GE/863/EWS-T-50 OF 2020-21

Amount

Dismantling of wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness including cover fillets all as specified and directed.

Dismantling timber scantlings 40 sq.cm and over in section, in any positions as in framed work complete all as specified and directed.

-Ditto- all as per item above but in fillets, rails, posts, rafters, purlins, etc under 40 sq.cm in section complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quions, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) 150mm dia set in cement mortar complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) 100mm dia set in cement mortar complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Taking down chowkats or frames not exc 1.5 sq.m each but with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sq.m but n.exc 4 sq.m each but with shutters (without taking off shutters from the frames) complete all as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

M & L for second class hardwood clean sawn scantlings as in timber framed and fixed complete all as specified and directed.

-Ditto- all as above but except timber.

M & L for 6mm thick (No of ply 5) plywood, grade BWR, type BB, fixed with nails to timber frame work as in ceiling, flat or sloping complete all as specified and directed.

M & L for 6mm thick (No of ply 5) plywood, grade BWR, type BB, fixed with nails to timber frame work as in partitions / shutters complete all as specified and directed.

M & L for second class hardwood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc 3 & n.exc 6 sq.cm complete all as specified and directed.

-Ditto- all as above but bull nosed, splayed, chamfered or rounded on one edge or face.

M & L for second class hardwood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc 13 & n.exc 25 sq.cm complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation, filling in mass concrete complete all as specified and directed.

M &L for pre-cast cement concrete type C1 1:3:6 using 20mm graded stone aggregate as in block masonry with solid blocks, exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 but EXCEPT STONE complete all as specified and directed.

M & L for providing precast cement concrete Type C1 1:3:6 using 20mm graded stone aggregate and set in cement mortar 1:6 as in bond stone complete all as specified and directed.

M & L for providing cement concrete Type C1 1:3:6 using 20mm graded stone aggregate as in coping including necessary formwork complete all as specified and directed.

M & L for providing reinforced precast cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate in cover slab for man holes & septic tanks with plain faces set in CM 1:6 complete all as specified and directed.

M & L for non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M & L for glazed ceramic coloured tiles in vertical surface 300 x 200 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed bed in cement mortar 1:3 complete all as specified and directed.

M & L for chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick, set, jointed and pointed in neat cement slurry over and including 20mm thick screed bed in cement mortar 1:4 as in floors with grey cement and pigment complete all as specified and directed.

M & L for proving cement concrete type C1 1:3:6 using 20mm graded aggregate as in roof kerb or mud stops, round on edges complete all as specified and directed.

M &L for 50 mm thick cement concrete type C-2, 1:3:6 using 40mm graded stone aggregate finishing surface even and smooth without using extra cement as in plinth protection complete all as specified and directed.

M & L for PCC 1:4:8 type D-2, 75mm thick, using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M & L for PCC 1:2:4 type B-1, 25mm thick, using 20mm graded stone aggregate as in surface of flooring finishing surface even and smooth without using extra cement all as specified and directed.

M & L for RCC 1:2:4 type B-1 ( 20 mm graded stone agg ) as in chajjas complete all as specified and directed

M & L for RCC 1:2:4 type B-1 ( 20 mm graded stone agg ) as in Beams , cantilevers, bressummers, lintels etc complete all as specified and directed

M & L for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges in rough finished flat surface of concrete complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, bands, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

S & F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe-290 (Gde E- 165) complete all as specified and directed.

S&F Fe-410-W(Gde- E-250) quality-B Roof trusses (framed) ,trussed, purlings, crane gantries, rails and fastenings and heavy bracket framing (Beam , tee, angle ) channel or flat sections ) including distance pieces , cleats complete all as specified and directed.

S & F of 0.63 mm thick galvanized corrugated iron (CGI) sheeting with two corrugation side lap using grade of zinc coating -275. inclusive of both sides, fixed with ‘L’ or ‘J’ type hooks or cranked hook / bolts and washers as in roof covering etc. complete all as specified and directed.

S & F of 2mm thick Fiber glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

M & L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 using WPC 3% by weight of cement and finished surface even and smooth (without using extra cement) complete all as specified and directed. NOTE: - water proofing compound shall be measured and paid separately as 'supply only'.

Supply only integral water proofing compound of approved brand / make complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on concrete block masonry finishing even and smooth without using extra cement complete all as specifed and as directed

M&L for 10 mm thick rendering in cement mortar 1:6 on concrete block masonry finishing even and smooth without using extra cement complete all as specifed and as directed

M & L for Raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar 1:3 complete all as specified and directed.

M & L for rendering 10mm thick on fair faces of brick or concrete surfaces in cement plaster 1:6 and finished even and smooth (without using extra cement) complete all as specified and directed.

S & F second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F second class hardwood 35 mm thick plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers and fitted to chowkats complete all as specified and directed.

S & F of 35 mm thick (Batten thickness) 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule part – I (Specifications - 2009) complete all as specified and directed.

S & F of 30 mm thick (Batten thickness) 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule part – I (Specifications - 2009) complete all as specified and directed.

S & F clamps, hold fast, hook washer & similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M & L for providing cement concrete type C1 1:3:6 using 20mm graded stone aggregate as in hold fast blocks complete all as specified and directed.

S & F 125mm butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and directed.

-Ditto- all as per item above but 75mm long.

S & F 300mm length aluminium alloy, anodised, sliding door bolt hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S & F 150mm Aluminium handles, cast type, anodised complete all as specified and directed.

S & F 125mm Aluminium handles, cast type, anodised complete all as specified and directed.

S & F 150mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S & F 125mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S & F mild steel 300mm ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

M & L sheet glass, 4mm thick ordinary quality and glazing with oil putty or beadings in square not exc 0.5 sqm in each pane complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

M & L for preparation of new plastered surface of wall and applying two coats of distemper oil emulsion over a coat of chalk whiting as a preparatory to distempering complete all as specified and directed.

M & L for preparing newly plastered or previously untreated walls surfaces and applying two coats of cement base paint complete all as specified and directed.

M & L for preparation of newly plastered or un-plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparation of wood and wood based materials, new or old surface of any description and girth not otherwise described and treated with two coats of creosote oil complete all as specified and directed.

M & L for preparation of new wooden surface any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

-Ditto- all as per above but one coat of synthetic enamel paint on old wooden surfaces of any description complete all as specified and directed.

M & L for preparation of new or previously untreated surfaces of steel of any description , over 10 cm in width or girth not otherwise described applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and directed.

-Ditto- all as per item above but one coat of synthetic enamel paint on old steel surfaces of any description complete all as specified and directed.

S & F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.complete all as specified and directed.

M&L for 100 mm internal dia salt glazed stone ware pipe Grade 'A' laid in trenches and jointed complete all as specified and directed.

M & L for cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in bed to drain pipes of 100 mm bore including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

M & L for Gully traps salt glazed stoneware (SGSW) square or round mouthed type 'P' of size 180x100mm for drain pipes complete all as specified and directed.

M&L for 150 mm internal dia salt glazed stone ware pipe Grade 'A' laid in trenches and jointed complete all as specified and directed.

M& L for cement concrete 1:4:8 type D-2, (using 40mm graded stone aggregate) as in bed of drain for 150mm bore pipe incl packing under and completely surrounding pipes with concrete after they are laid and tested for 150mm dia pipes complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 110 mm dia bore PVC (SWR) bends any radius complete all as specified and directed.

S & F 110 mm dia bore PVC (SWR) bends with access door any radius complete all as specified and directed.

S & F 110 mm dia bore PVC (SWR) junction single 'T' equal or unequal complete all as specified and directed.

S & F 110 mm dia bore PVC (SWR) junction single 'T' equal or unequal with access door complete all as specified and directed.

S & F PVC (SWR) 110 mm bore vent cowl complete all as specified and directed.

M & L for cement concrete type B-2, 1:2:4 (using 40 mm graded stone aggregate) as in surface channel or drain or benching in manhole complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

Construction of 50 users Septic tank to carry sewage and sludge water, complete all as specified and shown in Drg No. STD 1320 (C) Sheet 1/3 to 3/3 of Chief Engineer Chandigarh Zone and directed. Note:- (a) Excavation and earth work shall be in any type of soil. (b) Precast cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) block masonry with solid blocks, set in CM 1:4 shall be used in walls in lieu of Brick masonry / stone masonry as shown in drawings. (c ) The width of Precast cement concrete (20mm graded stone aggregate ) type C-1 block masonry in walls shall be as 700 / 600 / 500 / 400 mm in lieu of width of Brick masonry 690 / 575 / 460 / 345 mm respectively as shown in drawings. (d) RCC work where ever shown in drawings as in base slab, baffle walls , Vent shaft, manhole openings with cover connection, roof slab etc . shall be RCC 1:2:4, type B1 using 20 mm graded stone aggregate. (e) The cost of all above provisions and other provisions as shown in drawings shall be deemed to be included in quoted rates of this item and nothing extra shall be entertained on this account.

Construction of Soakage well 1.80 m dia and 3.0 m effective depth complete all as specified and shown in Drg No. STD 1173 (C) Sheet 1R/2 of Chief Engineer Chandigarh Zone and as directed. NOTE:- (a) Excavation and earth work shall be in any type of soil. (b) Foundation in PCC 1:3:6 type C2 using 40 mm graded stone aggregate. (c) Honey combing brick walls masonry as shown in drawing. (d) Brick bats filling as shown in drawings (e) RCC work where ever shown in drawings shall be RCC 1:2:4, type B1 using 20 mm graded stone aggregate (f) The cost of all above provisions and other provisions as shown in drawings shall be deemed to be included in quoted rates of this item and nothing extra shall be entertained on this account.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

Taking down carefully copper/aluminium point wiring from existing points (light, fan, socket or power) along with compete fittings such as switches ,ceiling rose, pendent holder, sketch fitting & regulator etc. including making good to the disturbed surfaces of wall, roof and floor etc. to match with the existing surfaces complete all as specified and directed.

Taking down unserviceable submain wiring and service cable along with batten /PVC conduits etc. and making good disturbed surfaces of walls/floors and match the existing surface complete all as specified and directed.

Taking down unserviceable main switches, DBs with MCB SP/Isolators by unscrewing form board complete all as specified and directed.

M&L for point wiring using approved colour coding as per IS by using FRLS PVC insulated 1.5 Sqmm multistranded,1100 volt grade copper conductor cable, unsheathed type along with FRLS PVC insulated 1.5 Sqmm multistranded copper conductor cable for continuous earthing in & incl PVC casing & caping with accessories having ISI mark fixed on wall surfaces / ceiling including provision PVC Box on top for fixing switches sockets etc. all as specified for one light point/ fan /Bell point controlled by one switch complete all as specified and directed.

All as per Srl item No 100 here-in-before but controlled with one 3 pin socket outlet 5 Amp on same board with other switches with cables 1.5 Sqmm.

All as per Srl item No 100 here-in-before but controlled with one 3 pin socket outlet 5 Amp on the independent board with other switches with cables 1.5 Sqmm.

All as per Srl item No 100 here-in-before but controlled with one 3 pin socket outlet 15 Amp, independent board with cable 2.5sqmm including provision of 2.5 sqmm single core multistanded FRLS PVC insulated copper conductor as earth conducting conductor.

Supply and fixing of switch piano type 15 Amp, 230 Volt, flush button single pole one way complete all as specified and directed.

Supply and fixing of socket outlet 6 pin 5/ 15 Amp 2-in-one 230 Volt flush type complete all as specified and directed.

Supply and fixing of socket outlet 5 pin 5 Amp 2-in-one 230 Volt flush type complete all as specified and directed.

Supply and fixing of switch piano type 5 Amp, 230 Volt, flush button single pole one way complete all as specified and directed.

M&L Ceiling rose, 3 terminal with ISI mark complete all as specified and directed.

Supply and fixing surface & wall mounted LED 20W tube light fitting batten 4 feet with extruded aluminium housing and robust construction 20W system lumen with all accessories complete all as specified and directed. Make : Cat No. BLRB-DB 118 of BAJAJ or equivalent as approved.

Material and labour for lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fixing LED lamp 9W system lumen (NOM) 600 with all accessories complete all as specified and directed. Make : Cat part No -LED 9DFCDL-PRO-BO of Cromptom or equivalent as approved.

S&F energy saving new generation 10W LED IP65 bulk head luminaire with opal diffuser powered with high power LED as light source complete all as specified and directed.

Supply and fixing of sheet metal enclosure (DBs) double door for single pole and neutral 8 way 240 volt with bus bar, neutral and earth link complete all as specified and directed.

S&F MCB SPN 16 Amp with rupturing capacity 10 KA 'C' series complete all as specified and directed.

S&F MCB SPN 32 Amp with rupturing capacity 10 KA 'C' series complete all as specified and directed.

S&F sub main wiring with single core cable 2 x 6 sqmm FRLSH PVC insulated unsheathed stranded copper conductor cable 1100 volts grade in rigid PVC caping casing medium grade along with 1 x 4 Sqmm FRLSH PVC insulated unsheathed copper conductor cable as earth wire connected with main earth duly including chiseling, cutting, & making good to match with the existing surface complete all as specified and directed.

Supply and fixing 1100 Volts grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire including one twin core cable flat or circular of size 16 Sqmm complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.3 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised iron wire 4.0 mm dia as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of SSR-2009 (Part-I) connected to earthing test point including funnel with wire mesh, PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) chamber, PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) cover 80 mm thick , GI watering pipe 20 mm dia, medium grade, 15 mm dia GI protection pipe, light grade and adequate quantity of salt and charcoal, with necessary excavation, earth work and formwork and testing on completion, complete all as specified and directed. Note: GI earth wire upto 7.5 Mtr is deemed to be included in the quoted rate.

Net Contract Sum will be after deducting Sch Of Credit of Rs. 74867.50

M/S Gulab Singh

M/S PYARE LAL

M/S Shamsher Negi Dewa