Balance Work for Construction of 28 No. Estates Flats (Single Block) G plus 6 by way of Civil, Plumbing and Sanitary and other Allied works at Sarwal Jammu.

Amount

Earth work in excavation by manual means in foundation trenches, drains, pipes and cables etc. (not exceeding 1.5mtr in width or 10 sqm on plan including dressing of sides and ramming of bottoms, lift upto 1.5mtr including getting out excavated soil and disposal of surplus soil as directed, within a lead of 50 mtr. All kinds of soils

Extra for every additional lift of 1.5 mtr or part thereof in excavation:- All kinds of soils

exceeding 1.5 m in depth but not exceeding 3.0 m

exceeding 3.0 m in depth but not exceeding 4.5 m

exceeding 4.5 m in depth but not exceeding 6.0 m

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level complete:- (Including cost / Carriage of material by Mechanical transport)

1:4:8 (1 cement: 4 coarse sand :8 graded stone aggregate 20 mm nominal size) :- CRUSHED

1:3:6 (1 cement: 3 coarse sand :6 graded stone aggregate 20 mm nominal size) :- CRUSHED

1:2:4 (1 cement: 2 coarse sand :4 graded stone aggregate 20 mm nominal size):- CRUSHED

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering; at all floor levels complete All work above plinth level upto floor five level:- (Including cost / Carriage of material by Mechanical transport)

1:4:8 (1 cement: 4 coarse sand :8 graded brick aggregate 40 mm nominal size):- CRUSHED

1:3:6 (1 cement: 3 coarse sand :6 graded stone aggregate 20 mm nominal size):- CRUSHED

1:2:4 (1 cement: 2 coarse sand :4 graded stone aggregate 20 mm nominal size):- CRUSHED

Extra for plain cement concrete work in superstructure above floor five level for each four floors or part thereof.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering. shuttering, finishing and reinforcement:- 1:1.5:3 (1 cement: 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size) complete :- CRUSHED (Including cost / Carriage of material by Mechanical transport)

All works upto plinth level

All works above plinth level upto floor V level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in- charge. Note: - Cement in this item is @ 410 kg/ cum complete incl. cost / carriage of material by Mech. Transport. Excess or less cement used as per design mix is content considered payable or recoverable separately.

All works upto plinth level

All works above plinth level upto floor V level

Extra for R.C.C./B.M.C./R.M.C. work above floor V level for each four floors or part thereof.

Centring and shuttering including strutting, propping etc. and removal of form work for:-

Foundations: footings, bases of columns etc. for mass concrete.

Columns, Pillars, Piers, Abutments, Posts and Struts

Walls any thickness including attached pilasters, buttresses and plinth

Lintels, beams, plinth beams, girders,bressumers and centilevers.

Suspended floors, roofs, landings, balconies and access platform.

Edges of slabs and breaks in floors and walls. Under 20 cm wide

Stairs, (excluding landings) except spiral staircases.

Extra for additional height in centring, shuttering where ever required with adequate bracing, propping etc including cost of de-shuttering and decentring at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured):- Suspended floors. roofs, landing, beams and balconies (Plan area to be measured):- For Pergola Beams

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-mechanically treated bars of grade Fe-500D or more for all levells complete (Including cost / Carriage of material by Mechanical transport)

Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth including curing in:- Cement mortar 1:6 ( 1 cement : 6 coarse sand); (Including cost / Carriage of material by Mechanical transport)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Extra for brick work/tile brick/AAC block masonry in superstructure above floor V level for each four floors or part thereof by mechanical means:

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand); (Including cost / Carriage of material by Mechanical transport)

Extra for half Brick masonry in superstructure above plinth level upto floor V level.

Extra for half Brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.

Extra for providing and placing in position 2 Nos. 8 mm dia. M.S. bars at every third course of half brick masonry.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.

Providing and fixing of M.S. cover with frame both I.S.I. marked heavy duty for Manholes in Sump/ Septic tanks 560x560 mm size ( the weight of the cover to be not less than 108 Kg); also includes priming coat over them all complete

6mm cement plaster to ceiling of mix 1 : 3 (1 cement: 3 fine sand) all complete including making of groves and scaffolding etc., all floor levels complete building (Including cost / Carriage of material by Mechanical transport)

15mm Cement plaster on the rough side of single or half brick walls of mix: 1 : 6 ( 1 cement : 6 fine sand) on interior walls ,all complete including making of groves and scaffolding, etc. at all floor levels complete (Including cost / Carriage of material by Mechanical transport)

20mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) ,in two coats on exterior walls, all complete including making of groves and scaffolding etc., all floor levels complete (Including cost / Carriage of material by Mechanical transport)

Providing and making for plaster drip course to R.C.C. projections(Chajjas) ,all floor levels complete (Including cost / Carriage of material by Mechanical transport)

Providing and laying of vitrified floor tiles (double charged) in different sizes (thickness to be specified by the manufacturer) (Anti-skid) with water absorption less than 0.08% and conforming to lS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete SOMANY/ KAJARIA or equivalent only make; at all floor levels complete:- size of tile 60cmx60cm (Including cost / Carriage of material by Mechanical transport)

Providing and laying of Tile work in skirting, risers of steps and dado (upto 2m height) over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with pigment of matching shade complete of SOMANY/ KAJARIA or equivalent only make, all floor levels complete building:- Marble tiles(polished Raj Nagar) / Vitrified tiles - 8mm thick (Including cost / Carriage of material by Mechanical transport)

Providing and fixing Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) (Anti-skid) of 1st quality conforming to IS: 13755 of SOMANY/ KAJARIA or equivalent only make in colour such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1: 4 ( 1 cement : 4coarse sand) including pointing the joints with white cement and matching pigment etc., complete at all floor levels complete:- (Including cost / Carriage of material by Mechanical transport)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS :·13753 of minimum thickness 5 mm of approved make like SOMANY/KAJARIA only make in all colour, shades except begundy,bottle green, black of any size as approved by Eningeerin-Charge in skirting, risers of steps and dados over 12mm thick bed of Cement Mortar 1:3 ( 1 cement: 3 coarsesand) and jointing wtih grey cement slurry@ 3.3 kg persqm including pointing in white cement mixed withpigment of matching shade complete, at all floor levels complete:- (Including cost / Carriage of material by Mechanical transport)

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels complete. Granite of any colour or shade:-Polished Granite stone slab jet Black, Cherry Red, Eliten Brown, Cat Eye or equivalent. (Area of slab over 0.5 sqm) 18 mm thick (Including cost / Carriage of material by Mechanical transport)

Extra for providing edge moulding to 18 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge :-Granite work (Including cost / Carriage of material by Mechanical transport)

Extra for providing opening of required size and shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble / stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete. (Including cost / Carriage of material by Mechanical transport)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to openings / wooden frames with rawl plugs screws etc.

Providing and fixing of glass panes with existing wooden fillets: Glass panes weighing 13.75 kg / sqm ( 5.5 mm thick) of make Saint Gobin or Modi float or equivalent ISI marked; all complete

Making plinth protection 50 mm thick of cement concrete 1:3:6( 1 cement : 3 coarse sand : 6 graded stone aggreagate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. (a) Crushed (Including cost / Carriage of material by Mechanical transport)

Brick edging 7 cm wide 11.4 cm deep to plinth protection with bricks of class designation 75 including grouting with cement mortar 1:4 (1 cement: 4 fine sand) (Including cost / Carriage of material by Mechanical transport)

Providing and fixing glass strips in joints of terrazo or cement concrete floor. 40 mm wide and 6 mm thick

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works all complete.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc.including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete,i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge complete incl. carriage, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets and matching fillets as approved by Engineer incharge at site, fixed with C. P. brass screws and wooden plugs, etc. wherever necessary complete : 25 mm dia.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design:In 75x75 mm deep chase (Including cost / Carriage of material by Mechanical transport)

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacture of Birla/JK white only over the plastered wall surface to prepare the surface even and smooth complete.( Inner walls and ceilings) at all floor levels complete including scafolding:- (Including cost / Carriage of material by Mechanical transport)

Distempering with oil bound washable distemper of approved brand and manufacture Asian / Nerolac / Berger / Dulux paints only to give an even shade New work (two or more coats) over and including priming coat with cement primer; at all floor levels complete:- (Including cost / Carriage of material by Mechanical transport) with scafolding complete.

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28litre/10sqm over and including base coat of waterproofing cement paint applied@ 2.20kg/10sqm); and also providing weather shield protection coat over the textured surfaces, all complete of approved brand and manufacture Asian/Nerolac/Berger/Dulux paints only all complete including scaffolding etc.; at all floor levels complete:- (Including cost / Carriage of material by Mechanical transport)

Providing and Applying priming coat: with ready mixed pink or grey primer of approved brand and manufacture Asian/Nerolac/Berger/Dulux paints only on wood work (hard and soft wood) one or more coats (Including cost / Carriage of material by Mechanical transport)

Painting with ready mixed synthetic enamel paint of approved brand and manufacture Asian / Nerolac / Berger / Dulux paints only in all shades to give an even shade New steel/wood work complete at all levels (two or more coats) (Including cost / Carriage of material by Mechanical transport)

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying complete incl. all carriages involved: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement -,. compound@ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (Including cost / Carriage of material by Mechanical transport) (c) third layer of 1.5 mm thickness consisting of slurry ofcement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg./sqm. and coarse sand @1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured.

Providing and laying integral cement based water proofing treatment including prepration of surfaces as required for treatment of roofs, balconies, terracies etc consisting of following operations(Including cost / Carriage of material by Mechanical transport) a) applying a slurry coat of neat cement using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC Slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/ Brick Bats 25mm to 115mm size with 50% of Cement mortar 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 Cement: 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300mm height including rounding of Junctions of walls and slabs) c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. d) finishing the surface with 20mm thick jointless cement mortar of mix 1:4(1 cement: 4 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved byEngineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finially finishing the surface with trowel with neat cement slurrv and making pattern of 300x300mm/sq 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurra as 65 mm.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete (Including cost / Carriage of material by Mechanical transport)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class teak wood

Providing and fixing 35 mm thick glazed shutters for Windows, Doors, ventilators and clerestory windows using 10 kg/sqm (4mm thick) float glass panes with lSI marked Stainless steel Butt hinges (heavy weight) of required size with necessary screws (float glass should be of make Saint Gobain or Modi float or equivalent) :- Second Class Deodar Wood (Including cost / Carriage of material by Mechanical transport)

Providing and fixing 35 mm thick wire gauze shutters using galvanised M.S. wire gauze of average width for aperture 1.4 mm in both direction with wire of dia. 0.63 mm for doors, windows, ventilators and clerestory windows with lSI marked Stainless Steel Butt hinges (heavy weight) of required size with necessary screws :- Second Class Deodar Wood (Including cost / Carriage of material by Mechanical transport)

Providing and fixing & fabrication of 35 mm thick Laminated Flush Door Shutters made up of 32 mm thick solid core flush door (Gurjan core) having 1.5 mm thick Laminate/Sunmica Matt finish on both faces & 35x6 mm thick Teak wood lipping/margin on alround of Flush door and also including fixing of door shutters with I.S.I. marked stainless steel butt hinges 100x60x2.5 mm heavy weight & necessary S.S. screws; all complete:- (32mm thick solid core flush door should of make Sonear/Archid/Green/Century or equivalent only & 1.5 mm thick Sunmica Matt finish should of make Merino/Green/Archid/Century or equivalent only & Flush door should be water proof BWP I.S. 710 grade, borer free, anti-termite, fire retardent etc.) fabrication be done at site (Including cost / Carriage of material by Mechanical transport)

Providing and fixing & fabrication of 40 mm thick Teak Veneered Flush Door Shutters made up of 32 mm thick solid core flush door (Gurjan core) having 4 mm thick Teak veneer on both faces & 40x6 mm thick Teak wood lipping/margin on alround of Flush door and also including fixing of door shutters with I.S.I. marked stainless steel butt hinges 100x60x2.5 mm heavy weight & necessary S.S. screws; all complete:- (32mm thick solid core flush door should of make Sonear/Archid/Green/Century or equivalent only & 4mm thick Teak veneer should of make Green/Archid/Century or equivalent only & Flush door should be water proof BWP I.S. 710 grade, borer free & anti-termite, fire retardent etc.) fabrication be done at site (Including cost / Carriage of material by Mechanical transport)

Providing, Manufacturing, Fabricating and Fixing of Wooden Ward Robe/Cupboard made of Box shelves and Drawers of 18 mm thick Ply wood; fitted with 6.0 mm thick Ply wood at back; shutters of 19 mm thick Ply board at front; lipped with 6mm thick Teak wood Lipping/Margin alround; finished with 0.8 mm thick Sunmica on inside and 1.0 mm thick Sunmica at front outside; fitted with I.S.I. marked Hardware accessories and fixtures:- 3"x1" S.S. hinges (heavy weight), 8" long Handles, Hanger Rods with side support brackets, Drawer channels 20" long of Hettich make, Conceal handles, Magnetic catchers, 6" long Tower-bolts, Cupboard & Drawer Locks, etc. all complete ( Plywood & Ply Board should be of make Green/ Century/ Archid/ Sonear/ Virgo only and should be water proof BWP I.S. 710 grade, anti-termite, Borer free, Fire retardent etc.; & Sunmica should be of make Merino/ Green/ Century/ Sonear/ Virgo only; and all the Hardware accessories & fixtures should be of approved brand & I.S.I. marked only) fabrication be done at site (Including cost / Carriage of material by Mechanical transport)

Providing, fabricating, manufacturing and fixing of Wooden Kitchen Cabinet mounted on wall made of Box shelves of 18 mm thick Ply wood; fitted with 6.0 mm thick Ply wood at back; shutters of 19 mm thick Ply board at front; lipped with 6mm thick Teak wood Lipping/Margin alround; finished with 0.8 mm thick Sunmica on inside and 1.0 mm thick Sunmica on outside; fitted with I.S.I. marked Hardware accessories and fixtures:- 3"x1" S.S. hinges (heavy weight), 4" long Handles, Magnetic catchers etc. all complete ( Plywood & Ply Board should be of make Green/ Century/ Archid/ Sonear/ Virgo only and should be water proof BWP I.S. 710 grade, anti-termite, Borer free, Fire retardent etc.; & Sunmica should be of make Merino/ Green/ Century/ Sonear/ Virgo only; and all the Hardware accessories & fixtures should be of approved brand & I.S.I. marked only) fabrication be done at site (Including cost / Carriage of material by Mechanical transport)

Providing and applying Melamine polishing Matt finish on Teak Veneered Flush Door Shutters of approved brand & manufacture Asian/ Nerolac/ Berger/ Dulux paints only (one or more coats); all complete

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene .. gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in Charge complete for all levels (glazing, panelling and dash fasteners to be paid for separately.) (Including cost / Carriage of material by Mechanical transport) Polyester powder coated aluminium (minimum thickness of polyester powder coated 50 microns) 10 Gauge including carriages complete.

For fixed portion/ frames

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber I neoprene gasket required complete for all levels (Fittings shall be paid for separately.)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-l type-11) in panelling fixed in aluminium doors, windows shutters and partition frames with C. P. brass I stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge:- Pre-laminated particle board with decorative lamination on both sides (Including cost / Carriage of material by Mechanical transport)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber I neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.) With float glass panes of 5.50 mm thickness (weight not less than 13. 50 kg / sqm) (Including cost / Carriage of material by Mechanical transport)

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/stainless steel screws@ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (only weight of grill to be measured for payment) (Including cost / Carriage of material by Mechanical transport)

Providing and fixing aluminium sliding door bolts lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

300 mm long

200 mm long

125 mm long

Providing and fixing aluminium pull bolt lock anodised lSI marked (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws bolt nuts and washers etc. complete .

Providing and fixing aluminium hanging floor door stopper lSI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Twin rubber stopper

Providing and fixing aluminium Eye Hook Latch lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or eyed to required colour or shade with necessary screws etc. complete :

Providing and fixing of Rubber Door back stopper Lever type door mounted with necessary screws/nuts etc. complete: 75 mm long

Providing and fixing aluminum round shape handle of outer dia 100mm with SS screws etc. Complete as per direction of Engineer-in-charge Polyester powder coated minimum thickness 50 microns aluminium

Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS: 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete :

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding holdfasts in cement concrete blocks of size 15x10x10cm with cement concrete 1:3:6 (1 cement :3 coarse sand: 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground within 50 meters lead:

Door chowkhats

Window chowkhats

Clerestory window chowkhats

Fixing chowkhat in existing opening in brick/RCC wall with dash fasteners/chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhats and 2 nos. on each vertical member of window chowkhats), including cost of dash fasteners/chemical fasteners.

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.

Cleaning of under ground sump, Over Head R.C.C. Tank (independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:- (i)Tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits. (ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. (iii) Chlorination of RCC internal surface by liquid chlorine. (iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge.

Rebaring of Tor-steel bars of required dia. by way of drilling holes of required dia. upto the depth of (10-15) times of dia. of hole with hammer drilling machine or core cutting machine and then cleaning of hole by way of removal of dirt, dust and loose particles and then filling of chemical of HILTI make Hy-150/ Hy- 200/ Re-500 as recommended upto 2/3 depth of hole and then fixing of bars by rotating in the hole upto the drilled depth:-

8mm dia. of bars

10mm dia. of bars

12mm dia. of bars

16mm dia. of bars

20mm dia. of bars

25mm dia. of bars

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge incl. cost / carriage of material by Mechanical Transport.

Lettering with black japan paint of approved brand and manufacturing complete

Supplying chemical emulsion in sealed containers including delivery as specified: chlorophyriphos/ Lindane emulsifiable concentrate of 20% complete

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termite treatment complete incl. all carriages (excluding the cost of chemical emulsion) :

Along external walls where the apron is not provided using chemical emulsion@ 7.5 Ltr/sqm of the vertical surface of the substructure to a depth of 300 mm including excavation of channe! along the wail & rodding etc. with' chlorophyriphos/ Lindane E. C 20% with 1% concentration.

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ linear mtr. including drilling and plugging holes etc. With chlorophyriphos/Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @ 1 ltr/hole, 300mm apart including drilling 12mm diametre holes and plugging with cement mortar 1: 2 (1 cement: 2 coarse sand) to match the existing floor. with chlorophyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of existing masonry using chemical emulsion @ 11tr/ hole at 300mm interval including drilling holes at 45° and plugging them with cement mortar 1: 2 (1 Cement : 2coarse sand) to the full depth of hole. with chlorophyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of points of contact of wood work by chemical emulsion of chlorophyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 ltr/ hole by drilling 6mm dia holes at downward angle of 45° at 150mm centre· to centre and sealing the same

DISMANTLING WORK:-

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 metres lead: 1:4:8 or leaner mix

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead : In Cement Mortar

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m. (stacks of cleaned bricks shall be measured) : From brick work in cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead: Of area of 3 sq. metres and below

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 metres lead of: G.S. Sheet

PLUMBING & SANITARY

Providing and fixing white vitreous china pedestal type water closet (European type W.C . .pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requied W.C. pan with lSI marked white solid plastic seat and lid of make Hindware/Cera/Jaquar only:- (incl. All Carriages)

Providing and fixing wash basin with C. I./M.S. brackets,15mm C.P. centre hole basin mixture, 32 mm C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps of make Hindware/Cera/Jaquar only:- (incl. All Carriages)

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings of make Hindware/Cera/Jaquar only:- (incl. With Carriages)

Providing and fixing Salem Stainless Steel A lSI 304 (18/8) kitchen sink including waste coupling as per I.S. 13983 with C.l. brackets and stainless steel plug 40 mm including painting of fitting sand brackets, cutting and making good the walls wherever required of make Kaff/Neelkanth/Hindware or equivalent all complete :-510x1040mm bowl depth 250mm (incl. With Carriages)

Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fitting complete. Flexible pipe 40 mm dia (With Carriages)

Providing and fixing 100 mm CP grating (hole or without hole) for gully, floor or Nahani trap.ISI marked All complete of make hindware/Cera/Jaquar only:- (With all Carriages)

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete ISI marked of make Saint Gobin or Modi float or equivalnet brand as approved by Engineer incharge at site:- (With all Carriages)

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C. P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete of make hindware/Cera/Jaquar only:-

Providing and fixing unplasticised - Rigid PVC PIPES conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap of thermal expansion;with necessary stays / clamps with fasteners having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport)

50 mm dia

75 mm dia

110 mm dia

160 mm dia

200 mm dia

250 mm dia

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport)

PVC PLAIN BEND (of required degree):-

50 mm dia.

75 mm dia.

110 mm dia

160 mm dia.

200 mm dia.

PVC DOOR BEND( of required degree):-

50 mm dia.

75 mm dia.

110 mm dia

160 mm dia.

200 mm dia.

PVC PLAIN TEE:-

50 mm dia.

75 mm dia.

110 mm dia

160 mm dia.

200 mm dia.

PVC DOOR TEE:-

50 mm dia.

75 mm dia.

110 mm dia

160 mm dia.

200 mm dia.

PVC REDUCER PLAIN TEE:-

110 mm x 75 mm

160 mm x 110 mm

200 mm x 160 mm

PVC REDUCER DOOR TEE:-

110 mm x 75 mm

160 mm x 110 mm

200 mm x 160 mm

PVC OFFSETS:-

50 mm PVC off sets

75 mm PVC off sets

110 mm PVC off sets

160 mm PVC off sets

200 mm PVC off sets

PVC COUPLER/COLLAR:-

50 mm dia

75mm dia

110mm dia

160 mm dia

200 mm dia

PVC VENT COWL:-

75mm dia

110mm dia

160 mm dia

PVC FLOOR/NAHANI TRAP:-

110 mm x 75 mm

110 mm x 100 mm

PVC P/Q/S TRAP:-

100 mm dia.

Providing and fixing square- mouth S.W. gully trap grade 'A' complete with C. I. grating brick masonry chamber with bricks of class designation 75 in cement mortar 1:5 ( 1 cement : 5 fine sand) and water tight C. I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design.:- 180 x 150 mm size P type With F.P.S. bricks (Including cost / Carriage of material by Mechanical transport)

Providing and fixing Soap dish (C.P. brass) with brackets ,nuts & screws complete etc. of make hindware/Cera/Jaquar only:- (With all Carriages)

Providing and fixing towel ring (C.P. brass) with brackets ,nuts & screws complete etc. of make hindware/Cera/Jaquar only:- (With all Carriages)

Providing and fixing towel rail 600mm long (C.P. brass) with brackets ,nuts & screws complete etc. of make hindware/Cera/Jaquar only:- (With all Carriages)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931 of make hindware/Cera/Jaquar only:-. (a)15 mm nominal bore (With all Carriages)

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms of make hindware/Cera/Jaquar only: (With all Carriages) a) 15 mm nominal bore

Providing and fixing C.P.Brass stop cock (concealed) of standard design and of approved make conforming to IS : 8931 of make hindware/Cera/Jaquar only: (With all Carriages) a) 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin/wall mixer and geysers points of approved make conforming to IS : 8931 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge (With all Carriages)

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore (With all Carriages)

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge all complete of make hindware/Cera/Jaquar only:-. (With all Carriages)

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.

Providing and fixing C.P. Brass Central Hole BASIN MIXER without Popup Waste System with 450mm Long Braided Hoses with necessary screws, brackets, nuts or bolts etc; all complete of make hindware/Cera/Jaguar only:- (With all Carriages) (a) 15 mm nominal bore

Providing and fixing C.P. Brass SINK MIXER with Swinging Spout (Wall Mounted Model) With Connecting Legs & Wall Flanges with necessary screws, brackets, nuts or bolts etc; all complete of make hindware/Cera/Jaguar only:- (With all Carriages) (a) 15 mm nominal bore

Providing and fixing of C.P. Brass WALL MIXER with provision for Overhead Shower with 115mm Long Bend Pipe on Upper Side, Connecting Legs & Wall Flanges with necessary screws, brackets, nuts or bolts etc; all complete of make hindware/Cera/Jaguar only:- (Incl. all Carriages) (a) 15 mm nominal bore

Providing and fixing of C.P. Brass OVERHEAD SHOWER 100mm dia. Round Shape Single Flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System with necessary screws, brackets, nuts or bolts etc; all complete of make hindware/Cera/Jaguar only:- (Incl. all Carriages) (a) 15 mm nominal bore

Providing and fixing of C.P. Brass SHOWER ARM Casted 190mm Long Light Body Round Shape For Wall Mounted Showers with Flange with necessary screws, brackets, nuts or bolts etc; all complete of make hindware/Cera/Jaguar only:- (Incl. all Carriages) (a) 15 mm nominal bore

Providing and fixing G.l. pipes complete with G.l. fittings and clamps, including cutting and making good the walls etc.(internal work) of make Jindal/Surya Prakash of medium class or as approved by site incharge (INTERNAL WORK-Exposed on wall) all complete including testing of pipes and fittings and joints for leakage with pressure pump etc. (Incl. all carriages)

15 mm dia. nominal bore (medium)

20 mm dia. nominal bore (medium)

25 mm dia. nominal bore (medium)

32 mm dia. nominal bore (medium)

40 mm dia. nominal bore (medium)

50 mm dia. nominal bore (medium)

Providing and fixing G.l. pipes complete with G.l. fittings and clamps, Concealed pipe including painting with anti-corrosive bitumastic paint(two coats) over a ready mixed priming coat , cutting chases and making good the wall , all complete including testing of pipes and fittings and joints for leakage with pressure pump etc.of make Jindal/Surya Prakash of medium class or as approved by site incharge (Incl. all carriages)

15 mm dia. nominal bore (medium)

20 mm dia. nominal bore (medium)

Providing and fixing G.l. pipes complete with G.l. fittings including trenching and refilling etc. (EXTERNAL WORK) of make Jindal/Surya Prakash of medium class or as approved by site incharge all complete including testing of pipes and fittings and joints for leakage with pressure pump etc. (Incl. all carriages)

25 mm dia. nominal bore

32 mm dia. nominal bore

40 mm dia. nominal bore

50 mm dia. nominal bore

Making connection of G.l. distribution branch with G.l. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete all complete including testing of pipes and fittings and joints for leakage with pressure pump etc.of make UNIK or NEW or equivalent as approved by site incharge (Incl. all carriages)

25 to 40 mm nominal bore

50 to 80 mm nominal bore

Providing and fixing G.l. Union in G.l. pipe including cutting and threading the pipe and making long screws etc. complete (new work) all complete including testing of pipes and fittings and joints for leakage with pressure pump etc.of make UNIK or NEW or equivalent as approved by site incharge (Incl. all carriages)

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and filling sand of coarser grade alround the G. I. pipes in external work. (Including cost / Carriage of material by Mechanical transport)

25 mm dia. nominal bore

32 mm dia. nominal bore

40 mm dia. nominal bore

50 mm dia. nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license] (incl. cost / carriage of material upto roof top).

Providing and fixing G.I.TANK NIPPLE of suitable dia. of make UNIK or NEW or equivalent ISI marked as approved by engineer incharge at site all complete including testing of fittings and joints for leakage etc.:- (incl. all carriages)

25 mm dia. nominal bore

32 mm dia. nominal bore

40 mm dia. nominal bore

50 mm dia. nominal bore

Providing & fixing BRASS BALL VALVE of approved quality conforming to IS : 8931 of make UNIK or DRP or as approved by site incharge (incl. all carriages)

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and fixing BRASS FLOAT BALL VALVE; High or low pressure with plastic floats:- of approved quality conforming to IS : 8931 of make UNIK or DRP or approved by engineer incharge at site (incl. all carriages)

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Providing and fixing Gun metal gate valve with C.l. wheel of approved quality (screwed end) conforming to IS : 8931 of make UNIK or DRP or as approved by site incharge (incl. all carriages)

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and fixing Gun metal non-return valve of approved quality (screwed end) conforming to IS : 8931 of make UNIK or DRP or as approved by site incharge (incl. all carriages)

25 mm nominal bore

Horizontal

Vertical

32 mm nominal bore

Horizontal

Vertical

40 mm nominal bore

Horizontal

Vertical

50 mm nominal bore

Horizontal

Vertical

Providing and fixing Brass Foot valve with strainer/filter of approved quality (screwed end) conforming to IS : 8931 of make UNIK or DRP or as approved by site incharge (incl. all carriages)

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and fixing of stainless steel Rainwater Khurra JALI to be placed at roof and mumty levels of make CHILLY or CAMRY or equivalent all complete:- square or circular in shape of dia/size:- (incl. all carriages)

Providing & Installation of 3 H.P. three phase water pump of make Crompton with all fittings, connecting inlet & outlet, fixtures, electrical connection and starter all complete:- (incl. all carriages)

Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay F.P.S. (non modular) bricks (Including cost / Carriage of material by Mechanical transport)

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 gradedstone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. (Including cost / Carriage of material by Mechanical transport)

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) R.C.C. top slab with 1 :2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finsihed with a floating coat of neat cement complete as per standard design (Including cost / Carriage of material by Mechanical transport)

Inside size 90x80 cm and 45 cm deep including C.l. cover with frame (light duty) 455x610 mm. internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) With F.P.S. bricks with class designation 75 & with Crushed stone aggregate

Inside size 90x80 cm and 60 cm deep including C.l. cover with frame (light duty) 455x61 0 mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) 21.7.2.1 With F.P.S. bricks with class designation 75 & with (a) Crushed stone aggregate

Extra for depth for brick masonry manholes:- Size 90x80cm With F.P.S. bricks with class designation 75 (Including cost / Carriage of material by Mechanical transport)

Constructing brick masonry open surface drain with bricks of class designation 75 in cement mortar 1:4 ( 1 cement : 4 fine sand) including earth excavation, 10 cm thick bed concrete 1:5:10 ( 1 cer.1ent: 5 fine sand: :10 graded stone aggregate 40 mm nominal size) and 25mm thick cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) for filling haunches including 12 mm cement plaster 1:4 ( 1 cement : 4 coarse sand) with a floating coat of neat cement inside the drain, its top and exposed side including disposal of surplus earth complete as per standard design: 25 cm drain 30 cm average depth:- With F. P. S. bricks with (a) Crushed stone aggregate (Including cost / Carriage of material by Mechanical transport)

Making soak pit 2.5 m diameter 3.0 metre deep with 45x45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design by way of earth excavation by mechanical means; laying of 100 mm thick P.C.C. bed in 1:4:8 mix ratio & R.C.C. Slab on top in 1:1.5:3 mix ratio; providing and fixing of Manhole with MS frame and cover having passing of 50 mm dia. Vent air pipe through it for foul gases; brick masonry in 1:6 cement mortar mix with providing of pores; and filling of brick bat aggregates around the dry brick honey comb shaft; P/F of pvc bend/tee at the S.W. Drain pipe; all complete etc:- With F.P.S. bricks and Crushed (Including cost / Carriage of material by Mechanical transport)

LANDSCAPING:-

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing off by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure)

Supplying and stacking of good earth at site including royalty and carriage complete (earth measured in stacks will be reduced by 20% for payment)

Supplying & stacking sludge-:> at site including royalty and carriage complete ( sludge measured in stakes will be reducd by 8% for payment.

Supplying and stacking at site dump manure from badi or other approved source including carriage upto 1 km (manure measured in stacks will be reduced by 8% for payment) Screened through sieve of I.S. designation 4.75 mm

Rough dressing of the trenched ground including breaking clods

Uprooting weeds from the trenched area after 1 0 to 15 days of its flooding with water including disposal of uprooted vegetation

Fine dressing of the ground

Providing, Supplying and plantation of flowers, plants of different types all complete:-

Disposal of surplus excavated Earth work / mulba material by mechanical transport beyond 50 mtr and within average distance of 10 Kms

Cleaning of entire floors / premises of building by way of cleaning of all floors / windows etc by way of engagement of labour before handing over to Project Authority

Providing of door pad lock of superior quality alongwith two set of key

SHARAT PURI CONTRACTORS