Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹13.3 CrAccepted-AOC BARNALI TOWER MIRZA KAMRUP ASSAM PIN 781125 | KAMRUP | ASSAM | 781125 | ₹13.3 Cr | L1 | Accepted-AOC Work Order Issued |
| 2 | L2₹14.7 CrRejected-AOC BHASKAR NAGAR BYE LANE NO 2 GUWAHATI 21 | SOUTH SALMARA MANCACHAR | ASSAM | 783127 | ₹14.7 Cr | L2 | Rejected-AOC L2 |
Tender Value
₹13.3 Cr
EMD Value
₹26.7 L
Closing Date
1 Apr 2024, 2:00 pmClosed
Spl CE PWD(Bldg), H AND E, Assam, Chandmari, Ghy-3
O/O The CE, PWD(Bldg), Assam, Chandmari, Ghy-3
Upgradation of Tularam Bafna Hospital from 50 beds to 200 Beds at Amingaon, Kamrup
2024_PWBNH_37131_1
CE/TB-IV/49/2016/Pt/05 Dated Guwahati 5th March 2024
Open Tender
Civil Works - Building
365 days
Amingaon
Please refer Tender documents.
5 documents required · 5 mandatory
₹20,000
₹26.7 L
Yes
23 Aug 2024
12 Mar 2024
3 Apr 2024
12 Mar 2024
1 Apr 2024
18 Mar 2024
Amount
Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu?ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete above plinth level. Mild steel and Medium Tensile steel bars
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in?charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers
Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts
Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc., including edges
Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)
15 mm cement plaster on rough side of single or half brick wall of mix: .1 1:4 (1 cement: 4 coarse sand)
20 mm cement plaster of mix : 13.6.1 1:4 (1 cement: 4 coarse sand)
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 1200 mm
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent
Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks: 1:4 (1 cement : 4 coarse sand)
Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means,including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge. Profile E Fixing with adjustable lugs with split end tail to each jamb
Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.
Providing and fixing M.S. grills of required pattern in frames of window Fixed to steel windows by welding
Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm
Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work
Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied@ 2.20 kg/10 sqm)
Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works
Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work
Providing and fixing false ceiling at all height including providing andfixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (bothside inclusive) as per IS : 277 and consisting of a, at 1200 mm centre to centre, one flange 25x10x0.50 mm mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including ............ jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction ofthe Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar
Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper
Providing, fitting and fixing of 30mm thk BWP grade (Green/Century/Archid or equivalent) solid core flush door with 1mm thick laminate (Green/Century/Archid or equivalent make) on both sides along with fittings, beadings etc. fixed with 4'' Heavy Duty SS hinge with neccessary adhesive complete as specified and directed by the Department.
Providing and fixing white vitreous china pedestal type water closet(European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets,40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting andmaking good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
Providing and fixing PTMT Waste Coupling for wash basin and sink,of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40 mm dia
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore
Providing and fixing plain bend of required degree. 75 mm dia Sand cast iron S&S as per IS -1729
Providing and fixing plain bend of required degree. 100 mm dia Sand cast iron S&S as per IS - 1729
Providing and fixing PTMT pillar cock of approved quality and colour. 15 mm nominal bore, 125 mm long foam flow, weighing not less than 120 gms
Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms
Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet Sand cast iron S&S as per IS - 3989
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 75 mm dia Sand cast iron S&S as per IS - 1729
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia Sand cast iron S&S as per IS - 1729
Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete : 100 mm Sand cast iron S&S as per IS - 1729
Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 40 mm nominal dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 80 mm nominal dia Pipes
Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead : 450 mm diameter pipe
Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead 18.28.8 400 mm diameter pipe
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore
Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 20 mm nominal bore
Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter
Providing and fixing PTMT grating of approved quality and colour. Circular type 125 mm nominal dia with 25 mm waste hole
Providing and fixing PTMT stop cock of approved quality and colour. Concealed stop cock, 15 mm nominal bore, 108 mm long,weighing not less than 108 gms
Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Reducing Tee For 48.60 mm x 42.70 mm outer dia pipe
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 20 mm nominal dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 40 mm nominal dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 100 mm nominal dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 150 mm nominal dia Pipes
Providing and fixing 3 layer PP-R (Poly propylene Random copolymer)pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge. External work PN - 10 Pipe, 75 mm OD (SDR-11)
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal
Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal
Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way-100 mm dia M.S. Pipe
25mm Air release valve as per IS:14845 ISI Marked
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80mm dia
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 100mm dia
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 following sizes as required: 80 mm dia
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 following sizes as required: 100 mm dia
Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25 mm dia
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 32 mm dia
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 50 mm dia
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 65 mm dia
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm dia
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required 100 mm dia
Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. 1620 lpm at 70 m Head
Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 56 m Head
Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads. 450 lpm at 35 m Head
Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.
Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.
Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 10 x 1.5 sq. mm
Supplying, installation, testing & commissioning of addressable manual call point complete as required.
Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.
Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 1000mm
Supply & Fixing of 04 Kg. Capacity ABC type Fire Extinguisher. (Make: Life Secure)
Supply & Fixing of 4.5 Kg. Capacity Co2 type Fire Extinguisher. (Make: Life Secure)
Supply & Fixing of 09 Ltr. Capacity AFFF type Fire Extinguisher. (Make: Life Secure)
Supply & Fixing of SS Ball Valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/Cm2 of approved Quality as a specified (Make: Zoloto/ Sant)
Supply & Fixing of Hose Cabinet 450(W)×250(D)×450(H) as per sample approved by the consultant. The Construction of the cabinet to be in 18G CR Sheet with red colour powder coating.
Supplying, Fitting & Fixing of Pressure Guage
Supplying, Fitting & Fixing of Pressure Switch
Supplying, Fitting & Fixing of Automatic Panel Auto start Manual off with Fittings For Main & Jockey Pump.
Supplying, Fitting & Fixing of Automatic 5HP Panel Auto start Manual off with Fittings For Terrace Pump.
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Mild steel and Medium Tensile steel bars
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)
Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete
Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1:3 (1 cement : 3 coarse sand)
12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand)
15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix 1:3 (1 cement: 3 fine sand)
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Supplying, Fitting and Installation of Main Table Model: Edge Perform Executive Table Main Table Size:1500W×750D×750Ht Make: Featherlite Company.
Supplying, Fitting and Installation of Main Chair Model: Astro MB Make: Featherlite Company.
Supplying, Fitting and Installation of Visitor Chair Model: Smart VA Make: Featherlite Company.
Supplying, Fitting and Installation of Filling Cabinet Main Table Size:900W×450D×2100Ht Make: Featherlite Company.
Supplying, Fitting and Installation of Steel Racks M.S. Slotted Angle Rack Model: Metal Rack Size:900W×375D×1950Ht Make: Featherlite Company.
Supplying, Fitting and Installation of Main Table Model: Versaline 1575 Size:1500W×750D×750Ht Make: Featherlite Company.
Supplying, Fitting and Installation of Chair Model: Magna VA With Arms Make: Featherlite Company.
Supplying, Fitting and Installation of Counter Main Chair Model: Contact Project MB Make: Featherlite Company.
Supplying, Fitting and Installation of Waiting Chair Model: Bruney Metal Tandem Two Seater Size:1350L×690D×825Ht Make: Featherlite Company.
Supplying, Fitting and Installation of Waiting Chair Model: Bruney Metal Tandem Three Seater Size:1980L×690D×825Ht Make: Featherlite Company.
Supplying, Fitting and Installation of Sofa Model: E007 Two Seater Sofa Make: Featherlite Company.
Supplying, Fitting and Installation of Centre Table With 18mm PLB Size:1050×525×450 Make: Featherlite Company.
Supplying, Fitting and Installation of Square Centre Table With 18mm PLB Top and PC Swage Leg Size:600W×600D×450ht Make: Featherlite Company.
Supplying, Fitting and Installation of Storage/Wardrobe Size:900W×450D×1800ht Make: Featherlite Company.
Supplying, Fitting and Installation of Chair Model: Tang Make: Featherlite Company.
MEDICAL OXYGEN SYSTEM Main Oxygen Manifold 6+6 cylinders with NRVs, Tail pipes with Oxygen Control Panel
MEDICAL OXYGEN SYSTEM Emergency Oxygen manifold 6 cylinders with NRV's, copper pig tail pipes, and pressure reducing unit.
MEDICAL VACUUM SYSTEM Vacuum System with Twin Vacuum pumps, Ingersoll-Rand make Model V255 each with 5 HP motor, Silencer, Filter, interconnectingn pipes, NRV, auto switch gear assy. Air Receiver Tank-1000 Ltr
Distribution Copper Pipe: duly Medical Grade, seamless, fully degreased and half-hard (Designated to R250). It should confirm and meets with the BS EN 13348 standard. Chemical Composition as per CU.DHP to 1190-1and CW024A to EN 1412. Maximum total Carbon Content 0.20 Mg/dm2. Should be certified by Lloyds Register of Services. Copper Pipe 12 mm OD X 0.7 mm thickness
Distribution Copper Pipe: duly Medical Grade, seamless, fully degreased and half-hard (Designated to R250). It should confirm and meets with the BS EN 13348 standard. Chemical Composition as per CU.DHP to 1190-1and CW024A to EN 1412. Maximum total Carbon Content 0.20 Mg/dm2. Should be certified by Lloyds Register of Services. Copper Pipe 15 mm OD X 0.9 mm thickness
Distribution Copper Pipe: duly Medical Grade, seamless, fully degreased and half-hard (Designated to R250). It should confirm and meets with the BS EN 13348 standard. Chemical Composition as per CU.DHP to 1190-1and CW024A to EN 1412. Maximum total Carbon Content 0.20 Mg/dm2. Should be certified by Lloyds Register of Services. Copper Pipe 22 mm OD X 0.9 mm thickness
Distribution Copper Pipe: duly Medical Grade, seamless, fully degreased and half-hard (Designated to R250). It should confirm and meets with the BS EN 13348 standard. Chemical Composition as per CU.DHP to 1190-1and CW024A to EN 1412. Maximum total Carbon Content 0.20 Mg/dm2. Should be certified by Lloyds Register of Services. Copper Pipe 28 mm OD X 0.9 mm thickness
Zonal / Isolation Valves Brass Fittings 15 mm
Zonal / Isolation Valves Brass Fittings 22 mm
Zonal / Isolation Valves Brass Fittings 28 mm
Gas Outlets, Front Insertion type Double Lock with Probe Oxygen
Gas Outlets, Front Insertion type Double Lock with Probe Vacuum
Accessories Oxygen Flowmeter with Humidifier
Accessories Ward Vacuum Unit with 600 ML. Collection Jar (complete with vacuum regulator)
Accessories Oxygen Adopter/Probe for Ventilator Hose
Accessories Low Pressure Tubes
Area Alarm, Indigenous Area Alarm 2 gas Service
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group A
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group B
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 4 sq. mm + 2 X 4 sq. mm earth wire
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 6 sq. mm + 2 X 6 sq. mm earth wire
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 10 sq. mm + 2 X 6 sq. mm earth wire
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 16 sq. mm + 2 X 6 sq. mm earth wire
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm)
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 4 Module (125mmX75mm)
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 6 Module (200mmX75mm)
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 8 Module (125mmX125mm)
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 12 Module (200mmX150mm)
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 5/6 A Switch
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 15/16 A Switch
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 3 pin 5/6 A socket outlet
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 6 pin 15/16 A socket outlet
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
Supplying and fixing brass batten/ angle holder including connection etc. as required.
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way , Double door
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door
Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door
Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 A,30KA,FPMCCB
Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required
Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Upto 35 sq. mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Above 35 sq. mm and upto 95 sq. mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Above 95 sq. mm and upto 185 sq. mm
Supplying with fitting and fixing of 40 A DP 10 KA 240/415 V 50 Hz MCB with making necessary connection as approved and directed by the deptt. (Legrand Make) Model no. 408637
Supplying with fitting and fixing of 40 A 4P 10 KA 240/415 V 50 Hz MCB with making necessary connection as approved and directed by the deptt. (Legrand Make) Model no. 408794
Supplying with fitting and fixing of 63 A 4P 10 KA 240/415 V 50 Hz MCB with making necessary connection as approved and directed by the deptt. (Legrand Make) Model no. 408794
Supplying with fitting and fixing of 100 A 4P 10 KA 240/415 V 50 Hz MCB with making necessary connection as approved and directed by the deptt. (Legrand Make) Model no. 408794
Supplying with fitting and fixing of 30/100/300 mA sensitivity 240/415 V 50 Hz 4 P RCCB with making necessary connection as approved and directed by the deptt. (Legrand or eqivalent Make)
Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department as required
Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt. as required complete and as directed by the Department. (Cromton or equivalent make)
supplying, fitting & fixing of LED Bulb 10 W non-dimmable in the existing batten/angle holder as required and as directed by the department.
supplying, fitting & fixing of LED Tube light 20 Watts as directed by the department.(Philips or equivalant make)
Supplying, installation, testing and commissioning of the following indoor Decorative surface mounted fitting LED round ceiling light and as required and as directed by the department. (12 Watt Philips or equivalent make)
Supplying, installation, testing and commissioning of the following indoor surface ceiling fitting LED 15 W down lighter luminaries and as required and as directed by the department. (Philips or equivalent make)
Supplying, installation, testing and commissioning of the following indoor Decorative Recessed mounted 2' x 2' LED 36 W down lighter luminaries and as required and as directed by the department. (Philips or equivalent make)
Supplying including installation, connection as approved by the Deptt., testing and commissioning of submersible pump set Three Phase with motor rating of 5 HP complete as directed and specified by the deptt. Including Digital control panel and connection cable etc. (Cromption or equivalent make)
Supply of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium wire for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable as specified and directed by the deptt. (Havells, RR, Polycab or equivelent make as approved by this Deptt.) 16.00 Sq. mm. 4 Core armoured U.G. cable
Supply of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium wire for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable as specified and directed by the deptt. (Havells, RR, Polycab or equivelent make as approved by this Deptt.) 25.00 Sq. mm. 4 Core armoured U.G. cable
Supply of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium wire for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable as specified and directed by the deptt. (Havells, RR, Polycab or equivelent make as approved by this Deptt.) 50.00 Sq. mm. 4 Core armoured U.G. cable
Supply of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium wire for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable as specified and directed by the deptt. (Havells, RR, Polycab or equivelent make as approved by this Deptt.) 150.00 Sq. mm. 4 Core armoured U.G. cable
Supply of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium wire for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable as specified and directed by the deptt. (Havells, RR, Polycab or equivelent make as approved by this Deptt.) 240.00 Sq. mm. 4 Core armoured U.G. cable
Supplying and installation and commissioning of panel board size 1400 mm (H) X 1100 mm (W) X 350 mm (D) with double door made out with 1.6 mm CRCA sheet steel, 3-phase, suitable for floor mounted, user front facia, Powder coated for long lasting finish, cubical type, suitable cable entry provision and including of all necessary electrical protections including Aluminium Bus bar etc. complete neatly internal wiring done as specified and directed by the department comprising of the following electrical items. 1. 250 Amp 4 pole MCCB-1 No, 2. 100 Amp FP MCB-2 No, 3. 63 Amp FP MCB-3 Nos, 4. 40 A 4 P MCB 3 Nos., 5. 40 A DP MCB 4 Nos, including Digital Ammeter, Voltmeter etc.
Supplying and installation and commissioning of panel board size 1250 mm (H) X 1100 mm (W) X 350 mm (D) with double door made out with 1.6 mm CRCA sheet steel, 3-phase, suitable for floor mounted, user front facia, Powder coated for long lasting finish, cubical type, suitable cable entry provision and including of all necessary electrical protections including Aluminium Bus bar etc. complete neatly internal wiring done as specified and directed by the department comprising of the following electrical items. 1. 250 Amp 4 pole MCCB-1 No, 2. 100 Amp FP MCB-2 No, 3. 63 Amp FP MCB-3 Nos, 4. 40 A 4 P MCB 3 Nos., 5. 40 A DP MCB 4 Nos, including Digital Ammeter, Voltmeter etc.
Supplying and installation and commissioning of panel board size 1400 mm (H) X 1100 mm (W) X 350 mm (D) with double door made out with 1.6 mm CRCA sheet steel, 3-phase, suitable for floor mounted, user front facia, Powder coated for long lasting finish, cubical type, suitable cable entry provision and including of all necessary electrical protections including Aluminium Bus bar etc. complete neatly internal wiring done as specified and directed by the department comprising of the following electrical items. 1. 200 Amp 4 pole MCCB-1 No, 2. 100 Amp FP MCB-3 No, 3. 63 Amp FP MCB-3 Nos, 4. 40 A 4 P MCB 3 Nos., 5. 40 A DP MCB 4 Nos, including Digital Ammeter, Voltmeter etc.
Supplying and installation and commissioning of panel board size 1400 mm (H) X 1100 mm (W) X 350 mm (D) with double door made out with 1.6 mm CRCA sheet steel, 3-phase, suitable for floor mounted, user front facia, Powder coated for long lasting finish, cubical type, suitable cable entry provision and including of all necessary electrical protections including Aluminium Bus bar etc. complete neatly internal wiring done as specified and directed by the department comprising of the following electrical items. 1. 160 Amp 4 pole MCCB-1 No, 2. 100 Amp FP MCB-2 No, 3. 63 Amp FP MCB-3 Nos, 4. 40 A 4 P MCB 3 Nos., 5. 40 A DP MCB 4 Nos, including Digital Ammeter, Voltmeter etc.
Supplying installation, testing and commissioning of stainless steel automatic hospital bed cum passenger Elevator having contract speed of 1 Metre/Sec (approx.) mps serving different floor in the existing lift shaft as per detailed specification as per company, having following additional features. No of Stops/Entrances - 6 ARD facilityAutomatic and multiray electronic door detecting system door Stainless steel car in hairline finish. Battery operated alarm bell and emergency light. Overload warning device. Voice synthesizer. Etc. 15 passenger (1020 Kg)
30 KVA On-Line UPS System (Orion or equivalent make as approved by the Deptt.) with PWM-IGBT technology 360V AC Input (300V – 470V A 3 Ph input- 1 Ph output With Isolation Transformer 18KW output with 0.8 output PF 60 min backup using SMF battery
Supplying including, installation, connection as approved by the Deptt., testing and commissioning of Lighting Arrestor complete as directed and specified by the deptt. including all necessary materials.
Intercom (Telephone) system works :Supplying of NEC Intercom with 72 Extension, 4 Trunk, 2 Digital Port
Intercom (Telephone) system works : Supplying 100 Pair KEI/RR Telephone Wire
Intercom (Telephone) system works : Supplying 4 Pair KEI/RR Telephone wire
Intercom (Telephone) system works :Supplying 100 Pair MDF BOX
Intercom (Telephone) system works :Supplying 20 Pair MDF BOX
Intercom (Telephone) system works :Supplying UPS 1 KVA Ofline
Intercom (Telephone) system works :Supplying 101300
Intercom (Telephone) system works : Installation, testing & commissioning charge
Intercom (Telephone) system works :Supplying Telephone with caller ID
Intercom (Telephone) system works :Supplying Digital phone
CCTV system works :Supplying 4 MP IP Dome Camera Hikvision
CCTV system works: Supplying 128 CH NVR Hikvision
CCTV system works: Supplying 16 port Giga POE Switch Hikvision
CCTV system works: Supplying 6 U Rack
CCTV system works: Supplying 42 U Rack
CCTV system works: Supplying Connector
CCTV system works: Supplying 4 MP IP Bullet Camera Hikvision
CCTV system works: Supplying Hardisck 10 TB Seagate
CCTV system works: Supplying Cat 6 Wire Hikvision
CCTV system works: Supplying 55" TV LG
CCTV system works: Installation, testing & commissioning charge
Nurse calling system works - Supplying Calling Button
Nurse calling system works - Supplying 1 mm 2 core wire
Nurse calling system works -Supplying Calling system Display
Nurse calling system works - Installation, testing & commissioning charge
Lan connection works-Supplying lo Box Digisol
Lan connection works-Supplying Cat 6 Wire Digisol
Lan connection works-Supplying 8 port Giga Switch Digisol
Lan connection works-Supplying 16 port Olga Switch Digisol
Lan connection works-Installation charges, testing & commissioning charge works
Cassette & Split AC :Supply of Voltas make Inverter Cassette AC with High Efficiency Twin Roatary Compressor Cordless Remote & suitable Eco friendly Gas R-32 1.57R
Cassette & Split AC : Supply of Voltas make Inverter Cassette AC with High Efficiency Twin Roatary Compressor Cordless Remote & suitable Eco friendly Gas R-32 2TR
Cassette & Split AC :Supply of Voltas make Inverter Cassette AC with High Efficiency Twin Roatary Compressor Cordless Remote & suitable Eco friendly Gas R-32 3TR
Cassette & Split AC : Supply of Voltas Make Inverter 3Star Split AC 1TR
Cassette & Split AC : Supply of Voltas Make Inverter 3Star Split AC 1.STR
Cassette & Split AC : Supply of Voltas Make Inverter 3Star Split AC 2TR
Installation, testing & commissioning of Inverter Cassette AC 1.5TR
Installation, testing & commissioning of Inverter Cassette AC 2TR
Installation, testing & commissioning of Inverter Cassette AC 3TR
Installation, testing & commissioning of of Voltas Make Inverter 3Star Split AC 1TR
Installation, testing & commissioning of of Voltas Make Inverter 3Star Split AC 1.STR
Installation, testing & commissioning of of Voltas Make Inverter 3Star Split AC 2TR
Supply, fitting fixing of Refrigernat Copper Pipe inverter Cassette AC For 1.STR Cassette AC (BotitSuction + Liquid Line & Proper Insulation)
Supply, fitting fixing of Refrigernat Copper Pipe inverter Cassette AC For 2 TR Cassette AC (Both Suction + Liquid Line & Proper Insulation)
Supply, fitting fixing of Refrigernat Copper Pipe inverter Cassette AC For 3TR Cassette AC (Both Suction + Liquid Line & Proper Insulation)
Supply, fitting fixing of Refrigernat Copper Pipe inverter Split AC For 1TR Inverter Split AC (Both Suction + Liquid Line & Proper Insulation)
Supply, fitting fixing of Refrigernat Copper Pipe inverter Split AC For 1.5TR Inverter Split AC (Both Suction + Liquid Line & Proper Insulation)
Supply, fitting fixing of Refrigernat Copper Pipe inverter Split AC For 2TR Inverter Split AC (Both Suction + Liquid Line & Proper Insulation)
Supply, fitting fixing of C-PVC conduit pipe for condensate drain line for indoor unit with size 25mm with 2mm wall thickness with properly laying as per site.
Hanging Arrangement for Cassette AC
Supply, fitting fixing of ODU Stand for Casseette AC
Supply, fitting fixing of ODU Stand for Split AC
Supply and connecting electrical cabling with properly laying as
Supply, fitting fixing of 4KVA voltage stabilizer
Supply, fitting fixing of SKVA voltage stabilizer
HVAC Work : Supply of Variable Refrigerant Volume / Flow Air-conditioning System Supply, Instalaltion, testing and commissioning of Variable Refrigerant Flow /(VRF) Modular type (with the latest technology/version) with All-Inverter driven Compressor, system with stepless modulation for both heating & cooling modes, complete with indoor and outdoor units, individual remote controller and centralized controller, interconnected refrigerant piping with insulation, V joints, Reqigerant to be used shall be - R 410 A only. The unit shall be suitable to work on 415V +/- 10%, 3 Phase, 50H, AC power supply. Cool / Heat Mode (10 HP+10HP= 20 HP
HVAC Work : Supply of Variable Refrigerant Volume / Flow Air-conditioning System Supply, Instalaltion, testing and commissioning of Variable Refrigerant Flow /(VRF) Modular type (with the latest technology/version) with All-Inverter driven Compressor, system with stepless modulation for both heating & cooling modes, complete with indoor and outdoor units, individual remote controller and centralized controller, interconnected refrigerant piping with insulation, V joints, Reqigerant to be used shall be - R 410 A only. The unit shall be suitable to work on 415V +/- 10%, 3 Phase, 50H, AC power supply. Cool / Heat Mode (8 HP+12HP= 20HP
Supply of Refnet Indoor Refnet / Branch Joint
Supply, Installation, Testing and Commissioning of Ductable Split Acs of Capacity 5.5 TR for Pre/Post OT Room connected with 8 HP VRF ODU unit.
Supply of Air Handling Unit ( IOU) of Floor/ Ceiling Suspended AHU of 0.6 rem GI Double Skinned DX AHU with Al anodized thermal break frame structure injected with minimum 32 mm thick 40 kg/m3 PUF insulation; GI Panel shall be powder coated from both iner and outer side , the AHU shall comprising of: Mixing box / Anodized Aluminum Aerofoil Low leakage Fresh / Balancing / Exhaust Air Damper / Pre-Filter section with EU- 4 compliant Prefilters for Return and Fresh Air / Al finned 8 Row deep -13 FPI double skin sandwitch insulated removable 55 304 condensate drain pan / Fine filter EU 7 / fine filter section with EU 9 compliant / Fan section with Hi static best efficiency Plug Fan driven by suitable pole Eff-1 TEFC Motor with Drive Package / Al aerofoil 5A damper/Fire Retardant Canvass connection/Unit mounted on cushy foot VibrationisolatOrs. 2500 CFM / 110 mm WC ESP / 6.5 TR / 8 Row Deep Coil / with pre filter & fine filter / Floor/Ceiling. mounted AHU / 32mm Double Skin AHU.
Supply of Air Handling Unit ( IOU) of Floor/ Ceiling Suspended AHU of 0.6 rem GI Double Skinned DX AHU with Al anodized thermal break frame structure injected with minimum 32 mm thick 40 kg/m3 PUF insulation; GI Panel shall be powder coated from both iner and outer side , the AHU shall comprising of: Mixing box / Anodized Aluminum Aerofoil Low leakage Fresh / Balancing / Exhaust Air Damper / Pre-Filter section with EU- 4 compliant Prefilters for Return and Fresh Air / Al finned 8 Row deep -13 FPI double skin sandwitch insulated removable 55 304 condensate drain pan / Fine filter EU 7 / fine filter section with EU 9 compliant / Fan section with Hi static best efficiency Plug Fan driven by suitable pole Eff-1 TEFC Motor with Drive Package / Al aerofoil 5A damper/Fire Retardant Canvass connection/Unit mounted on cushy foot VibrationisolatOrs. 3000 CFM / 110 mm WC ESP / 8.0 TR / 8 Row Deep Coil / with pre filter & fine filter / Floor/Ceiling. mounted AHU / 32mm Double Skin AHU.
Supply of Expansion Kit/ AHU KIT Supply of Expansion Kit, Communication PCB & Thermostat Supply of Electronic Type Expansion Kit, Communication PCB with Sensors, Corded Self Diagnostic Type Digital Thermostat, Controller, control box with internal wiring, AHU kit for each DX Type Units and other related accessories etc with connectivity to automation system ' for AN status, RUN status & Remote start / stop command (Bacnet/IP). For 2500 CFM F/M/CS AHU with 10 HP VRF ODU.
Supply of Expansion Kit/ AHU KIT Supply of Expansion Kit, Communication PCB & Thermostat Supply of Electronic Type Expansion Kit, Communication PCB with Sensors, Corded Self Diagnostic Type Digital Thermostat, Controller, control box with internal wiring, AHU kit for each DX Type Units and other related accessories etc with connectivity to automation system for A/M status, RUN status & Remote start / stop command (Bacnet/IP). For 3000 CFM F/M/CS AHU with 20 HP VRF ODU.
Supply of Ceiling Suspended Treated Fresh Air Unit. 400 CFM
Supply of Ceiling Suspended Treated Fresh Air Unit. 500 CFM
Installation, Testing & Commissioning of VRF Unit. 8 HP
Installation, Testing & Commissioning of VRF Unit. 10 HP
Installation, Testing & Commissioning of VRF Unit. 12 HP
Installation of Y joint/ Refnet
Installation, Testing & Commissioning of of Air Handing Unit ( IDU) Floor/ Ceiling Suspended AHU of 0.6 mm 51 Double Skinned DX AHU with Al anodized thermal break frame structure injected with minimum 32 mm thick 40 kg/m3 PUF insulation; GI Panel shall be powder coated from both iner and outer side , the AHU shall comprising of: Mixing box / Anodized'Aluminum Aerofoil Low leakage Fresh / Balancing / Exhaust Alr Damper / Pre-Filter section with EU- 4 compliant . Prefilters for Return and Fresh Air / Al finned 8 Row deep -13 FPI double skin sandwitch insulated removable SS 304 condensate drain pan / Fine filter EU 7 / fine filter section with EU 9 compliant / Fan section with Hi static best efficiency Plug Fan driven by suitable pole Eff-1 TEFC Motor with Drive Package / Al aerofoil SA damper/ Fire Retardant Canvass connection/Unit mounted on cushy foot Vibration Isolators. 2000 CFM /.110 mm WC ESP./ 6.5 TR / 8 Row Deep Coil / with pre filter & fine filter / Floor / Ceiling mounted AHU / 32mm Double Skin AHU.
Installation, Testing & Commissioning of of Air Handing Unit ( IDU) Floor/ Ceiling Suspended AHU of 0.6 mm 51 Double Skinned DX AHU with Al anodized thermal break frame structure injected with minimum 32 mm thick 40 kg/m3 PUF insulation; GI Panel shall be powder coated from both iner and outer side , the AHU shall comprising of: Mixing box / Anodized'Aluminum Aerofoil Low leakage Fresh / Balancing / Exhaust Alr Damper / Pre-Filter section with EU- 4 compliant . Prefilters for Return and Fresh Air / Al finned 8 Row deep -13 FPI double skin sandwitch insulated removable SS 304 condensate drain pan / Fine filter EU 7 / fine filter section with EU 9 compliant / Fan section with Hi static best efficiency Plug Fan driven by suitable pole Eff-1 TEFC Motor with Drive Package / Al aerofoil SA damper/ Fire Retardant Canvass connection/Unit mounted on cushy foot Vibration Isolators. 2300 CFM / 110 mm WC ESP / 8.0 TR / 8 Row Deep Coil / with pre filter & fine filter / Floor/Ceiling mounted AHU / 32mm Double Skin AHU. .
Installation Testing & Commissioning of AHU kit for 10 HP VRF ODU unit
Installation Testing & Commissioning of AHU kit for 12 HP VRF ODU unit
Supply Refrigerant R-410a for Top up in VRF system
Supply SITC of Refrigerant Piping with 19/13 mm thick' nitril rubber insulation Suction line with Nitrile rubber insulation
Supply SITC of Refrigerant Piping with 19/13 mm thick' nitril rubber insulation Liquid line with Nitrile rubber insulation
Supply Drain Piping HDPE Drain piping 32mm with insulation
SUPPLY & MODIFICATION OF DUCT WORK : AIR-DISTRIBUTION Supply and installation of Aluminum , site fabricated rectangular ducts, complete with Silicon Sealant joints with necessary supports using thread roads and anchor bolts. 22 SWG
Supplying of ACCOUSTIC INSULATION SITC of Open cell nitril rubber with 15mm thick
Supplying of THERMAL INSULATIONS OF THE DUCT WITH 13 MM NITRIL RUBBER 13 MM thick nitril rubber
Supplying of AIR TERMINATION SYSTEM Supply & Fixing of Al extruded powder coated Return Air Grill / Diffuser without Volume Control damper & necessary supporting arrangment
Supplying of SITC OF STRIP HEATER Strip Heater duct mounted for AHUs with necessary control device Termostat, Hundistat and Airstat for controlling RH.
Supplying of CONTROL PANEL Contro Panel for AHU motor with Interlocking arrangement with Strip heater
Supply, installation testing and of Laminar Flow Units (LFU) with duly paited by eposy paint comprising of Terminal EU 13 HEPA Filters of 99.997% Efficiency down to 0.3 Micron particle size installed in zero leakage frame with perforated plate type SA grille.
Supplying of Control Cables -Communication Cable 2C x .75 sqmm Sheilded copper cable in pvc conduit
Fire Fighting system Supply, Fixing, Testing & commissioning of Diesel Engine Driven Fire pump along with 12 V battery, battery charger, fuel tank, connection pipe, lug, etc.with 36 HP, LBS-065-200. (Make-Lubi)
Fire Fighting system- Supply, Fixing, Testing & commissioning of Electric Motor Driven 20 HP, 1700 LPM capacity of terrace Monoblock pump (Make-Lubi)
Fire Fighting system Supply, Fixing, Testing & commissioning of Electric Motor Driven 7.5 HP, 180 LPM capacity of terrace Monoblock pump (Make-Lubi)
Fire Fighting system Supply, Fixing, Testing & commissioning of Electric Motor Driven 5 HP, 450 LPM capacity of terrace Monoblock pump (Make-Lubi)
ANUPAM NIRMAN PVT. LTD.
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid