REPAIR/MAINT TO LT PANEL BOARD, FPB, JUNCTION BOXES, MCCB, ACB AND REPAIR/MAINT TO STRRET LIGHTS/SECURITY LIGHTS, FLOOD LIGHTS, GARDEN LIGHTS, BRACKETS, POLE PAINTING, LT UG CABLE AND CONNECTED WORK SERVICES AT KIARI, CHUMATHANG AND NYOMA UNDER GE 86

Amount

S&F in replacement of LT panel box, by means of nut bolts washer, and opening of existing LT cables properly stacking, and supply, installation, testing and commissioning of CPRI approved, factory made, LT panel board cubical, Outdoor type, floor mounted double door, 3 phase 4 wire, 50 cycles, 415 Volts. The panel board shall be made of 3.15 thick CRCA sheet for load bearing members and 16 SWG (1.6 mm thick) for doors covers and internal partitions and shall be powder coated both side. Base frame of the panel shall be made of ICMC channel of size 50 x50 x 6mm, duly grouted on platform made of brick work in CM (1:2:4), 15mm thick plastering in CM (1:6) having minimum height of 450mm. The panel shall be provided with separate compartments for each switch gears with hinged door including interlocking with switch gears. The panel board shall be suitable for AC, 415 Volts, 50 Hz, 3 phase, 4 wire supply complete with epoxy insulated 800 Amps rated high conductivity aluminium bus bars, supported with DMC / SMC barriers and coluor coded, prewired with copper cable, the degree of protection is IP-54. the panel shall be complete with instrumentation such as LED phase indicating lamps and CT's, including extended aluminium strip of rating of Incomer (400Amps), and outgoing as per rating of MCCB’s, including aluminium lugs to connect the cable dismantled before etc. and comprising of the following:-

(a) MCCB 400 Amps, 4 pole with breaking capacity 36KA (Adjustable thermal & magnetic release) - 01 Nos (Incomer) (b) MCCB 160 Amps, 4 pole with breaking capacity 25 KA (Adjustable thermal & magnetic release) - 01 Nos (outgoing) (c ) MCCB 100 Amps 4 pole with breaking capacity 25 KA (Adjustable thermal & magnetic release) - 08 Nos (outgoing) (d ) MCCB 63 Amps 4 pole with breaking capacity 25 KA (Adjustable thermal & magnetic release) - 08 Nos (outgoing) (e) Multifunctional meter Cat No 30332567 MAKE schneider (f) Moulded fuse holder 125 A including HRC fuses = 3 Nos (g) Indicator lamp RYB : 01 Set (h) CT'S 400/5 01 Set Make-L&T (j) Panel drawing shall be got approved from GE before placing order.

S&F in replacement, LT switch gear 440 Volts 3 phase, 4 wire 50 cycles, cubicle or truck type complete with MCCB, 63 Amps, 16 KA, ICS = 100% ICU, with adjustable thermal - Magnetic Release, including spreader terminals, phase barriers complete all as specified and directed by Engr-in-Charge.

S&F in replacement, LT switch gear 440 Volts 3 phase, 4 wire 50 cycles, cubicle or truck type complete with MCCB, 100 Amps, 35 KA, ICS = 100% ICU, with with adjustable thermal - Magnetic Release, including spreader terminals, phase barriers complete all as specified and directed by Engr-in-Charge.

S&F in replacement, LT switch gear 440 Volts 3 phase, 4 wire 50 cycles, cubicle or truck type complete with MCCB, 160 Amps, 36 KA, adjustable type , including spreader terminals, phase barriers complete all as specified and directed by Engr-in-Charge.

S&F in replacement, LT switch gear 440 Volts 3 phase, 4 wire 50 cycles, cubicle or truck type complete with MCCB, 200 Amps, 36 KA, adjustable type including spreader terminals, phase barriers complete all as specified and directed by Engr-in-Charge.

S&F in replacement, LT switch gear 440 Volts 3 phase, 4 wire 50 cycles, cubicle or truck type complete with MCCB, 250 Amps, 36KA adjustable type including spreader terminals, phase barriers complete all as specified and directed by Engr-in-Charge.

S&F in replacement, LT switch gear 440 Volts 3 phase, 4 wire 50 cycles, cubicle or truck type complete with MCCB, 400 Amps,36 KA adjustable type including spreader terminals, phase barriers complete all as specified and directed by Engr-in-Charge.

S&F in replacement, LT switch gear 440 Volts 3 phase, 4 wire 50 cycles, cubicle or truck type complete with ACB, 630 Amps, 50 KA adjustable type including spreader terminals, phase barriers complete all as specified and directed by Engr-in-Charge.

S&F in replacement, LT switch gear 440 Volts 3 phase, 4 wire 50 cycles, cubicle or truck type complete with ACB, 800 Amps, 50 KA adjustable type including spreader terminals, phase barriers complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Aluminium bus bar with insulators suitable for three phase and four wire LT AC, 50 Hz 415 V 1500 A capacity complete with powder coating, necessary internal electric connection as required complete all as specified and directed by Engr-in-Charge.

Description all as per item Srl No. 10.00 here in before but capacity of 1000

Description all as per item Srl No. 10.00 here in before but capacity of 800

Description all as per item Srl No. 10.00 here in before but capacity of 600

Description all as per item Srl No. 10.00 here in before but capacity of 400

Description all as per item Srl No. 10.00 here in before but capacity of 200

Supply and fixing in repair on load change over switch 400 Amps capacity, 415 Volts, 50 Hz, 4 Pole with advance neutral complete open execution type complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair on load change over switch 315 Amps capacity, 415 Volts, 50 Hz, 4 Pole with advance neutral complete open execution type complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair on load change over switch 250 Amps capacity, 415 Volts, 50 Hz, 4 Pole with advance neutral complete open execution typecomplete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair on load change over switch 200 Amps capacity, 415 Volts, 50 Hz, 4 Pole with advance neutral complete open execution type Make : Standard Cat No : ISCNFO0253

Supply and fixing in repair on load change over switch 100 Amps capacity, 415 Volts, 50 Hz, 4 Pole with advance neutral complete open execution type complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Intelligent Panel meter to measure voltage, current, frequency, power factor, etc on LT panel with all connected CTs complete all as specified and as directed by the Engineer in charge.

S&F in replacement of LED indicating lamps with colour Red, Yellow, Blue - 01 Set in LT panel with all connected CTs complete all as specified and as directed by the Engineer in charge.

S&F in replacement of Automatic 3 Phase 415 V, 50Hz, 500kW LT Distribution Control Panel (LBS) made up of MS plate with Aluminium Bus bar for Controlling and Monitoring the mains Supply from a centralized Location with Dimension of 8 x 13 x 2ft (H x W x D) Rectangular shape complete all as specified and as directed by the Engineer in charge.

Excavation in trenches in hard / dense soil not exceeding 1.5 mtr in depth and not exceeding 1.5 mtr wide and getting out including trimming of sides, for laying of cables & foundation of poles, stay assembly, complete all as specified and directed by Engr-in-Charge.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick, complete all as specified and directed by Engr-in-Charge.

Removing excavated material to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point, complete all as specified and directed by Engr-in-Charge.

M&L for factory made un-reinforced pre cast concrete cable protection cover LV class type - I with size 250mm x 150mm x 40mm laid across the cable (i.e. width of cover along the length of cable) for UG cable protection on the top of the sand cushioning, complete all as specified and directed by Engr-in-Charge.

M&L for sand cushioning with layer of sand 8cm thick before laying of cable and 10cm after laying of cable in trenches complete all as directed and sand cover to UG cable complete all as specified and directed by Engr-in-Charge. Note:- Only punned thickness shall be measured and paid.

Supply, laying, testing and commissioning of LT UG cable XLPE insulated PVC sheathed galvanized steel strip armoured electric power cable with stranded aluminium conductor 35 Sqmm 3.5 Core 1100 volts grade confirming to IS:7098 (Part-I), suitable for earthed system, laid in duct/trench/along pole/wall etc including nuts, bolts, washers, saddles & screws etc and making connection complete all as specified and directed by Engr-in-Charge.

Description all as per item Srl No. 29.00 here in before but 50 Sqmm 3.5 Core

Description all as per item Srl No. 29.00 here in before but 70 Sqmm 3.5 Core

Description all as per item Srl No. 29.00 here in before but 95 Sqmm 3.5 Core

Taking out Old UNSV earthing and M&L for Earthing complete with GI plate electrode of size 600x600x6 mm thick buried directly in ground with earth pit not less than 2.25 meter deep below ground level with top edge of plate not less than 1.5 meter below normal ground level connected to steel earth STRIP 32X6MM up to 7.5 mtr by means of nuts, bolts, check nuts, washers of tinned brass, protected by galvanized iron pipe 40mm bore (Medium grade) all as directed including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 42 x 42 x10cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 30 cm long, bent to shape as lifting handle, funnel, wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering,including charcoal or coke and salt in alternate layers and filling earth pit with fresh vegetable soil below copper plate and above upto ground level as required and necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR Part I including testing on completion all complete as specified and directed. Note: (i) Charges for earth resistivity test deemed to be included in the quoted rate. (ii) Earth resistance value shall be less than 1.0 ohm)

Taking out old unserviceable/serviceable un-reinforced concrete PCC cable covers from excavated trench complete all as specified and directed by the Engineer-in-Charge. Note:- Serviceable un-reinforced concrete PCC cable cover kept in safe custody for reuse at site and unserviceable un-reinforced concrete PCC cable cover through in low lying area.

Supply, laying, testing and commissioning of LT UG cable XLPE insulated PVC sheathed galvanized steel strip armoured electric power cable with stranded aluminium conductor 10 sq mm 2 core1100 volts grade confirming to IS:7098 (Part-I), suitable for earthed system, laid in duct/trench/along pole/wall etc including nuts, bolts, washers, saddles & screws etc and making connection complete all as specified and directed by the Engineer-in-Charge.

Description all as per item Srl No. 35.00 here in before but 16 Sqmm 2 Core

Description all as per item Srl No. 35.00 here in before but 25 Sqmm 3.5 Core

S&F galvanized iron pipe of 40 mm nominal dia light grade fixed to poles with clamps nuts, bolts and washers or laid under road crossing or fixed to wall including painting with two coats of aluminium paint over a coat of red oxide paint, complete all as specified and directed. Note : The cost of MS clamp, nut, bolt, washer and GI fittings etc shall be inclusive in the item rate.

Dismantling and taking down unserviceable / defective street light fitting / Flood light fitting of any wattage alongwith mounting bracket, flat iron clamp, nuts bolts etc from overhead LT poles complete all as directed.

S&F LED street light luminaire of 60 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection complete all as specified and directed by Engineer in charge.

S&F LED MCPCB, Single Sided,luminaire of 60 Watt capacity, suitable as per existing sample, IP 66, and incl making all electric connection complete all as specified and directed by Engineer in charge.

S&F LED Street Light LED DRIVER 50/60W BIS APROVED, For Flood Light, suitable as per existing sample, IP 66, and incl making all electric connection complete all as specified and directed by Engineer in charge.

S&F LED street light luminaire of 90 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection complete all as specified and directed by Engineer in charge.

S&F LED MCPCB, Single Sided,luminaire of 90 Watt capacity, suitable as per existing sample, IP 66, and incl making all electric connection complete all as specified and directed by Engineer in charge.

S&F LED Street Light LED DRIVER 90/100W BIS APROVED, For Flood Light, suitable as per existing sample, IP 66, and incl making all electric connection complete all as specified and directed by Engineer in charge.

S&F in replacement of street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with and incl 02 nos MS clamp made of MS flate iron of 50 x 6 mm size with nut, bolts, washer etc with and incl two coats of aluminum paint over a coat of red oxide primer complete all as specified and directed by Engineer in charge.

S&F LED flood light luminaire of 200 Watt capacity, 24000 Lumen, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection complete all as specified and directed by Engineer in charge.

S&F LED flood light luminaire of 150 W 6500K Cool Day White, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection complete all as specified and directed by Engineer in charge.

S&F LED flood light luminaire of 100 Watt capacity, 6500 Lumen, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection complete all as specified and directed by Engineer in charge.

S&F LED 5 W Spike Light IP65 Warm White SPIDER 101 with die cast aluminium housing and polycarbonate opal diffuser and IP protection and incl making all electric connection, complete all as specified and directed by Engineer in charge.

S&F LED 25 W Ruby Mini Post Top LED Lamp 6000 K with die cast aluminium housing and polycarbonate opal diffuser and IP protection and incl making all electric connection complete all as specified and directed by Engineer in charge.

M&L for preparation old (exposed) painted surfaces of existing LT steel tubular street Light pole, struts including cross arms, clamps etc complete and applying two coats of aluminium paint over a coat of red oxide primer over the ground and making 30cm wide strip with black and yellow paint including numbering of HT/LT poles at a height of 1.5 mtr above ground level as per existing having 15mm width and 50mm bold letter complete all as specified and directed including Marking Red Stipn painting on HT Poles etc. complete all as specified and directed by Engineer in charge.

M/S SHEYSHAN ENTERPRISES (BID ID -3297113)

M/S TRADE LINK (BID ID -3294373)