Renovation and Up gradation work of Gandhi Mandap, Guwahati

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

PCC Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

RCC Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

CEMENT PLASTER (IN COARSE SAND) 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab all colour and texture except black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 1000x1000 mm

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) Red sand stone/Brick Cladding: exposed face fine dressed with rough backing. 30 mm thick

Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required.

Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases.

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Stone work (machine cut edges Veneer work) for wall lining upto 10 m height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust), including rubbing and polishing complete. (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately). Kota stone slabs exposed face dressed and rubbed. 25 mm thick

Providing and fixing internal wall panels on Light gauge steel frame work with 12.5mm thick gypsum plaster board conforming IS 2095:2011 fixed on cement board as per standard sizes fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make, Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately Cement Fiber Board 8 mm thick as per IS 14862:2000 of type B (High pressure Steam Cured)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Salwood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood. 35 mm thick shutters

Providing and fixing factory made uPVC colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable. required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).

Providing and fixing factory made uPVC colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 125x64x2.50 mm

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing chromium plated brass handles with necessary screws etc. complete: 125mm

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. 75 mm

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 13.43.1 Water thinnable cement primer

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a primingcoat of approved steel primer all complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or any other accreditation body which operates in accordance with ISO/ IEC 17011 and accredits labs as per ISO/IEC 17025 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/ m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed andconsolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

For UGR Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area beyond 3 sq. metres

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in: R.S. Joists

Channels, angles, tees and flats

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge.(Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes,shelves,racks,almirah,cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-incharge.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. Kiln seasoned and chemically treated hollock wood

Float glass panes 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun +Reflectivity Index (SRI) of 105 on top of concrete roof in three coats [email protected] litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete all respect as per the direction of Engineer-in-Charge.

Grading roof for water proofing treatment with Cement mortar 1:3 (1 cement : 3 coarse sand)

Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge 50mm average thickness

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc

Supplying, Installing & testing 15mm CP health faucet of approved make with necessary CP flexible hose 1000mm long nozzle,CP wall flange, CP angle cock etc., complete Hindware: Cat F160068 Make: Hindware/ Cera/ Jaquar

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. With granite stone of area less than 0.50 sqm.

Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. (For Concealed Piping Hot and Cold Water) b) 20 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Downtake Shafts + Internal Exposed Pipings) b) 20 mm dia

c) 25 mm dia

d) 32 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge 80 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (For Terrace Ring Main) 32 mm dia

40 mm dia

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : a) 20 mm dia

b) 25 mm dia

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm dia

Providing and fixing gun metal non- return valve of approved quality (screwed end) : a) 80 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : a) 80 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589 /IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 200 mm dia

100 mm dia

80 mm dia

50 mm dia

40 mm dia

25 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 100 mm

Supplying, Installing, testing and commissioning of butterfly valves (PN 1.6) rating with bronze / gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes: 100 mm

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 200 mm

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required 200 mm

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589 /IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia

50 mm dia

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 3-way - 150 mm dia MS pipe

4-way - 150 mm dia MS pipe

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal valve

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.: 40 m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required: Gun metal

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required

25mm Air release valve as per IS:14845 ISI Marked

Providing and fixing wooden ceiling with 12mm and 6 mm thick marine plywood with one side decorative lamination on site pressed BWP grade marine ply as per IS 710 of approved brand with hot glue,painting edge,screw etc. complete as per direction of Engineer-in charge.(Payment of providing and fixing wooden frame ,ms work shall be paid separately)

Providing and fixing wooden column paneling/partion with 12mm with one side decorative lamination on site pressed BWP grade marine ply as per IS 710 of approved brand with hot glue,painting edge,screw etc. complete as per direction of Engineer-in-charge.(Payment of providing and fixing wooden frame ,ms work shall be paid separately)

Anti-Corrosive treatment on reinforcement Poviding and applying two coats of two component epoxy zinc rich primer like Fosroc Nitozinc Primer or equivalent on the properly cleaned reinforcement after the required chipping and cleaning of the concreate surface as per the manufacture’s specification at a dry flim thickness of 40 micron /coat.The epoxy zinc rich primer should have a adhesive bond strength with steel greater than 1.5 N/Sqm

Repair of spalled concrete Providing and Applying a two component structural grade polymer modified reinstatement mortar Fosroc Renderoc S2 or equivalent up to a thickness of 20 mm over a epoxy rasin bonding agent Nitobond EP. The cured mortar shall achieve a compressive strength of 12 N/mm² in 1 day & 45 N/mm² in 28 days with Flexural strength 8 N/mm² in 28 days. Chloride diffusion coefficient shall be Nil after 24 hours when tested by Accelerated Electrochemical chloride ion diffusion test method and the depth of carbonation shall be Nil after 24 hours when tested by Accelerated carbonation test. In addition to this percentage of water absorption should be 0.45 after 24 Hrs in immersion test.

Epoxy Grout Providing and Sealing the cracks, in the concrete surface, after opening the cracks using suitable tools or saw cut in the crack, and cleaning the interior sides of the crack using sharp tools to remove all loose materials, using two component, high strength, non-sag, epoxy compound Nitobond PC 40 of fosroc make, inclusive of all Manpower, Material and Equipment. Injection Of Low Viscous Resin: BY Providing and grouting the cracks after fixing the injection ports at predetermine locations with the help of suitable injection grouting pumps at suitable pressures using two-component, high strength, low viscous epoxy injection resin system such as Conbextra EP 10 of Fosroc inclusive of Manpower, Material and Equipment". (Mode of measurement: Per litre of grout consumption.

Providing, Supplying, transporting materials, drilling holes by rotary hammer drill, dust removing, batching, mixing of resin and hardener, inserting & anchoring rebars of specified dia in existing concrete surfaces using polyester resin based anchoring grout like Fosroc Lokfix E75 or equivalent and necessary re baring of reinforcement steel up to 200mm depth( Cost of the reinforcement will be charged extra) 12 mm Dia

Application of Epoxy Bonding Agent Share Anchoring Providing and applying structural grade long pot life epoxy bond coat of Nitobond EP prior to building up of section with any type of mortar/ concrete to ensure bond between old concrete & new concrete by brush application as per the manufacturer’s specifications. (Mode of measurement- per sqm of application of concrete surface )

Micro Concreting Providing and laying micro concrete up to the required thickness as per the drawing by consultant on the designated area to the prepared slurry tight shuttering with proper shear connector and bonding agent where ever necessary, The fluid micro-concrete repair material shall be a single component, cement based, Renderoc RG or equivalent micro-concrete to which only the site-addition of clean water (and approved graded coarse aggregates where specified) shall be permitted. The micro concrete shall contain no metallic aggregates, or chlorides and shall be shrinkage compensated in the plastic state. The micro concrete in the flow able consistency should achieve a compressive strength of 50 N/mm2 after 28 days at 30C as per BS 4551-80. The unrestrained expansion shall be between 1 - 4% as per ASTM C827-1987. Again as per BS 4551-80 the flexural strength shall not be less than 5 N/mm2 @ 28 days. The micro concrete shall have a coefficient of thermal expansion 10-12 X 10¯6/°C & Thermal conductivity 1.5 W/m°C The mixed density of micro concrete shall exceed 2100-2200 kg/m3 at 27ºC

Carbon Fibre Wrapping: Application of carbon fibre wrapping on beam and column :- Strengthening structural elements with high performance, high strength carbon fibre system like Fosroc Nitowrap CW of required GSM or equivalent Carbon composite fibre wrapping system comprise of fibre sheet and compatible saturant, by dry/wet layup system including, Surface preparation: Grinding/ moulding concrete substrate, cleaning it with wire brush removing oil, laitance if present, rounding sharp edges to min 25 mm radius etc. complete. Profiling: Applying compatible primer on prepared substrate, Filling the holes and uneven surface with thixotropic putty etc. complete Wrapping: Wrapping the fibre sheet to structural element at desired orientation using tamping roller to avoid any air voids etc. repeat the same procedure for multiple layer with the interval of 8 hrs. The fibre should have nominal thickness 0.30mm, tensile strength 3500 N/mm² and tensile modulus 285 X 10³ N/mm². Applying second coat of saturant after min. 12 hrs, rectify air voids if any paste the river sand on it to make surface rough to take any further finishes. Cost inclusive of both design and application as per the satisfaction of the engineer in charge.

OUTDOOR CEILING Providing & Fixing 6mm th. merino (EWC Boards) Compact exterior grade decorative HPL Laminateas per EN438-6 Type EGS manufactured using acrylic resins under high pressure and temperature and hardened with Electron Beam Curing thus providing weather resistance and light fastness GRADE : EWC THICKNESS : 6MM COLOUR : ANY

SIGNAGE Steel Letter (Outdoor Quality) Specification: 304 Stainless Steel Letter with 20 Gauges. Thickness of the letter : 2.50 Inch Depth/ Raise Size Of Letter: 1.5 Inch (20'' Height X12Nos=240 Inch)

Steel Board & Engraving Specification: 304 Stainless Steel with 20 Gauges, Black engraving, 30"X48"=1440SqInch

Conducting rebound hammer test as per IS-13311(part-2)1992 (Each test consist of 5-6 nos R H reading)

Conducting Ultra Pulse Velocity Test as per IS-13311(Part-2)1992 (Each test consist of UPV reading)

Supply with labour rate for fixing C.P. brass twin peg robe hook of approved quality fixed with C.P. brass screws.

Supplying, fixing and testing unplasticized PVC soil and waste pipes (SWR Type - B) with solvent cement joints & fittings conforming to IS 13592 , with all necessary specials like bends,tees, offsets, doorbends, junctions,cowls etc., laid under floor/fixed on walls etd., complete with pressure testing and commissioning of system .The fittings should be of pasted type(solvent cement). The quoted rate shall be inclusive of cost of suitable supports,clamps etc a) 32 mm dia

e) 75 mm dia

f) 110 mm dia

Supply, installation and testing 100mm inlet and 75 mm outlet - SS Grating with PVC floor Trap with a minimum water seal of 50mm complete with with inbuilt cockroach trap :: i) setting the drain in cement concrete 1:2:4 ii) inlet with a perforated 1.25mm thick S.S 304 grating iii) P or S trap arm of desired length

Clean Out Plug:- Supply and installation of PVC clean out plugs with suitable inset keys for pvc pipes with a threaded socket as necessary (Dia 110)

Supplying, fixing and testing PVC Rain water collection kurra with leaf trap grating made out of UPVC with flange and grating for rainwater outlets on terrace, complete. a) 75 mm dia

Supply, installation testing & commissioning Forged Brass Air Release valve-Screw Type complete with special supports. 25 mm dia

Supplying, installing, testing and commissioning of brass forged body ball valves screwed with teflon seals, stainless steel ball & stem, with all suitable nuts, bolts, etc complete. 40 mm dia

Supplying, installing, testing and commissioning of rubber expansion bellows with accessories like nuts, bolts, etc complete. 200 mm

Supplying, installing, testing and commissioning of brass forged body ball valve screwed with SS ball and spindle and teflon seats. 50 mm dia

Supply, fixing and commissioning of first aid box complete with fixing brackets and all necessary accessories, tools etc.

Steel buckets with Pole Mounted stand filled with sand

Supplying, installing and commissioning Portable Fire extinguishers of following type & capacity. Carbon-di-oxide Gas Type Fire Extinguisher 4.5 Kgs, squeeze Grip, Discharge Time less than 10 Secs, Controllable discharge mechanism with nozzle, bend, Hose and wall mounting bracket etc., Applicable on Class B&C Fire, B Rating 21B, Can Construction : Hot Spinning / Forging, Valve Construction : Forging & Machining, Internal Coating of Can : Seamless Cylinder, External Coating of Can : Spray Painting, Sheet metal thickness : 4.5MM, ISI Approved as per IS:2878:2004

Supplying, installing and commissioning Portable Fire extinguishers of following type & capacity. ABC Powder 6 Kg Fire Extinguisher containing Mono Ammonium Phosphate Powder 50, Stored Pressure Type, Pressure Gauge, fitted with discharge hose, wall mounting bracket etc., Discharge Time less than 15 Secs, Controllable discharge mechanism, Range minimum 4 Meters, applicable on Class A,B,C and electrically started Fire, A Rating- 8A, B Rating 34B, Can Construction : Deep drawn & Co2 Mig welded, Valve Construction : Forging & Machining, Internal Coating of Can : Epoxy Powder coating, External Coating of Can : Epoxy Polyester Powder coating, Sheet metal thickness : 1.60MM, ISI approved as per IS:15683:2006

Supplying and installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC reflective self adhesive vinyl painted foam board, complete with mirror fasteners. Signage with printed "IN CASE OF FIRE, USE STAIRS UNLESS INSTRUCTED OTHERWISE" of 1.5cm height letters in red with white back ground. The size of the board shall be 25cm x 30 cm and shall be fixed at the height of 2 mts. from finished floor near Manual call points.

Floor identification signage ( i.e., GROUND FLOOR …etc.) at each stair enclosure on every floor, indicating the floor number in words, lettering size shall be 7.5 cm with contrasting color from back ground. Size shall be 15cm x 60cm.

Fire Exit signage- Double sided: 150 x 400 Providing and fixing "Fire Exit" letters signage (with or without directional arrows as per signage plan, ref. by architect). Signage to be made of 3 mm thick foam board with edge to edhe self-adhesive, self luminiscent Forex or equivalent inyl stuck on it. Fix green vinyly to cover Forex vinyl leaving 6 mm border around edges with Exit letters cut-out. The exit letters shall be 150 mm height. Double side false ceiling suspended with chain look and hook. Unidirectional, printed both sides with sinle arrow or double arrow.

Supplying and installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC reflective self adhesive vinyle painted foam board, complete with mirror fasteners. Fire hose reel

Lifts

Fire extinguishers

Staircase Arrow Sign - Imported Acrylic Sheet 4mm, grade 1 autoluminscent film, preplotted media with extra over laminate at the back. Size: 6’’ x 4’’

EARTHING, LIGHTNING ARRESTOR & EARTHING STRIPS Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and fixing of lightning conductor finial, made of 25mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.ed.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2x2.5 sq.mm + 1 x 2.5 sq.mm earth wire (For 6A Power Point looping & Switchboard to Switchboard looping)

2 x 4 sq.mm + 1 x 4 sq.mm earth wire ((For 6/16A Power Point looping)

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing of following sizes of medium class PVC conduit along with acessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single Pole (5-32A)

Double pole (32A)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.. 40A

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required. 8 way , Double door

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. 8 way (4 + 24), Double door

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

CCTV SYSTEM Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

PUBLIC ADDRESS SYSTEM Supplying, installation, testing & commissioning of 240W Mixer Amplifier with USB/Bluetooth MAKE: BOSCH (BOSPLE1ME2403IN)

Supplying, installation, testing & commissioning of 6W ceilingspeakers complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

LIFT Passenger lift 6 Persons including all

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 88 m head

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads. 450 lpm at 35 m head (To be provided at Terrace as per recommendations of Fire Safety Officer and rules of local Fire Department / Fire Prevention Wing)

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

SUBMERSIBLE WASTE WATER TRANSFER PUMP Procurement, supply, erection & commissioning of electrically operated submersible wastewater transfer pump (IE3 Rating & Suitable for aluminium cabling) complete with mechanical seals,protection sensors overload/undervoltage tripping/ {oil leakage if required)/ electronic (magnetic) level sensing unit & dry run cut off. The pumps should be with bronze or S.S. impeller,to be housed inside sumps as indicated in drawing.Minimum Partcle size upto 50 mm . All accessories for fixing along with delivery hose should be included in the offer. Electrical auto control panel with level sensor, logic controller, push putton emergency stop etc should be included in the offer. PUMP ROOM SUMP PUMP ( 15 CUM/HR. 20M HEAD, 1 KW)

UPS Supply, Installation, testing and commissioning of 1 phase Input and 1 phase output, 50Hz, IGBT rectifier based On-Line UPS along with dry cell battery, Connecting Cables, battery rack and all accessories as required. Technical Specification shall be satisfy as mentioned below: Input & Output Voltage: 220V ± 5%, with Phase Reversal Frequency: 50Hz Harmonics : < 5%. Out Put P.F : > 90%. Rectifier: IGBT based IGBT Rectifier with Builtin Isolation transformer (External Transformer is not aacceptable) Filter-Electromagnetic interference (EMI),radio-frequency interference (RFI) Communication Port: RS485, RJ45 Back-Up Time: 30 Munities at 100% load. Ambient Temperature: 0°C - 35°C Protection Class: IP 20 Noise Level: < 60 Db 5 kVA

5kW DOL Starter Local Control Panel for Boosting Pump 9-13A MPCB, 25A 3P Power Contactor, Start/Stop Push Button, On, Off, Trip Indicating Lamp

EARTHING STRIPS Supplying and laying 50 mm X 6 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 40 mm X 6 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 50 mm X 6 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying and laying 40 mm X 6 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supply & installtaion of 20W 4ft LED Batten (wall mounted) will give nominal system lumen output of 2000lm and a minimum system efficacy of 100lm/W. The luminare should have beam angle of 120 Deg with a color temperature of 4000K ,CRI 80, THD <15% and PF ≥0.95. The luminaire shall meet IP20 having Aluminium housing and high efficient PC diffuser for better light distribution. The luminaire has the features of Input Voltage : AC220-240V, 50/60Hz, Voltage operating range : 90-305V with High Surge Protection : 2.5 KV, Operating temperature : -10Deg to 45Deg

Supply & installtaion of 10W 2ft LED Batten (wall mounted) will give nominal system lumen output of 1000lm and a minimum system efficacy of 100lm/W. The luminare should have beam angle of 120 Deg with a color temperature of 4000K ,CRI 80, THD <15% and PF ≥0.95. The luminaire shall meet IP20 having Aluminium housing and high efficient PC diffuser for better light distribution. The luminaire has the features of Input Voltage : AC220-240V, 50/60Hz, Voltage operating range : 90-305V with High Surge Protection : 2.5 KV, Operating temperature : -10Deg to 45Deg

Supply & installation of Recessed Mounted 12W LED COB Downlighter will give nominal system lumen output of 1200 lm and a minimum system lumen efficacy 100 lm/W. The luminaire should have a colour temperature of 4000K and CRI >80. The luminaire shall meet IP20 and with THD <10% and PF >0.9. The lumianire made of diecast alumianium material with high efficient polycarbonate diffuser for better light distribution. The lumianire has the features of input voltage : AC220-240V, 50Hz.

Supply & installation of Recessed Mounted 15W LED COB Downlighter will give nominal system lumen output of 1500 lm and a minimum system lumen efficacy 100 lm/W. The luminaire should have a colour temperature of 4000K and CRI >80. The luminaire shall meet IP20 and with THD <10% and PF >0.9. The lumianire made of diecast alumianium material with high efficient polycarbonate diffuser for better light distribution. The lumianire has the features of input voltage : AC220-240V, 50Hz.

Supply & installation of Recessed Mounted 30W LED COB Downlighter will give nominal system lumen output of 3000 lm and a minimum system lumen efficacy 100 lm/W. The luminaire should have a colour temperature of 4000K and CRI >80. The luminaire shall meet IP20 and with THD <10% and PF >0.9. The lumianire made of diecast alumianium material with high efficient polycarbonate diffuser for better light distribution. The lumianire has the features of input voltage : AC220-240V, 50Hz.

Supply & installation of Surface Mounted 18W LED Downlighter will give nominal system lumen output of 1800 lm and a minimum system lumen efficacy > 100 lm/W. The luminaire should have colour temperature of 4000K and CRI≥80. The luminaire shall meet IP20 and with THD <10% and PF >0.9. The luminaire housing made of diecast aluminium housing with PC diffuser for better light distribution. The lumianire has the features of input voltage : AC220-240V, 50Hz.

Supply & installtaion of 5W/Mtr LED strip light will give nominal system lumen output of 500lm/Mtr and a minimum system efficacy of 100lm/W. The luminare should have color temperature of 6500K ,CRI≥80, THD <15% and PF ≥0.90. The luminaire shall meet IP20. The luminaire has seperate energy electronic driver & the luminaire has the features of Input Voltage : AC220-240V, 50Hz.

Supply & installtaion of 10W Track Light with 2Mtr. Track & I-connector will give nominal system lumen output of 750lm and a minimum system efficacy of 75lm/W. The luminare should have color temperature of 4000K ,CRI≥80, THD <20% and PF ≥0.90. The luminaire shall meet IP20. The luminaire has seperate energy electronic driver & the luminaire has the features of Input Voltage : AC220-240V, 50Hz.

Supply & installtaion of 5W LED Uplight with minimum system efficacy of 70lm/W. The luminare should have color temperature of 3000K ,CRI≥70, THD <30% and PF ≥0.90. The luminaire shall meet IP65. The luminaire has the features of Input Voltage : AC220-240V, 50Hz.

Supply & installtaion of 8W LED Uplight with minimum system efficacy of 70lm/W. The luminare should have color temperature of 3000K ,CRI≥70, THD <30% and PF ≥0.90. The luminaire shall meet IP65. The luminaire has the features of Input Voltage : AC220-240V, 50Hz.

Supply & installtaion of 12W LED Uplight with minimum system efficacy of 80lm/W. The luminare should have color temperature of 3000K ,CRI≥70, THD <30% and PF ≥0.90. The luminaire shall meet IP65. The luminaire has the features of Input Voltage : AC220-240V, 50Hz.

Supply of Surface Mounted 10W LED Bulkhead will give nominal system lumen output of 900 lm and a minimum system lumen efficacy 90 lm/W. The luminaire should have a colour temperature of 6500K and CRI >80. The luminaire shall meet IP65 and with THD <10% and PF >0.9. The lumianire made of diecast alumianium material with high efficient polycarbonate diffuser for better light distribution. The lumianire has the features of input voltage : AC220-240V, 50Hz.

Installation, testing and commissioning of MCCB with enclosure complete with all accessories to accommodate on/in surface or recessed including drilling holes, connections etc as required . 40A, DP MCB with Enclosure

12 way (4 + 36), Double door

Supplying of 40A, DP, 10kA, C-Curve MCB as required

Supplying of 32A, 4P, 10kA, C-Curve MCB as required

Supplying of 63A, 4P, 10kA, C-Curve MCB as required

12 way (4 + 36), Double door

HVAC WORK Air Handling Units for General Area Supply Installtion, Testing and commissioning of factory built ceiling suspended/floor mounted double skin type Air Handling Unit with sectionalized, made of extruded Al section frame structure with thermal break profile of 25±2mm thick panels consisting of GI casing of thickness 0.6mm outside layer and 0.6mm plain GI sheet inside layer with polyurethane foam (PUF) insulation of density 40±2Kg/cum factory injected between them by injection moulding machine complete with forward/backward curved blower section, 4/6 row deep chilled water cooling coil section with aluminium finned copper tubes (Tube thickness not less Than 0.43 mm & 12-13 Fins /Inch). The AHU shall be completed with stainless steel drain pan with19 mm thck clsed cell class- O nitrile insulation,fire retardent canvas connection and necessary vibration isolation arrangement etc. The motor shall be TEFC drive motor (IE3 and VFD compatible) suitable for 415±10% volts, 50 Hz, 3 phase, A.C. supply. The complete AHU shall cinfirm to specification & face velocity across cooling coil shall be limited to 500 FPM maximum and fan oullet valocity not more than 1870 FPM. The static pressure will be calcualted by HVAC contrctor on basis of final duct layout. 3200 CFM, 35 mmwc SP, 8.0 TR, Ceilling suspended Filter :Pre filter 90% efficiency to 10microne

3500 CFM, 35 mmwc SP, 10.5 TR, Ceilling suspended

VRV/VRF Outdoor Units_Cooling Supply Installation, Testing and Commissioning of Modular Type Out Door Units equipped with modular type high efficiency all inverter technology based hermetically sealed scroll compressors suitable for R410A refrigerant, suitable for operation on 400±5% volts, special heat exchanger with al. fin and copper tube, Centrifugal fan for condenser, electrical and microprocessor base panel and all accessories for proper functioning the unit. The Outdoor and Indoor Unit shall be integrated with special super wiring system with centralised remote control system into one common wiring. ODU having auto check function for correction eroor, auto addressing system, oil return system, soft starters for compressor motors, under voltage/over voltage trip, single phase preventers, communication card etc. The ODU shall be suitable for working on 49⁰C ambient temperature and ODU dB level Less than 65 at distance 1 Meter. The Outdoor Unit complete with all interconnecting piping, joints and U bend with in the condensing unit .Unit shall be painted two coats of clear transparent polymer coating for protection against corrosion from ambient air pollution. The EER of ODU mentioned shall be minimum 11.2 at 100% load at 35⁰C ambient temperature(AHRI Condition) Unit price shall be inclusive of Refrigerant Gas for full system, MS structure and RCC/PCC Foundation required etc. to complete the system as required as follows:- 26HP

Refrigerant Pipe for VRF/VRV System Supply, installation, testing and commissioning of interconnecting high pressure copper refrigerant piping work suitable for refrigerant R410A/R32 duly insulated with class-O, GC cloth pasted elastomeric nitrile rubber type tubular insulation of density 40 ~60kg/m3 between indoor & out door units. External refrigerant piping shall be laid on 16G GI covered perforated cable trays, it shall include the cost of all the fitting, insulation and all required fittings, joints etc. as per drawings of the following sizes. Piping inside occupied area and vertical shaft shall de supported using GI Hangers. The 19mm thick insulation shall be considered for 19.1mm and above dia copper pipe and 13mm thick from 15.9mm dia and below size. All exposed pipe shall have weather proof quoting on GC Cloth and cost to be included in the piping rate and cable tray is quantified separately. Price of Cable Tray will be charged in item of cable tray in electrical part. External piping should be covred with the GI sheet on cable tray for weather protection. 41.3mm dia (1.4mm thick.)

34.9mm dia (1.2mm thick.)

28.6mm dia (1.0mm thick.)

19.1mm dia (0.80mm thick.)

15.9mm dia (0.80mm thick.)

12.7mm dia (0.80mm thick.)

Refnet Supply, installation, testing and commissioning of copper Refnet factory febricated along with suitable insulation as per shape of the refnet as required to connect the above VRV/VRF indoor and outdoor units.

Communication and Transmission Cable Supply,installation,testing and commissioning of 2C x 1.0 sqmm copper conducter flexible cable laying in PVCcunduit with bent, tee as require for communication beetween VRV/VRF IDU and ODU and also for Central remote controlling system.

Propeller Fan Supply, installtion,Testing and commissioning of Propeller fan wiith motor complete in all respect & of following capacities. The casing of propeller fans Shall be PVC / METALIC and should be lower noise level. The fan shall be suitable for 230V, 1Ph., 50Hz AC power supply, 75 CFM

Air Distribution System GI Duct Supply, Febrication & Fixing of 120 GSM GS sheet metal rectangular ducting as per IS 655/SMACNA complete with turning vanes, companion flanges, support, sealing of all seams with a suitable metal sealant as per drawings. 24 G

Duct Thermal Insulation Supply and Fixing of Duct thermal insulation with following thickness Class-O Nitrile sheet (density 40-60kg/cum)/ XLPE(33±3kg/cum) sheet insulation with factory pasted aluminium foil on one side on the duct using low VOC adhesive. 13mm thick with aluminium foil if duct passing through airconditioning area.

Underdeck Insulation Supply and Fixing of thermal insulation with following thickness Class-O Nitrile sheet (density 40-60kg/cum)/ XLPE(33±3kg/cum) sheet insulation with factory pasted aluminium foil on one side for underdeck insulation using low VOC adhesive and screwing with GI washer. 25 mm thick for Nitrile / Xlpe Insulation for underdeck insulation .

Duct Thermal and Acoustic insulation Supply and fixing of duct accounstic lining inside the ducts with 12mm thick Class-1 open cell nitrile sheet (density 140-160kg/cum) pasted inside the duct using low VOC ashesive and harnessed with GI NUT Bolt.

Auminium Powder Coated Grill Supply , Installtion, testing and balancing of Linear Discreet / ContiniousSlotted Diffuser extruded aluminium constuction with powder coated finish complete in all respect as per drawings.

Auminium Powder Coated Rain Protectio Louver Supply Installation, testing and commissioning of rain protection louver for fresh air or exhaust air complete with extruded aluminium constuction with powder coated finish complete in all respect as per drawings.

Aluminium Collar Damper Supply Installation, testing and commissioning of Coller Damper of of aluminium constuction with black paint finish and complete in all respect as per drawings.

GI Duct / FA Damper Supply Installation, testing and commissioning of Duct/FA Damper of 16G GI constuction and complete in all respect as per drawings.

Motorised Fire Damper Supply ,Fixing,testing and commssiooning of MOTORIZED fire dampers in supply air duct /main branch and reurn air path as and where required with control wiring. The damper shall be motorised and spring return actuator to close the damper in the event of power failure automatically and poen the same incsae of power being restored. The damper shall also be closed in the event of fire signal completeas required and as per specifications and atleast 90 minutes rating as per UL555/1995 TESTED BY CBRI.

Motorised actuator with Controller for above damper.- 10NM

Fire Retardent Canvas Connection Supply, Fixing,testing and commssiooning of 150 mm depth fire retardent canvas connection along with proper nut bolt joint.

Drain Piping Supply,installation,testing and commissioning of CPVC drain pipes density 20Kg/m3 complete with fittigs like elbows, tees, reducers, bends, flanges, supports with 9 mm thick class - O nitrile rubber insulatiions complete with supports as per drawings and specifications of below sizes. 40 mm dia

32 mm dia.

25 mm dia

Electrical Works PDB Panel for VRV Outdoor Units & ahu -Terrcae Supply, Installation, Testing, Comisioning of following cubicle type panels construcred from 2mm thick sheet steel enclosed separate compartment for each feeeder or feeders, front operated. rear connection indoor type(IP54), dust proof, lockable door, complete with all internal wiring, colour coading with ferruls, removal cable glands plate, bonding to earth and powder coated painting, all accessories and supporting structure. All ammeters with CT and ASS, voltmeter and energy meters and all panel components as specified. MS base frame, separate adequate cable alley for incomming and outgoing termination. All switch gear to have protection levels as specified. TPN bus bars shall be of Aluminium and shall be sleeved. Phase bus bars shall be rated at 20% higher and neutral bus bar shall be of 100% capacity. Minimum density of Aluminium bus bars for current carrying capacity shall be 1.0 amp per square mm. Incomer i) 1 No. 415V, 4P, MCCB, 200A, 50kA with inbiult microprocessor based release with E/F, S/C, O/L as Incomer. Provide pottential free contact to connect with fire interlocking system. ii) 1 set digital ammeter with CT, ASS. iii) 1set digital voltmeter, VSS. iv) Phase indicating lights in R-Y-B colour. BUS Bar TPN bus bars shall be of Aluminium and shall be sleeved. Phase bus bars shall be rated at 320 amps and neutral bus bar shall be of 100% capacity. Maximum density of Aluminium bus bars for current carrying capacity shall be 1.0 amp per square mm. OUTGOING FEEDER : i) 25A 4P MCB 10kA - 06 Nos (1 # spare) with ON/OFF indication lamp. ii) 40A 4P MCB 10kA - 03 Nos (1 # spare) with ON/OFF indication lamp. iii) 63A 4P MCB 10kA -02 Nos (1 # spare) with ON/OFF indication lamp. PDB Panel for VRV Outdoor Units as described above.

Power Cable POWER CABLE :Supply Installation Testing Comisioning of following sizes of XLPE insulated PVC sheathed Copper conductor armoured cable of 1.1 KV grade on existing cable tray / surface including saddle, clamps etc. complete as required. as per specifications given in the tender. 4C X 10 Sqmm Copper Conductor multistrand armoured cable

4C X 6 Sqmm Copper Conductor multistrand armoured cable

3C X 2.5 Sqmm Copper Conductor multistrand armoured cable

3C X 1.5 Sqmm Copper Conductor multistrand armoured shielded cable

Control Cable Supply of following sizes of Copper conductor flexible wire of 1.1 KV grade on pvc conduit including saddle, clamps etc. complete as required. 2 x 1.0 Sqmm copper Flexible Cable

Cable Termination with Brass/SS Double Compression Supplying and making end termination with brass/ss double compression glands and aluminium lugs for following size of PVC insulated and PVC sheathed/ XLPE copper conductor cable of 1.1 KV grade as required. Gland for 4C X 10 Sqmm

Gland for 4C X 6 Sqmm

Gland for 3C X 2.5 Sqmm

Cable Tray Supply Installation, Testing and Comisioning of 1.6 mm thick (upto 300mm) and 2.0mm thick(above 300mm) hot plated GI pre fabricated perforated /Lader cable trays in horizontal or vertical formation complete with duely painted MS structural supports and Necessary demarkation. 150 mm wide x 25mm Height

Earthing Supply Installation Testing comissioning of GI Earthing along with suitable clamp & acessories for HVAC Equipment . 25 x 3 mm GI Earthing strip .

8 swg GI wire for earthing .

Supply, Installation, Testing & Commissioning of internet socket RJ45 on recessed metal box and cover plate (inclusive) including all accessories as required like connection etc at site.

Supply, Installation, Testing & Commissioning of CAT6 patch cord factory crimp cable for connecting RJ 45 including all required like connection etc at site. 1 metre

2 metre

Supply, Installation, Testing & Commissioning of Data Switch 16 port 10/100/1000 mbps, etc as required for site

Supply, Installation, Testing & Commissioning of CAT6 UTP 24 port Patch Panel complete with all accessories complete.

Supply, installation, testing and commissioning of Closed Network rack with Front Glass Door and Perforated double door on the back, vertical power strips of surge protection sockets, with Front and Rear Equipment mounting angle, Side panels shall be secured with sliding latches operated from inside the rack, Cable Entry at the rear top and bottom. Top Cooling Fans min 2 Nos. Earthing kit, front door lock Bolts nuts and all accessories. For Server Room. 9U RACK

Supplying, installation, testing and commissioning of 32 channels CCTV NVR 2 SATAPORT Network Video Recorder with all accessories such as internet connection, 2x4tb Hard Disk etc. complete in all respect to use at site.

Supplying, installation, testing and commissioning of 2MP full HD 1080p dome IP CCTV camera with all accessories complete in all respect to use at site.

Supplying, installation, testing and commissioning of 2MP full HD 1080p bullet IP CCTV camera IP-66 with all accessories complete in all respect to use at site.

Supplying, installation, testing and commissioning of 24 port rack mountable POE switch complete with all accessories .

Supply, Installation, Testing & Commissioning of CAT6 UTP 24 port Patch Panel complete with all accessories complete.

Supply, Installation, Testing & Commissioning of CAT6 patch cord factory crimp cable for connecting RJ 45 including all required like connection etc at site. 1 metre

Supplying, installation, testing and commissioning of 32 inch LED TV with VGA and HDMI Ports complete with all accessories .

4 TB 7200 RPM Surveillance HDD (Hard Disk Drive) MAKE: WESTERN DIGITAL

Supplying and fixing of ultra HD 65" inches crystal 4 K UHD Smart TV Make-LG

Supplying, installing, testing and commissioning of Hand held Microphone including accessories as required

Supplying, installation, testing & commissioning of Addressable Control Module UL listed complete as required.

Supplying, installation, testing & commissioning of 24 Vlt Power Supply for Control Module complete as required.

Supplying, installing, testing and commissioning of Pressure gauges of 0-16 kg/sqcm for pump sets and pipe lines for the respective floors near to the flow switches with Ball valves, siphon, Fittings like unions / colors / reducers etc. Glycerin filled pressure gauges to use on pump discharge lines.

Analogue addressable Main fire alarm panel

Manual Call Points

Build worth Trade Engineers

M/S I.S. Trading Co.