Construction of RCC office building for DICC Majuli at Garamur Dist Majuli with future provision for G plus 1

Amount

CIVIL_WORK: Providing cast in-situ manually driven reinforced cement concrete piles of using required grade of cement concrete of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings. Reinforcement to be measured and paid seperately as per item no. 21.4.1 (C) UNIFORM PILE e) Pile Dia 450 mm (i) Upto 10 M

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) (A) TMT bar made of Primary producer (From Primary producer).

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified. (b) Other than Guwahati city

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 3 sand :6 coarse aggregate by volume.

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (I) Using Mixer Machine. Using admixture, plasticiser (b) M20 grade concrete or Prop. 1:1.5:3

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work.

Providing form work of ordinary timber planking and removal of the same in edges of slabs and breaks in floors and walls etc. of in-situ reinforced concrete works upto first floor level. (a) Thickness not exceeding 200mm

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a) Brick on flat soling.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (a) In Sub-structure upto plinth level including dewatering if necessary. In proportion 1:4

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately). (A) 112mm thick brick wall. (a) In cement mortar in proportion 1:4

Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. (a) 100mm thick

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. (b) 20 mm thick

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). (b)Executiverange Somany/ Orient/Nitco/Asian Make. (ii) Of size 250mmx350mm and above

Providing vitrified floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) (a) Normal range Marbonite/ Make (ii) Of size 600mm x 600mm and above

Providing polished granite slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). (ii) Executive Quality

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (i) Normal range (Sizes 300 mm x 300mm and above). (a) Orient made: Galaxy Brown, Galaxy creama, Galaxy Pink, Galaxy Green, Pulsar Beige, Pulsar Blue, Pulsar Dove, Pulsar Pink, Burj Brown, Burj Green, Burj Slate.

Providing polished SUNROCK-Hi CTS/ MULTIWYN tiles of approved quality, size, shape and thickness not less than 18mm on floors and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). SUNROCK Hi CTS TILES (ii). Old Castle (455x455) mm

20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. b) In cement mortar 1:4

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) suspended ceiling which includes G.I. perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I. intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25mmx10mmx0.55mm thick fixed to soffit with G.I.cleat and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two equal flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 298mm c/c. Then 12.5mm thick square edge Fulltone/ Sundance/ Cratone/ Louvertone/ Textured. Gypboard panels of size 595mmx595mm (conforming to IS:2095-1982) is then screw fixed to ceiling section with 25mm long drywall screws at 290mm c/c. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally, the boards are to be jointed and finished so as to have a flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, joint paper tape and two coats of drywall topcoat suitable for Gypboard complete at all levels as specified and directed. (For light fittings, grill diffusers etc. Cut out to be made with the frame of perimeter channel supported suitably and measured and paid separately as and where necessary). (Glass wool to be measured and paid separately). (C)M/F Frame Work with Acoustic Type Fissured Gypboard (Cratone) Tiles (NRC value 0.57 with 50mm glass wool mat backing) 12.5mm thick.

Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid separately.) (iv) 0.60 mm thick

Grading roof for water proofing treatment with (a) Cement concrete 1:2:4 (i) 1 cement: 2 coarse sand: 4 graded stone agg. 20 mm nominal size)

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. (a) Decorative type face panel and block board core. (i) 40 mm thick.

Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ openingwith M.S. flats at required spacing in frame all round, squre or round M.S. bars with round headed bolts and nuts or screws. (I) Plain grill (c) Fixed to Brickwork/P.C.C/R.C.C.

Providing, fitting and fixing anodised aluminium sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels. (a) 2 Track sliding window (iii) 5mm coloured glass

Providing, fitting and fixing anodised aluminium sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels. (b) 5 Track sliding window. (iii) 6mm coloured glass

Providing, fitting and fixing anodised aluminuim framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete etc complete as specified and directed by the department at all levels. (b) with 10 mm thick toughened glass

Providing and fixing anodised aluminium framed single leaf door of approved brand with styles size 45mm x 48mm x 3.2mm, top rails 50mm x 45mm x 2.5mm, lock rails 48 mm x 45mm x 2.5mm, bottom rails 100mm x 45mm x 2.5mm fitted with tapper clips of size 20mmx15mmx1.2mm complete with automatic hydraulic floor mounted door closure, butterfly type handles, special cylindrical locks, concealed type tower bolt,neoprene dryset rubber gusket, etc.complete as directed by the Department at all levels. (i) 5mm thick frosted glass and 12mm thick prelaminated board

Providing, fitting and fixing anodised aluminium partition walls of standard sections of approved brand, joints mitred and welded (manufactured to relevant I.S. specification) and providing and fitting angle cleat, rubber gasket, bolting device screws etc. at all levels. (i) Partly 6mm thick glass panes and 12mm prelaminated ply board

Providing, fitting and fixing PVC door frame of Duroplast make DPF-5060 make suitable for DPS-3720 made from extruded PVC multichamber hollow section having dimensions of 50mmx60mm (Toletance + 1mm). Horizontal and vertical sections shall be joined by steel screws after inserting M.S. tubular rectangular galvanised L-shaped brackets of size 100mmx100mm or plastic brackets of size 75mmx75mm with metred cut at the corners. Hinge side of the frame shall be reinforced with M.S.Tubular section of size 40mmx20mm. The frame will be fixed to the column/ stiffner/ wall with the help of 3 nos 75mm long and 4mm dia steel screws and expandable fastners on each side of the door frame complete in all respects as sepcified and directed at all levels.

Providing, fitting and fixing PVC Door shutters of 37mm (single panel seamless finish) of Syntex make, at all levels made of extruded sections in the configuration of 'A'.The overall dimension is 37mm x 90mm, with usual process variation having a wall thickness of 2mm with a variation of +0.03mm provided with all plastic reinforcement to avoid rusting. The shutter frame is mitred and joined at the corners by means of stainless steel screws.The corners of the shutter frame are being reinforced by polymeric reinforcement of the size 125mm x 250mm and the lock rail is reinforced by 45 x18 x255 size reinforcement. The lock rail is made of extruded hollow PVC section in the configuratino of 'H' having wall thickness of 2mm with a variation of +0.03mm and effective dimension of 37mm x 105mm. The infill is made of multi-chambered hollow PVC extruded panel having an effective dimension of 762mm x 20mm or less as per requirement with usual process variation having a wall thickness of 1mm +0.03mm.The entire door shutter should be provided with S.S. screws at appropriate places for rust free quality. (Door fixtures and fittings to be measured and paid separately.)

Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac

Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. (a) With ready mixed "red-lead/ red oxide" primer.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac). (i) Surfaces over 100mm in width or girth. b). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Finishing old / new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats)

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodised to bright natural matt & satin finished) (a) Sliding door bolts (i) 300mm x 16mm.

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodised to bright natural matt & satin finished) (b) Tower bolts (i) 300mm x 12mm

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodised to bright natural matt & satin finished) (c) Door handles (iii) 150mm

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodised to bright natural matt & satin finished) (i) m) Mortice lock vertical type. (iii) 100mm (Godrej with handle (6 lever)

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodised to bright natural matt & satin finished)(t) Door stopper with rubber stopper.

Providing, fitting and fixing Floor Spring of various weight & type UL listed and fire rated good quality depending on the door specification. Types like single speed, Double Speed, Heavy Duty etc are available and as directed & specified by the department. (A) Architectural Rangeb) Heavy duty Floor Spring D100

Supplying, fitting and fixing drapery rods along with all accessories in doors, windows and other openings complete as specified and directed by the departmentb at all levels. (A) MAC Drapery rod (vi) Silk line

Supplying, fitting and fixing MAC blinds horizontal and vertical complete as specified and directed by the department at all levels. (A) Vertical blinds (b) Blackout (iii) 75 mm

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level). (a) From Primary Producer: TATA/ SAIL/Esser Steel/ Jindal steel/ Shyam Steel/ RINL. (i) TMT Corrosion resistant steel (CRS) reinforcement bar

ISI approved M S Rod

Providing, fitting, hoisting and fixing of roof trusses including purlins fabricated using MS circular hollow section conforming to relevant I.S. code, as per approved design and drawings including providing M.S. cleats, base plates, bolts and nuts and one coat of red oxide Zinc Chromate primer and two coats of approved enamel paints complete including fitting necessary cleats etc. for fixing ceiling joists as per design and drawing as directed. Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S. code 4923 : 1997

Providing and fixing in position collapsible M.S. shutters with vertical channels 20mmx10mmx2mm braced with flat iron diagonals 20mmx5mm size with top and bottom rails of T-iron 40mmx40mmx6mm with 38mm dia steel pulleys complete with bolts and nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/ 1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, head and steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be filled up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works etc. complete as directed by the department for all levels. (P.C.C. to be measured and paid for separately). (b) 1.60mm thick sheet. (iv) Size 125mm x 60mm (Double rebate)

Providing fitting and fixing Godrej SS 304 grade railing with pipes/glass for different staircase, cutout areas, balcony, etc with complete installation, Acrylic finish, etc which is fitted with mid pipes and top pipes of good quality steel. Moreover, depending on the requirement glass panels can also be fitted on specific railings. Good quality screws are provided for fixing up the railings.

Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Providing drain with cement concrete (1:3:6) 10cm thick sides 10cm thick bed over brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. (i) 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Pre construction anti - termite treatment by applying in the entire levelled area after plinth filling and before laying floor by applying the emulsion @ 5 (five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. (a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

SANITARY_WORKS -Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) A) Parryware make (a) White (i) Universal Closet S Trap (Cat No.C0271) (Anglo Indian) (inclusive of seat cover)

Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) A) Parryware make (b) Coloured (ii) Combination Closet S Trap (Cat No.C0205) (inclusive of seat cover)

Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) i) Parryware make a) White (i)Economy Single Flush (Cat No.C8090/C8055)

Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) i) Parryware make b) Coloured (ii) Deluxe Single Flush (Cat. No. C8091/C8057)

Providing fitting and fixing vitreous china flat back type lipped front urinal basin with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. (A) Parryware Make (a) White (ii) Aquaseal (Cat. No.C0508)

Providing fitting and fixing vitreous china flat back type lipped front urinal basin with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. (A) Parryware Make (b) Coloured (ii) Aquaseal (Cat. No.C0508)

Providing fitting and fixing vitreous china squatting plate urinal with automatic flushing cistern with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. (A) Parryware Make (i) White (Cat. No. C0503)

Providing fitting and fixing vitreous china squatting plate urinal with automatic flushing cistern with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. (A) Parryware Make (ii) Coloured (Cat. No.C0573)

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) 1.13.1 PEDESTAL BASIN (with pedestal) (A) Parryware Make (b) Coloured (i) Cascade NXT 550 x 440 with long Pedestal (Cat. No.C0404/C0380)

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) 1.13.2 Basin (without pedestal) (A) Parryware Make (a) White (i) Star Basin 550 x 400 (Cat. No.C0450)

Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately (B) Nirali (ix) Grace Plain Jumbo (Bowl Size - 610 x 460 x 254) Glossy

Providing fitting and fixing Mirror with plastic frame of size 500x400mm complete as directed and specified.

Providing, fitting and fixing CP soap tray / soap dish complete as directed and specified. (i) Jaquar Make (a) Continental (Cat.No.ACN-1331N)

Providing, fitting and fixing CP towel rail complete as directed and specified. (a) Jaquar make (iii) Queen's (600mm long) (Cat.No.AQN-7711)

WASTE COUPLING - Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified. (a) Jaquar Make (i) 32mm (HT/FT) (Cat.No.ALD-705 / 709)

PVC PIPES, BENDS, JUNCTIONS, TEES, ETC. - Supplying, fitting and fixing I.S.I marked or similar approved PVC pipe including bolts and nuts and other fittings as required and complete at all levels including below G.L as directed and specified. (a) In exposed surfaces or in trenches. (i) 110 mm

Supplying, fitting and fixing I.S.I marked or similar approved PVC pipe including bolts and nuts and other fittings as required and complete at all levels including below G.L as directed and specified. (a) In exposed surfaces or in trenches. (iv) 75 mm

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia.

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. (ii) 110mm dia. PVC cowel of ISI make

C.P. Grating (ii) 110mm dia

Providing fitting and fixing 450mm dia. 90mm thick C.I. Man hole cover and frame of 25 Kg. weight complete as directed and specified

Construction of filter bed in soak pit including earth work in excavation of soil and then filling up of the trench with brick bats/Charcoal covered with earth over a layer of A.C. plain sheet above brick bat filling complete as directed. (sizes of soak pit may vary depending on the sizes and capacities of the septic tank as well as the number of users as mentioned in the table.

Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.

Construction of Septik Tank (50 users)

INTERNAL WATER SUPPLY: Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. (B) Concealed by chieselling or breaking brick wall/ C.C. wall/ R.C.C. wall and making good to the damaged structure. d)25 mm dia

Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. (B) Concealed by chieselling or breaking brick wall/ C.C. wall/ R.C.C. wall and making good to the damaged structure. f)15 mm dia

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) (VI) Sona brand. ii) Bib Cock Long Body,Code.No.RG-5022

Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) (IV) Sona brand (b) 15 mm dia Concealed stop cock

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. (I) SONA make (b) Heavy type

Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) (I)Sona brandb) Sink cock J spout

Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed. a) 50mm dia

Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed. c) 25 mm dia.

Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed. e) 15 mm dia.

EXTERNAL_WATER_SUPPLY_WORKS - Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed B) uPVC pipe with uPVC fittings ( Using uPVC high pressure pipe) (Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipe) iv)20mm diameter

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed B) uPVC pipe with uPVC fittings ( Using uPVC high pressure pipe) (Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipe) iii) 25mm diameter

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed B) uPVC pipe with uPVC fittings ( Using uPVC high pressure pipe) (Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipe) vi) 50mm diameter

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes. (I) 1000 Lt capacity (a) Sintex make

Labour for erecting and placing PCVC Tank complete as directed. (c) 1000 litre capacity

DEEP_TUBE_WELL: Preparing of site for placement of drilling rig including excavation of mud pit, circulation drain,collection chamber etc.all complete as directed.

Movement of rig to drilling site including cost of POL all complete as directed.

Transportation of ancilary equipment, camp materials, welding set, rig accessories etc. including cost of POL all complete as directed. (a) For less than 100.00 Km

Transportation of ancilary equipment, camp materials, welding set, rig accessories etc. including cost of POL all complete as directed. (b) Beyond 100.00 Km

Transportation of all store materials like pipe, strainer, cone, socket, clamp, bentonite, etc. including cost of POL all complete as directed. (a) For less than 100.00 Km

Transportation of all store materials like pipe, strainer, cone, socket, clamp, bentonite, etc. including cost of POL all complete as directed. (b) Beyond 100.00 Km

Transportation of air compressior of Kirloskar make 540 CFM, 10.5 kg./sq cm with all accessories including the cost of POL all complete as directed. (a) For less than 100.00 Km

Transportation of air compressior of Kirloskar make 540 CFM, 10.5 kg./sq cm with all accessories including the cost of POL all complete as directed. (b) Beyond 100.00 Km

Construction of temporary accomodation and low cost sanitary facility for drilling staff including cost of camp materials viz. cots, table, chairs, umbrellas, dresses, safety halmets, etc. and dismentling the accomodation after completion of the work all complete as directed.

Providing water supply facilities at drilling all complete as directed. (a) By installing 1 No. of Singur Hand Pump.

Drilling with drilling bit in over burden portion of soil formation including of soil sample at every 3m depth of wherever there is change of strata in sample box with distinguish mark up to depth of rock formation and withdrawing the drill bit for lowering as directed with 245mm/305mm dia drill bit.

Casing and sinking/lowering of MS pipe 200mm dia including cost of pipe and labour charges for cashing, welding the joints and sinking by drilling Rig in position all complete.

Developing of the DTW with air compressor, make Kirloskar/Cumins all complete as directed.

Supplying and packing pea gravel around the periphery of casing including screening, washing etc. all complete as directed.

Supplying, fitting, fixing MS clamp of size 15 mm thick and 150 mm width having projection of 300 mm and three holes of 20 mm dia for clamping the plates by 16 mm dia hexagonal bolts of length 75 mm and nuts on both sides encircling the column pipe including two coat of enamel paint over one priming coat of different dia all complete as directed and specified. (c) 200 mm dia

Supplying, fitting and fixing suction pipes (plain/ bevel ended), conforming to relevant IS codes of practice including supplying and fitting of accessories, lowering of assembly pipes concentrically in the casting pipes complete as directed. (I) G.I. Pipe (a) TATA/SAIL (medium) (sockets should be welded to the pipes) (iv) 50 mm diameter

Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. (A) Exposed or in trenches SUPREME/ PRINCE/ SFMC BRAND or other equvalent approved brand (High presure pipe Sch-40) (v) 50 mm diameter

Supplying including installation of submersible type water supply fitting & fixing of water supply motor pump set with all accessories including panel board on C.C. Foundation of Proporation 1:2:4 jammed with M.S. Nuts and Bolts , wire rope submersible cable without suction G.I. Pipe including making necesary connection etc as reqd. complete . (4) 3 H.P. Three Phase

INTERNAL_ELECTRIFICATION: Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 20mm dia 2mm thick / heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including 6 Amp flush type switch/ bell push (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) with phenolic laminated sheet cover ,ceiling rose (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) etc. complete (ii) Medium Point upto 6.00 metre length.

Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 20mm dia 2mm thick / heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including 6 Amp flush type switch/ bell push (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) with phenolic laminated sheet cover ,ceiling rose (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) etc. complete (iii) Long Point upto 10.00 metre length.

Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete, when placed elsewhere. (ii) Medium Point upto 6.00 metre length.

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch ( Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) (ii) Medium Point upto 6.00 metre length.

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch ( Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) (iii) Long Point upto 10.00 metre length.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system.With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. cable in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Supplying and fixing of Jaquar or equivalent Philips/ Wipro LED round fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required. ECBC.3.18.2 LED Round Light,6W

Supplying and fixing of bulk head fitting suitable for CFL lamp complete with all accessories including 20 watts CFL lamp and connection as approved by the Deptt.)as required. necessary connection as approved, specified and directed by the deptt.

Supplying and fixing of Call bell ( Buzzer ) including 5/ 6 amp capacity button piano type bell push switch including connection as approved by the Deptt.)as required.

EARTHING: Installation of earth station with 40mm dia and 4.5 mtr. long GI pipe with necessary GI reducing socket 40mmx20mm size locking arrangement with hinged cover plate, funnel, GI nuts, thorough bolts etc.for putting pipe and refitting with necessary enclosure on the top etc. as required complete.

Extra for using salt 5Kg and charcoal 64 Kg. for pipe earth electrode as required.

Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator]. 27.1.3 Premium model 1400 mm Sweep. (ORIENT PSPO make) /Premium model 1400 mm Sweep SS-390 Deco. Havells make)

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. 27.2.1 Domestic 27.2.1.6 Ventilator DX 250 mm sweep Louver type (ORIENT make), Brisk Air 250 mm sweep Louver type/ Trans Air 150 mm sweep (Crompton make), Ventil Air DX 150 mm sweep Louver type (Havells make)

Supplying including fitting fixing of ceiling fan regulator 27.6.2 Electronic tipe

Supplying with fitting and fixing sheet steel, phosphatised, powder painted Single door surface mounting vertical TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar 125A and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 15.19.1 ABB, Schneider MG, legrand, Hager make) 15.19.1.1 4 way TPN (8+12) single door

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 16.1.1 B Series (Schneider MG, legrand, Hager make) 16.1.1.1 6 to 32A

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/Havells/RPG/CCI/Polycab/ Gloster/ Finolex make) . 32.1.3 3 & 1/2 Core A2XFY 32.1.3.6 120.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supplying with installation testing and commissioning of Hi -- wall 5 STAR rating non ducted split type air conditioner of the following capacity with cordless remote complete with copper pipe and electrical connection cable, as approved by the Deptt.)up to 5 m between the room unit and out door unit as directed by the department. ECBC 7.4.1 2) 2 Ton Capacity

Supplying with fitting and fixing Voltage stabilizer of the following specification complete including making necessary connection as approved, specified and directed by the deptt. (SKYLAND / Vee-Dee / V GUARD / VERTEX/ INDO/ VENUS make) 31.1.8 5.0 KVA Automatic Input 90-280 V Out put 200-240 V

External Electrification Works: Supplying and installation and commissioning of vermin and dust proof totally enclosed double door cubical type compartmental floor mounting panel board of size 1.20 m ×1.00 m ×0.50 m made of 16 SWG1.66mm) thick CR sheet and 35 mm × 35 mm × 6 mm size angle and 35 mm ×6 mm flat iron having 4 nos legs at the bottom and G.I. Sheet reefing on the top complete painting with 2 coats of red oxide metal primer and 2 coats of enameled paint. The panel board is to be erected in 1:3:6 RCC pole foundation including excavation of trench and brick soling etc. complete neatly internal wiring done as specified and directed by the department comprising of the following electrical items. 1. 40 Amp 4 pole 415 Volt 50 Hz MCCB as incomer - 1 no 2. 32 Amp 2 pole open execution with HBC fuse SDFU unit as outgoing - 3 nos. 3. 25 mm × 5 mm size 4 strip copper Bus-Bar- 1 set 4. 40 Amp 4 pole ON-OFF poser contactor - 1 No. 5. Surface mounting timer switch - 1 No. 6. 63 Amp bakelite HBC fuse kit-kat - 3 Nos 7. 0-40 Amp electro-mechanical counter display 3 Phase 4 wire electronic hybrid energy meter

Supplying with fitting & fixing of the following integral type street light luminaries complete and consisting of single piece integral epoxy gray powder coated dia cast aluminium housing gasket, pot optic reflector, cast aluminium frame from heat resistance toughened clear glass cover and accessories such as Condenser, lamp Holder, Ballast, lamp etc. in the existing pole including making necessary connection as approved by the Deptt.)with 2× 2.50 sq.mm F.R. multistrand and P.V.C. insulated single core copper cable as specified and directed by the department. 25.2.2 Philips make) Cat No.SRX086 1xSON150W For Lamp 1xSON/SONT150W/ / Havells make): LHYW00115099 For lamp 1x150W SON-T.

Supplying including fitting and fixing of Hot Dip galvanised arm bracket for installation of luminaries. Header with top cap 300 mm long pipe of thickness 3 with arrangement to fix on pole top with 3 Nos. of bolts. i Armed of required length size 48.3mm out side dia x 3.25mm thick (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make) Stiffener plate from arm of the following types : 37.2.1 Single arm bracket 1000mm long for 3m to 10 metre. Poles.

Supplying, erection and commissioning of the following specification as per IS:2713 : 410 SP hot dip Galvanized Steel tubular pole manufacturing out from electrically welded in 3 (three section having a base plate including providing all required building materials as directed and specified by the deptt. (BANSAL/SRP / Valmont / PARUTHI ENGR make) 36.34.9 410 SP 43 Length of pole = 10.00 metre., Length of sections, Bottom = 5.20 M, Middle = 2.40 M, Top = 2.40 M, Out side dia. & Thickness Bottom = 165.10 x 4.50 mm, Middle =138.70 x 4.50 mm, Top=114.3 x 3.65 mm

Supplying and fixing of 11 KV 150 A D.O. fuse set complete as required and as directed by the department.

Supplying and fitting fixing of galvanised channel of 100 mm x 50 mm x 65 x 2200 mm long complete with clamps ,blots, nuts etc. as required and as directed by the department.

Supplying and fixing of 11 KV 5 KA Lighting arrestor (Poly) set complete as required and as directed by the department.

Supplying and erection of 11 KV Pin insulator (Poly) with G.I.pin, blots and nuts coach screw etc. as required and as directed by the department.

Supplying including installation of 4' dia. C.I. earth pipe complete as required and as directed by the department.

Extra for using salt (5 K and Charcoal (96 K in G.I./Copper plate Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the deptt

Supplying and fixing of 11 KV 400 A Gang operated switch with all accessories complete as required and as directed by the department.

Supplying & laying of 8 SWG Copper earth drawn through 15 mm dia. Medium quality G.I. pipe from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supplying and fitting fixing of galvanised L.T. T cross arm complete with clamps ,blots, nuts etc. as required and as directed by the department.

Supply including fitting and fixing of Resin Cast type outdoor end cable Termination Kit for 3 Core/1.1 KV PILC cable (MS - SE For the following sizes including testing and commissioning as specified and directed by the Deptt.. 34.17.1 50.00,70.00 & 95.00 Sq.mm., 3 Core cable.

Supply including fitting and fixing of Resin Cast type outdoor end cable Termination Kit for 3 Core/1.1 KV XLPE cable for the following sizes including testing and commissioning as specified and directed by the Deptt. 34.22.1 50.00,70.00 & 95.00 Sq.mm., 3 Core cable.

ASEB LOAD SEQUIRTY and Service Connection Charge

RCC_DRAIN: Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a) Brick on flat soling.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 3 sand : 6 coarse aggregate by volume.

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (A) In substructure up to plinth level. Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. (b) M20 grade concrete or Prop. (1:1.5:3)

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work.

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (b) Other ISI approved TMT reinforcement bar (SAI/BISCON/THERMAX). (For Assam Type Bldg., drain works, retaining wall & boundary wall etc. .

APPROACH & INTERNAL ROAD WITH PAVER BLOCK: Providing SUN ROCK HIGH CTS /DEVI paver block/tiles of concrete grade M30 or above of approved quality, size, shape of specified thickness over a levelling bedding layer of 30mm compacted sand over a base course including cutting where necessary finished with spreading, sweeping jointing sand and compacting the pavers using vibrating compactor as specified and directed. (a) 80 mm thick).

Construction of Granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per Clause 401 of MoRTH specifications (including carriage) (including cost of testing of materials at site and laboratory as directed by the deptt.)

Fire Fightening Work: Supplying, installing , fixing of dry chemical powder fire extinguisher conforming to IS: 2171 with ISI mark and CO2 cartridge will be conforming to IS : 4947 with IS: 4308 with ISI mark , Powder will be confirming to IS: 4308 with ISI Mark(10 Kg) BRAND: FIRESTOP/FIREND/ FIRE SHIELD/GETECH/MINMEX

Landscaping Works: Supplying and planting of ornamental trees (1'-0" height sapling) including pit making ( 60 cm x 60 cm x 60 cm ), filling the pit with appropriate soil media, manure and fertilizers as per specification and necessary maintenance for a period of one year from the date of planting complete as specified and directed. SHADE TREE (A) Neem / Madhuri / Silikha / Amlakhi

Supplying and planting of ornamental trees (1'-0" height sapling) including pit making ( 60 cm x 60 cm x 60 cm ), filling the pit with appropriate soil media, manure and fertilizers as per specification and necessary maintenance for a period of one year from the date of planting complete as specified and directed. SHADE TREE (D) Debadaru

Supplying and planting of ornamental shrub (below 1’-0” height) including pit making (60 cm x 60 cm x 60 cm), filling the pit with appropriate soil media, manure and fertilizers as per specification and necessary maintenance for a period of one year from the date of planting complete and directed. (D) Thuja.

Half brick circular tree guard internal diameter 1.25 m and height 1.2 m above ground and 0.02 m below ground bottom two coarse laid dry and top three coarse in cement mortar 1:6 and the intermediate coarse being in dry honey comb masonry as per design complete.

Glow Sign Board: Supplying, fitting & fixing of Glow Sign board made on MS frame and aluminium sheet and side with no. 18 backelite sheet with solvent printing, electrification, lighting, making necessary connections etc. as required complete and as directed by the department.

Computer Lane: Supplying with fitting and fixing of CAT 6 RJ-45 Computer jack in one module, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supply, installation, testing and commissioning of following LAN networks equipments. SB. 16.4.1 Solid Copper Cable Cat 6, 4 pair, UTP - 305m SCHNEIDER/LEGRAND or equivalent make as approved by Deptt.

Supply, installation, testing and commissioning of following LAN networks equipments. SB. 16.4.2 Patch Panel Cat 6 UTP Keystone -24 Port- Loaded SCHNEIDER/LEGRAND or equivalent make as approved by Deptt..

Supply, installation testing and commissioning of following LAN networks equipments. SB. 16.4.4 Patch Cord Cat 6 UTP Gray 2m - Moulded SCHNEIDER/LEGRAND or equivalent make as approved by Deptt.

Supply, installation testing and commissioning of following LAN networks equipments. SB. 16.4.5 Cat 6 Keystone UTP Jack with Dust Cover-White SCHNEIDER/LEGRAND or equivalent make as approved by Deptt.

Supply, installation testing and commissioning of following LAN networks equipments. SB. 16.4.6 O. F. Cable 6F Loose Tube ( Unitube ) Type CSTA SM SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Supply, installation testing and commissioning of following LAN networks equipments. SB. 16.4.16 DIGILINKL/ LEGRAND OR equivalent 24 Port 10/100/1000Mbps Layer 2 stackable Switch with 4 Gigabit Combo Ports.

15 KVA On-Line UPS System (Orion or equivalent make as approved by the Deptt.) with PWM-IGBT technology 360V AC Input (300V – 470V A 3 Ph input- 1 PhoutputWith Isolation Transformer 12KW output with 0.8 output PF 120 min backup using SMF battery

APW Cyber Rack Server and Networking Rack APW President Enclosure, 800mmW CYBERACK 42U / 1000mmD (CRCA Steel Frame with Aluminium Profiles & 2 Nos. of Removable Side Panels with following items: - Top cover with cable entry -1no. - Bottom cover with cable entry -1no. - 19” Mounting Angles – 2 pairs. , Vertical Cable Manager 2U Front and Rear, Finish : Powder coated to 80 microns; Matt finish. colour : BLACK with , Load rating capacity -- 500 kgs., Front side vented glass door and rear full perforated steel door with locks. "PDU 10*5/15A - 01 Nos Fan Housing Unit with 4 Fans - 01 Set Mounting Hardware (Set of 20) - 1 Set Castor with Brake - 2 Nos. Castor without Brake - 2 Nos. Earthing Kit - 01 Set"

FURNITURE : GENERAL MANAGER`S TABLE MODEL: HT 501-A Main Table Size: 2200W x 800W x 780H MM Side Unit Size: 1010W x 500D x 650H MM Table top: 50mm thick prelaminated particle board plus medium density board of melamine surface finish. Wire manager: Flip up included. Colour: Dark walnut. Make: Featherlite

FM TABLE MODEL: HT 531 Main Table Size: 1600W x 750W x 780H MM Side Unit Size: 905W x 440D x 650H MM Table top: 54mm thick prelaminated particle board plus medium density board of melamine surface finish. Wire manager: Flip up included. Colour: Dark walnut. Make: Featherlite

ADCI TABLE MODEL: V-MT 1575 Size: 1500W x 750W x 750H MM Side Unit (Credenza) Model V-CZ Size: 1200W x 450D x 750H MM Colour: Dark walnut. Make: Featherlite

ASSISTANT MANAGER MODEL: V-MT 1575 Size: 1500W x 750W x 750H MM. PADESTAL UNITS MODEL V-2D1F Size: 400W x 435D x 640H MM Colour: Dark walnut. Make: Featherlite

EO and HA TABLE MODEL: V-MT 1275 Size: 1200W x 750W x 750H MM. PADESTAL UNITS MODEL V-2D1F Size: 400W x 435D x 640H MM Colour: Dark walnut. Make: Featherlite

JUNIOR ASSISTANT TABLE MODEL: V-MT 1275 Size: 1200W x 750W x 750H MM. Colour: Dark walnut. Make: Featherlite

CONFERENCE_TABLE: MODEL FST 54015 SIZE:5400 x 1500 x 750 ht. Specifications: Table top - 25mm thick Pre-laminated particle board finished with 2mm PVC edge lipping. Under Structure - Gable end and modesty panel. Wire Management -Vertrebra for wire uptake to MS cable tray from floor and 3 nos 300 mm aluminium flip up for switch access. Make: Featherlite

STORAGE: MODEL VERSALINE STORAGE UNIT Specifications: The structure is made of 18mm thick Pre-laminated particle board Make: Featherlite. VS 7575 Size 750W x 450D x 750HT

STORAGE: MODEL VERSALINE STORAGE UNIT Specifications: The structure is made of 18mm thick Pre-laminated particle board Make: Featherlite. VS 9075 Size 900W x 450D x 750HT

STORAGE: MODEL VERSALINE STORAGE UNIT Specifications: The structure is made of 18mm thick Pre-laminated particle board Make: Featherlite. VS 90120 Size 900W x 450D x 1200HT

GM'S CHAIR MODEL: LIBERATE HB - Make: Featherlite

GM'S CHAIR MODEL: ASTRO VA Make: Featherlite

FUNCTIONAL MANAGER'S and CONFERENCE HEAD CHAIR MODEL: OPUS HB Make: Featherlite

ADCI/AM/SI CHAIR, MODEL: ASTRO MB Make: Featherlite

EO/HEAD ASSISTANT/ACCOUNT'S OFFICER CHAIR. MODEL: SMART MB FIXED ARM Make: Featherlite

JUNIOR ASSISTANT CHAIR. MODEL: CONTACT PROJECT VA Make: Featherlite

VISITOR`S CHAIR. MODEL: SMART VA Make: Featherlite

SOFA , MODEL: S900 1S (CONVERSE) SINGLE SEATER SOFA, Size: 790H x 880W X 780D Make: Featherlite

CENTER TABLE, MODEL: 610-FL CENTER TABLE Rectangular Table no. each Glass top Chrome frame Size: 1200 x 600 mm Make: Featherlite

Fees to local authority for building permission

FOUNDATIONSTONE_LAYING_CEREMONY: Providing Dais with steel structure frame and 38 mm thick timber plank and removing the same after completion of the programme including carriage etc. (approx. quantity = 240 sqft), providing Penndel of Bhaluka bamboo post & Jati bamboo frame with water proof roof, ceiling cloth decoration and removing the same after completion of the programme including carriage etc. (approx. quantity = 1000 sqft), providing plaque with necessary write ups over granite slab as required (approx. quantity = 6 sqft), providing flower decoration and balloon at Dais, Penndel & building as required, providing Seminar chair for Dais and removing the same after completion of the programme (approx. quantity 10 nos.), providing VIP Chair with cover and removing the same after completion of the programme (approx. quantity 15 nos.), providing plastic chair with cover and removing the same after completion of the programme 250 nos.), providing Lamp Stand with necessary items like Ribbon, Scissor, M. Oil, Salita, etc. for opening ceremony and removing the same after completion of the programme, Supplying of fresh Flower Buckeye (approx. quantity 10 nos.), supplying of best quality fulam Gamossa (approx. quantity 15 nos.), providing Sound System with operator including carriage to the programme site and returned back after completion of the programme, providing Welcome Gate with Banner (Flex) including decoration and removing the same after completion of the programme, providing Back Drop Banner (Flex) including printing and fixing complete, drinking water arrangement- (Water Bottle of 500 ml- approx. 250 nos.,, Water Bottle of 20 lit.- approx. 3 nos., Disposable Glass- approx. 250 nos.), providing Carpet for Dais and VIP Area including carriage to the programme site and returned back after completion of the programme- (approx. quantity = 500 sqft.), providing Podium for Dais including carriage to the programme site and returned back after completion of the programme, providing Refreshment item (Packet Lunch) for audience (each packet contains- Gulab Jamun-1, Veg Cutlet-1, Kasuri-1, Boil Cake-1 & tea)- approx. quantity 250 nos., providing Refreshment item for VIP (High Tea) (Boil Cake-1, Veg. Cutlet-1, Kaju Barfi-1, Fry kaju, Biscuits)- approx. quantity 25 nos., providing Flower Tub including carriage and returned back after completion of the programme, Big size- approx. quantity 10 nos., Small size- approx. quantity 20 nos., providing Dust Bin including carriage and returned back after completion of the programme approx. quantity 20 nos. all complete as required and as per direction of the deptt. to make the programme success.

INAUGURATION_CEREMONY: Providing Dais with steel structure frame and 38 mm thick timber plank and removing the same after completion of the programme including carriage etc. (approx. quantity = 240 sqft), providing Penndel of Bhaluka bamboo post & Jati bamboo frame with water proof roof, ceiling cloth decoration and removing the same after completion of the programme including carriage etc. (approx. quantity = 1000 sqft), providing plaque with necessary write ups over granite slab as required (approx. quantity = 6 sqft), providing flower decoration and balloon at Dais, Penndel & building as required, providing Seminar chair for Dais and removing the same after completion of the programme (approx. quantity 10 nos.), providing VIP Chair with cover and removing the same after completion of the programme (approx. quantity 15 nos.), providing plastic chair with cover and removing the same after completion of the programme 250 nos.), providing Lamp Stand with necessary items like Ribbon, Scissor, M. Oil, Salita, etc. for opening ceremony and removing the same after completion of the programme, Supplying of fresh Flower Buckeye (approx. quantity 10 nos.), supplying of best quality fulam Gamossa (approx. quantity 15 nos.), providing Sound System with operator including carriage to the programme site and returned back after completion of the programme, providing Welcome Gate with Banner (Flex) including decoration and removing the same after completion of the programme, providing Back Drop Banner (Flex) including printing and fixing complete, drinking water arrangement- (Water Bottle of 500 ml- approx. 250 nos.,, Water Bottle of 20 lit.- approx. 3 nos., Disposable Glass- approx. 250 nos.), providing Carpet for Dais and VIP Area including carriage to the programme site and returned back after completion of the programme- (approx. quantity = 500 sqft.), providing Podium for Dais including carriage to the programme site and returned back after completion of the programme, providing Refreshment item (Packet Lunch) for audience (each packet contains- Gulab Jamun-1, Veg Cutlet-1, Kasuri-1, Boil Cake-1 & tea)- approx. quantity 250 nos., providing Refreshment item for VIP (High Tea) (Boil Cake-1, Veg. Cutlet-1, Kaju Barfi-1, Fry kaju, Biscuits)- approx. quantity 25 nos., providing Flower Tub including carriage and returned back after completion of the programme, Big size- approx. quantity 10 nos., Small size- approx. quantity 20 nos., providing Dust Bin including carriage and returned back after completion of the programme approx. quantity 20 nos. all complete as required and as per direction of the deptt. to make the programme success.

Sri Bhaskar Ranjan Patgiri

Dhruba Jyoti Saikia