WORK

Excavation for foundation in earth, soil of all types, sand, grave lands of murum, including removing the excavated material upto adistance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc.complete.(Liftupto 1.5 m.) By Mechanical Means

GARDEN SOIL :- Supplying on site garden soil well sieved 90% to pass through I.S. sieve of 10mm size Free from stones rubbish like dried grass roots and other such materials. The soil should be fresh be measured by measuring box (Farma) Item includes royalty charges, octroi, corporation Tax Transporting, loading – unloading etc

As derected by Engineer-Incharge.

Farm yard manure :- Supplying on site well decayed, well dried, well powedered, withought clods and free from stones, dried grass and other rubbish material,. The colour of the manure generally be black. the manure will be measuring by measure box. (farma) item includes Transporting, loading -unloading etc (lead charges per 40km. are considered.

As derected by Engineer-Incharge.

Preparing Instant Lawn : Excavating the ground to a required depth of 20cms removing & conveying unwanted stuff to a required distance as directed. filling fresh garden soil / silt & manure in excavated area in 3:1 proportion to a height of 20cms. Mixing garden soil and manure thoroughly will levelling, watering on previous night. Planting required variety of lawn grass as directed and maintaining till well established by watering weeding clopping rolling etc. complete

As derected by Engineer-Incharge.

Preparing Shrubbery :- Excavating the round to required depth of 30cms, removing and conveying unwanted stuff to a required excavated area in 3:1 proportion to a height of 30cms. Mixing garden soil & manure toughly well, leveling , watering on previous As derected by Engineer-Incharge.

As derected by Engineer-Incharge.

Supplyings & planting of plants required for landscaping:- Euphorbia, hemelia, Malphejia, Ticoma, song of India, Golden bamboo, Bhudhhaj bamboo, golden ficus, Phonicu palm, x mass trees ficus panda, etc. (height of plant 5-6 ft )

As derected by Engineer-Incharge.

Planting large flowering / shady trees :- Digging pit with size 0.9m x 0.9m x 0.9m removing and conveying unwanted stuff to a required distance as directed. Filling the pit with approved excavated material upto a height of 0.30m and remaining height of 0.60m with fresh garden soil & manure in 3:1 proportion Mixing soil & manure thoroughly well. leveling as directed, watering previous night, planting on to two year old healthy trees sapling as per specifications. Maintaining till well established by watering weeding, stirring of soil replacing of casualties etc. complete.

As derected by Engineer-Incharge.

Providing forest trees putranjiva, jaccaranda, bakula, kecia, Neem, shoka Gulmohar 8 feet to 10 feet.

As derected by Engineer-Incharge.

Providing and supplying palm trees vaieties, red palm, fox tail palm, botttol palm, Rhaphis palm, Table palm, Cristle palm, cene palm, Ashoka etc.. Size 10-12 feet

Skyway Infraprojects Pvt. Ltd.