SPECIAL REPAIR TO BLDG NO P 183 01 TO 04 AT BHAGAT ENCLAVE AT SRI GANGANAGAR MIL STN

Amount

Dismantling of brick tiles or terracing tiles single layer on roof including also taking down existing APP membrane & disposal of retrieved material upto a distance n.exc 100m away from site all as specified and directed by Engineer-in-Charge.

Demolition of mud in roof, any thickness including plastering and leaping (where full thickness removed or only a part there of disposal off rubbish upto a distance n.exc 100m all as specified and directed by Engineer-in-Charge.

Providing and applying waterproofing work with polyester reinforced APP membrane sheet of thickness 3mm ,wt not less then 3 kg/sqm by Mechanically clean the RCC slab and wall with wire brush / coir brush to free from all loose materials like dust, dirt etc / coving of 50x50 mm at all horizontal and vertical joints to avoid right angle turning with polymer based mortar. Apply one coat of solvent based bitumen primer on cleaned & leveled surface @ 3-5 Sqm / ltr per coat then apply tack coat of 1.20 kg/sqm . Unroll the roll after application of primer. Align the roll correctly & re-roll it in alignment before torching. Use gas burner to heat substrate and underside to softening points. When the embossing disappers, roll forward and press fimly against substrate to bond from the lower end towards the higher end. Keep overlap margin for minimum 100mm. Heat both the overlaps and use round tipped trowel to seal overlap. Excess compound shold be smoothened and pressed into seam using hot trowel complete all as specified and directed by Engineer - in - Charge.

M&L 40mm thick brick tiles bedded in 15 mm thick cement mortar (1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and directed by Engineer in charge.

M&L Cement concrete tiles 25cm x 25xcm x 22 mm thick,with gray cement and no pigment machine pressed; set, jointed and pointed in neat cement slurry over and including cement 15 mm thick scereed in CM (1:6) with and including liquid water proofing compund as per manufactures, specifications, as in roof and floor tiles complete all as specified and directed

M&L for cement concerete 1:3:6, type C2 (40 mm graded stone aggregate) as in filling and mass concerete in roof padding etc complete all as specified and dirceted by Engineer-In-Charge.

M&L PCC 1:2:4, type B1, using 20 mm graded stone aggregate as in roof kerbs / benching / coved fillets etc rounded or chamfered on edges, complete, all as directed.

Demolition of brick work built in cement mortar or RCC work in parapet including all , pillars etc and precast concrete articles complete all as specified and dirceted by Engineer-In-Charge.

M&L brick work with sub class B bricks straight or curved on plan exceeding 6 mtr mean radius in cm 1:6 etc.complete all as specified and directed by Engineer - in - Charge.

M&L brick work using old bricks retrived from demolition of bricks straight or curved on plan exceeding 6 mtr mean radius in cm 1:6 etc.complete all as specified and directed by Engineer - in - Charge.

M&L half brick work with sub class B bricks straight or curved on plan exceeding 6 mtr mean radius in cm 1:6 etc.complete all as specified and directed by Engineer - in - Charge.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair face of brick work of walls, mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified. Note : - Supply only water proofing compound shall be measured and paid separately under respective item of BOQ.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

Supply only integral water proofing compound, ISI Marked.

M&L for prepration of New plastered Internal wall surface complete applying the following :- (a) M&L wall care putty in two coats on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) M&L two coats of interior acrylic emulsion over a coat of priming by using Airless spray / Roller over complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-charge in case of places where using of Mechanical equiment is not possible.

M&L for prepration of New external plastered wall surface complete all as specified complete all as specified and applying the following :- (a) Applying wall care putty in two coats on wall surface and smoothening the surface with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified (b) Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed by engineer in charge

M&L for preparation of newly plastered surface of ceiling and applying two coats of oil bound distmper over a coat of primer etc complete all as specified and directed by Enginer-in-Charge.

M&L for complete removal of existing treatment including filling depression of scraped surface with wall care putty in two coats on old internal wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as specified and directed complete and applying two coats of interior acrylic emulsion of approved tint over a coat of primer on old prepared surface by using Airless spray / Roller over complete all as specified & directed. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible

M&L for complete removal of existing surface finishes of ceiling and applying two coats of oil bound distemper on old ceiling surfaces etc complete all as specified.

M&L for complete removal of existing treatment including filling depression of scraped surface with wall putty two coats on Old external wall surfaces of any desciption , preparation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology , complete all as specified and applying the following :- (a) M&L two coats of exterior acylic emulsion by using Airless spray / Roller over and incl a coat of acrylic emulsion external primer complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of where using of Mechanical equiment are not posiible

M&L for preparation of old surface including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and making surface even and smooth and complete and then appplying two coats of Oil Bound Distemper on old decorated plastered or un-plastered surfaces of walls etc all as specified & directed by Engineer-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust and Brushing neat cement slurry with 3.0kg of cement per sq. metre, etc. all as specified & as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, all as directed.

M & L double charged Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm & n exceeding 1 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and directed.

M & L double charged Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm & n exceeding 1 Sqm, in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement in vertical surface including 10mm thick screed bed in cement & sand mortar 1:3 complete all as specified and directed.

M&L for non skid ceramic edge cut tiles (coloured) 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4, complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 600x300x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering (to received the tile) in cement & sand mortar 1:4, complete all as specified and as directed.

M&L for 75 mm thick PCC 1:3:6, type C2, using 40 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3) complete all as specified and directed by engineer in charge

M&L for 25mm thick PCC 1:2:4, type B0, using 12.5mm graded crushed stone aggregate as in flooring finished fair & even complete all as specified & as directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness below and above ground level complete all as specified and directed by Engineer-in-Charge.

Taking up or down GI tubing 15 mm bore pipe including cleaning for re-fixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Fixing only 15 mm dia, old steel tubing and connections in new or old possition (wall,ceiling and floors etc) complete all as specified and directed by Engineer-in-Charge. Note : GI pipe shall be use from item No 33.00 of BPQ.

S&F GI tubing 15 mm bore medium grade galvanise with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified.

Taking up or down GI tubing 20 mm bore pipe including cleaning for re-fixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Fixing only 20 mm dia ,old steel tubing and connections in new or old possition (wall,ceiling and floors etc) complete all as specified and directed by Engineer-in-Charge. Note : GI pipe shall be use from item No 33.00 of BPQ.

S&F GI tubing 20 mm bore medium grade galvanise with all fitting and fixed to walls & ceilings or laid in floors complete all as specified.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic WC seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device, complete all as specified & as directed.

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F in repairs vitreous china wash hand basin with pedestal, white, bowl of size 510mm x 420mmx 180mm & pedestal long 175mm x 185mm x 715mm including a pair of cast iron brackets embedded in PCC 1:3:6, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F in repair stainless steel grating 125mm dia with waste hole (Minimium weight 40 grams)

S&F in repair stainless steel grating 100mm dia without hole (Minimium weight 25 grams)

S&F in replacement PVC connection 450 mm long suitable for 15 mm bore GI pipe including CP brass nuts on both sidescomplete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15mm bore Long body bib tap, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

S&F in repair CP angle valve for 15 mm bore pipe with capstan head long screwedshank including cp cover plate fancy type fixed complete all as specified and directed.

S&F in repair 15mm bore concealed type, stop valve cast copper alloy screwed down high pressure with capstan head and cup, screwed both ends for iron pipe or for union all as specified.

S&F central hole wash basin mixer 15mm bore brass without polp up waste with 10mm dia 450mm long copper pipes.

S&F L Band CP wall mixer for bath and shower system, complete all as specified and directed.

S&F in repairs, Brass CP Kitchen Mixer for mixing hot and cold water screwed down for iron pipe and fied complete all as specified and directed by Engineer - in - Charge.

S&F in repair and shower health faucet to EWC ,CP brass with minimum 1000mm long CP flexible pipe, connection etc, complete all as directed.

S&F in repair toilet paper holder, brass chromium plated fixed to walls with chromium plated (CP) brass screws complete all as directed.

S&F CP brass soap dish of fancy type complete all as specified and directed by Engineer-in-Charge.

S&F glass corner self assembly, fancy type, made of 5 mm thick sheet toughened glass of size 250x250mm, fixed with CP brackets, complete, all as specified and directed.

S&F 5 mm thick and 450 mm long, width 150mm glass shelves fancy type and fixed over CP brass brackets all as specified and directed by Engineer-in-charge.

S&F in repairs CP brass towel rack, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified.

S&F 40mm bore PVC low density (LDPE) pipe of pressure 6kg/Cm2 fixed to wall or laid in floor complete all as specified and directed by Engineer-in-Charge.

S & F in repair bottle trap of PTMT 32mm dia having minimum water seal of 25mm (min weight 260gm) complete all as specified and directed by Engineer-in-charge.

S&F in repairs self clean round ABS shower rose of 200 mm size Square/round with swivel joint including fixing with long shower arm of size 600mm long to steel pipe of 15mm bore or union complete all as specified.

S&F in repairs cabinet of PTMT with looking mirror of size 350x555mm complete all as specified and directed by Engineer-in-charge.

S&F in repair double bowl stainless steel sink made of 1mm thick sheet for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 940mm x 455 x 250 mm with including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4, type B0, complete, including taking down old unserviceable sink.

S & F in repairs stainless steel Kitchen plate rack of overall minimum size 900mm x 750 mm x 250mm deep, with partitions for small/large plates etc made out of stainless steel 0.80 mm thick sheet fixed with rawl plug and CP steel screws complete complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stainless steel curtain rod 25 mm dia (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm c/c) complete all as specified and directed by Engr-in-charge.

M&L for 18 to 20 mm thick Granite (of any type) slab of approved shade as in kitchen platform,steps,jambs,pillars,window cills,cooking plateforms etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) over & including 25mm thick screed bed (bedding layer) in CM 1:4 complete all as specified & directed.

M&L for 18 to 20 mm thick Granite (of any type) slab of approved shade as in riser, skirting etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) over & including 15mm thick in CM 1:4 complete all as specified & directed.

Dismantling PVC water tank/RCC tank and removing for capacity exceedin 250 litres & not exceeding 500 litres etc, complete all as specified and directed by Engineer-in-Charge.

Dismantling PVC water tank/RCC tank of water tanks of capacity exc 500 Ltr & n.exc 1000 Ltr and removing from site all as specified.

S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks Triple layered White coloured (cylindrical, vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete all as specified and directed.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks Triple layered White coloured (cylindrical, vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete all as specified and directed.

S&F in repair 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe, all as specified.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20 mm bore, all as specified and as approved by GE/Engineer-in-Charge.

M&L in repair block board, 18/19 mm thick, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame work as in cup board shutter/shelves/cabinet etc, complete all as specified and directed.

M&L for 0.90mm thick decorative laminates 'Mica type 1 of surface finished,colour and pattern as approved, fixed with adhesive as per makers instructions.

S&F door viewer vide angle brass with glass cap 14 mm dia complete all as specified and directed by Engineer-n-charge.

M&L mortice lock with with brass body 100 mm long complete all as specified and directed.

S&F 25 mm size magnetic catches with Plastic body and striking plate including letting in and fixed complete all as specified and directed by Engineer-in-Charge.

S&F continuous (piano) hinges 20mm & 12 mm width of flap, mild steel bright finish or electro galvanised fixed with CP steel screws complete all as specified and directed by Engineer-in-Charge.

M &L for providing Modular Kitchen Cabinet/cup board with shutters in required sizes & shape at site made out of 18 mm thick one side decorative laminate and other side balancing lamination sheet consisting of carcass 18 mm thick PVC sheet & PVC sheet with all required brackets SS screws e.t.c. The panels shall be fabricated using adhesive and screws where ever required . All the edges shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish as per manufacturer instructions and as directed by Engineer-in-Charge.

S&F Cup Saucers fabricated with stainless steel section (SS-304), best quality of size 420 mm x 500 mm x 100mm for different use such as placing plain plate /cutlery etc fixed in position complete all as specified and directed by Engr In charge

S&F Cutlery set & Dustbin fabricated with stainless steel section (SS-304), best quality of size 420 mm x 500 mm x 150 mm for different use such as placing cup & saucer etc fixed in position complete all as specified and directed by Engr In charge

S & F Stainless steel fancy type 200 mm handle complete all as specified and directed by Engr In charge.

S & F Telescopic Ball bearing Channel chromium plated of size 500 mm (when closed) fix to kitchen basket complete all as specified and directed by Engr In charge.

S& F Auto Closing Concealed Hinges for Half Overlay Doors with 95 Degree Opening Angle complete all as specified and directed by Engr in charge.

Supply & fixing hasp and staple of size 75 mm aluminium anodized safety type with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but n.exc 4 sqm each, complete all as specified & directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area not exc 1.5 sqm each complete all as specified & directed.

Taking down window, ventilator with shutter (without taking off shutter from the frame) and area not exc 1.5 sqm each complete all as specified & directed.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws all as directed.

S&F Pressed steel frames of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, (thickness of sheet shall be 1.25mm) and making good the wall with plaster in CM 1:6 complete all as specified.

S&F for pressed steel frames of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs hinges, locks strike plate etc, (thickness of sheet shall be 1.25mm) and making good the wall with plaster in CM 1:6 complete all as specified.

M&L PCC 1:3:6, type C-1, using 20 mm graded stone aggregate for filling in back of pressed steel door frame/ chowkhat and fixing of bed block of hold fast etc complete all as specified and as directed.

S&F 2nd class HW factory made Plain, framed, pannelled shutters 35 mm thick (two panels), with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I) Kiln seasoned and chemically pressure treated all as specified and directed.

S&F 2nd class hardwood glazed skeleton shutters 35 mm thick open rebated and prepared to receive guage etc but divided into squares, with plain chamfered or rounded, metered and riveted sash bars any numbers.( Note:- Necessary beading used for securing the wire mesh rates included in this items.

M&L for Plain fillets or beading of sectional area exc 3 & n. exc 6 sq.cm of 2nd class hard wood square, rectangular or triangular in section, clean sawn, secured with nails or brads for securing wiremesh or similar works put together with glue pinned at joints in complete all as specified and directed by Engineer - in - Charge.

S&F Solid FRP Door Frame of size 90mm x 45mm with single rebate of 32mm x 15mm to receive shutter moulded with fire retardent grade and saturated polyster resin and choped mat door framed shall be 2 mm thick and fill with suitable block in all the three legs the frame shall be covered with fiber glass all side MS stay shall be provided at the bottam to steady the frame as per specification shown on drawings.

S&F for factory made solid panel FRP door shutter shall be 30mm thick (style) glass fibre reinforced plastic panel door shutter of required colour with fire retardent grade and saturated polyster resin moulded to 3 mm thick FRP liminated for forming hollow rails and style with wooden frame and suitable block of seasoned wood inside at reqd places for fixing of fittings cast monolithically with 5 mm thick FRP panel and conforming to IS 14856:2000. as per specification shown on drawings.

S&F butt hinges of size 100 mm medium weight, stainless steel ISI marked complete all as specified.

S&F in repair butt hinges of size 100 mm medium weight, stainless steel ISI marked complete all as specified.

S&F aluminium handle, 150mm size, cast type, anodized (ISI marked) complete all as specified. Note : D type Handle and back side staple.

S&F in repair aluminium handle, 150mm size, cast type, anodized (ISI marked) complete all as specified.

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

S&Fin repair 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete, all as specified.

S&F in repair 300 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete, all as specified.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified.

S&F small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, articles of 2nd class hardwood, articles not exc 200 cu.cm each.

S&F in repair 150mm length floor door stopper of aluminium alloy body and tongue,anodised with hard drawan steel spring fixed in floor all as specified,

S & F hasp and staple, safety type of aluminium anodised100mm size fixed with screw complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying a coat of red oxide zinc chrome primer and two coats of synthetic enamel paint (for steel surfaces) including preparation of surface complete all as specified.

M&L preparing new wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted surfaces including as knotting, stopping, Burning off or removing, scraping etc,and then applying two coats of synthetic enamel paint (ordinary tint) on steel surfaces over 10cm width or girth complete all as specified and directed by Engineer - in - Charge.

M&L for applying one coat of wtaer proofing compound in chajja, staircase. etc by using 2 Sqm per 1 Kg WPC + cement in the proportion of (1:1.5) and making solution and applying by brush complete all as specified and as directed by Engineer-in-charge.

M & L for applying two coats of synthetic enamel paint over a coat of pink primer after complete removal of existing treatment with grinding on door and filling joints with putty wood and wood based surfaces of any description, over 10cm width or girth, not other wise described including preparation of old painted surfaces complete all as specified and directed by engineer in charge.

S&F Aluminium frame for doors, window, ventilators with one or more rebates including joining cleat for fixing etc complete with powder coating on Aluminium minimum thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners . Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required all complete as per the direction of Engineer-in-charge.

S&F Aluminium window (glazed and gauzed both),side hung type without sash bars, aluminum section weighing not less than 0.55 Kg/m including necessary joining cleats, glazing, clips, rubber packing, anodised aluminium snap beading screws,aluminium fitting such as peg stays 150mm long (01 nos), hinges type B-21 100mm long (02 Nos) suitable handle (01 No) with powder coating of any colour (thickness of powder coating not less than 50micron) etc complete all as specified and directed. Note: Glass and wiremesh will be measured and paid seperately.

S&F alumunium powder coated ventilator including frame and shutter, aluminium section weight not less than 0.55 kg/RM including necessary jointing cleats, glazing clips wtc and provision of neccessary rubber gasket for fixing glass panes complete all as specified and directed by Engineer-in-charge. Note : Glass panes and wiremesh shall be measured and paid seperately under respective item of BOQ.

S&F anodized aluminium grill powder coated of approved pattern of mesh 80x80mm, 6mm dia bars using U channel 25x12mm for windows / ventilators / doors complete, all as directed .

S&F 5.0 mm thick sheet glass ordinary quality in square not exceeding 0.5 sqm in each pane complete all as specified and directed .

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire, staples all as specified.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire, staples all as specified.

Dismantling Posts or struts (steel or RCC) any section ,including taking out embedded portion and making good disturbed ground post embedded in concrete complete all as specified and directed by Endineer -in -Charge.

Dismantling of barbed wire fence of any type and size complete all asspecified and directed by engineer in charge.

Excavating in post holes in soft/loose soil (or similar holes) each n exc 0.5 cum. getting out, returing, filling in and ramming earth or broken ruble mixed with earth around, in layers not exceeding 25 cm , watering, and removing surplus soil to a distance n exc 50 M and making good surface.

M&L PCC 1:3:6, type C-2, (40mm graded stone aggregate) as in foundation of posts and struts complete all as specified and directed by Endineer -in -Charge.

M&L for mild steel work as in post and struts in fencing including cutting tops to shape, drilling holes, notching for wire etc conforming to Fe-290 grade E-165 complete all as specified and directed .

M&L for flat iron for fixing chin link or hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and clountersunk for balusters running bars, for doors, balusters, nosing to steps including embneding in concrete and screwing etc for roof including securing bolts, posts and struts in fencing including cutting tops shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or reveting etc, and similar work conforming to Fe-290 or Fe-165.

S&F 10mm dia MS round bar for fixing of chain link fencing with post complete all as specified and directed.

M&L for preparation of new untreated steel and iron surfaces of any description, not exc. 10 cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of zinc chrome primer complete all as specified.

Supply only chain link fencing galvanised mild steel with specified size of 3 mm dia complete all as specified and directed. Note :- The weight of chain link fencing shall be ascertained by BOO as directed by GE and payment shall be paid accordingly. BOO duly countersigned by GE shall be enclosed with final bill.

Fixing only chain link fencing line wires,any mesh, size including line wire,any mesh,size and any type of standared ,rails,straining bolt, etc complete all as specifed and directed by engineer-in-charge. Note :- Supply of chain link fencing wire be measured and paid Separately.

S&F mild steel screw bolts (machine made) with hexagonal or square head at one end, and screwed the other,or screwed both end to be fitted with washer and one hexagonal/ square nut not exceeding 5cm long and dia of neck 11 to 15mm complete all as specified and directed by Engineer-in-Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed by Engineer-in-Charge.

S & F framed work such as grills, grating, etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 290 – Gde – 165 complete all as specified and directed.

M & L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-290(Grade E-165) complete all as specified and directed by Engineer-in-Charge.

M&L for hardcore of broken brick aggregate, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for factory made 60mm thick reflective type rubber moulded machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc.

M&L for cement concrete (1:3:6) type C1 using 20 mm graded crushed stone aggregate as in surface channels, drains, coping and benching including necessary formwork whrever required. Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.

Demolition and breaking up or taking down PVC/AC/CI/SSW 100mm bore pipe drain pipes, set in cement mortar including PCC haunching and bedding, complete all as specified and directyed by engineer in charge.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps complete all as directed.

S&F 110mm bore PVC (SWR) bend, any radius with access door.

S & F Stack clamps out of 50mm by 5 mm flat iron and 16mm dia round iron stays for 100mm bore of pipe, including bolts and nuts and securing ends of stays to wall or roof etc complete all as specified and directed by Engineer - in - Charge.

Demolition of Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided.

Water proofing treatment to sunken slab and adjjoining vertical surfaces complete all as specified and directed by Engineer-in-charge ad under :- (a) M&L rendering 10 mm thick in cement plaster (1:3) using coarse sand mixed with integral water proofing compound trowel even and smooth with steel trowel on sunken surfaces Note : (a) WPC shall be measured and paid separately. (b) Applying first coat of chemical pidifin 2K(Dr Fixit) on cleared RCC surfaces @ 0.86 Kg/Sqm (Minimum) as recommended by manufacturer. (c) Provide a layer glass fibre mesh of size 2.25mm x2.25mm (45 GSM) over first coat of chemical Pidifin 2K as per manufacturers recommendation. (d) Applying second coat of chemical Pidifin 2K (Dr Fixit) @ 0.86 Kg/Sqm (minimum) layer glass fibre mesh of size 2.25mm x 2.25mm (45 GSM) as recommended by manufacturers. Note Plan area of floor should be measured

M&L for PCC 1:5:10, type E-2 using 40mm graded stone aggregate as in filling of sunken floors complete all as specified and directed by Engineer-in-Charge.

M&L 40 mm bore GI pipe medium grade, made to shape as in spout pipe in sunken/ verandah/ Balcony complete all as spedifed

M&L for machine cut kota stone slab flooring, cills 20-25mm thick including 10 mm thick rendering in cement mortar 1:4 base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed by engr in charge. Note :- Rendering will be done in course sand (toka sand) only

M&L for 30 cm x 30 cm x (20 to 25) mm thick chequered cement concrete tiles(rubber moulded) set jointed and pointed in neat cement slurry in floors with grey cement including 15mm thick screed in CM 1:6 with pigments complete all as specified and directed by Engineer-in-Charge.

Demolition of RCC slab, RCC tank, chajjas and similar items complete all as specified and directed by Engineer - in - Charge.

M&L for reinforced cement concrete type B1 1:2:4 (20 mm graded stone aggregate) as in slab supported on walls, beam and column in floors, roofs, landings, balconies, deck slab, chajja, tank staging and in shelves and etc and setting in mortar complete with joints to match complete all as specified and directed by Engineer-in-Charge.

Repair to damaged concrete slab by using micro mortar and concrete in following stages:- (a) Removing the falling mortar and concrete from RCC slab and cutting the affected area in geometrical shape. (b) Cleaning the rusted reinforcement and applying rust removal. (c) Inserting addl reinforcement in case the cross sectional area reduction is more than 20 percent. Welding the reinforcement with existing one and supporting the new supporting adequately on walls if required with grout. (d) Providing micro mortar and concrete over bond coat to cover the reinforcement and slab surface. (e) Providing adequate formwork and scaffolding if required. (f) Curing the surfaceRust removal, Bonding agent, grout, micro mortar and concrete and related chemicals shall be of Dr Fixit/BASF/ STP. Work is to be got executed from authorized applicators of company.

M&L for use and waste of form work through finished surface of soffits of suspended slab as roof slabs, floor, lamnding and similar work not exceeding 200 mm thick complete all as specified and directed by engr in charge

M & L mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia

Dismantling cast iron work of any description and any position complete all as specified and directed by Engineer - in - Charge.

Excavation in trenches not exceeding 1.5 Mtr wide and not exceeding 1.50 Mtr in depth for foundation, etc., not exceeding 10 Sqm on plan in soft /loose soil; & getting out complete all as specified and directed by Engineer - in - Charge.

M&L for PCC 1:4:8, type D2, using 40mm graded stone aggregate as in sub base, floors foundation filling & mass concrete complete all as specified & directed by Engineer in charge.

Returning, filling in, including spreading, leveling, watering and well ramming in soft/loose soil in layer not exceeding 25 cm thick complete all as specified and directed by Engineer - in - Charge.

Removing excavated material (Soil) outside MOD land all as specified and directed by Engineer - in - Charge.

Cutting in to existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for as specified dia complete all as specified and directed by engineer in charge.

M & L for cutting bushes around the bldg & manholes and on the route of sewer line and refixing manhole cover properly all as specified & directed by Engr-in -charge

S&F 100mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron bends sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron bends sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron bends (any radius) with duck's foot or heel rest complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron bends (any radius) with duck's foot or heel rest complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engineer - in - Charge.

S&F 75 mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engineer - in - Charge.

M& L extra over 100 mm bore cast iron pipes and fittings if lead joint is provided in lieu of cement joint complete all as specified and direcetd by engineer in charge

M& L extra over 75 mm bore cast iron pipes and fittings if lead joint is provided in lieu of cement joint complete all as specified and direcetd by engineer in charge

M&L for CI floor trap 75 mm with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified and directed by Engr-in-charge.

M&L for CI floor trap 100 mm with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified and directed by Engr-in-charge.

S&F Stainless steel fancy type peg set of six and fixed in position with steel screws complete all as specified and directed by Engineer-in-charge

M& L for providing and fixing stainless steel (Grade 304) railing made of Square hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) & Providing baluster and necessary fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

M&L for Obliterating old writing of any description, n exc 0.1 sq. m, with paint to match existing work etc complete all as specified and directed by Engineer - in - Charge.

M&L for writing letters or figures with fluorecent paint (Block, Roman, Italic or Indian) n exc. 30 cm high etc complete all as specified and directed by Engineer - in - Charge.

Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed by Engineer - in - Charge.

M & L for concealed point wiring complete for light/ fan on independent /combine board with cable 1.5 sqmm (Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for modular metal flush boxes suitable length and thickness for mounting, switches, sockets,fan regulator with modular cover plate with frame and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 1.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.

All as per Ser item No 180.00 above but for one switch socket combination 5/6 amp on independent board complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 180.00 above but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 180.00 above but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 180.00 above but for one light point controlled by two 2 ways switches complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 180.00 above but for call bell point complete all as specified and directed by Engineer - in - Charge.

S & F in replacement modular switch 5/6 Amps single pole one way,one module including modular cover plate with frame and metal flush box complete all as specified and directed by Engineer - in - Charge.

S & F in replacement modular switch socket combination 5 pin, type 5/6 Amps5 in 1 flush type including modular cover plate and metal flush box with frame complete all as specified and directed by Engineer - in - Charge.

S & F in replacement modular switch socket combination 6 Pin, 5/16 Amps flush type including modular cover plate with frame and metal flush box complete all as specified and directed by Engineer - in - Charge.

S & F modular switch 5/6 Amps single pole two ways complete all as specified and directed by Engineer – in - Charge.

S & F modular socket outlet 5 pin 5 Amps flush type complete all as specified and directed by Engineer - in - Charge.

Supply and fix in replacement industrial socket metal clad plug and socket with MCBs single pole 20 Amp complte all as specified and directed by Engineer - in - Charge.

S&F in replacement modular bell push 5 Amp complete all as specified and directed by Engineer - in - Charge.

S & F in replacement modular stepped type, fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge

S&F Buzzer AC 230 volt single pole ding dong type complete all as specified and directed by Engineer - in - Charge.

S & F in replacement ceiling rose surface bakelite three terminals complete all as specified and directed by Engineer - in - Charge.

S & F in replacement of light fitting with LED batten with aliminium housing and integrated electronic driver, 20/22 watt having input voltage AC90-300V, 50 Hz , 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge.

S&F in replacement security light fitting LED TYPE 25 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 32 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge

S&F in replacement decorative wall light,brushed nickle finish fixture with OPAL glass diffuser including 4 watt LED filament lamp E14 base complete all as specified and directed by Engineer - in - Charge ( make- havells cat part no: LHFOAIC1TZ1I040 or equivalent make in bajaj,crompton

S & F in replacement LED Bedside Light (White,3000k) 3 Watt, with flexible arm suitable for reading complete all as specified and directed by Engineer - in - Charge.

S & F in replacement Water tight bulk head fitting,comprision of connector galvanised cast iron back plate,weather proof enamelled gallery, glass well,and including 10 watt LED lamp all as specified and directed by Engineer - in - Charge

S & F in replacement compact & decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1X10 watt fitting 2 ft version including LED lamp 10 watt complete all as specified.

S & F in replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge

S&F LED lamp 9W for angle holder complete all as specified and directed by Engineer - in - Charge.

S & F in replacement of sub-main wiring with PVC insulated and un-sheathed 4 x 6.00 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in and including PVC "medium quality" conduit as per size required including 2 x 6Sqmm (Nominal area) copper cable as earth contiunity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer-in-Charge. Note : (a) PVC cable and PVC conduit shall be ISI marked. (b) Four length of 6 Sqmm cable and two length of 6 Sqmm earth cable along with PVC conduit will be measured as one running length.

S&F in replacement sub main two single core PVC copper conductor unsheathed wire multi stranded 4 sqmm FRLSH including cutting chasing and grouting PVC pipe including Tee, Elbow, Bend etc and including 4.0 sqmm copper conductor single core wire connected by common earth all as specified. Including 20 mm dia concealed PVC conduit, medium grade, ISI marked complete all as specified and directed by Engineer-in-Charge. Note :- Two lengths of 4.0 sqmm cable and one length of 4.0 sqmm earth cable along with PVC conduit will be measured as one running length

S&F in replacement sub main two single core PVC copper conductor unsheathed wire multi stranded 2.5 sqmm FRLSH including cutting chasing and grouting PVC pipe including Tee, Elbow, Bend etc and including2.5 sqmm copper conductor single core wire connected by common earth all as specified. Including 20 mm dia concealed PVC conduit, medium grade, ISI marked complete all as specified and directed by Engineer-in-Charge. Note :- Two lengths of 2.5 sqmm cable and one length of 2.5 sqmm earth cable along with PVC conduit will be measured as one running length

S&F in replacement Sheet metal enclouser for doble door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting VTPN 4 Way 415 Volt ISI marked 250Amps busbar stove enameled dust and vermin proof,IP:43 protection suitable for incorporation FP MCCB(V-Tech) N3 Frame upto 250A, Isolators and including give connection with wire and cable etc complete all as specified and directed by Engineer-in-Charge.

S & F in replacement sheet metal enclosure for double door DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted TP & N 6 ways, 415 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S&F in replacement MCCB TP & N 100 Amps with breaking capcity 16kA ,Fixed TM and 415 volts AC Supply ISI marked complete all as specified and directed by Engineer - in - Charge.

S & F in replacement MCB ‘B’ series type suitable for 415 volts, 10 KA, AC supply 25 to 63 Amps, triple pole (TP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in replacement MCB ‘B’ series type suitable for 415 volts, 10 KA, AC supply 40 to 100 Amps, triple pole and neutral (TPN) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in replacement MCB ‘B’ series type suitable for 240 volts,10 KA, AC supply 6 to 32 Amps , single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

M & L in repair for earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GI and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil ,returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed by Engr -In - Charge

Dismantling and depositing of old unserviceable ceiling fans of any size in MES yard complete all as directed.

S&F Heavy duty metal body exahust fan of 300mm sweep, 240 volt, copper winding, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to disturbed wall in cement mortar(1 :4) white washing matching with existing colour etc. Note : Dismantling of old u/s fan shall be deposited in MES Store yard & rateincludes in quoted amount.

S&F ceiling fans AC single phase 230/240 V of size 1200 mm sweep without regulator having Min air delivery 210 CFM with service value 6.00 BEE 5 star rated with brushless direct current motor (BLDC) complete with electrical connection providing three core round flexible copper conducter cable of suitable size complete all as specified and directed by Engineer-in-charge. Note -Dismantling of old unserviceable fan shall be deposited in MES Store yard & rate includes in quoted amount.

S&F storage type water heater (Geyser) electrical operated 230/240 Volts 50 ltr capacity, BEE 5 star rated complete with all safety equipment and accessories such as safety valve, thermostat, fusible plug, etc. required for proper functionality & including electric/earth connections and carrying out grounting & complete installations with mounting bolts, nuts including testing after installation complete all as specified and directed by Engineer-in-charge.

Supply and filling in sand for cable protection complete all as specified and directed

Supply and lay standard size bricks subclass B type complete all as specifed and directed.

Supply and lay in replacement jointing and testing and commissioning in replacement of 35 Sqmm x 3.5 core XLPE insulated, screened, PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by Engineer-in-Charge.

Supply and fix 3 pin telephone socket RJ 11 with metal flush box having holes for 20 mm conduit entry for telephone connection all as specified and directed by Engineer- in- charge.

S & F Rigid non-metallic PVC conduit 20 mm dia inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.

Supply and lay GI pipe 50 mm light grade for cable protection in walls trenches or any situation including clamp nut bolt etc complete all as specified and directed by Engineer-in-Charge.

M/s HANS BROTHERS

J and P CONTRACTOR

M/S KARNI CONSTRUCTION COMPANY