SPL REPAIR TO KITCHEN, TOILET AND BATHROOM FOR 26 DUS AT TARAPORE OFFICER ENCLAVE UNDER GE (SOUTH) DELHI CANTT-10

Amount

Taking down cement or cement lime plaster, any description, on brick or stone walls, concrete surface etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by engineer-in-charge.

M & L for 15mm thick rendering with ready mix plaster on brick /concrete of wall finished fair even and smooth wihout using extra cement, complete all as specified and directed.

M & L for 5 mm thick CM (1:3) rendering with ready mix plaster as in ceiling and finished fair even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying 1 to 2 mm thick wall care putty on whole surfaces including grinding with sand paper and levelling of surface and applying two coat of oil bound distemper on white or tinted over existing prepared putty base surface, complete all as specified and directed by engineer -in-charge. Note :- (a) All work shall be done mechanically through authorised applicator only (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 Days from start date of the said finishing work. (c) The contractor shall provide application testing and certification of finishes by paint manufacturing firm/their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for preparation of newly plasered surfaces of walls and applying two coat of super quality weather proof exterior emulsion paint over and including one coat of primer from the same manufacturer on external wall / ceiling surfaces including a coat of 3mm thick wall care putty to achieve smooth surface, complete all as specified and directed by engineer-in-charge. Note :- (a) All work shall be done mechanically through authorised applicator only (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 Days from start date of the said finishing work. (c) The contractor shall provide application testing and certification of finishes by paint manufacturing firm/their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for preparation of newly plasered surfaces of ceiling and applying three coat of white wash, complete all as specified and directed by engineer-in-charge.

M&L for complete removal of existing treatment from internal surfaces of wall by electrically operated grinder, washing and filling of holes with filler material and applying 2 to 3 mm thick wall care putty in two layers on whole wall surface including grinding with sand paper and levelling the surface and than applying two coat of oil bound distemper on white or tinted surface over existing prepared putty based surface, complete all as specified and directed by engineer-in-charge. Note :- (a) All work shall be done mechanically through authorised applicator only (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 Days from start date of the said finishing work. (c) The contractor shall provide application testing and certification of finishes by paint manufacturing firm/their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for complete removal of existing treatment from External surfaces of wall and applying two coat of super quality weather proof exterior emulsion paint over and including one coat of primer from the same manufacturer on external wall / ceiling surfaces including a coat of 3mm thick wall care putty to achieve smooth surface, complete all as specified and directed by engineer-in-charge. Note :- (a) All work shall be done mechanically through authorised applicator only (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 Days from start date of the said finishing work. (c) The contractor shall provide application testing and certification of finishes by paint manufacturing firm/their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for preparation of old surface of ceiling and applying one coats of white wash, complete all as specified and directed by engineer-in-charge.

M&L for Preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted surfaces of steel of any description over 10cm width or grith and applying one coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for Vitrified Ceramic tiles double charged (light shade), 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for Vitrified Ceramic tiles double charged (light shade), 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in skirting jointed in neat cement slurry and pointed in white or coloured cement to match and including backing coat of mortar 10 mm thick in CM 1:4 complete all as specified and directed.”

M & L for 7 to 8 mm thick Glazed Ceramic coloured tiles in vertical surface area exc. 0.11 Sqm each but 0.18 Sqm each set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10mm thick backing coat of cement mortar (1:4), complete all as specified and directed

M&L Non Skid ceramic tiles 8 to 10mm thick (square/rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in CM 1:6 complete all as specified and directed.

S&F in repairs,sink mixer for mixing valve 15mm dia wall mounted with 165mm long swivel spout, connecting legs and wall flanges, Hot and Cold CP brass fancy type including joints to steel pipe or unions , including fittings, complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Product Code – FLP-5309PM), Cera (Product Code : F1017501), Hindware (Product Code – F280020).

S&F in repairs, Single or double leaver central hole mixer for mixing with 450mm braided connection pipe 15mm dia, Hot and Cold CP brass fancy including joints to steel pipe or unions for centre hole wash hand basin , including fittings, complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Product Code – FLP-5001BPM), Cera (Product Code : F1017451), Hindware (Product Code – F280010).

S&F in repairs, wall mixer with bend pipe for overhead shower mixing valve Hot and Cold water Screwed Down for iron pipe 15mm dia CP brass fancy type including joints to steel pipe or unions , including fittings for, complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Product Code – FLP-5273PM), Cera (Product Code : F1017401), Hindware (Product Code – F280018).

S&F in repairs two way CP brass bib cock15mm dia with single handle and wall flange complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Product Code – FLP-5041PM), Cera (Product Code : F1017211), Hindware (Product Code – F280003).

S&F in repairs, CP brass health faucet alongwith 1.00 to 1.50 meter good quality SS flexible connection pipe suitable for 15mm bore pipe, complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Product Code – ALD-CHR-577), Cera (Product Code : F8030111AB), Hindware (Product Code - F160195CP).

S&F in repairs, Brass chromium plated shower rose 125mm size with arm, complete all as specified and directed by Engineer-in-Charge.Make : Jaquar (Product Code – OHS-CHR-1663), Cera (Product Code : F7020305), Hindware (Product Code - F160119CP).

S&F in repair brass chromium plated towel rack of size 600mm x 240mm x 220mm fixed with fixed with suitable screw complete all as specified and as directed. (Pattern as approved by Engineer-in-Cahrage) Make : Jaquar (Product Code – AQN-SSF-7781B), Cera (Product Code : F5001101), Hindware (Product Code - F580008CP).

S&F in repair Vitreous china wash down water closet pan (pedestal pattern) ‘P’ or ‘S’ trap , white/ off white, plastic WC seat cover fo white/ off white closed pattern with flat bottom end cover and mild steel CP hinging device including tail piece 100 mm dia PVC(SWR) pipe complete all as specified and directed by Engineer-in-Charge

S&F in repairs, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets of 10 litre capacity, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, PVC waste pipe 32mm bore, 65cm long plain/ corrugated including suitable adopter, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, stainless steel grating dome 125 mm dia of best quality, complete all as specified and directed by Engineer-in-Charge.

S/F in repair brass chromium plated bottle traps for wash basins with inlet and outle screwed for pipe or connections including necessary packing, union and cap and fixed 40mm-270 gms)

S&F in repair Vitrous china wash hand basin white, ovel type over counter Wash hand basin size 550x 420mm, including necessary waste pipe and coupling, Fixing in Granite counter sunk complete all as specified and as directed.

Dismantling of stone slab and tiles laid bedded and pointed in any mortar of any discription or thickness in floors

S&F in repair of granite (of any type) tiles 12 mm thick machine cut over 15mm thick CM (1:4), bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone duly grinded and polished complete as in cooking plateform, window cill etc

S&F for 16-18 mm thick Granite slabs (of any type any colour) work (table rubbed and polished) as in steps, jambs, pillars, window cill, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble laid over 15mm thick screed bed in CM 1:4..

Rounding to edges of stone slabs one edge such as in steps cooking platform and other similar situations

M&L for Stainless steel (SS) 316 grade any section as like tee, angle, hollow pipe and square/rectangular tube, flat plates etc as in cupboard/kitchen cabinets frame work fixed with necessary fittings SS screws, nut, bolts, fastners, washers etc (as approved by Engr-in-charge) including necessary cutting drilling profile, cutting of components to required length/width and shapes/profile and smooth grinding/maching of edges/ faces/all welding joints including buffing and polishing complete all as specified and as directed

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe.290.Gde-E-165, complete all as specified and directed by engineer-in-charge.

Dismantling boarding, any description, fixed in any position with nails, complete all as specified and directed by engineer-in-charge.

M&L for 18mm thick wood plastic composites (WPC) board, fixed with screws as in cupboard/ wardrobe/ almirah shutter/kitchen cabinet boxes, including PVC beading all around edges of shutter and all necessary fittings and fixtures like nickle plated clip hinges & knobs (01 Nos knobs & 02 Nos clip hinges for each panel) etc complete all as specified and directed. Note: (a) Pattern & design of WPC board to be decided by GE. (b) The unit rate are deemed to be included for Items like, magnetic Catcher (01 No for each panel), clip hinges (02 Nos for each panel), knob (01 No for each panel) to be included in quoted rate

S&F in Repair U shaped double stainless steel 600mm long channel of size 10 mmx 20mmx 1.50 mm fixed to wooden frame including suitable rail / rollers etc complete all as specified and directed

S&F in repair of 40 mm dia cupboard knobs fixed with nut, screw and washer of brass polished

S&F in repair stainless steel wire cloth, 0.63mm nominal dia or wire and sqm average width or aperature 1.40mm, fixed with tinned tacks or galvanised wire staples to wooden or steel doors/steel or aluminum windows including necessary screws/nuts/bolts/flat iron strip to hold wire cloth, complete all as specified and directed by engineer-in-charge

S&F in repairs for stainless steel plate rack made of 1mm thick stainless steel sheet of size 910 mm x 460 mm x 210mm consisting of 3 shelf for bowls and one shelf for keeping six nos of big utensil and seven nos of small utensils divided by 10mm dia stainless steel hollow pipe @ 60mm centre to centre, complete all as specified and directed by Engineer-in-Charge.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm.

S&F for rotational moulded polythylene water storage tanks 250 litres capacity (Rectangular with closed top) hoisted and fixed in position complete all as specified in SSR-I including brass valve high pressure with polythne float and fly nut complete, screwd for iron pipe or brass ferrule size 25 mm bore including dismantling of water tanks of any type/pattern and removing from site complete all as specified and as directed.

S&F in repair 15 mm angle valve / stop cock chromium plated, cast copper alloy screwed down high pressure fancy type, chromium plated with long shank and cup (concealed type) screwed for both ends for iron or for unions complete all as specified and as directed.

S&F in repair toilet paper holder of brass chromium plated fixed to walls with CP brass screws, complete all as specified and as directed.

Taking up or down steel tubing and connections, 15 mm bore of pipe, complete all as specified and directed by engineer-in-charge.

All as per item no -47- here in before but 20 mm bore of pipe, complete all as specified and directed by engineer-in-charge.

M&L supplying and fixing of 15 mm bore UPVC pipes SDR 11 & plain CPVC SCH-40 fitting on walls /ceiling or laying in floors including all fitting such as ( brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded adaptor etc) union ,ball valves, flange and tank adaptor complete all specified and directed by Engr-in-Charge

All as per item no -49- here in before but 20 mm bore of pipe, complete all as specified and directed by engineer-in-charge.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames), complete all as specified and directed by engineer-in-charge.

S&F factory made moulded solid PVC chowkhat/ door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with 19 mm x 19mm MS square tube of 19 gauge including rubber gasket, PVC fastners, screws, brackets, and shown on drawing as per SSR part-II (2010), complete all as specified and directed by engineer-in-charge.

S&F factory made moulded solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tube for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strips of 20 mm with stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail , lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail , panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement , supplying and fixing in the frame at the site as per specification & drawing . on page no 161 of SSR part-II (2010), complete all as specified and directed by engineer-in-charge.

Taking down shutters with chowkhats any description exc 1.00 sqm but not exc 2.00 Sqm each and refixing the chowkhaks with shutter in same opening after easing and adjusting/repairing complete as directed by Engineer incharge.

S&F stainless steel butt hinges, size 150 mm complete, complete all as specified and directed by engineer-in-charge.

S&F aluminium anodised barrel tower bolts, 150 mm long of extruded section and fixed, complete all as specified and directed by engineer-in-charge.

S&F aluminium handles, 150 mm size, fabricated type, complete all as specified and directed by engineer-in-charge.

&F Stainless Steel chromium plated peg set of five or more hooks fixing with wall, complete all as specified and directed by engineer-in-charge

Demolition of cement concrete of any description and in any position not otherwise specifically provided for including removal the rubbish/demolished material outside defence land, complete all as specified and as directed.

Material and labour for water proofing treatment of sunken floor of WCs, bathroom etc. by applying of the following specifications :- (i) Cleaning of sunken floor surface with mechanical means i.e. wire brush/air blower etc. and remove all loose/unsound material, dirt, dust, etc. (ii) Applying cement slurry mixed with acrylic based polymer modified cementitious composite compound coating Hydroproof Xtra of FOSROC/Equivalent of Dr Fixit of Pidilite Industries Ltd in the ratio of 1:2:4 (One part of acrylic polymer : Two part of water and four part of cement). (iii) First layer of cement slurry @ 0.444 Kg/Sqm mixed with acrylic based modified cementious composite compound @ 0.222 Litre/Sqm and allow it to air dry for 04 hours. (iv) Second layer of cement slurry @ 0.222 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.111 Litre/Sqm and allow it to air dry for 04 hours followed with water curing for 48 hours. (v) 200 micron thick polythene film shall be pasted with help of adhesives over treatment. Note :- Joints of WC/Trap/Soil waste shall be properly sealed with sealing compound. Testing of all traps and joint and sunken slab shall be done as per IS-1742 before filling and tiling work.

Material and labour for plain cement concrete 1:5:10 type E-2 (using 40mm graded broken bricks aggregate) as in foundation, filling and mass concrete, complete all as specified and as directed.

Material and labour for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in levelling courses laid and compacted in slope in floor complete all as specified and as directed.

S&F 06 mm thick toughened glass rectangular glass shelf of size 600mm x 125mm with stainless steel railing around 03 sides of glass including necessary fixing to wall with brass/SS screws, complete all as specified and directed by engineer-in-charge.”

Taking down carefully Copper point wiring (light/fan/bell/socket /power) with complete fittings such as steel terminal boxes, switches, ceiling roses, pendents, regulators, sockets etc and removing the material including making good the distrubed surfaces of the wall flooring ceiling etc to match the existing surface all as specified and directed by Engr-in-Charge.

M&L for concealed point wiring complete with stranded copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable drawn through concealed PVC conduit and including replacement of unserviceable pressed steel terminal boxes with Modular steel terminal boxes factory made including white cover modular plate with frame suitable for modular switches, modular sockets, modular fan regulators etc of required size complete including 1.5 sqmm copper cable earth continuity wire to common earth and connected to earth dolly complete all as specified for One light/Fan/Bell point controlled by one 5 Amp switch one way using cable (1.5 Sq mm for phase and neutral and 1.5 sqmm for earthing) . Note :- The rate is inclusive cutting/chasing and making good disturbed surface with CM 1:3 and same surface finishs with the adjoining surface of disturbed area with OBD/Colour wash/white wash complete.

All as per item No 65 above but 5 Amp socket outlet on same board.

All as per item No 65 above One socket outlet 5 Amps on independent board.

All as Item No 65 above but for one socket outlet 5/15 Amps on Independent board with cables 2.5 sqmm size for phase and neutral and 2.5 Sqmm for earthing complete.

Taking down carefully complete fittings such as steel terminal boxes, switches, ceiling roses, pendents, regulators, sockets etc and removing the material including making good the distrubed surfaces of the wall flooring ceiling etc to match the existing surface all as specified and directed by Engr-in-Charge.

S&F switch modular type, 1 way 6A, 1module.

S&F switch, Modular switch 2 way 6A, 1 module.

S&F Modular Socket, 6A - 2/3 pin 2 module

S&F switch modular type 1way 16A, 1module

S&F Socket 6A/16A - 2/3 pin combined 2 module.

Note - for item No.65 to 68 including frame of suitable size with replacement of existing pressed steel terminal box with suitable type of new modular junction box.

S & F in replacement ,Decorative wall light mounting suitable for LED Lamp upto 15 Watt complete with all connections all as specified and directed.

Taking down Wall mounted LED Integrated Batten 20 Watt - 4Ft & 10W 2 Ft and wall Light refixing the same after B/R work plaster etc complte including necessary connections of incoming and out going cables. as specified and directed by Engr-in-charge.

S&F in replacement Wall mounted LED Integrated Batten 20 Watt - 4Ft White, indoor decorative PVC extruded LED battern complete.

S&F in replacement Wall mounted LED Integrated Batten 10 Watt-2 Ft White, indoor decorative PVC extruded LED batten, complete.

S&F Modular AC Box with socket and MCB SP 25 Amp complete with Metal box , white colour plate and frame complete in replacement of sheet metal enclosures as per site requirement , complete all as specified and directed.

S&F in replacement of lamp holder Angle/ Batten type bakelite insulated body with back plate all as specified and directed.

S&F ceiling rose surface Bakelite 65x25mm two to three terminals complete all as specified.

Taking Down of geyser and keeping in safe custody and refixing it back after completion of point wiringand Painting Work complete all as specified and directed at site.

Taking Down of Exhaust Fan Complete including louver and refixing it back after all B/R work like plaster painting etc completion of point wiring and Painting Work complete all as specified and directed at site.

Re-Fixing of exhaust fan and connecting up including electrical correction from ceiling rose/connector to fan complete all as specified and dierected by Engr in charge.

Taking Down of wall mounted fan of Kitchen and refixing it back after completion of B/R cement & painting Work complete all as specified and directed at site.

P R Constructions (BID ID -3172097)

M/S Chhavi Constructions Co (BID ID -3167204)

M/S Parmod Johar (BID ID -3166354)

A R construction (BID ID -3166208)

Vipul Construction (BID ID -3167122)

BEHAL TRADERS (BID ID -3167038)