Supply and fixing of Furniture for Government Medical College Doda (Ghat).

Amount

Supply Installation and Assembly of CUBICLE WORKSTATIONS - 2400 X 1500 having panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. Tiles on main spine: Combination of top tiles shall be split fabric magneitc/fabric/split fabric tackable/split white board tile. Bottom tiles - Plain metal. INTERMEDIATE BLOCKS on main spine Intermediate blocks shall be given in DL + DL finish. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. MODESTY PANELS WITH ASSEMBLY LEG - 25 MM THK PLB modesty should be given on the front of the main worktop which shall be attached to the partition on one end with gable end bkts and on the other end with metal powder coated frontier leg. Legs - Metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - Main table recta out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 600 mm d and ERU table recta of size 900 mm w x 450 mm d.

Supply Installation and Assembly of CUBICLE WORKSTATIONS - 2400 X 1500 having panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. Tiles on main spine: Combination of top tiles shall be split fabric magneitc/fabric/split fabric tackable/split white board tile. Bottom tiles - Plain metal. INTERMEDIATE BLOCKS on main spine Intermediate blocks shall be given in DL + DL finish. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. MODESTY PANELS WITH ASSEMBLY LEG - 25 MM THK PLB modesty should be given on the front of the main worktop which shall be attached to the partition on one end with gable end bkts and on the other end with metal powder coated frontier leg. Legs - Metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - Main table recta out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 600 mm d and ERU table recta of size 900 mm w x 450 mm d.

Pedestals - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file.

CPU trolley - with castors

KBPT with mousetray - metal

Supply Installation and Assembly of spine and fin based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. FIN: out of 22.5 mm thk panel formed out of blocks which shall be 18 mm thk PLB boards wrapped with laminate at intermediate level. Top block finished in fabric finish. Bottom block is finished in metal Tiles on main spine: Combination of top tiles shall be fabric/split fabric tackable/split white board tile. Bottom tiles - Plain metal. INTERMEDIATE BLOCKS on main spine Intermediate blocks are given in DL + DL finish. Wire Management through main spine- Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Legs - Metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look.

Supply Installation and Assembly of spine and fin based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. FIN: out of 22.5 mm thk panel formed out of blocks which shall be 18 mm thk PLB boards wrapped with laminate at intermediate level. Top block finished in fabric finish. Bottom block is finished in metal Tiles on main spine: Combination of top tiles shall be fabric/split fabric tackable/split white board tile. Bottom tiles - Plain metal. INTERMEDIATE BLOCKS on main spine Intermediate blocks are given in DL + DL finish. Wire Management through main spine- Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Legs - Metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look.Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 600 mm d. Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. his Product should be ISO-9001, ISO- 14001 and ISO-50000 Certified by authentic source.

Pedestals - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file.

CPU trolley - with castors

KBPT with mousetray - metal

Supply Installation and Assembly of Modular conference table made with combination of 2 seater main unit, 2 seater addon unit and head unit. Table should be made of Pre-Laminated twin particle board. "Worksurface : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure : Consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Plastic ABS access flap is provided for easy access to wires and cables. Work top shall be available in various shapes as shown above. Modesty Panel : Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns) Wire Management : An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) should be used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate should be provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component should be fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop." Accessories to be provided for adding functionality to the products. Document Shelf should be made of 1.2mm CRCA MS IS:513 and is epoxy polyester powder coated (DFT 40-60 microns). It is to be used for storing papers and accessing them quickly. HDMI Wire Cover should be made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns). HDMI Holder should be made of 2mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns). The HDMI wire cover along with HDMI holder (part of same packet) to be booked for every provision for HDMI connection as per customer/AV team requirement (except in head and corner module). Name plate to provided to display the name of person and consists of two plates - Inner and Outer plate. They should be made of 1.2 mm Aluminium sheet and 2mm Aluminium sheet respectively. They should be tack welded to each other using Tungsten Inert gas Welding. The Name Plate should be epoxy polyester powder coated (DFT 40-60 microns).

2 SEATER MAIN TABLE_1350*600*730

2 SEATER SHARED TABLE_1350*600*730

MODULAR PLT 2350W ST 2350 X 850 X 730

Accessories ( One packet Contain 8 Qty) Dsk 2 ay Name Plate

Dsk Mod Doc Shelf

Dsk HDMI wire Man

Supply Installation and Assembly of revolving chair. SEAT/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The stitched cover should be made from spacer fabric and leatherette. Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with spacer fabric and leatherette. Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D) BACK SIZE : 45 cm. (W) x 75.5 cm. (D) ARMRESTS The armrest top should be moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk MS E.R.W tube. The armrest height adjustable up to 6.5±0.5cm in 5 steps.The Armrest structure should be powder coated (DFT 40-60 micron). ACTIVE BIO-SYNCHRO mechanism (FU3401/3402): The adjustable tilting mechanism should be designed with the following features: • 360° revolving type. • Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be operated in seating position. • 5-position Tilt limiter giving option of variable tilt angle to the chair. • Seat/back tilting ratio of 1: 2 • The mechanism housing should be made up of HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORTBack Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. TWIN WHEEL CASTOR : 5 Nos. twin wheel castors should be injection moulded in plastic having 6.0±0.1cm wheel Diameter and assembled to pedestal. Overall Dimensions of Chair Seat Height - 44.4-54.4cm. Height - 113.6-131.1cm. Width-76.1 cm and Depth-76.1 cmm This Product should be ISO-9001, ISO- 14001 and ISO-50000 Certified by authentic source.

Supply Installation and Assembly of revolving chair. SEAT/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The stitched cover should be made from spacer fabric and leatherette. Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with spacer fabric and leatherette. Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D) BACK SIZE : 45 cm. (W) x 60.5 cm. (D) ARMRESTS The armrest top should be moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk MS E.R.W tube. The armrest height adjustable up to 6.5±0.5cm in 5 steps.The Armrest structure should be powder coated (DFT 40-60 micron). ACTIVE BIO-SYNCHRO mechanism (FU3401/3402): The adjustable tilting mechanism should be designed with the following features: • 360° revolving type. • Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be operated in seating position. • 5-position Tilt limiter giving option of variable tilt angle to the chair. • Seat/back tilting ratio of 1: 2 • The mechanism housing should be made up of HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORTBack Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. TWIN WHEEL CASTOR : 5 Nos. twin wheel castors should be injection moulded in plastic having 6.0±0.1cm wheel Diameter and assembled to pedestal. Overall Dimensions of Chair Seat Height - 44.4-54.4cm. Height - 98.6-116.1cm. Width-76.1 cm and Depth-76.1 cm This Product should be ISO-9001, ISO- 14001 and ISO-50000 Certified by authentic source.

Supply Installation and Assembly of visitor chair. SEAT/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The stitched cover should be made from spacer fabric and leatherette. Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with spacer fabric and leatherette. Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D) BACK SIZE : 45 cm. (W) x 60.5 cm. (D) VISITOR TUBULAR FRAME: The powder coated (DFT 40-60 micron) tubular frame should be cantilever type & made of 02.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube.The back connected to frame through powder coated (DFT 40-60 micron) high pressure die cast connector piece. Overall Dimensions of Chair Seat Height - 44.8cm. Height - 99.5cm. Width-60.9 cm and Depth-64.3 cm This Product should be ISO-9001, ISO- 14001 and ISO-50000 Certified by authentic source.

Supply Installation and Assembly of MAIN TABLES with ERU attached Pedestal with overall dimension of 1800*2100*750 Primary Work Surface should be Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box should be provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction should be BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension should be 325 MM. Drawers should have a soft closing & anti slam mechanism. Handles should be provided for ease of opening. Pedestals should be provided with lock for security. This Product should be ISO-9001, ISO- 14001 and ISO-50000 Certified by authentic source.

Supply Installation and Assembly of Back unit storage of Dimension 1800W*750H Top Panel-Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Slide Door Unit-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves. Shutters should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters should have a soft closing & anti slam mechanism. Handles should be provided for ease of opening.Storage is provided with lock for security This Product should be ISO-9001, ISO- 14001 and ISO-50000 Certified by authentic source.

Supply installation and Assembly of 6 door locker unit of overall dimension 380mm(W)x450mm(D)x1830mm(H).(Cam Lock) Stackability shall have add - on units that can be stacked width wise to form bank of lockers having common side panel. Locking shall have 10 Lever cam lock with lock lever plus option of hasp arrangement . Material shall be CRCA 0.6 mm thickness . Construction shall be Rigid Knockdown construction , shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Handle/Label holder shall be Aesthetically appealing Snap fit ABS plastic handle . Ventilation shall be attractive punched pattern for ventilation . This Product should be ISO-9001, ISO- 14001 and ISO-50000 Certified by authentic source. Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. This Product should be ISO-9001, ISO- 14001 and ISO-50000 Certified by authentic source.

Supply installation and assembly of visitor chair. SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with synthetic leather and polyurethane foam,BACK SIZE:38.5cm. (W) X 26.0cm. (H). *SEAT SIZE:38.5cm. (W) X 39.5cm. (D). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk._11.S. E.R.W. tube and powder coated (DFT 40-60 microns).

Supply installation and assembly of Single sided wood and steel book rack with combination of main and addon unit. Base Unit 900mm(W)x300mm(D)x1890mm(H). Rigid Knockdown construction . Back panel up to the bottom of third rack for additional rigidity . Racks, Back panel & Skirting : CRCA 0.8 mm thickness . Side panels : 25 mm thick pre laminated particle board (PLB) with laminate on both sides . Stackability shall have add-on units width wiseto form a bank of racks having common side panel . Bottom plus four fixed racks plus five storage levels . Each rack should be provided with stiffener at bottom for strength . Uniformly distributed load capacity per each full shelf is 80 Kg maximum . Rack back stiffener shall be there at the rear side of the racks back stiffener s are provided . These should be to support books on the rear side . Label Holder on each main unit to insert labels for identification . Finish shall be Epoxy polyester powder coated to the thickness of 50 microns. Add On Unit 900mm(W)x300mm(D)x1890mm(H) . Rigid Knockdown construction . Back panel up to the bottom of third rack for additional rigidity . Racks, Back panel & Skirting : CRCA 0.8 mm thickness . Side panels : 25 mm thick pre laminated particle board (PLB) with laminate on both sides . Stackability shall have add-on units width wise to form a bank of racks having common side panel . Bottom plus four fixed racks plus five storage levels . Each rack should be provided with stiffener at bottom for strength . Uniformly distributed load capacity per each full shelf is 80 Kg maximum . Rack back stiffener shall be there at the rear side of the racks back stiffener s are provided . These are to support books on the rear side . Label Holder on each main unit to insert labels for identification . Finish shall be Epoxy polyester powder coated to the thickness of 50 microns .

SINGLE SIDED WOOD & STEEL BOOK RACK BASE UNIT

SINGLE SIDED WOOD & STEEL BOOK RACK ADD ON UNIT

Supply installation and Assembly of chair .Seat- Back : Seat back should be made of blow molded High-density polyethylene andis fixed on the understructure assembly with the help of Stainless steel pop rivets.Seat: Seat should be made of blow molded High-density polyethylene and is fixed on the understructure assembly.Understructure All side metal frames and cross connectors are made from Mild steel ERW tubes ,40 x 20 x 2mm thk(approx. 14 SWG) as per 1S:7138 which are welded togetherThe Welded structures and cross connectors are coated with min 45 micron thickness of epoxy polyester coating. Bag storage tray made of 04 Mild steel rod (as per 15:432) forms a cage at the bottom and is welded to the main understructure. Seat support channel made of 1mm thk Mild steel sheet (as per IS:513) is welded to the understructure for fixing seat. Plastic Caps Plastic Caps made of Polypropylene are provided on the foot rest side tubes and back leg tubes adding more aestheic value to the product. This Product should be ISO-9001, ISO- 14001 and ISO-50000 Certified by authentic source.

Supply installation and assembly of Desk Desk Top panel : Wooden top panel should be made from 18mm thk Pre-laminated twin board with polypropylene injection molded edges.The panels have corners rounded for safety usage. The design of desk-top is such that there should be provision for pen/pencil storage also. The plastic storage tray is made of Polypropylene and is fixed beneath the desktop on the metal understructure. The plastic hinges made of Polypropylene should be fixed beneath the desktop on front side for lifting the top to access the storage below. All side metal frames and cross connectors are made from Mild steel ERW tubes ,40 x 20 x 2mm thk(approx. 14 SWG) as per 15:7138 which are welded together.The Welded structures and cross connectors should be coated with min 45 micron thickness of epoxy polyester coating. Shelf tray and desktop mounting brackets made of 2mm thk Mild steel sheet(as per 15:513) should be welded to the understructure for fixing shelf tray and desktop respectively. Hooks should be provided over the vertical side frames on both sides of the desk for hanging bags/bottles. They should be made from 09 Mild steel rod (As per 15:432) and should be welded to the main understructure. Plastic Caps made of Polypropylene should be provided on the foot rest side tubes and front leg tubes adding more aestheic value to the product. This Product should be ISO-9001, ISO- 14001 and ISO-50000 Certified by authentic source.

Supply, Installation & placement of canteen chair TProviding and supplying plastic shell chair. The seat and back shall be made up of injection moulded high impact strength polypropylene polymer. The understructure shall consist of MS/CRCA round pipe frame having dia. 22.2mm with 1.6mm thick and 35mmX15mm capsule pipe with 1.6mm thick. It should be powder coated to the thickness of 40-60µ DFT. There shall be plastic show provided at the bottom. The overall size of the chair shall be 840mm(H) X 520mm(W) X 530mm(D).The participating brand must have all the prevalent quality & safety related certifications like ISO:9001, ISO:50001, ISO:14001, ISO: 45001 , BIFMA, AIOTA for one or more product, Green Guard certificate for any one product atlest issued by UL of USA.

Supply, installation & placement of Canteen table 1135 Width mm x 1175 Depth mm x 750 Height mm . Top shall be 25 mm thick base material shall be 25 mm MDF board . On top PU painting of minimum 2H hardness with 75% glass as per color chart .Combination color graphics on the centre . Brown Laminate on bottom specially profiled edges for comfort . The Understructure shall be having bend pipe structure of MS powder coated . Pipe dia 38 mm , 2 mm thick and it shall be fitted with top by SS machine screws . Legs shall be of MS powder coated and 38 mm dia. pipe legs are fixed with inderstructure and table top . Glide shall be of Plastic fixed at the understructure to prevent the damage of table top during stacking .

Supply, instllation & placement of 2 seater lounge chair SIDE FRAME ASSEMBLY: The side frame assembly should be fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It should be made of 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick cmx0.16cnn and black powder coated ( DFT 40-60 microns ). The ends should be fitted with ABS moulded end caps. TIE MEMBER: It should be the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members should be used to connect the side frames. The tie-member should be of 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick cm x 0.16cm and black powder coated ( DFT 40-60 microns ). The seat/back assemblies should be mounted on one of the tie-member which has 5.0 ±0.1cm x 5.0 ±0.1 cm x 0.5 ±0.1cm. thk -- 5.5 ±0.1cm Long MS. Std. angles welded to mount the seat and back. SEATREST ASSEMBLY:The seat rest assembly consshould be ts of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45 +1- 2 Kg/m3 with Hardness load 25 ± 2 kgf for 25% compression of the foam. The complete moulded seat rest assembly should be covered with a replaceable fabric upholstery cover *SEAT SIZE: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T) BACKREST ASSEMBLY:The backrest assembly should be flexing type and consshould be ts of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density = 45 +1- 2 Kg/m3 with Hardness load 14 ± 2 kgf for 25% compression of the foam. The complete moulded backrest assembly should be covered with a replaceable fabric upholstery cover. *BACK SIZE: 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T) ADJ. GLIDES: The adj. glide should be injection moulded in black Nylon & fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take cshould be or unleveled floor surface. Overall Dimensions of Chair Seat Height - 43.5 cm. Height - 78.5cm. Width & Depth of Chair as - Width- 113.0 cm and Depth-70.0 cm.

Providing and supplying executive table with an overall size 1350mm X 750mm X 750mm. The top shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. The top shall be supported on CRCA C-frame with 0.9mm thick duly powder coated. The understructure shall consist of MS/CRCA rectangle pipe frame having cross-section area 38mm X 25mm with 1.2mm thick. Fixed top supporting pedestal shall be supplied at one side of the table. The pedestal shall be made up of 0.8mm thick high yield strength CRCA sheet of grade 'D' confirming to IS:513. It should have 3 nos. of drawer i.e. 2 box and 1 filing. It should be operated on ball bearing sliding channel and recessed plastic handle with centralized locking mechanism. The table shall be clad with modesty panel. It should be 18mm thick made up of Pre-laminated particle board.There shall be leveller provided at the bottom. The manufacturer shall have basic quality and safety certifications like ISO-9001:2015, ISO-14001: 2015, ISO-18001:2007, BIFMA Membership & AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Supply, installation and placement of study chair Overall size 900mm X 600mm X 750mm that is to be assembled at site. The worktop shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. The top shall be supported on MS/CRCA rectangle pipe frame having cross-section area 25mm X 25mm with 1.2mm thick. The table understructure shall be supplied with MS pipe having 25mm X 25mm with 1.2mm thick. 1 nos. footstep shall be provided between both side leg with the same size i.e25mm X 25mm with 1.2mm thick. Fixed pedestal unit shall be supplied with 1 nos. of drawer at one side. The drawer shall be central locking mechanism by one single key. The drawer shall be operated with recessed handle. The manufacturer shall have basic quality and safety certifications like ISO-9001:2015, ISO-14001: 2015, ISO-18001:2007, BIFMA Membership & AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Supply, instllation & placement of Double bed Length-2060.0 mm. Width-1915.0 mm. Seating Height-403.0 mm. Total Height-956.0 mm. Internal- Dimensions :- Width.---1836.0 mm. Length -1980.0 mm. Material- M.S. Pipe in 1.2 mm Thickness.Construction :Knockdown construction.Finish :Epoxy powder coated to the thickness of 50 microns (-1-- 10) in Textured Black Colour.

Supply, instllation & placement of matress for double bed 78* 72* 4 Thickness 10 cm & 12.5 cm, Double-layered combination foam mattress comprising bonded and convolution foam, Used Quilt Pu , Bonded, Convoluted Foam, Knitted Fabric.

Supply, instllation & placement of Center table Providing and Placing CoffeeTable in completely KnockDown Condition having overall centre table of 1200mm x 600mm x 450mm Legs: made of 80mm x50mm 2nd class seasoned CP teak wood section duly polished in melamine. Frame: made out 50mm x 40mm teak wood section and top frame 80mm x40mm i/c necessary rebate for resting of 10 mm thick plain clear toughened glass of size 1.08m x 0.48m i/c beveled edge. All teak wood surface shall be finished with high class melamine polish (matt/glossy) polish in required shade on all exposed portions and spirit polish on unexposed faces complete as per approved sample and direction of Engineer-in-charge. All wood shall be second class seasoned CP teak wood. complete and as per direction of Engineer-in charge..The participating brand must have all the prevalent quality & safety related certifications like ISO:9001, ISO:50001, ISO:14001, OHSAS:18001, BIFMA, AIOTA for one or more product, Green Guard certificate for any one product atlest issued by UL of USA.

Providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide back support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used black integral polypropylene arm completely joint with seat. For seating durability the chair shall have synchro tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 120mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700mm and fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycle with 250lbs load. The seat size shall be 465±10 mm(W) X 460±10 mm(D) and back size shall be 480±10 mm(W) X 520±10 mm(H) from seat & overall height = 960±10 mm.

Supply, instllation & placement of 3 seater lounge chair SIDE FRAME ASSEMBLY: The side frame assembly should be fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It should be made of 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick cmx0.16cnn and black powder coated ( DFT 40-60 microns ). The ends should be fitted with ABS moulded end caps. TIE MEMBER: It should be the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members should be used to connect the side frames. The tie-member should be of 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick cm x 0.16cm and black powder coated ( DFT 40-60 microns ). The seat/back assemblies should be mounted on one of the tie-member which has 5.0 ±0.1cm x 5.0 ±0.1 cm x 0.5 ±0.1cm. thk -- 5.5 ±0.1cm Long MS. Std. angles welded to mount the seat and back. SEATREST ASSEMBLY:The seat rest assembly consshould be ts of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45 +1- 2 Kg/m3 with Hardness load 25 ± 2 kgf for 25% compression of the foam. The complete moulded seat rest assembly should be covered with a replaceable fabric upholstery cover *SEAT SIZE: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T) BACKREST ASSEMBLY:The backrest assembly should be flexing type and consshould be ts of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density = 45 +1- 2 Kg/m3 with Hardness load 14 ± 2 kgf for 25% compression of the foam. The complete moulded backrest assembly should be covered with a replaceable fabric upholstery cover. *BACK SIZE: 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T) ADJ. GLIDES: The adj. glide should be injection moulded in black Nylon & fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take cshould be or unleveled floor surface. Overall Dimensions of Chair Seat Height - 43.5 cm. Height - 78.5cm. Width & Depth of Chair as - Width- 164.0cm and Depth-70.0 cm.

GEEKEN SEATING COLLECTION PVT LTD

Unison Furniture Palace