NIT No 15/2021-22/EE/TCAG

Amount

Credit for:

Unserviciable Brass Bib/stop cocks/pillar tap

Gun metal gate valve with C.I wheel 25 mm dia

Low level PVC flush tanks (10 litres)

Credit to the work un-serviceable material recovered from dismantling/demolishing work:

a)Brass/CP brass bib cock, stop cock and other brass material.

Cutting floor of sunken portion (toilet/bath room) upto required length and width for fixing bend for w.c. pan/trap and associated soil/waste pipe and making hole in adjacent brick wall for outlet and repairing same after fixing w.c. pan/trap including cost of required c.c./plaster etc. complete as per direction of the Engineer-in-charge.

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) :

Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.

Providing and fixing sheet covering over the bottom of doors with screws as per design

Aluminium fluted strips 3.15 mm thick.

150 mm wide

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

12 mm cement plaster of mix :

1:6 (1 cement: 6 fine sand)

20 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) finished with a top layer 6mm thick cement plaster 1:6 (1 cement: 6 fine sand).

6 mm cement plaster of mix :

1:3 (1 cement: 3 fine sand)

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

Two or more coats.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade :

One or more coats on old work.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work.

French spirit polishing :

One or more coats on old work.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground , all complete as per directions of Engineer-In-Charge.

With cement mortar 1:4 (1 cement : 4 fine sand).

Raking out joints in lime or cement mortar and preparing the surface for re-pointing or replastering including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge.

Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for flat tile bricks on top of mud phaska :

With F.P.S. brick tiles

Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank, including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba, all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account)

Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial de-silting of manholes and de-chocking of sewer lines. De-chocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150mm dia upto 300mm dia for all depth.

Providing & fixing White vitreous china water closet squatting pan (Indian type) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge.

Long pattern W.C Pan of size 580x440 mm

Supply of Carpenter for miscelleaneous work at site of work

Supply of beldar for miscelleaneous work at site of work

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

10 litre capacity - White

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete :

White solid plastic seat with lid

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings :

Flat back wash basin of size 630x450 mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

32 mm dia

Providing and fixing on wall face unplasticised Rigid PVC SWR grade Soil, waste, vent pipes conforming to IS : 13592 Type A, including jointing with seal ring IS : 5382, leaving 10 mm gap for thermal expansion,conforming to IS : 13592: Single socketed pipes.

75 mm diametre

Providing and fixing low level cistern internal fitting kit (syphon) including checking for proper working etc. complete.

Providing and fixing 15 mm CP brass pillar tap IS:8931 of approved quality as per direction of the Engineer-in-charge.

Weeding out vegetation growth embedding from the bulding at different locations and at varying height from 3mtr to 10mtr from ground,plucking, pulling out roots embedded deep inside the building, pouring acid to prevent further gowth of plants complete etc., as per the directions of Engineer-in-charge.

Providing and fixing PVC tank lid to the overhead tank with necessary screws, nails, bolts & nuts complete etc.,as per the directions of Engineer-in-charge.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti- microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threadedpolypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases andmaking good the same including testing of joints complete as per direction of Engineer-in-Charge.Concealed work,including cutting chases and making good the wall etc.

PN - 16 Pipe, 20mm OD (SDR-7.4)

PN - 16 Pipe, 25mm OD (SDR-7.4)

PN - 16 Pipe, 32mm OD (SDR-7.4)

Providing and fixing uplasticised PVC connection pipe with brass unions :

30 cm length

15 mm nominal bore

45 cm length

15 mm nominal bore

Providing and fixing Centeral hole C.P. brass basin mixer of Jaquar make (Model :CON-CHR-167KNB ) for hot and cold water mixing with a provision for shower control including necessary fittings as directed.

15mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

150 mm diameter

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required :

15 mm nominal bore.

20 mm nominal bore.

25 mm nominal bore.

32 mm nominal bore.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:

15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 :

15mm nominal bore

Providing and fixing PTMT grating of approved quality and colour.

Circular type.

100 mm nominal dia.

Changing of washer of Bibcock/stopcock/ pillar cock including all labour etc. complete.

Arresting leakage through GI pipe by cutting and dismantaling upto length of 6.00 Metre and fixing the same includinmg providing and fixing G.I. Union , cutting and threading the pipe and making long screws, etc complete

15 mm nominal bore.

20 mm nominal bore.

25 mm nominal bore.

Replacing brass spindle of pillar tap/bib cock etc. of approved quality in order to make the tap in good working order complete as per direction of the Engineer-in-charge.

Cleaning of all roof top including mumty of straircase, khurra, under of water tank etc. by removing silt, fungi etc. and disposal of malba to an authorised municiapl dump outside of compound as per direction of the Engineer-in-Charge.

Cleaning of chocked water supply GI pipe line by pressure machine for proper supply of water i/c opening and refixing of bends, socket etc whichever necessary all complete as per direction of Engineer-in-Charge.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

1.0 mm thick.

Providing and fixing plain lining with necessary screws/nuts & bolts/nails including a coat of approved primer on one face and fixed on wooden /steel frame work, complete as per direction of Engineer-in-charge. (Frame work shall be paid for separately)

12mm thick commercial ply conforming to IS : 1328 BWR type.

M/s Sai Nath Construction