SPECIAL REPAIR TO BUILDING NO P-3/83 (01 TO 08) AND P-3/84 (05 TO 08) OR MD ACCN OF MED REGT AT MIL STN JAMMU UNDER GE SATWARI

Amount

Taking down chowkats or frames with shutter (without taking off shutter from the frame) n.exc 1.5 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and as directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 Sqm & n.exc 4 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and as directed.

Taking down shutters of any description exc 1.00 Sqm and n.exc. 2.00 sqm each and refixing in the same opening complete all as specified and as directed.

Providing & fixing of windows made of pre-painted steel Double Rebate Windows/Ventilators (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72 mm x 55 mm, centre mullion should be of 72 mm x 50 mm, section for fixed glass beading should be of 12 mm x12 mm and section for shutter should be of 52mm x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20 mm x40 mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap, stay, handles 2 nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The quoted rate including windows should be paneled with 4 mm thick plain float glass for windows and frosted glass for ventilator and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of 04x holdfasts as fasterner in each windows, Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished item of work including of all taxes.

Pressed steel frames of size 105mm x 60mm made out of size 1.25mm thick MS sheet for doors single rebatedincluding mild steel 04x hinges (02x at top,01x midldle,01x bottom) medium weight 100 mm long and 25mm x 3mm flat iron in 06x holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including one coat of red oxide primer complete all as specified and as directed.

Pressed steel frames of size 125mm x 60mm made out of size 1.25mm thick MS sheet for doors double rebated including mild steel 08x hinges(04x at top,02x midldle,02x bottom) medium weight 100 mm long and 25mm x 3mm flat iron in 06x holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregates including one coat of red oxide primer complete all as specified and as directed.

Pressed steel cup board frame of MS sheet 1.25 mm thick size of frame 60mm x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregates as in filling to back of chowkats including butt hinges 100 mm long. Piano hinges measured separately.

Cement concrete 1:2:4 type B-O using 12.5 mm graded crushed stone aggregate as in back fill of pressed steel door frames complete all as specified and as directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm Plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all as specified and as directed.

Stainless steel door 304S grade factory made Box type hollow section 0.80 mm thick, size for vertical and top rail 100mm x 35mm, size of middle rail 150mm x 35mm and bottom rail of size 200mm x 35mm single rebated comprises wire gauged skelton shutter incl 2 Nos 150mm S/S handles, 200mm S/S tower bolts( 02 Nos) and 01 No 300mm long S/S sliding door bolt. complete all as specified and directed. Note:- wire gauged to be measured and paid Separately.

35 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

35mm thick 2nd Class hard wood glazed,gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitred and rebated sash bars,stiles and rails as specified in SSR 2009 Part-I Sec 8 clause 8.24 (a) complete all as specified and as directed.

Factory made solid panel PVC door shutter 30 mm thick( style ) consisting of frame work made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour P.V.C‘ C’ channel having a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement complete all as specified and as directed.

Prelaminated HDF board 18/19 mm thick as in shutters/shelves (exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including 2mm thick PVC edge banding of same colour of HDF board fixing with nails/rasin around the shutter complete all as specified and as directed.

Factory made 5mm thick PVC Sheet of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. paneling for back side (wall side) and also manufacurer's test report and test certificate is mandotary with each and every supply of the material complete as per manufacturer's specifications complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed.

Framed work as in doors or gates and water tank stage,Cooler Stand, balacony railing and similar work etc with angle or other section, tubular pipe (circular/rectangular) with flat and square guard bar, rails, braces, etc.complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding including necessary cutting in bricks/concrete wall and fixed with hooks and hinges or steel hanging door fittings and fastening and fixing FE 290 Gde E-165 complete all as specified and as directed.

Stainless steel works of flat iron, square bar, round bars etc. as in framed work such as grills, guard bars, gratings etc incl bending, cutting and welding complete all as specified and as directed.

Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified and as directed.

Butt hinges of stainless steel cold rolled medium weight of size 100mm complete all as specified and as directed.

Aluminium handles,fabricated type, anodised Size- 125mm, anodised section and fixed complete all as specified and as directed.. (ISI Marked)

Aluminium anodised, barrel tower bolts size 200 mm of extruded section and fixed complete all as specified and as directed.. (ISI Marked)

Aluminium alloy, anodised, sliding door bolt Size- 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed..

Mild Steel helical ordinary rat tail rod pattern spring 150mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work complete, fix in repair all as specified and as directed.

Aluminium hanging floor door stopper,Twin rubber stopper,size 100mm , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete all as specified and as directed.

25mm outer dia Stainless steel chromium plated decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with Stainless Steel designed finials (Design approved by GE) for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

continuous (piano) hinges 30mm , heavy duty mild steel, bright finish or electrogalvanised suitable for 19mm thick shutter and fixed, complete all as specified and as directed.. ( ISI Marked)

Hasp & staple safety type Stainless Steel with S/S hinges Spin including bolt to hinges plate fixed with screws of 75 mm in length.

50 mm magnetic catches with brass body and striking plate including letting in as fixed complete all as specified and as directed.

100 mm long Stainless Steel glossy finish handles with SS screw, complete all as specified and as directed.

Roughening surfaces of old concrete floor or old plastered skirting by picking, sweeping clean and washing down with water to remove dust etc and brushing surface with neat cement slurry with 3.0 kg of cement per sq. metre, removing serviceable tiles to store and rubbish off the Cantt area complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding, terrazzo dado from wall surface (but not backing), removing serviceable tiles to store and rubbish off the Cantt. area. complete all as specified and as directed.

Taking down cement plaster on brick or stone walls or stone walls etc, including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed. (Note :- Work will be carried out up to 4th storey with necessary scaffolding).

Material and labour Ceramic edge cut coloured or printed light shade tiles 08 to 10 mm thick (square/ rectangular) polished area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

All as per item srl No. 34 above but as in vertical surfaces dado/skirting over and including a backing coat of CM 1:4, 10 mm thick complete.

Material and labour Non - skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed.

Material and labour glazed ceramic coloured Digital tiles in vertical surface 300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 complete all as specified and as directed.

Machine cut kota stone slab flooring 20-25mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and Mirror polishing complete,laid over and including screed bed or bedding layer of 20 mm thick in cement mortar (1:4) complete all as specified and as directed.

Machine cut kota stone single piece18-20mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rounding/moulding of edges at tread and riser during rubbing and mirror polishing set and jointed in neat cement slurry and pointed in white or colour cement to match, the shade/colour of tiles over and including 10 mm thick rendering in cement mortar 1:4, as in riser of steps,skirting,dado & vertical surfaces complete all as specified and as directed.

Dismantling of concrete by chiseling from RCC members like column , beam, parapet facia, chajja, ceiling,etc exposingthe reinforcement without disturbing the reinforcement free from rust by sand blasting/using chemical , apply a coat of rustolin to remove rust and acralic polymer on old rusted reinforcement proving at places addl reinforcement welding with existing reinforcement as directed wherever required binding RCC 50 mmx50 mm (10 mm gauge welded mesh ) & tack , securing with clips / blinding wire, welding & provision guniting pressure 2.2 to 2.5 kg /sqm with admixer 1 cement 3.5 of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control neccssary form work & scaffolding up to four storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick plaster with chicken wire mesh in cement mortar 1:4 with water proofing compound @3% by weight of cement and recron 3 S as per manufacturer instruction cleaning & removing of waste meterial etc and apply two coats of Dr fixit /pidilite/sika/Fosroc new coat ezee at interval of 8 hours cure for the surfaces complete all as specified and as directed.

Demolition of reinforced cement concrete of any discription and any position( ground to 4th floors) and removing the rubbish from the work site out side defence premisescomplete all as specified and as directed.

Reinforced concrete 1:2:4 nominal mix type B1 ( using 20 mm graded crushed stone aggregates) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like.

Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips.(Column footing , Column and PB)

Use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for fair finished surfaces of concrete, complete all as specified and as directed.

Use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n.exc. 20cm wide for fair finished surfaces of concrete, complete all as specified and as directed.

16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platform (01x hole drilled for gas pipe in each kitchen platform) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 15 mm thick CM 1:4 complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Complete removal of existing water proofing treatment of any description incl under layer, taking down of cement plaster,concrete and mud pushka of any thickness and removal of debris off the premises.

Plain cement concrete 1:2:4 type B-0 using 12.5 mm graded Crushed stone aggregate as in roof paddding,complete all as specified and as directed.

Cleaning of the exposed concrete slab and repairing the surface irregularities like cracks, potholes, as per manufacturers method statement by Berger HS Rapairo(or equivalent)along with HS Latex Plus(or equivalent)& cement in mixing ratio of 1:4 where ever required

Home Sheild PU Roofkoat(or equivalent)is a one component liquid ,solvent free ,cold applied , water-proofing membrane that is highly elastic and UV resistant with 10 years Warranty .ASTM D 6083-97a Waterproofing and heat reflecting systemhaving following key performance properties:1.UV resistant ,prevent yellowing and weathering2.Highly elastic upto 350% and crack bridging3.Excellent adhesion on porous and non-porous substrates4. Tensile Strength >10 N/mm2 with GeoTextile fleece5. Soler Reflective Index (SRI) more then 109-111 ASTM E1980-11System: First coat:Providing and applying primer over the prepared surface with HS PU roofkoat Primer(or equivalent)Coverage: 0.2kg/m2(with 50% dilution of water)Reinforcement: Geotextile 40 gsmSecond coat:Home sheildroofkoat(or equivalent)Consumption: 0.5 kg/m2.Third coat: HS PU roofkoat(or equivalent)Consumption : 0.8 kg/m2.System buildup-1.5kg/sqm with geotextile of 40gsmFor accessible roof, tiles with screed/ adhesive may be fixed thereafter.

Demolition of cement concrete in and paving (un reinforced) exc. 15 cm. thickness, below or above ground level, including removal of waste from defence land and dumping at a place as specified by civil authorities complete all as specified and as directed.

Glass fibre reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent).Base coat: Berger HS Latex plus (or equivalent)Consumption base coat: 0.3 kg/m2Reinforcement: Glass fiberSecond and Third coat: Latex sheild 2K (or equivalent)Consumption top coat: 3 kg/m2System requirements: density: 2.00 kg/ltr;compressive strength: 0.5 N/mm2.• Wall penetration through the RCC slab must be sealed using Berger HS RepirO(or equivalent).• Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus(or equivalent) modified mortar with a bonding coat of Berger HS Latexplus(or equivalent) modified cement slurry upto 5ft.• All depressions, unevenness, surface honeycombing shall be repaired using Berger HS Latex plus(or equivalent) modified polymer mortar with a bonding coat of Berger HS latex plus(or equivalent)modified cement slurry.Including cleaning of RCC surface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges, etc

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 with water proofing compound tobe finished even and smooth without usingextra cement complete all as specified and as directed (WPC to be measured separately)

40 mm dia G I tubing light grade galvanised laid over floors as a spout pipe in sunken floors complete all as specified and as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing unserviceable material from the work site ouside defence premises complete all as specified and as directed.

Supply only Liquid water proofing admixture complete all as specified and as directed of as per manufacturers instruction.

Dismantling water tanks and removing to store of water storage tanks exc 250 ltrs but n exc 500 ltrs complete all as specified and as directed.

Supply and fixing Rotational moulded polyethylene water storage tanks of 500 litres capacity,(cylindrical vertical with closed top) white in colour, hoisted and fixed in position all as specified in SSR 2009 Part-I (as per IS 12701-1996) including Ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed for 20 mm bore pipe (Minimum weight 20mm-210gms) , including making connections complete all as specified and as directed.

Gun metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed, Bore dia of 20mm complete complete, fix in repair all as specified and as directed.

75 mm thickness PCC 1:2:4 type -B-2 (using 40 mm graded crushed stone aggregate) complete all as specified and as directed.

75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings complete all as specified and as directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required completeas directed edges joint filling with in CM 1:4 complete including excavavtion for kerb stone as directed.

25mm thick PCC 1:2:4 type B1 using (20mm graded crushed stone aggregate) as in floor and finished rough to recive the floor tiles etc complete all as specified and as directed.

50mm thick cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and as directed.

Demolition of cement concrete (unreinforced) ground floor and pavings n exc 15 cm thickness (below or above ground level ) and removing the rubbish from the work site out side defence premises complete all as specified and as directed.

Taking up or down steel tubing of 15 mm bore pipe and connections,including cleaning for re-fixing or removal to store complete all as specified and as directed.

Taking up or down steel tubing of 20 mm bore pipe and connections,including cleaning for re-fixing or removal to store complete all as specified and as directed.

Supply and fixing GI tubes 'medium grade' galvanised, 15 mm bore, ISI marked with all fittings such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors Including cutting hole in brick/concrete wall complete all as specified and as directed. complete all as specified and as directed.

Supply and fixing GI tubes 'medium grade' galvanised, 20 mm bore, ISI marked with all fittings such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors Including cutting hole in brick/concrete wall complete all as specified and as directed.

Cutting chases, pinning in , making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings,steps,cills,sunshades,shelves,lintels etc,and cutting chases for concealed water tubing or concealed conduit wiring,etc,and making good,cutting n.exc 10cm girth in brick walls.

Angle valve with wall flange , cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, fixing in repair, complete all as specified and as directed.

CP Bib taps, 15mm dia fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fix in repair all as specified complete all as specified and as directed.

15mm dia CP brass wall mounted sink mixer swan neck type for mixing hot & cold water screwed down for iron pipe including necessary fitting fix in repair complete all as specified and as directed.

15mm dia CP Pillar taps long body swan neck type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixing in repair, complete all as specified and as directed.

15mm dia CP brass wall mixer 03-in-01 with provision of over head shower system (quarter turn) for mixing hot & cold water screwed down for iron pipe including necessary fitting fix in repair complete all as specified and as directed.

Chromium plated shower rose 125mm square size with arm 15mm dia 195mm long with bend 45 degree with brass flange, fixing in repair, complete all as specified and as directed.

Sinks made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 mm x 460mm, bowl size 410mm x 330mm x 160mm complete with waste coupling 100mm dia & PVC waste pipe fix in repair fixed complete all as specified and as directed.

Kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. The over all size (30"x36"x10") fixed with steel fastners or steel screw complete all as specified and as directed.

Vitreous chinaware white wash hand basin with pedestal of size 58cm X 45cm X82cm complete including CP Waste coupling ,waste pipe of 32 mm ,complete fixing arrangement and cutting for and pinning in walls & making good fix in repair complete all as specified and as directed.

Vitreous china wash down water closet pan (trap S/P type) (Pedestal pattern) white, including PVC Seat cover for EWC pan (White ) of standard quality including hinges bolt,fix in repair complete all as specified and as directed.

Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position fix in repair complete all as specified and as directed.

PVC valveless,syphonic action type, dual flushing cistern, low level,white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend for IWC and EWC of capacity 10 litres and making good to dismantled/damaged floor/surfaces, fixing in repair, complete all as specified and as directed.

Towel Rail 600mm long of stainless steel fixed with and includiing chromium plated brass screw and wooden/ Plastic cleats. (Minium weight 190gms)

Stainless steel Soap Dish/Oval suitable size complete all as specified and as directed..

Glass Shelf 450 mm long complete all as specified and as directed.

Dismantling PVC/Cement/CI pipes 50 mm to 110 mm dia including all fittings like bend,branch pieces, connectors, heel rest bend etc Incl Cutting through brick/RCC/PCC Wall and removing from site complete all as specified and as directed.

PVC (SWR) type B pipes 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed.

PVC (SWR) type B pipes 110 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30 mm wide 2 mm thick (having 100 mm clear space from wall) fixed to wall with nails at the spacing of 1.5 mtr centre to centre, complete all as specified and as directed.

PVC (SWR) type B pipes 75 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed.

PVC (SWR) , bends with access door for 75 mm bore , complete all as specified and as directed.

PVC(SWR) , bends with access door, for 110 mm bore complete all as specified and as directed.

PVC (SWR) 110mm branch piece, single (single Y) equal or unequal complete all as specified and as directed.

UPVC(SWR), junction single, (single 'T') equal or unequal for 75 mm bore , complete all as specified and as directed.

UPVC(SWR), junction single, (single reducer 'T') equal or unequal for 110mm x75 mm bore , complete all as specified and as directed..

PVC(SWR), junction single, (single 'T') with access door equal or unequal for 75 mm bore , complete all as specified and as directed.

PVC(SWR), junction single, (single 'T') with access door equal or unequal for 110 mm bore , complete all as specified and as directed.

PVC (SWR) , bends for 75 mm bore , complete all as specified and as directed.

PVC (SWR) Floor trap plain wih stainless steel grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregates complete all as specified and as directed.

PVC (SWR) multi floor trap plain with stainless steel grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregates complete all as specified and as directed.

UPVC (SWR) vent cowl 75 mm dia complete all as specified and as directed.

UPVC (SWR) vent cowl 110 mm dia complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoin, arches pillars but excluding ashlar facing dressed stone work and precast concrete article complete all as specified and as directed.

Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed.

Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 but except bricks

Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 complete all as specified and as directed.

Rendering 15 mm thick on fair faces of brick or concrete surface walls, in cement mortar 1:4 , rendering is to be finished even and smooth without using extra cement (up to 4th storey with necessary scaffolding complete all as specified and as directed.

Rendering 15 mm thick on fair faces of brick or concrete surface walls, in cement mortar 1:6 , rendering is to be finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 5 mm thick on fair faces of concrete surface of ceilings, in cement mortar 1:3, rendering is to be finished even and smooth without using extra cement complete all as specified and as directed.

Applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper to make surface even and smooth complete all as specified and as directed.

Applying two coats of synthetic enamel paint on new wooden surfaces of any description over a coat of pink primer having width/girth exceeding 10 cm complete all as specified including preparation and necessary filling by chalk putty as and where required to make surface even and smooth.

Applying one coat of synthetic enamel paint on old painted steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper to make surface even and smooth where requred complete all as specified and as directed.

Applying one coat of synthetic enamel paint on old painted wood surfaces of any description having width/girth exceeding 10 cm complete all as specified including preparation and where requered to make surface even and smooth.

Complete removal of existing treatment on wall/Ceilling,roof projectios,Including facia,cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. by skilled labour (up to 4th storey with necessary scaffolding) complete all as specified and as directed.

Waterproof cement based putty @ 1 Kg(undiluted) per sqm. of average thickness 1 mm over the plastered/old painted surface of wall/ceilling (up to 4th storey with necessary scaffolding) after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps:- Step 1) Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2) Apply the putty manually in double layer and finishing the surface even and smooth in level without any undulations. 3) Allow 6-8 hrs time to dry the putty surface.

One coat of acrylic waterbased interior/exterior (wall/ceilling up to 4th storey with necessary scaffolding) grade primer @ 0.8 ltr(undiluted)/10 sq mtrs diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface for painting of subbsequent coats complete all as specified and as directed.

Preparing the putty surface by sanding paper and applying two coats of oil bound distemper on wall/ceilling (up to 4th storey with necessary scaffolding) using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and as directed.

Water based premium acrylic smooth exterior emulsion for approved colour (up to 4th storey with necessary scaffolding) with silicon additive excellent dirt pickup resistance with low VOC less than 50 AntifugalAnti Algai properties in two coat @1.79 litre (unndiluted) /10 sq mtrs diluted with water as per manufacturer instructions applied over priming surface with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in between subsequent coats of paint complete all as specified and as directed.

Taking down carefully aluminium conductor point wiring (light, fan, light socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLS insulated and sheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 sqmm multistranded copper conductor FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked terminated into GI/pressed steel modular terminal boxes including modular switch cover IS marked for mounting modular switches, sockets, fan regulators etc complete all as specified and as directed.

One light/fan point controlled by one, one way switch 6 Amp complete

do but one 3 pin modular socket outlet 6 amp independent board

do but one 3 pin modular socket outlet 6 amp on same board

All as per srl item No 121 above but for one 3 pin modular socket outlet 15/16 Amps independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

One bell/ buzzer point controlled by one push button on same board with other switches or independent with cable 1.5 sqmm sizecomplete all as specified and as directed.

Switch modular one way 06 Amp,1 module complete all as specified and as directed.

Switch modular one way 16 Amp,1 module complete all as specified and as directed.

Modular socket 6A-2/3 Pin 2 module 230V AC complete all as specified and as directed.

Modular socket 6A/16A-3 Pin 2 module 230V ACcomplete all as specified and as directed.

Modular bell push type one way 6 Amp 1 module complete all as specified and as directed.

Bell Ding Dong AC 230 volts Single Phase complete all as specified and as directed.

Modular type fan regulator 2 Module complete all as specified and as directed.

Lamp holder, Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Ceiling rose surface, backelite, three terminal, 240 volts complete all as specified and as directed.

LED light fitting 1 x 10 Watt, 220 V AC, 2 feet decorative box type with connecting up with flexible copper conductor cable of suitable size complete all as specified and as directed.

LED light fitting 1 x 20 Watt, 220 V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

MCB SPN complete 40-63Amp with rupturing capacity 10 KA 'C' series, complete all as specified and as directed.

MCB single pole 6 to 32 Amp with rupturing capacity 10 KA 'C' series complete all as specified and as directed.

Distribution Board (SPN) double door 08 Way and should be IP 54 protected with Bus bar, Earth Bar, neutral Bar complete all as specified and as directed.

Sub main wiring with single core cable 2 x 4 sq mm FRLS insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1x4 Sq mm FRLS insulated unheathed copper conductor cable as earth wire connected with main earth dolly including chiseling, cutting & making good to match with the existing surfacecomplete all as specified and as directed.

Galvanised steel earthing complete with 60 cm x 60 cm x 6 mm thick galvanised steel earth electrode and 04 mm dia galvanised earth lead wire burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to earth lead 4.0 mm dia GI wire protected by 15 mm bore light grade galvanised iron pipe and other and connected to test point as directed including funnel with watering pipe 20 mm bore light grade galvanised iron wire mesh, charcoal and common salt in alternater of 15 cm complete thickness all around the GI plate electrode complete with earth pit PCC 1:3:6 type CI and RCC cover and necesary excavation and earth work in hard/dense soil and disposal of spoil to a distance not exc 50 mtr and necessary testing complete all as shown in electorical plate No 03 connected to earthing test point including following elements/works complete all as specified and as directed.

M/S Jasbir Singh (BID ID -3355663)

NARESH KUMAR AND COMPANY (BID ID -3363220)

M/S VED PAUL MAHAJAN (BID ID -3358033)

M/S Shesh Paul Gupta (BID ID -3349216)

THAKUR BUILDERS AND CO (BID ID -3363361)