ADDITION /ALTERATION AND SPECIAL REPAIRS TO BLDG NO P-91 AT NRS THANE UNDER GE (NW) MANKHURD

Amount

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed.

Chipping, removing carefully loose/damaged concrete including plastering (total thickness upto 60mm ) from surfaces of RCC members, in any location by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land complete all as specified and directed. Note : 1) Hard concrete shall not be removed by force. 2) Item No.1.00 will not be applicable for the locations/areas where item No.2.00 is applicable.

Demolition of Brickwork of stone/boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan n.exceeding 6m mean radius built in CM 1:4 all as specified.

Demolition of cement concrete ,(reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hour between the coats, complete all as specified and directed. [Note :- Mode of measurement: superficial area covered between the end to end reinforcement bars (i.e., concrete area excluding all side covers) will be measured.]

M&L for Anticorrosive Treatment to Reinforcement using IPNET-RB of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces complete all as specified and directed. Note :- Mode of measurement: superficial area covered between the end to end reinforcement bars (i.e., concrete area excluding all side covers) will be measured.

M&L for providing TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips in various structural RCC elements like columns, beams, Slabs etc. including cutting, bending, fixing of bars with welding/ tying as required at site with & including binding wires etc. and all relevant works like anchoring of the bars in the existing RCC Members, complete all as specified and directed.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit, upto 20mm thickness while the bonding agent is still tacking, including levelling, profiling etc, complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit while the bonding agent is still tacking, exceeding 20mm thickness and not exceeding 40mm thickness in two layers, each layer not exceeding 20mm, including levelling, profiling etc, complete all as specified and directed.

M&L for casting & repairing of excessively damaged distressed RCC members (exceeding 40mm in thickness) with prebatched, prepacked, single component ready to use microconcrete from Fosroc (Renderoc RG) or equivalent of Dr. Fixit as approved by GE, at any level/ height and at any lead or lift as directed including prefabricated water tight formwork, centering, scaffolding, also including mixing , laying, levelling, finishing, curing etc as per manufacturer's specifications and all other relevant works, complete all as specified and directed. (Note : Reinforcement only shall be measured and paid separately).

M&L for 10 mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing surfaces even and smooth complete all as specified and directed Make: Easy Plast from M/s wall plast or chemplast or readyplast from Ultratech” Note: (i) The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with ready mix plaster and nothing extra shall be payable on this account. (ii) This item shall be operated only for the locations where the thickness of existing adjoining plaster is to be matched

M&L for 5 mm thick polymer modified ready mix cement based plaster on surfaces of ceiling including finishing the surface even & smooth without using extra cement, complete all as specified and as directed. Make : Easy plast from M/s wall plast or chemplast or Readiplast from ultratech. Note: The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with the ready mix plaster and nothing extra shall be payable on this account.

M&L for 15 mm thick polymer modified ready mix cement based plaster on the wall surfaces mixed with liquid water proofing compound in the proportion as per manufacturer’s instructions and including finishing the surfaces of the top layer even and smooth, complete all as specified and directed, Make : Easy plast from M/s wall plast or chemplast or Readiplast from ultratech. Notes : (i) The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with the ready mix plaster and nothing extra shall be payable on this account. (ii) WPC shall be paid for separately.

Supply only liquid water proofing compound.

M&L for prepration of newly plaster surface of wall two coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour Incl 2mm plaster of paris putty complete, as per manufacturer's specification.

M&L for prepration of newly plaster surface of ceiling two coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour Incl 2 mm plaster of paris putty complete, as per manufacturer's specification.

M&L for prepration of old plaster surface of ceiling complete removal of existing treatment and two coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour Incl 2 mm plaster of paris putty complete, as per manufacturer's specification.

M&L for prepration of old plaster surface of wall complete removal of existing treatment and two coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour Incl 2 mm plaster of paris putty complete, as per manufacturer's specification.

M&L for prepration of newly plaster surface of wall applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete all as per manufacturer instruction and all as specified and directed.

M&L for prepration of old plaster surface of wall washing rubbing down and stopping of distempered and painted surfaces and painted surface applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as per manufacturer instruction and all as specified and directed.

M & L for preparation of old painted wood surfaces of any description, not otherwise described over 10cm width or girth applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description, not otherwise described over 10cm width or girth applying two coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of New steel surfaces of any description, not otherwise described over 10cm width or girth applying two coat of synthetic enamel paint over one coat of red oxide, zinc chrome primer complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubish off the premises.

M & L for Dark shade/Double charge/ultracharge vitrified ceramic tiles light shade 10mm thick (square/rectangular) polished area of each tiles exceeding 0.42 sqm but not exceeding 1.0 sqm, in floors etc. set and jointer in neat cement slurry and pointed in white or coloured cement to match the shade incl 15mm thick CM 1:6 screed bed for laying floor finishes complete all as specified and directed.

All as per items above but in skirting or in dado including 10 mm thick rendering CM 1:4 complete all as specified and directed

M&L for non skid coloured ceramic tiles7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick CM 1:6 screed bed for laying floor finishes all as specifed and directed.

M&L for Glazed ceramic colour tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to matchincluding 10 mm thick rendering CM 1:4 complete all as specified and directed

M&L for coloured 300x600x7 to 8mm thick digital ceramic tiles on vertical surfaces such as skirting,dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick cement mortar backing coat in CM 1:4 etc, complete all as specified and directed.

M&L 16-18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. over screed bed or bedding layer of morar 15 mm in cement mortar 1:4set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as in cills, jambs etc, including moulding/rounding to edges of the slab and also including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L prepolished Machine cut kota stone slab flooring 20-25mm thick over 15 mm thick cement screed base CM 1;4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Durastone Heavy Duty vitrified tiles (300x 300) x 10-12 mm thick in floor set and jointed with neat cement slurry and pointed in coloured cement to match over screed bed or bedding layer of morar 20 mm in cement mortar 1:6 complete all as specified.

M&L for providing 75mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement, complete all as specified and directed.

M&L for special treatment of sunken portion of WCs and Bath room as per following stages: Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc . Stage 2:- Providing 10mm thick plaster in CM 1:4 with chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd Stage 3:- Applying Dr Fixit Primseal primer or STP Ltd(and allow to dry for 8 hours) under touch dry condition Stage 4:- Applying two coats of water proofing decorative elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP(The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per manufacturer instruction. Stage 5:-Again rendering 10mm thick in CM 1:4 mixed with Dr Fixit Pidicrete URP or plaster seal of STP Ltd. Stage 6. All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP. Stage 7:- Making holes in wall and fixing 600mm long 20mm dia GI spout for draining the surplus water if any.

Taking up or down GI steel tubing and connection including fitting, cleaning for reusing if any as specified and as directed for the following sizes:- (a) 15mm bore.

(b) 20mm bore.

S & F of 16 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings (incl provn of special fittings i.e. brass elbow, brass tee, Male brass threaded adaptor, female brass threaded adaptor etc required for fixing of bib tap, stop valve with CPVC pipes) concealed in walls/ ceiling or laying in floors etc., also including cutting chases, grooves and making good the same in CM 1:3 after fixing of pipes / fittings, complete all as specified and directed.

all as per item no 40 above but 20mm outer dia.

S&F for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. .

S&F PVC connections 15mm size with PTMT nuts of length 600mm.

S&F towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (Min wt 190 gms).

S&F in repairs 10 litres PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified and as directed .

S&F in repairs 15 mm dia bib taps,fancy type chromium plated cast copper alloy with crutch , screwed down screwed for iron or for brass ferrule complete all as specfied and drecetd.

S&F in repairs 15 mm dia bib taps two way cock , cast copper alloy with crutch , screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated Make Jaquar or equivalent make as approved complete all as specfied and drecetd

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repairs 15 mm Bore dia Pillar taps fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe make : JAQUAR vignette prime series table mounted tall body complete all as specfied and drecetd.

S&F in repairs 15 mm bore stop cock cast copper alloy with crutch or for brass chromium plated with fancy shank and cup (concealed type) complete all as specfied and drecetd.

S & F in repair for Stop cock /angle CP fancy type 15 mm bore screwed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for Unions complete all as specified and directed.Make Cera,Parryware, ESSCO.

S&F vitreous china, table top wash hand basin oval shape size( 420x420mm x135 mm) cat No : ARS-WHT-0538 Make of JAQUAR fixed on granite counter top slab including brass chromium plated full threaded waste coupling with grating 32mm dia pvc waste pipe complete all as specified and directed. (Note: Granite slab, RCC plat form, brick wall support etc shall be measured and paid separately)

S&F in repairs, vitreous china wash down water closet pan (pedestal pattern), white, with flush pipe and pvc connection of 450mm long fixed complete all as specified. Make Cera,Parryware, ESSCO all as specified and directed.

S&F in repairs plastic water closet seat cover white or any colour closed padestrial pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and fixed complete all as specified Make Cera,Parryware, ESSCO.

S&F for towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges, complete all as specified. Make: Jaquar Cat Part No.ACN 1111SM or equivalent in Make as per Appx `E' to Particular specification.

Supply only stainless steel wire cloth 0.36mm mm nominal dial of wire and average width or aperature 1.40mm for fixing to wooden door/ window shutters in any position with new beads/ steel section as required for securing including dismantling of old jalli and painting to match with existing complete all as specified and as directed.

supply and fixing Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane 4 mm thick quality fixing to wooden door/aluminium window shutters in any position with new beads/ steel section as required for securing including dismantling of old jalli and painting to match with existing complete all as specified and as directed.

S&F 4 mm thick sheet glass , figured glass, pinhead type , glazing with oil putty area not exceeding 0.50 Square Metre each pane complete all as specified and as directed.

S & F 6mm thick glass mirror of approved make with mirror screws all sides finished bevelled edging with 20-25mm tappered size completed all as specified and directed.

S & F of 25mm dia decorative/fancy type stainless steel curtain rod with brackets and knobs at both ends as per site requirment incl taking down old existing pipes with accessories. Note : The cost of brackets and knobs is deemed to be incl in the quoted rate. Nothing extra shall be paid on this account.

M&L for PCC (1:2:4 ) type B-1 using 20 mm graded crushed stone aggregate as in levelling courses over RCC roof surface to achieve required slope including rounded or chamfered edges mixed with water proofing compound @ 3% by weight of cement and finishing surface even and smooth using extra cement etc complete all as specified (NOTE :- WPC shall be measured and paid separately as supply only )

M&L cement plaster (1:3) with 10 mm thick to be finished even & smooth without using extra cement mixed with WPC @ 2% by weight of cement, , complete all as specified and directed. (Note : WPC shall be measured and paid separately as supply only).

Taking down complete existing APP membrane any type any layer and M & L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160gm/Sqcm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimentional stability % change = Maximum 1%. (d) Over the membrane provide a finishing with solar reflective bitumen aluminium paint @ 0.10 Kg/Sqm as prescibed by manufacturer. (Note :- Bitumen primer paid separately)

Supply only Bitumen primer for use in waterproofing and damp-proofing treatments all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes , water pipes (150 mm dia ) including all fittings, balance under credit ( measure overall as fixed along the centre line over fitting and accessories ) all as specified and directed.

M&L for 150 mm Internal diameter of pipe Sail-glazed stoneware drain pipes laid in trenches and jointed as specified

S&F 150 mm Bends and taper bends as specified

S&F 150 mm single Y junction as specified

S&F for 110mm bore PVC pipes single socketed Pressure rating @4Kg/Sq cm length "medium grade " with rubber ring joint, fixed to walls with dash ture nut and MS ring (25x6 FI used) bolt at every 1.5 mtrs length complete , incl taking up/down old pipe with all fittings all as specified and directed by Engineer-in-charge.

-'ditto all as per ser item No 69.00 above but laid in trench or in floor

S&F for 110mm bore PVC bends/junction any radius complete all as specified and directed. .

S&F for 75 mm bore PVC pipes single socketed Pressure rating @4Kg/Sq cm length "medium grade " with rubber ring joint, fixed to walls with dash ture nut and bolt at every 2 mtrs length complete , incl taking up/down old pipe with all fittings all as specified and directed by Engineer-in-charge.

-'ditto all as per ser item No 72.00 above but laid in trench or in floor

S&F for 75 mm bore PVC bends/junction any radius complete all as specified and directed. .

Demolition of cement concrete unreinforced of any description and in any position , removal of concrete/ debris and rubbish to a distance n exc 100m as directed by the EIC.

M&L for 18/19 mm thick marine ply bonded with undiluted Phenol Formaldehyde resin, Boiled Water Proof, Specific gravity 0.80 (minimum), moisture content 8-12%, water absorption <5%, provided with and including 1mm thick plastic laminated sheet on both sides of plywood (plastic laminated sheet shall be with decorative choice lamination on one side and other side balancing) (Make of ply : Anchor, Kitply, Century Ply, Green Ply) as in kitchen cabinets, cub board, shelves etc, Fixed with screws to frame work, complete all as specified and directed, Note: Payment for glass panels shall be made for separatly as "supply only".

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) exceeding 1.5 Sqm but not exc 4 Sqm each including complete all as specified and directed.

S&FSolid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing all as specified and directed.

S&F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant as per specifications drawing as directed by the Engineer - in -charge . Material test certificate and authentication should be compulsory provided by the manufacturing company.and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F for Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S&F 100 mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed

S&F aluminum anodised barrel tower bolts of extruded section of size 150 mm length

S&F 150 mm extruded aluminum alloy handles, fabricated type anodised

S&F aluminum anodised sliding door, bolts with hasp and staple ( bolt type ) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy, length of bolts 300 mm.

S&F bands, straps , supports or stays for rain water, ventilating pipes including bolts, clamps, hold fasts etc and similar small articles to Fe-290 Gde-E-165 all as specified & directed.

M&L PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in hold fast, bed plate etc including necessary form work complete all as specified and as directed.

M& L for preparation surfaces of new or previsouly untreated wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S & F for Solid PVC Wall Lining one side prelam consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing.

S & F for 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S & F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets and Supply and fixing hot dipped GI imposed grid with 24mm wide T sect exposed flanges powder coated frame work comprising of main runner made from 0.33 mm thick gs sheet of size 24mmx32mmx3000 mm @1200 mm C/C GI wire 4mm dia fixed by rawl plug, level adjusters and screws etc flush fitting of 1200mm long cross tee interlocked between main runners @ 600mm c/c to form 1200mmx600mm modules cross tee longer than 600 mm to be supported independently 600mmx600mm modules shall be formed by fitting 600mm long cross tee centrally between 1200mm cross tee ,perimeter wall angle shall be GS of size 19mmx19mm and 0.45 mm thick 300mm long including 600mmx600mmx8 to 10mm thick Armstrong gypsum reinforced board complete all as specified and directed.

Supply and fixing suspended false ceiling using (ACP) Aluminium Composite Panel sheet3mm thick and Aluminium rectanqular pipe for grid system fixed to concrete /plaster surface with stainless steel screws incl requisite size of aluminium fillets as directed complete all as specified and as directed.

M&L stainless steel pipe of grade 316-L (Fabricated in any type, design as approved by the GE) as in Staircase railing etc, complete all as specified and directed.

Demolition cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position

Dismantling of water tanks exc 1000 ltr not exc 2000 ltrs and S&F 2000 ltrs PVC water tank, rotational moulded polythene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified.

Dismantling of water tanks exc 500 ltr not exc 1000 ltrs and S&F 1000 ltrs PVC water tank, rotational moulded polythene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified.

S & F 20 mm dia Ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F for 20mm dia gun metal, globe or gate valves, with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S F for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S&F Toughned glass 10 mm thk as in hinged doors , partitions autometic doors and similar work incl cutting to shape , drilling holes requred incl adecute locking system fixed at bottom of door panel.

S&F Toughned glass 12 mm thk as in hinged doors , partitions autometic doors and similar work incl cutting to shape , drilling holes requred incl adecute locking system fixed at bottom of door panel.

Supply only 30 cm long ornemental type stainless steel door handles fixed to 10/12 mm toughened glass door pattern and design as approved by GE.

S & F rolled mild steel in roof trusses(framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing(Beam,tee, angle, channel or flat sections)incl distance pieces, cleats, etc conforming to grade Fe-410W-(Gde E-250 Quality A).

Dismantling of plain/corrugated steel sheeting, any gauge or thickness including Nainital or similar pattern roof covering.

S & F Pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of colour having tensile stength of 550Mpa as in roof coverings/cladding to wall, fixed with self tapping screws as specified.

M&L for PVC tiles/ sheets 1.5 mm thk, laminated plain coloured, marbled mosaic or mottled finish, laid with approved rubber based adhesive in floors surface.

M&L for PVC tiles/ sheets 1.5 mm thk, laminated plain coloured, marbled mosaic or mottled finish, laid with approved rubber based adhesive in vertical surfaces.

S & F for mild steel Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165.

M&L Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment along external wall where the apron is nor provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete

At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ .5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same.

M & L in repairs for point wiring with PVC insulated FRLS unsheathed 1100 Volts grade single core multistranded copper conductor cable 1.5 Sqmm drawn in and including PVC concealed conduit of suitable size of wall/ RCC slab/ ceiling/ colunms/ beams etc with all accessories, fittings, PVC junction boxes etc, with suitabe sunk pressed steel boxes for modular fittings not less than 1.6 mm thick, including Modular cover plate of suitable size etc with necessary fixing accessories and earth continuity conductor cable of 1.5 Sqmm size connected to common earth and earth dolly including 1.6 mm thick pressed steel terminal boxes concealed in wall mounting switches / sockets / fan regulators fixed with Cadmium plated machine screws including taking down old us wiring, fittings etc complete all as specified for one light / fan / bell point controlled by one switch. Note : 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit. Make of conduit :- Sudhakar/ Precision/ Diamond, Make of wire :- Finolex/ Havells/ Polycab/ KEI/ Benlo

-Ditto- all as per item No 114 above but for one 6A 2pin/3pin socket out let multipurpose on the same board with other switches.

-Ditto- all as per item No 114 above but for one 6A 2pin/3pin switch socket out let multipurpose on independent Board.

All as per item No. 114 above but wiring complete with 2.5 Sqmm for 3 pin 16A socket multipurpose on independent board

S & F in repairs modular type 6A one way SP switch 1 module confirming to IS: 3854-1997 with finger proof terminal complete all as specified and directed.

S & F in repairs modular type 2/3 pin 6 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree)

S & F in repairs modular type 2/3 pin 16 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree)

S & F in repairs modular type 16 A one way SP switch 1 module confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree)

S & F in repairs modular type 120W step fan regulator of 2 module size conformng to IS: 11037-1984 complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree)

S & F in repairs ceiling rose three terminal, 230 Volts PVC / Polycarbonate body, complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree)

S & F Modular Blank plate 1 module suitable for Modular switch boards all as specified and as directed

S & F Modular cover plate 12 modules complete all as specified and directed.

S & F Modular cover plate 8 modules complete all as specified and directed.

S & F Modular cover plate 6 modules complete all as specified and directed.

S & F Modular cover plate 4 modules complete all as specified and directed.

S & F Modular cover plate 3 modules complete all as specified and directed.

S & F Modular cover plate 2 modules complete all as specified and directed.

Supply & Fix LED based alluminium batten type fitting of capacity 20W, operating on 230V, 50Hz, AC Supply having luminous efficacy of not less than 100 lumens/watts, CCT 6500K, P.F>0.9, 2.5 KV surge protection, 4-feet long, housing made out of engineering plastic with decorative end caps elegently designed complete all as specified. Make - Bajaj/ Wipro/ Jaquar/ Halonix

S & F in replacement of 36 W ceiling recessed light of size (2x2 ft) having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed. Make : Bajaj/wipro/Jaquar/ Halonix

Supply and fixing in replacement of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including provision with three core flexible copper conductor cable of suitable size and PVC square blocks complete all as specified and directed. Make - Bajaj/ Wipro/ Jaquar/ Halonix

S & F LED light fitting 1X10W Bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make - Bajaj/ Wipro/ Jaquar/ Halonix

S & F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting complete all as specified and directed. Make - Havells/ Anchor/Jaquar/ Halonix

S & F LED Light Bulb 9 watt, Pin type of white colour, 230 V complete all as specified and directed. Make - Bajaj/ Orient/ Philips/Jaquar/

Supply and fix in repairs high speed Ceiling fans complete with aluminium blades, down rods, PVC Canopy and accessories, white in colour 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value min 6.00, BEE Five star rated with brushless direct current motor(BLDC) without remote complete including taking down old unserviceable fan to MES store all as directed by Engr-in-Charge. Make : Havells (Efficiencia Neo (BLDC 26 W) /Orient (FALCON 400) / Bajaj (ENERGOS 28) Note : Fan Regulator will be paid seperately under respective itme of BOQ and Unserviceable ceiling fans shall be deposit to MES store.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300 mm sweep with, blades, and frame and louvers complete all as specified and directed. Make :- ALMONARD / ORIENT/Havells/ABB

S&F modular type 3/5 pin socket with one single pole MCB 20 Amp 230 Volts complete all as specified including concealing in wall suitable for Geyser, AC and Domestic appliances complete all as specified and directed. Make - Havells/ Legrand/ Schneider/ABB

Supply & fixing MCCB 4 Pole,415 V, fixed type, 125 Amps with breaking capacity 16 KA including connecting up electrically with proper lugs glands and including all necessary fittings complete all as specified and directed. Make -Havells/Indoasaian/Legrand/ABB/Schnider

S & F MCCB TPN DB, 4 way TPN (vertical type), double door, 415 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections complete all as specified and directed. Note: Quoted rate shall be deemed to include for provision of copper bus bar of 200 Amps rating. Make -Havells/Indoasaian/Legrand/ABB/Schnider

S & F MCB DB, 12 way, SPN, double door, 240 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections including taking down old us DB complete all as specified and directed. Make -Havells/Indoasaian/Legrand/ABB/Schnider Note: Quoted rate shall be deemed to include for provision of copper bus bar of 200 Amps rating.

S & F MCB SPN 40 Amps, 240 / 415 Volts, 'C' Series, 50 Hz, 10 KA Breaking capacity complete all as specified and directed.Make -Havells/Indoasaian/Legrand/ABB/Schnider

Supply and fixing SP 63 Amps rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.Make: schneider,Legrand,Havells,indoasian

-Ditto- all as per item No 30 here-in-before but for SP 5 to 32 Amps, 240V, 10KA 'C' curve miniature circuit breaker (MCB) complete all as specified and directed.Make: schneider,Legrand,Havells,indoasian

M&L for sub main wiring with two single core 6.0 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC concealed conduit with and including PVC insulated 6.0 Sqm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly including taking down old unserviceable submain wiring complete all as specified and as directed Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.Make: Benlo,Anchor panasonic,finolex,Havells

M&L for sub main wiring with two single core 4.0 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC concealed conduit with and including PVC insulated 4.0 Sqm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly including taking down old unserviceable submain wiring complete all as specified and as directed Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.Make: Benlo,Anchor panasonic,finolex,Havells

M&L for sub main wiring with two single core 1.5 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 1.5 Sqm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly including taking down old unserviceable submain wiring complete all as specified and as directed Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.Make: Benlo,Anchor panasonic,finolex,Havells

S&F in repair/replacement of building Security light fitting 35 Watt made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP66 protection and impact resistance of IK07 including fixing arrangements and taking down old rusted bracket fittings complete all as per directed by Engr- in – charge.Make: jaguar,wipro,bajaj,halonix

M & L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion per SSR specification all as specified and directed. Note : A sum of Rs 53,847.00 towards sch of credit shall be deducated to arrive the contract sum.

Parmatma Enterprises (BID ID -3102142)

M/s Mukesh Engineers (BID ID -3104093)

Vishal Builders (BID ID -3104688)

Joy builders (BID ID -3104608)