REPAIR / MAINT OF CEILING FAN / EXHAUST FAN / WALL FAN INCLUDING DAY TO DAY COMPLAINT OF INTERNAL ELECT AT NAMS.

Amount

Attending of day to day electrical complaints pertaining to internal electrification received through telephone/ Armaan or in person on detailment at MES Service centre located at NAMS Area by locating and rectification of fault from and including electric meter/DB onwards in respect of sub main/point wiring including provisioning of small pieces of electric cable of size 1.5/2.5 Sqmm to 10 Sqmm single core copper conductor and length not increasing 0.50 mtrs and fixtures for power and light socket/light, fan and bell etc complete and carrying out repairs to the extent of tightening of loose connections, disconnection and dismantling of faulty wires, battens, conduits, boxes, main switches, MCB's, DB's and other E/M fixtures including providing necessary screws / nuts / bolts / nails for the rectification of defect and refixing of existing dismantled serviceable items and replacement of defective items with new ones complete all as specified and directed. Note - (i) Cost of labour for the fixing/replacement of unserviceable item shall deemed to be included in item no 2 and cost of store replaced shall be measured as supply only against relevant Items. (ii) Complaint pertaining to location and rectification of fault in more than one length of point wiring/sub main wiring/DB's/fitting or fixtures etc shall be considered as an independent complaint. Similarly complaint pertaining to replacement of two fixtures in one Qtr will also be measured and paid as one complaint.

(iii) Replacement of more than two fixtures/items but multiple of three fixtures or part thereof in one Qtr/Bldg will be measured as an additional complaint. (iv) In case a Qtr/room is found locked when tradesman is detailed to attend the complaint, the complaint shall be treated as one till its completion. (v) Necessary tools for tradesman shall be provided by the contractor. (vi) Transportation for tradesman and normal stores required for complaints shall be arranged by the contractor. (vii) Complaints of normal nature shall be attended and rectified within 8Hrs of receipt of complaint. However, complaints of emergent nature i.e no light, short circuit, earth fault etc shall be attended immediately on receipt of complaint round the clock. (viii)Bldgs requiring rewiring of small qty of point wiring if ordered will be measured and paid separately under respective items below (ix) Contractor will deposit all the items to EM Store in advance and unsv items will be collected by the contractor as schedule of credit (x) Electrician will report to AGE EM complaint cell at 9 O'Clock daily for collecting of complaints. Complaint received on Armaan application will be done in the same day and after completion of complaint Electrician will report to Armaan Cell for uploading the completion report. (xi) Contractor deploy local electrician for the job so that urgent nature of complaint like no light, short circuit and earth fault will also done on Holidays/ Sunday.

Supply only in replacement switch piano flush type 5 Amps One-way, AC 230V on existing switch board all as specified and as directed.

Supply only in replacement of switch piano flush type 15 Amps single pole one-way, 230V complete all as specified and as directed.

Supply only in replacement switch piano type two ways AC 230 volts 6 Amps as per on existing switch board .

Supply only in replacement socket out let 2-in-1, 3 Pin 5 Amps flush type 230 volts complete all as specified and as directed.

Supply only in replacement socket outlet, flush type, 2-in-1, 3 pins, 5 & 15 Amps multipurpose complete all as specified and as directed.

Supply only in replacement bell push switch piano, flush type, 5 Amps complete all as specified and as directed.

Supply only in replacement of bell ding-dong 230 volts, single phase complete all as specified and as directed.

Supply only in replacement of ceiling rose 65x50mm two to three terminals AC 230 volts complete all as specified and directed of any make/model as per in existing building.

Supply only in replacement roter type Bipin holder of any size/shape as required at site for 20/28/40 watts tube light 240 Volts complete all as specified and as directed.

Supply only in replacement batten type angular/ Battan lamp holder insulated body with back plate suitable for batten fitting including PVC round block complete all as specifed and as directed.

Supply only in replacement LED out door drivers 25W suitable for security light 25 watt, AC 230V complete all as specified and as directed.

S&F in replacement MCBs single pole 5 to 32 Amps with 10 KA breaking capacity of 'C' series in distribution boards all as specified.

S&F in replacement MCBs single pole and neutral 40 Amps with 10 KA breaking capacity of 'C' series in distribution boards all as specified and directed.

S&F in replacement MCBs single pole and neutral 63 Amps with 10 KA breaking capacity of 'C' series in distribution boards all as specified and directed.

Supply only in replacement of single pole and neutral sheet metal enclosures with two pin & earth plug and socket complete with one single pole MCB of 20 Amps complete all as specified and as directed.

Supply only in replacement plug top 3 pin, 5 Amps complete all as specified and as directed.

Supply only in replacement plug top 3 pin, 15 Amps complete all as specified and as directed.

S&F in replacement Electronic Ballast (P.F 0.9), 230v, 50HZ, 36 watt complete all as specified.

S&F in replacement fluorescent tube light rod 4 feet long of capacity 36 watt all as as directed by Engr-in-Charge.

S&F in replacement LED bulb of capacity 5 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S&F in replacement LED bulb of capacity 7 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S&F in replacement LED bulb of capacity 9 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S&F in replacement LED bulb of capacity 12 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S&F in replacement LED bulb of capacity 15 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S&F in replacement LED Tube rod LED tube rod with polycarbonate diffuser 4 feet long of capacity 18 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S&F in replacement LED Tube rod LED tube rod with polycarbonate diffuser4 feet long of capacity 20 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S&F in replacement LED Tube rod LED tube rod with polycarbonate diffuser4 feet long of capacity 22 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S&F in replacement LED bulb of capacity 9 watts, threaded type suitable for post top lantern complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S&F in Replacement of existing sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 4.0 Sqmm drawing into and including PVC non metallic rigid conduit of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 4.0 Sqmm as a earth continuity conductor(green colour) in and including in non metallic rigid PVC conduit, including cutting chases in brick wall, replastering and making good to match the existing specifications complete all as specified and directed by Engineer-in-Charge. Note :- (i) Rates are deemed to be included chases of conduit and sinking for boxes cutting and making holes in wall/floor for passing in or through conduit (ii) Two run of 4.00 sqmm single core (FRLS) PVC insulated copper conductor cable one run of 4.0 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit.

All as per item 31 here in before but with 2 run of 6.0 Sqmm and one run of 6.0 Sqmm as earth continuity conductor(green colour) complete all as specified & directed.

All as per item 31 here in before but with 2 run of 10.0 Sqmm and one run of 10.0 Sqmm as earth continuity conductor(green colour) complete all as specified & directed.

Supply only in replacement of 12 Watt Square/ Round surface mounted LED Panel down lighter complete all as specified and directed,

Supplying only in replacement LED bulk head light fittings including led lamp 10watt as per IP65 and making necessary connections complete all as specified

Supply only in replacement LED slim panel cygnus series recess/surface/suspended mounting LED slim ceiling light 2'x2' with extruded aluminium housing and milky diffuser, suitable for recess mounted size 595x595mm complete with LED tube complete all as specified and directed.

Supply only in replacement of 6 Watt Round recess mounted down lighter separate replaceable electronic driver celling cut out dia 105 mm height 16 mm round shaped polycarbonate fixture complete all as specified and directed,

Supply only in replacement of 12 Watt Round recess mounted down lighter separate replaceable electronic driver celling cut out dia 160 mm height 16mm round shaped polycarbonate fixture complete all as specified and directed,

Supply only in replacement of 6 Watt Square recess mounted down lighter separate replaceable electronic driver celling cut out 104mm x 104mm height 30mm square shaped polycarbonate fixture complete all as specified and directed,

Supply only in replacement of 15 watt Square recess mounted down lighter separate replaceable electronic driver celling cut out 155mm x 155mm height 32mm square shaped polycarbonate fixture complete all as specified and directed,

Supply only in replacemnt box type PVC rectangular block for mounting switches, sockets, fan regulator etc 4/6 way, surface mounting complete all as specified and as directed.

Supply only in replacement of frame plate for modular switch 4 module including screws and washers etc model/make as per existing in site complete all as specified and as directed.

Supply only in replacement of frame plate for modular switch 8 module including screws and washers etc model/make as per existing in site complete all as specified and as directed.

Supply & Fix in replacment High bay light 120 watt with high power SMD LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base pole adapter, pressure die cast LM6 diffusor:injection model polycarbonate, powdre coated in IP 66 Incliding protection over temperature.

Supply only in replacement modular ceiling fan regulator, electronic Socket type, single phase, 230 volts complete all as specified and as directed.

Supply only in replacement ceiling fan regulator, electronic switch type, single phase, 230 volts complete all as specified and as directed.

Supply only in replacement MS machine screw 25 mm long suitable for fixing bakelite hylam sheets / square blocks complete all as specified and directed .

Supply only in replacement MS Housing box 5/6 module suitable for modular switch as per existing including taking out old UNSV switch box and making good to the disturb surface by pcc complete all as specified and as directed.

Supply only in replacement of MCCB 100 amps , AC 415 volts 16 KA, Three pole including making connections with suitable size of aluminium lugs of any make /Model as per Existing MCCB Fitted in DB. all as specified.

Supply only in replacement of modular switch 5/6 Amps one module 230 volts AC as per existing model/make complete all as specified and as directed

Supply only in replacement of modular switch 15/16 Amps one module 230 volts AC as per existing model/make complete all as specified and as directed

Supply only in replacement of modular socket, 5/6A -2/3 pin combined 2 module, 230 volts AC as per existing model/make complete all as specified and as directed.

Supply only in replacement of modular socket, 15/16A -2/3 pin combined 2 module, 230 volts AC as per existing model/make complete all as specified and as directed .

Supply only in replacement modular fan regulator, 2 Module/1 module , 4 step heavy duty 230 volts as per existing model/make complete all as specified and as directed.

Supply only in replacement of capacitor AC 230 volts 2.25 MFD complete all as specified and directed.

Supply only in replacement of capacitor AC 230 volts 3.15 MFD complete all as specified and directed.

Supply only in replacement of 3mm thick hylam sheet of any size including screws and washers etc as per required at site complete all as specified and as directed.

Supply only in replacement moduler bell push switch piano, flush type, 6 Amps complete all as specified and as directed.

Supply only in replacement of 12 Watt Square recess mounted down lighter separate replaceable electronic driver celling cut out dia 160 mm height 16mm round shaped polycarbonate fixture complete all as specified and directed.

Supply only in replacement tuggle switch for amination depot complete all as specified and as directed.

S&F in replacement LED tube light fitting. ,1x20w, 230v Energy efficient T8, Box type made of CRCA shee heavy duty industrial type housing with reflector cover channel, bipin holders, connector block, etc. complete with tube rod LED 20 watt, all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

S&F in LED mirror fitting. 1x8w, 230v Energy efficient , Box type, housing with reflector cover channel, bipin holders, connector block, etc. complete with tube rod LED 8 watt, all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

Supply and fixing bed light fancy type,10watt with lamp complete all as specified and directed.

Supply only in replacement of single core wire 2.5 Sqmm multi-strand PVC insulated copper conductor FRLS cable including connections of cable with MCBs or bus bars complete all as specified and directed.

Supply only in replacement of single core wire 1.5 Sqmm multi-strand PVC insulated copper conductor FRLS cable including connections of cable with MCBs or bus bars complete all as specified and directed.

Material and labour for point wiring with 1.5 Sqmm multi strand pvc insulated copper conductor cable in existing concealed conduit for one light or bell point controlled by one switch including pvc insulated 1.5 sqmm copper conductor continuous earth wire using existing CI/MS sunken box and connecting earth with dolly complete all as specified and directed. ( Note : Switch, socket measured as separate item )

All as per item No 66 here in before but for one 5 Amps independent board complete

All as per srl item No. 66 here in before but for one 5 amps socket out but on the same board complete

Matrial and labour for point wiring with 2.5 sqmm multi strand pvc insulated copper conductor cable in existing concealed conduit for one 15 amps socket outlet independent controlled by one switch including pvc insulated 2.5 sqmm copper conductor continuous earth wire connecting earth with dolly complete all as specified and directed.

Supply & fix in replacement of building security LED Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens complete all as specified.

Supply and fix in repair GI pipe bracket ,made out of GI pipe 50mm dia light grade 1.2mtr long bend to the shape 120 degrees angle complete with two nos of clamps for fixing on walls complete all as specified and directed.

Taking down Exhaust Fan of any make & size from existing position of any height for repair, mainteance and refixing the same after neccesary repair complete all as directed. Notes (i) The defective parts to be replaced shall be measured and paid separately under relevant item of Sch . (ii) Cost of minor items i.e. Screws, nut & bolts etc shall be deemed to be included in the above item.

S&F in replacement double ball bearing (ISI marked) for exhaust fan of 450mm sweep capacities complete all as specified and directed.

S&F in replacement double ball bearing (ISI marked) for exhaust fan of 300mm sweep capacities complete all as specified and directed.

S&F in replacement Gun metal bush for Exhaust fan of any cap/ any size sweep complete complete all as specified and directed.

M&L for removing old burnt winding of exhaust fan 450mm sweep motor and rewinding the same with superior quality super enamelled copper wire of suitable size including insulation ,drying after varnishing complete all as directed and specified by Engr-in- Charge.

M&L for removing old burnt winding of exhaust fan 300mm sweep motor and rewinding the same with superior quality super enamelled copper wire of suitable size including insulation ,drying after varnishing complete all as directed and specified by Engr-in- Charge.

S&F in replacement blade suitable for exhuast fan of 450mm sweep of existing make complete all as directed and specified by Engr-in- Charge.

S&F in replacement blade suitable for exhuast fan of 300mm sweep of existing make complete all as directed and specified by Engr-in- Charge.

S&F in replacement louvers shutter suitable for exhuast fan of 450mm sweep of existing make complete all as directed and specified by Engr-in- Charge.

S&F in replacement louvers shutter suitable for exhuast fan of 300mm sweep of existing make complete all as directed and specified by Engr-in- Charge.

S&F in replacement of capacitor 4 mfd ISI marked complete all as directed.

Taking down ceiling fan of any make & sweep by disconnecting clips,lock nuts etc. from existing position of any height in safe costudy for repair & mainteance. (Note: Repair & Maintance Shall be paid separetly under relevant items.)

Hanging only ceiling fan 1200mm/1400mm sweep after repair & maintenance with existing down rod clips,lock nuts etc. Note:- Refixing of repaired fan in any location of NAMS area with in distance of 4 Km shall be contractors responsiblility at his own arrangement of transport and tool and plant.

M&L for Painting of ceiling fans complete, in situ/lying in store with synthetic enamel paint (white colour) by spraying including filling cavities with filler, one coat after cleaning all dust etc

M&L for removing of old burnt winding of fan any type and rewinding the stator with superior quality super enamelled copper wire of suitable size including insulation ,drying after varnishing complete all as directed and specified by Engr-in- Charge.

S&F in replacement bearing for ceiling fan 1200mm/1400mm sweep ISI marked complete all as specified and directed.

S&F in replacement Gun metal bush for ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

S&F in replacement cup made of plastic complete with nut bolt for fixing in position suitable for ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

S&F in replacement rubber bush/reel for hanging bracket suitable for ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

S&F in replacement blade suitable for 1200mm sweep Ceiling fan complete all as specified and directed.

S&F in replacement blade suitable for 1400mm sweep Ceiling fan complete all as specified and directed.

Supply and Replacement of split pin 40 mm to 50 mm long complete all as specified and directed.

Supply and replacement of steeel screw ( to be used for fixing of fan blades) as per sample /site requirement) complete all as specified and directed.

S&F in replacement 3 core PVC insulated PVC sheathed flexible copper wire multistranded 1.5sqmm from ceiling rose to fan connector complete all as specified and directed.

S&F in replacement of capacitor 2.5 mfd ISI marked complete all as specified and directed.

S&F in replacement of capacitor 3.15 mfd ISI marked complete all as specified and directed.

Taking down and refixing in PVC exhaust fan motor in replacement for 250 mm sweep , 230 volts 50 c/s complete all as specified and directed.

Taking down and refixing PVC exhaust fan blade in replacement for 250mm sweep 230 volts 50 c/s of make bajaj / Havell,s/Crompton all as specified and directed.

Taking down and refixing PVC exhaust Fan body in replacement for 250mmsweep, 230 volts 50 c/s of make bajaj / Havell,s/Crompton all as specified and directed.

M&L for PVC wall mounting fan 400mm sweep, pull chain type, 230v 50 Hz complete all as specified and as directed.

M&L for Padestal fan 400 mm sweep , 230v, 50Hz complete all as specfied and as directed.

M&L for taking down the existing faulty single phase tamper proof Electronic Energy meter with LCD display 230 volts 4 wire system, 10-60 amps, 50 Hz ,replacing the unserviceable chip board, unsv body and all burnt parts complete,making it to serviceable state, including testing, caliberation & refixing the same complete all as specified and directed by Engr-in-Charge.

Supply & fixing in replacement of integral post top lantern complete with black ABC plastic spigot, spun aluminium funnel shape with clear acrylic cover light opening on canopy with baffles and accessories and suitable for LED lamp complete all as specified and directed

Supply and fixing in replacement of sheet metal enlosure for DBs when MCBs to be used double door factory made flush fixed complete with 100 amps rated bus-bar 240 volts single phase 8 ways including necessary brick work and plaster to match with the existing surface complete all as specified.

Supply and fixing in replacement of sheet metal enlosure for DBs when MCBs to be used double door factory made flush fixed complete with 100 amps rated bus-bar 240 volts single phase 12 ways including necessary brick work and plaster to match with the existing surface complete all as specified.

M& labour in replacelment for service wire10 sqmm 2core pvc insulated and pvc sheathested1100 volts grade all as specified and directed

M& labour in replacelment for service wire16 sqmm 2core pvc insulated and pvc sheathested1100 volts grade all as specified and directed

Supply only in replacement LED drivers suitable for 16 watt ceiling light, input voltage 230V AC and output 35V DC, complete all as specified and as directed.

Supply only in replacement LED drivers suitable for 36 watt ceiling light, input voltage 230V AC and output 35V DC, complete all as specified and as directed.

Supply only in replacement LED drivers suitable for 12W watt ceiling light, input voltage 230V AC and output 35V DC, complete all as specified and as directed.

Supply only in replacement LED drivers suitable for 20W watt ceiling light, input voltage 230V AC and output 35V DC, complete all as specified and as directed.

S&F in replacement Electronic Ballast (P.F 0.9), 230v, 50HZ, 28 watt complete all as specified.

CHINAR ENGINEERS AND BUULDERS

M/s AKG Engineers & Contractors

Mahajan Builder

HARPAL ENGINEERS AND BUILDERS

kailu construction co