Up-gradation of Nanikhad to Samleu road km 0/0 to 30/585

Amount

Excavation in hilly areas in all heights and depths and in all kinds of soil by manual/mechanical means including saturated soil comprising of ordinary soil, ordinary rock ,soft rock ,hard rock chiseling, wedging out rock (where blasting is prohibited) and their intermediate classification of soil complete including setting out true to the lines, grades, width, cutting and trimming of side slopes and levels as shown on the drawings and as directed by Engineer-in-Charge at site, according to the MORD technical specification section 300 and 1600 and sorting out useful materials and stacking the same within all leads and lifts in acquired road width and transportation of un-useful materials for filling in roadways camber ,embankments for grade improvements and disposal of all un-useful materials to approved dumping sites through all modes of transportation including head load or animal transport or mechanical means alongwith its leveling fine dressing and carriage of machineries ,materials, tools, equipments and safety measures and other incidentals necessary to complete the work by mechanical means and/ labour if required.All useful materials such as stones, shingle aggregate and slates etcetera shall be sorted out and stacked in proper stack. Recovery of stones to the tune of 20118.22 cubic metre quantity @ Rs. 300/- only ( at the rate of rupees three hundred ) only per cubic metre shall be effected from the contractor’s running bills on pro-rata basis as per actual quantity executed. Any loss to the public/ private property during the course of execution shall be the absolute responsibility of the contractor which shall have to be compensated by him in all cases.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 [ One cement is to four sand is to eight graded crushed stone aggregate 40mm (forty millimetre) nominal size] including pumping or bailing out water (surface and sub soil water) and removal of slush which may arise at the time of laying concrete including the cost of form work and curing complete in Retaining walls and Breast walls etcetera,as per drawings and MORD technical specification sections 800,1200 and 1600 and direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incidentals.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing 100mm (Hundred millimeter) diameter PVC(poly Vinyl chloride) pipe Weep holes in brick masonry/stone masonry, plain/reinforced concrete abutments, wing walls return walls and retaining /breast walls etc., extending through the full width of the structure with slope of 1 (V) : 20 (H) (one vertical is to twenty horizontal ) towards drawing face complete as per drawings and MORD technical specifications clause 709 and 1206.6 or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying of boulder apron gabion wall laid in wire crates with 4mm(four millimetre) dia G.I. wire( Galvanized iron wire) confirming to IS: 280 (IS: two hundred eighty) and IS: 4836 (IS: four thousand eight hundred thirty six) in 100mmx100mm(one hundred millimetre into one hundred millimetre) mesh (woven diagonally) including 10% (ten percent) extra for laps and joints laid with stone boulders weighing not less than 40kg (forty kilogram) each as per drawing and MORD technical specification clause 1301 and as per directions of Engineer-in-charge including the carriage of material within all leads ,lifts and other incidental. The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying Mechanically mixed and vibrated concrete for plain cement concrete nominal mix 1:3:6 ( one cement is to three sand is to six graded crushed stone aggregate 20 millimetre (twenty millimetre nominal size on ground or under water and curing complete for 14 (fourteen) days, in open foundations for all type of structures including pumping or bailing out water (surface and sub soil water) dewatering for all depths and any quantum of water including removal of slush which may arise at the time of laying concrete complete for all heights / depths including the cost of form work complete as per drawings and M.O.R.D. technical specification section 800,900 and 1200 or as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm (six hundred millimetre) with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1203 & 1604 and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Loosening of ground upto a level of 300mm (Three hundred millimetre ) below the sub grade level, watered, graded with motor grade and compacted in layers to meet the requirements of table 300.1 and 300.2 with three wheel 80-100 (eighty to hundred) kN static roller for sub grade construction as per MORD technical specifications clause 303 or as directed by the Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material within all leads and lift as per MORTH Technical Specification Clause 301.4 and as per the directions of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per Technical Specification Clause 303.1. or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Construction of granular sub base by providing well graded materials and spreading in uniform layers with tractor mount appropriate grading arrangements on prepared surface, mixing by mix in place method at OMC with tractor mount appropriate rotavator attachment and compacting with three wheel 80-100 (eighty -one hundred) kN static roller to achieve the desired density, as per MORD Technical Specifications clause 401 for grading-I material and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and MORD Technical Specification Clause 406. and direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incidentals. The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and applying primer coat on prepared surface granular base including cleaning of the road surface with Hydaulic brooms and spraying primer @ 0.850 Kg. (zero point eight five zero kilogram) per square metre SS-I emulsion with nano technology using mechanical means as per MORD technical specifications clause 502 as per the entire statisfaction and direction of Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and applying Tack Coat with bitumen emulsion (RS-I) with Nano technology using emulsion distributor at the rate of 0.250Kg. (Zero point two seven five Kilogram) per Square metre on granular / bituminous surface as per MORD technical specifications clause 503 or as directed by the Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as per Table 500.4 premixed with bituminous binder VG-10 at the rate of 3.3% (three point three percent) of mix with Nano Technology , transported to site upto a laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per MORD Technical Specification Clause 504 or as directed by the engineer-in-charge including carriage of materials within all leads and lifts and other incidentals.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying Semidense bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 (seventy five) tonnes per hour with nano technology using crushed aggregates of specified grading, premixed with bituminous [email protected] to 5 (four point five to five ) per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignmernt , rolling with smooth wheel , vibratory and tandem rollers to achieve the desired compaction as per MORD specification clause No 509 complete in all respect and to the entire satisfaction of Engineer - in- Charge including hauling /carriage of materials to various location through all modes of transportation in all leads, lifts and other incidental complete in all respect.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated plain cement concrete nominal mix 1 : 2 ½ : 5 ( one cement isto two & half sand isto five graded crushed /broken stone aggregate 40mm ( forty millimetre) nominal size) in substructure as per drawings and M.O.R.D. technical specifications section 800, 900 and 1200 including the cost of form work curing complete and including hauling of materials in all leads, lifts and other incidental or as per the entire specification and directions of Engineer-in-Charge . The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying cold plastic road marking paint of approved manufacture 2.5 mm (two decimal five millimetre) thick with reflectorising glass beeds at the rate 250 (two hundred fifty gram) gram per square metre area, thickness of 2.5 mm (two point five millimetre) is exclusive of surface applied glass beeds as per specification and with strips of 0.10 ( zero decimal one) metre width in centre lines or edge lines of the road or as per directions of Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and erecting 900mm (nine hundred millimetres) equilateral triangle board cautionary/mandatory/informatory sign boards of retro reflectorised sign as per IRC: 67 made of encapsulated lens type reflective sheeting, fixed over aluminium sheeting 1.5 mm (One point five)millimetre thick (The aluminum sheeting shall be provided with duly painted 25x25x3mm (twenty five in to twenty five in to three millimeters) angle iron frame along its periphery), supported on a mild steel angle iron posts 75x75x6mm (seventy five into seventy five into six millimeters) fixed to the ground by means of of properly designed foundation in concrete block of grade M-15 (M-fifteen) nominal mix, of size 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimeters) whereas the cement concrete block will be 600mm (six hundred millimeters) below the ground level, complete as per MORD technical specification section 1700 and as per the directions of the Engineer-in-charge inclusive carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and erecting 600mm (six hundred millimetres) Circular board cautionary/mandatory/informatory sign boards of retro reflectorised sign as per IRC: 67 made of encapsulated lens type reflective sheeting, fixed over aluminium sheeting 1.5 mm (One point five)millimetre thick (The aluminum sheeting shall be provided with duly painted 25x25x3mm (twenty five in to twenty five in to three millimeters) angle iron frame along its periphery), supported on a mild steel angle iron posts 75x75x6mm (seventy five into seventy five into six millimeters) fixed to the ground by means of of properly designed foundation in concrete block of grade M-15 (M-fifteen) nominal mix, of size 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimeters) whereas the cement concrete block will be 600mm (six hundred millimeters) below the ground level, complete as per MORD technical specification setion 1700 and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and erecting 600 x 450 mm (six hundred into four hundred fifty millimetres) rectangular board cautionary/mandatory/informatory sign boards of retro reflectorised sign as per IRC: 67 made of encapsulated lens type reflective sheeting, fixed over aluminium sheeting 1.5 mm (One point five)millimetre thick (The aluminum sheeting shall be provided with duly painted 25x25x3mm (twenty five in to twenty five in to three millimeters) angle iron frame along its periphery), supported on a mild steel angle iron posts 75x75x6mm (seventy five into seventy five into six millimeters) fixed to the ground by means of of properly designed foundation in concrete block of grade M-15 (M-fifteen) nominal mix, of size 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimeters) whereas the cement concrete block will be 600mm (six hundred millimeters) below the ground level, complete as per MORD technical specification section 1700 and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and erecting 900mm (nine hundred millimetres) octagon board cautionary/mandatory/informatory sign boards of retro reflectorised sign as per IRC: 67 made of encapsulated lens type reflective sheeting, fixed over aluminium sheeting 1.5 mm (One point five)millimetre thick (The aluminum sheeting shall be provided with duly painted 25x25x3mm (twenty five in to twenty five in to three millimeters) angle iron frame along its periphery), supported on a mild steel angle iron posts 75x75x6mm (seventy five into seventy five into six millimeters) fixed to the ground by means of of properly designed foundation in concrete block of grade M-15 (M-fifteen) nominal mix, of size 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimeters) whereas the cement concrete block will be 600mm (six hundred millimeters) below the ground level, complete as per MORD technical specification section 1700 and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD instructions, specifications section 1700 and annexure 1700.1 and drawing. Three MS Plates of 1.6 mm (one point six millimetre) thick, top and middle plate duly welded with MS flat iron 25 mm x 5 mm (twenty five millimetre into five millimetre) size on back on edges. The lower plate will be welded with MS angle iron frame of 25 mm x 25 mm x 5 mm (twenty five millimetre into twenty five millimetre into five miliimetre). The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 Nos. (Two Nos.) 75 mm x 75 mm (seventy five millimetre into seventy five millimetre) of 12 SWG (Twelve standard wire gauge) sheet tubes posts duly embedded in cement concrete M-15 (M-fifteen) nominal mix 1 : 2½ : 5 (one cement : two & half sand : five graded crushed/broken stone aggregate) 40 mm (forty millimetre) nominal size and curing complete of concrete blocks of 450 mm x 450 mm x 600 mm (four hundred fifty millimetres into four hundred fifty millimetres into six hundred millimetres), 600 mm (six hundred millimetres) below ground level or and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and erecting Direction and Place Identification signs board upto 0.90 sqm (zero point nine) square metre of retro reflectorised sign as per IRC: 67 made of encapsulated lens type reflective sheeting, fixed over aluminium sheeting 1.5 mm (One point five)millimetre thick (The aluminum sheeting shall be provided with duly painted 25x25x3mm (twenty five in to twenty five in to three millimeters) angle iron frame along its periphery), supported on a mild steel angle iron posts 75x75x6mm (seventy five into seventy five into six millimeters) fixed to the ground by means of of properly designed foundation in concrete block of grade M-15 (M-fifteen) nominal mix, of size 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimeters) whereas the cement concrete block will be 600mm (six hundred millimeters) below the ground level, complete as per MORD technical specification section 1700 or and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Reinforced cement concrete mechanically mixed and vibrated M-15 grade nominal mix 1:2½:5 (one cement: two & half sand: five graded crushed/broken stone aggregate 40mm (forty miilimetre) nomianl size) kilometre stone of standard design as per IRC:8 (eight) fixing in position including painting and printing etcetera as per drawing and MORD technical specifications for rural roads clause 1703-- 5th( fifth) kilometre stone precast or and as per the directions of the Engineer-in-charge carriage of materials within all leads and lifts and other incidental. The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Reinforced cement concrete mechanically mixed and vibrated M-15 grade nominal mix 1:2½:5 (one cement: two & half sand: five graded crushed/broken stone aggregate 40mm (forty miilimetre) nomianl size) in ordinary kilometre stone of standard design as per IRC:8 (eight) fixing in position including painting and printing etcetera as per drawing and MORD technical specifications rural roads clause 1703 or and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and erecting 200 metre(two hundred metre) stones made of reinforcement cement concrete M-15 ( M-fifteen) grade nominal mix 1:2½:5 (one cement: two & half sand into five graded crushed stone aggregate 20mm(twenty millimetre) nominal size as per approved drawings; sign and size arrangement of letters including painting and lettering as per IRC-8 & IRC-26 and fixing at site complete and MORD technical specification clause 1703 or and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated concrete for plain cement concrete 1:2½:5 (one cement: two & half sand: five graded crushed/broken stone aggregate 40mm (forty miilimetre) nomianl size) laid for cradle bedding and curing complete including the cost of form work as per drawing and MORD technical specification section 800, 900, and 1100 or and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying ( to level or slope) 900 mm dia ( Nine hundred millimetre) diameter reinforced cement concrete heavy duty non pressure pipes IS class NP-3 for culverts in single row including fixing collar with cement mortar 1:2 (one cement: two sand) but excluding the cost of excavation,protection works,back filling, bedding concrete or 1st class bedding and masonry work in head walls and parapets as per drawing and MORD technical specifications section 1101 or and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Back filling behind abutments, return walls, wing walls and retaining walls etc. Complete as per drawings and MORD technical specification clause 1203 and 1604 as per section 300 or as directed by the Engineer-in-Charge ,including carriage of materials within all leads, lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete design mix having cement contents not less than 350kg (three hundred fifty kilogram) per cubic metre to obtain the minimum compressive strength of grade M-20 (Twenty) in sub structure as per drawing and MORD technical specification clause/section 800, 900 and 1200 including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in bed block,kerbs ,steps and wheel guard up to any floor level including the cost of form work ,curing complete, and hauling of material in all kinds of leads,lifts as per the entire satisfaction and directions of Engineer-in-charge.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete design mix having cement contents not less than 400kg (four hundred kilograme) per cubic metre to obtain the minimum compressive strength of grade M-25 (twenty five) in superstructure as per drawings and MORD technical specification of Rural Roads section 900 and 1400 including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in deck slab and curing complete including hauling of materials in all kinds of leads,lifts and other incidental as per the entire satisfaction and directions of Engineer-in-charge.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Supplying fitting and placing HYSD bar reinforcement (Fe-415) in substructure complete as per drawing and MORD technical specifications clause/Section 1000 and 1200 including cutting ,bending ,binding and placing in position complete in all respect including cost of binding wire upto any floor level as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Supplying fitting and placing HYSD bar reinforcement (Fe-415) in superstructure complete as per drawing and MORD technical specifications section 1000 and 1400 including cutting ,bending ,binding and placing in position complete in all respect including cost of binding wire upto any floor level as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Construction of un - reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 (forty three) grade cement or any other type as per Clause 1501.2.2 M 30 (thirty) (grade) coarse and fine aggregates conforming to IS: 383 (three hundred eighty three) maximum size of coarse aggregate not exceeding 25 mm, (twenty five millimetre) mixed in a concrete mixer of not less than 0.2 cum (zero point two cubic metre) capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side form work (steel channel, laying and fixing of 125 (one hundred twenty five) micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14 (fourteen) days using curing compound (where specified) and water finishing lines and grade as per drawing and MORD Technical specification clause 1501 and as per directions of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Planting rooted slips of large stature grasses on slopes, including supplying clumps of appropriate grasses, splitting into slips, trimming roots, preparing lines, digging planting hole to a max of 5 cm (Five centimetre ) depth with metal rod or wooden peg depending on nature of soil, planting slips at the rate of three per drill at the spacing specified, and subsequent watering (if necessary) On fill slopes of 15 to 34° and cut slopes upto 45°; drills at 10 cm spacing within the row and rows spaced at 0.5 m intervals and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Routine maintenance works for five years

For 1st Year

For 2nd Year

For 3rd Year

For 4th Year

For 5th Year