REPAIRS AND MAINT OF HT LT OH LINES UG CABLES TRANSFORMERS VCBs GODs LT PANEL MCCBs ACBs CHANGE OVER AND RENEWAL OF EARTHING WITH REPAIRS TO ACs AND ALLIED WORKS AT VRDE AHMEDNAGAR 06

Amount

Excavation in trenches, not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for poles, laying of electric cable and GI tubing (where provided for protection of cables) and getting out, trimming the sides, forming bottom surface to required level in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 centimetre complete all as specified and as directed.

Removing excavated material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

Material and labour for spread well dried sand cushioning in trenches complete all as specified and as directed. Note:- Thickness of sand cushioning shall be measured as punned thickness for the purpose of payment.

Dismantling of cross arms of MS channel or angle section etc.complete all as specified and as directed.

M &L for GI pipe 40mm dia light grade, for road crossing / on wall / on pole for cable protection including taking down/out old u/s GI pipe etc complete all as specified and as directed.

All as per above item No-6.00 but 50 mm dia complete all as specified and as directed.

All as per above item No-6.00 but 100 mm dia complete all as specified and as directed.

Supply and fix lightening arrester NON LINEAR RESISTER type, complete with all fittings, transmission classes, discharge capacity 65 Kilo amps suitable for 11 KV out door type complete including taking down old u/s LA complete all as specified and as directed.

Supply and fix in replacement pin type porcelain, vitreous, white brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 150mm height 150mm dia for 11KV grade complete all as specified and directed.

Supply and fix in replacement disc type insulator, porcelain, vitreous, white, brown or green 145 mm height and 255 mm dia ball and socket type single disc assembly for tension with tension clamp for conductor working pressure 11 KV grade complete all as specified and as directed.

S & F in replacement post insulator 11 KV for DO FUSE/ AIR BRAKE ISSOLATING switch complete all as specified and as directed.

Supply and fixing in replacement LT Pin type, porcelain, vitreous, white, brown or green insulator including one galvanized mild steel spindle, two galvanized iron washers and one galvanized iron nut, 100 mm height 65 mm dia for 1100 volt grade complete all as specified and as directed.

Supply and fixing in replacement shackle type, porcelain, insulator for working pressure 1100 volt with hardware fitting bolt, washers, nuts etc height 100mm dia 115 mm complete all as specified and as directed.

Supply, fabricating and fixing in repair mild steel cross arms bracings supports, D-clamps, back plates, clamps fabricated from structural steel section such as angle iron, channel, plate and flats etc including bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size including two coats of synthetic aluminium paint over a coat of red oxide primer after preparation of steel surface complete all as specified and as directed.

M & L for taking out all elect connections from LT panel and taking out the cable loop of any size of cable & checking the cable thoroughly including cleaning, cutting & removing the defective portion including provide new Alu lugs and re-fixing the cable in LT panel and relaying cable loop properly and testing complete all as specified and directed. Note : Cost of Alu lugs, labour for earth work deemed to be included in the quoted rate.

Repairs to LT panel board any size outdoor/indoor type by removing the U/S door hinges and S&F new door hinges of suitable size by welding including levelling the door by removing bends/dents and aligning the door for proper closing complete all as specified and directed by Engr-in-Charge.

Supply & Laying 50 mm outside dia double wall corrugated pipe (DWC) of HDPE ISI Mark for enclosing cable below ground / road surface, to a required depth, including suitable size coplers for jointing of pipe all as per site requirement complete all as specified and as directed.

Supply & Laying 75 mm outside dia double wall corrugated pipe (DWC) of HDPE ISI Mark for enclosing cable below ground / road surface, to a required depth, including suitable size coplers for jointing of pipe all as per site requirement complete all as specified and as directed.

M&L for painting with spray pump of LT panel Indoor/outdoor any size any type from outside with two coat of synthetic enamelled paint (colour approved by Engr-in-Charge) over a coat of red oxide and cleaning of LT panel MCCB's terminals and LT panel from inside with air blower and waste cloths complete all as specified and directed

M&L for painting to LT MS tubular Pole 8.5/9 mtr long with two coats of synthetic enamelled aluminium paint over prepared surfaces complete all as specified and directed.

M&L for painting to HT MS tubular pole 11 Mtr long with two coats of synthetic enamelled aluminium paint incl cross arms (for single pole), clamps etc. complete all as specified and directed.

M&L for painting of HT 11 Mtr long 6 pole structure with two coat of synthetic enamelled aluminium paint including channel, clamps & accessories in erected position and 1.2 mtr height from ground level in alternate band of approved colour with synthetic enamel paint over prepared surfaces complete all as specified and as directed.

All as above item No - 23.00 but 4 Pole structure complete all as specified and as directed.

All as above item No - 23.00 but 2 Pole structure complete all as specified and as directed.

Taking down the existing defective LT UG cable of 4 sq mm x 2/3/3.5/4 core upto 70 sqmm x 3/3.5/4 core from trenches / pipes / pole all as specified and as directed.

All as per above item No - 26.00 but size 95 sqmm x 3.5 core upto 500 sqmm x 3.5 core complete all as specified and as directed.

Taking down the existing defective HT UG cable of 95 sqmm to 185 sqmm 3 core from trenches / pipes / pole complete all as specified and directed.

Supply, laying, jointing and testing of under ground electric cable, XLPE sheathed HT 11000 volts, grade, heavy duty, armoured with aluminium multi stranded conductor cross sectional area of cable 95 Sqmm, 3 core conforming to IS laid in trenches, under floor, through the roads fixed along wall/pole/GI pipe complete all as specified and as directed.

Supply, laying, jointing and testing of under ground electric cable, XLPE sheathed LT 1100 volts, grade, heavy duty, armoured with aluminium multi stranded conductor cross sectional area of cable 500 Sqmm, 3.5 core conforming to IS laid in trenches, under floor, through the roads fixed along wall/pole/GI pipe with proper clamps, lugs complete all as specified and as directed.

All as per above item No-30.00 but of 240 Sqmm, 3.5 core complete all as specified and as directed.

All as per above item No-30.00 but of 95 Sqmm, 3.5 core complete all as specified and as directed.

All as per above item No-30.00 but of 70 Sqmm, 3.5 core complete all as specified and as directed.

All as per above item No-30.00 but of 35 Sqmm, 3.5 core complete all as specified and as directed.

All as per above item No-30.00 but of 25 Sqmm, 4 core complete all as specified and as directed.

All as per above item No-30.00 but of 16 Sqmm, 4 core complete all as specified and as directed..

All as per above item No-30.00 but of 10 Sqmm, 4 core complete all as specified and as directed.

All as per above item No-30.00 but of 6 Sqmm, 2 core complete all as specified and as directed.

Supply & laying half round concrete hume pipe of 150mm inner dia and 25mm thick & 1 meter length complete all as specified and as directed.

Material and labour for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in base and surrounding the pole and stay complete all as specified and as directed.

Material and Labour for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in foundation for feeder pillars, LT Panel and coping of poles including necessary form work and fair finished to exposed surfaces without using extra cement complete all as specified and as directed.

Supply and fix in replacement of switch air break gang operated triple pole mechanically operated mounted on HT insulator (09 insulator , Vertical type) and Mild steel frame with operating mechanism worked from ground level including operating rod for current rating up to 400 amps, 11000 volts complete with 6 lever pad locking arrangements, MS Clamp, nuts, bolts and washers etc including two coats of aluminium paint over a coat of red oxide primer on MS work complete all as specified and directed.

Supply and fixing in replacement drop out fuses HT, 11 KV Triple pole, rating 100 amps with base frame and insulator complete all as specified and as directed.

Supply & fixing Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for LT, 20x15cm size complete all as specified and as directed.

All as per item No. 44.00 above but for HT, 25x20cm size complete all as specified and as directed.

Material and labours earthings complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick, buried directly in ground (Earth pit not less than 2.25 metres deep below ground level) , surrounded from all direction with charcoal dust and salt in layers, the top edge of the earth plate not less than 1.5 metre below ground level, connected to galvanized iron strip 32×6mm as earthing lead and 40 mm bore GI pipe light grade for protection of GI strip. fixed by means of bolts, nuts and washers of galvanized iron and connected to earth test point and equipment and testing on completion including excavation and earthwork in any type of soil, PCC chamber in 1 :2:4 using 20 mm graded stone aggregate, CI cover, 20 mm GI pipe light grade for watering, funnel, wire mesh complete all as specified and shown on electrical plate No 5 of MES Schedule Part ‘I’( 1991) including taking out old u/s earthing all as directed. Note - Cost of GI Strip up to 7.5 RM is deemed to be included in the quoted rate complete all as specified and as directed.

Supply and fix in repairs Time switch daily dial 240 v AC Base mounting type complete all as specified and as directed.

Supply and fix in repairs Programmable time switch 24 Hrs, 240 volt complete complete all as specified and as directed.

Supply and fix in repairs Power contactor 3 pole, MNX 110 , 415 V 110 Amp complete all as specified and as directed.

Supply and fix in repairs Power contactor 3 pole, MNX 225 , 415 V 225 Amp complete all as specified and as directed.

Supply and fix in repairs Power contactor ML3 type, 415 V, 40 A complete all as specified and as directed.

Supply & Fix in repairs Power contactor FP, 415 volt, 16 Amps complete all as specified and as directed.

Supply & fix in repairs power control relay 3.2 to 5 Amps complete all as specified and as directed.,

Supply and fix in repairs MCB SPN 40 A, 230 volt. 'C' curve complete all as specified and as directed.

Supply and fix in repairs MCB TPN/FP 40 A, 415 volt. 'C' curve complete all as specified and as directed.

Supply and fix in repairs MCB TPN/FP 63 A, 415 volt. 'C' curve complete all as specified and as directed.

Supply and fix in repairs MCB TPN/FP 100 A, 415 volt. 'C' curve complete all as specified and as directed.

Supply and fix in repairs MCB TP 63 A, 415 volt. 'C' curve complete all as specified and as directed.

Supply and fixing in replacement MCCB, 630 Amps, FP 415 volt, 50 KA capacity with suitable terminals in existing/ new separate mounting panel including drilling hole, nut bolt and washers and making electrical connections complete all as specified and as directed.

Supply and fixing in replacement MCCB, 400 Amps, FP 415 volt, 36 KA capacity with suitable terminals in existing LT panel including drilling hole, nut bolt and washers and making electrical connections complete all as specified and as directed.

Supply and fixing in replacement MCCB, 250 Amps, FP 415 volt, 36 KA capacity with suitable terminals in existing LT panel including drilling hole, nut bolt and washers and making electrical connections complete all as specified and as directed.

All as per above item No-61.00 but 200 Amps, TP, 16 KA complete all as specified and as directed..

All as per above item No-61.00 but 100 Amps, TP, 16 KA complete all as specified and as directed..

Supply & fix heat shrink cable jointing kit for 1.1 KV grade cable for straight through joint kit complete with jointing material and accessories suitable for 2/3.5/4 core XLPE / PVC armoured Aluminium Conductor cable of size 16 Sqmm to 35 Sqmm complete all as specified and as directed. Note:- Earth work will be measured and paid separately.

All as per above item No-64.00 but suitable for size 50 Sqmm to 95 sqmm 3.5 Core complete all as specified and as directed.

Supply and fixing in replacement of heat shrinkable end termination out door joint kit of 3 core 95 sqmm suitable for 11000 volt with accessories and testing complete all as specified and as directed by Engineer in charge.

All as per above item No-66.00 but suitable for size 120 to 185 Sqmm complete all as specified and as directed.

Supply and fixing in replacement of heat shrinkable straight through joint kit of UG cable 3 core 95 sqmm to 185 sqmm suitable for 11000 volt with accessories and testing complete all as specified and as directed by Engineer in charge. Note:- Earth work will be measured and paid separately.

Dismantling of old/rusted aluminium conductor steel reinforced of any size and removing the same from site of work all as specified and directed by Engineer-in-Charge.

Material and labour for aluminium conductor steel reinforced [ACSR] straining properly on insulators and binding with aluminium tape/binding wire, connectors, jumpers etc on required places complete all as directed by Engr-in-charge.

Material and labour for painting of transformer complete with radiator of capacity up to 500 KVA, 11/.433 KV outdoor type with two coat spray painting with synthetic enamelled gray paint after preparation of transformer surface complete all as specified and directed.

Restringing of existing ACSR conductor of LT/HT OH line on PCC/steel tubular poles properly on insulators and rebinding with aluminium binding wire connectors, jumpers etc complete to the entire satisfaction of Engineer-in-Charge.

Disconnecting and dismantling the ACB breaker rating 400 to 800 Amps make Crompton Greaves/C&S/ L&T by carrying out repair/ servicing , checking and renewing the defective shunt trip coil & UV trip 415 V AC , checking and rectifying the defective CTs and rectifying the mechanism operation including spring charge system, reinstalling the same in the panel and providing necessary line and connections all as directed by Engineer-in-charge.

Surface excavation not exceeding 30 cm deep in hard and dense soil and getting out green vegetation, roots, bushes, etc surrounding of pole structure / substations / pump house as directed by Engr-in- charge.

Material and labour for cutting of bituminous road / floor for laying of pipe / cables not exceeding 20cm wide and not exceeding 30 cm deep including refilling with material and, watering well ramming / compacting and making good with premixed bituminous macadam, 100mm thick complete all as specified and directed by Engr-in-Charge.

Servicing and alignment of existing 11 KV GOD by cleaning the contact / pin insulator with CTC & applying the petroleum jelly at the contact, replacement of jumpers as required ,adjusting the down rod links for smooth operation including replacing the rusted/ corroded bolts & nuts and defective insulator / contacts /copper strip of GOD as required at site complete all as specified and as directed. Note :- Insulator /contacts /copper strip shall be measured and paid under relevant items.

Supply only Male / Moving contact (set of 3 Nos ) complete all as specified and as directed.

Supply only Female / Fixed contact (set of 3 Nos ) complete all as specified and as directed.

Supply only Copper tinned strip (set of 3 Nos ) complete all as specified and as directed.

Cutting, trimming and vending tree branches falling on overhead head lines after arranging electrical shutdown from department or MSEB including taking all precautions while working on lines complete all as specified and as directed. Note:- (i) The length of span between two poles shall be measured in which trees are falling on overhead electric conductors. (ii) Required T & P will be arranged by the contractor at his own cost.

Supply and fixing new jumper connection at cut point on HT over head line with suitable size of ASCR conductor 6 / 1 x 3.00 mm (ferret/weasel) PG Clamps, lugs, alkathine sleaves,galvanised nut and bolts complete of required length not exceeding 3 mtr including testing on completion and including dismantling of old u/s jumper complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement of 3 phase LED voltmeter Cl 0.5 with suitable accessories and fixing arrangements complete all as specified and as directed.

S&F in replacement of 3 phase LED Ampmeter Cl 0.5 with CTs and suitable accessories and fixing arrangements complete all as specified and as directed..

Supply & fix in repair LT insulation bushings 433V of suitable size for outdoor type transformer of capacity up to 160 KVA complete all as specified and as directed.

All as per above item No- 84.00 but above 160 KVA up to 500 KVA complete all as specified and as directed.

Supply & fix in repair HT insulation bushings 11 KV of suitable size for outdoor type transformer of capacities up to 160 KVA complete all as specified and as directed.

All as per above item No- 86.00 but above 160 KVA up to 500 KVA complete all as specified and as directed.

Supply & fix in repair brass stud (for LT 433V side)of suitable size complete with one chuck nut, two nuts, washers and rubber seal, all as per sample for outdoor type transformer of the capacity up to 160KVA complete all as specified and as directed.

All as per above item No- 88.00 above but 160 KVA up to 500 KVA complete all as specified and as directed.

Supply & fix in repair brass stud (for HT 11 KV side) of suitable size complete with one chuck nut, two nuts, washers and rubber seal, all as per sample for outdoor type transformer of the capacity up to 160KVA complete all as specified and as directed.

All as per above item No- 90.00 above but 160 KVA up to 500 KVA complete all as specified and as directed.

M&L for disconnecting the transformer of capacity 50 KVA to 100 KVA and taking out the complete HT/LT cable/ Jumper connections and terminal box by removing all nuts/bolts/gasket etc.. Cleaning the HT and LT bushings and terminals etc. and inspecting for any damaged winding or any loose connections, leakages of oil, tightening the clamps, and checking the winding for its proper functioning and reassembling by replacing a new gaskets of required size and shapes including draining, refilling of transformer oil and reconnecting HT and LT connections and testing & commissioning complete all as specified. Note : (i ) HT/LT bushings will be measured and paid separately under relevant item.

All as per above item No-92.00 but capacity 150 to 200 KVA complete all as specified and as directed.

All as per above item No-92.00 but capacity 250 to 315 KVA complete all as specified and as directed.

All as per above item No-92.00 but capacity 400 to 500 KVA complete all as specified and as directed.

M&L for refilling / top up the transformer oil low viscosity conf to IS 335:1993 filtered of all as directed and sample of oil duly tested for di elect strength not less than 45 KV at 2.5 mm gap complete all as specified and as directed.

M&L for filtration/ dehydration of transformer oil ON LINE through mobile stream line transformer plant at site and testing of sample of transformer oil before and after filtration for di electric strength up to 45 KV at 2.5 mm electrode gap complete all as specified and as directed.

Opening of transformer and taking out old unserviceable tap changer and supply & installed new tap changer complete suitable for transformer outdoor type capacity up to 500 KVA complete all as specified and as directed.

Disconnecting all the electrical connections from H.T.and L.T. side of unserviceable transformer of capacity up to 160 KVA i.e. Jumpers/cable from the cable end box or bushings & earthing terminal of the transformers, loading and unloading of transformer & transportation by vehicle/crane from substation to the repairing workshop including reinstallation, commissioning and testing complete all as specified and as directed.

Disconnecting all the electrical connections from H.T.and L.T. side of unserviceable transformer of cap above 160 KVA to 500 KVA i.e. Jumpers/cable from the cable end box or bushings & earthing terminal of the transformers, loading and unloading of transformer & transportation by vehicle/crane from substation to the repairing workshop including reinstallation, commissioning and testing complete all as specified and as directed.

Opening the transformer cover rating up to 160 KVA along with the conservator by removing the nut bolts then after removing the internal HT.& LT connections by taking them out by removing studs, bushings, taking out the core-winding assembly out of the tank of transformer having ratio 11/0.433KV, draining & decanting of transformer oil and cleaning of sludge deposited in the tank with CTC for the transformer. Heating of core winding assembly in hot chamber for 48 hours and remove all the moisture present in it , removal of leakage of tank if any by welding, refilling transformer oil in to the tank after dehydration / filtration and checking of dielectric strength of oil , after putting the core-winding assembly into the tank, reassembling making the internal H.T. & L.T. connections by fixing the studs, bushings, fitting the top cover by replacing cork sheet gasket along with conservator, testing the transformer in the workshop duly filled with oil, all as directed by Engineer-in-charge. Note : U/S items required for repairs shall be measured and paid under relevant item of this schedule. Transformer oil if required with die electric strength not less than 40KV either new or filtered shall be filled and shall be measured and paid separately under respective item.

All as per above item No-101.00 above but of capacity above 160 KVA to 500 KVA complete all as specified and as directed.

Supply only super enamelled copper winding wire / strip of any size for HT coils of transformers complete all as specified and as directed.

Supply only copper winding strip of any size for LT coils of transformers including providing insulation all as required complete all as specified and as directed.

Reconditioning of LT coil of copper wound transformer by turning the old paper insulations, straightening the entire LT Strip providing new paper insulations of superior quality and making coil of suitable design as original all as specified and directed by Engr-in-Charge.

Supply and fix in replacement oil temperature gauge meter suitable for transformer up to 500 KVA transformer complete all as specified and as directed..

M & L for replacement of breather assembly of transparent plastic body with top and bottom portion pressed with metallic cover, filled with silica jel blue in colour and suitable for pipe entry of 15/20/25mm dia as per the site requirement, complete all as specified and as directed by Engineer-in-Charge.

Supply & fix in replacement LED 10 W decorative garden light LED bollard in round/squared shaped with opel acrylic diffuser and aluminium reflector IP 65 protection includes necessary PCC cylinderical foundation with PCC 1:2:4 height not less than 30cm and dia 25cm above from ground for fixing of light fitting including connector and necessary electrical connections etc. all as specified and directed.

Supply and fixing in replacement street light mounting bracket made out of GI pipe 40 mm dia 'medium Grade' not less than with 0.75 m. long in any shape with 2 nos of clamps made out of MS flat of size 40 x5 mm and nuts and bolts all as directed by Engr-in- Charge.

Supply, installation, testing and commissioning in replacement of street light panel outdoor type on wall/pole comprising with Digital 24 Hrs timer-01 Nos, contactor 65 Amps, TP -01 Nos, MCB TPN 63 Amps -01 Nos copmlete with necessary electrical connections all as directed by EIC.

Supply, installation, testing and commissioning in replacement of Street light panel outdoor type for Digital 24 Hrs time switch with 32 Amps 3 phase 415 Volt contactor, suitable relay and 40 Amps SPN MCB for automatic switch on and switch off all as directed by EIC.

Supply & fixing in replacement Steel tubular swaged poles of 9.00 mtr height complete with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP-22 including dismentling of old u/s pole of any type all as specified and as directed. NOTE:- Excavation & earth / concrete work shall be measured separately.

Supply and fixing in replacement of unserviceable existing HPSV/HPMV/tube light fitting of any wattage on existing poles with LED security light 60 W IP 66 complete all as specifed and directed by Engineer-in-charge.

Supply and fixing in replacement of unserviceable existing HPSV/HPMV/tube light fitting of any wattage on existing poles with LED security light 90 W IP 66 complete all as specifed and directed by Engineer-in-charge.

Supply and fixing in replacement of unserviceable existing HPSV/HPMV/tube light /LED lamp fitting of any wattage on existing poles/High mast with LED flood light 30 W IP 66 pressure die cast aluminium housing for large area lighting complete including suitable MS clamps, nuts & botls with necessary electrical connection all as specified & directed.

Supply and fixing in replacement of unserviceable existing HPSV/HPMV/tube light /LED lamp fitting of any wattage on existing poles/High mast with LED flood light 100W IP 66 pressure die cast aluminium housing for large area lighting complete including suitable MS clamps, nuts & botls with necessary electrical connection all as directed by EIC.

Supply and fixing in replacement of unserviceable existing HPSV/HPMV/tube light /LED lamp fitting of any wattage on existing poles/High mast with LED flood light 200 to 210 W IP 66 pressure die cast aluminium housing for large area lighting complete including suitable MS clamps, nuts & botls with necessary electrical connection all as directed by EIC.

S & F in repair pole mounting boxes( DB) factory made of FRP heavy duty internal dimention not less than 155x155x100mm comprising with the following :- (a) Three phase copper connector on porcelain insulators complete including lugs and suitable size of MS clamps as per site requirement - 02 Nos, nut and bolts etc.all as directed by Engr In Charge.

Supply & fix in replacement of unserviceable existing HPMV/HPSV post top lantern with LED 40 to 45 W decorative post top LED, made in cast aluminium with decorative opal polycarbonate diffuser with IP 65 protection including minor fabrication on top of existing pole according to luminaire dia all as directed and specified.

Supply & fix in replacement of unserviceable existing LED Solar street light fitting 36 Watt including galvanized steel pole in built, lithium ion battery, solar panel, charge controller with dusk down sensor complete all as specified and as directed. Note : Excavation & earth work shall be measured and paid separately.

M &L for GI pipe 40mm bore "Medium grade" for mounting of post top lantern, including cutting, fabricating and welding of suitable length all as directed by Engr-in-Charge.

Supply and fix in replacement electronic driver & panel for LED street light fitting 45/60/90 Watt complete all as directed by EIC.

Supply and fix in replacement electronic driver & panel for LED street light /Panel light fitting 36 to 45 Watt complete all as specified and as directed.

Supply & fix battery 12 V 150Ah for DG set complete all as specified and as directed.

Supply & fix battery 12V 100Ah for DG set complete all as specified and as directed.

Supply & fix battery charging unit 24 V 10A Battery charger complete all as directed by EIC.

Supply and fix in replacement of 1 Sqmm 3 core PVC insulated stranded copper cable from pole junction box to fitting all as directed by EIC.

Dismantling the fuel injection pump assembly for overhauling and repairing by replacing of worn out parts such as gasket diafarm etc complete all as directed and calibration of FIP and refixing the same having capacity 250 KVA suitable for kirloskar DG set as directed by EIC.

Ditto- all as per item No. 128.00 above but of capacity 160 KVA DG set complete all as specified and as directed.

Supply and replace the injector nozzles for 160 KVA to 250 KVA DG set suitable for Kirloskar Engine all as directed.

Supply and replace water pump assembly suitable for 250 KVA capacity suitable for Kirloskar DG Set complete all as specified and as directed.

Ditto all as per item No. 131.00 above but suitable for capacity 160 KVA for Kirloskar Engine complete all as specified and as directed.

Supply and replace V fan belt heavy duty for water pump of capacity 160 KVA to 250 KVA Kirloskar Engine complete all as specified and as directed.

S & F V fan belt for alternator of capacity 160 to 250 KVA DG Set complete all as specified and as directed.

M&L for carrying out the servicing of DG set make Kirloskar complete all as per manufacturer's instructions and all as directed by the Engineer-in-Charge by replacement of the following parts of 250 KVA Capacity DG Set including carrying out minor addition/alternation and supply and fixing the parts for smooth functioning of DG Sets at Tech area. MAKE : Kirloskar [a] Element fuel filter with 'O' ring - 2 Nos [b] All Oil filter element [c] Element air cleaner (Inner & Outer)- 1 Nos. [d] Checking and correcting up of water pump for excess play. [e] Cleaning and tightening of all electrical connections of DG sets upto the entire satisfaction of the Engr-in-Charge. [f] Cleaning of entire DG sets with proper cleaning material upto the entire satisfaction of the Engr-in-Charge. [g] Checking and tighting inlet & exhaust manifold bolts & nuts. [h) Taking down and cleaning and servicing of radiator from inside and outside throughly with cleaning solution and refixing the radiator assembly properly. [j] Replacing the radiator hose pipe with suitable size with clamps. [k] Checking and making good vibration dampner. [l] Checking and correcting of inlet/exhaust valve, valve guide with grinding of valve and grinding of injector Nozzles and cleaning of head and calibration of rocker arm and refixing with head gasket.

Ditto- all as per item No.135.00 above but DG set capacity 160 KVA. Make : Kirloskar.

Ditto- all as per item No.135.00 above but DG set capacity 40 KVA to 75 KVA. Make : Cummins

Ditto- all as per item No.135.00 above but DG set capacity 25 KVA to 30 KVA. Make : Cummins Note for item No 135.00 to 138.00 above : Servicing and all above mentioned jobs will be carried out by authorised manufacturer's representative only to the entire satisfaction of the Engineer-in-Charge. Engine Oil, coolent will be measured and paid as separate item.

M&L for Repair to Radiator assy by disconnecting the radiator from engine frame and servicing/cleaning with acid and brazing where required to stop leaking tubes/joints etc. cleaning fins and refixing the same for DG set 160 KVA to 250 KVA all as directed by Engineer-in-Charge.

Repairs and overhauling of self starter complete including replacement of all worn out parts, bushing contact assembly complete after dismantling and refixing the same after repairs all as specified and directed by the Engineer-in-Charge

Supply and replace the battery copper lead of 70 Sq mm size having 1.5 M length with suitable terminal complete all as directed.

Ditto- all as per item No. 141.00 above but having 30 cm length all as directed by EIC.

Supply and filling in sump / topping up engine oil, multi grade 15w/40 in engine or replacement of engine oil all as directed.

Supply and filling electrolyte of suitable Sp gravity for lead acid batteries in sealed containers all as diected by EIC.

Supply & fill coolent of DG Set all as directed by EIC.

Supply and fix in repair fuel pipe steel braided, steel stranded with benzo bolts and washers etc complete of length 30 cm long all as directed by EIC.

Supply and fix in repair fuel pipe steel braded, steel stranded with benzo bolts and washers etc complete of length 45 cm long all as directed by EIC.

Supply and fix in repair fuel pipe steel braded, steel stranded with benzo bolts and washers etc complete of length 60 cm long all as directed by EIC.

Supply and fix in repair fuel level indicator transparent PVC pipe of suitable dia for fuel level in tank all as directed by EIC.

Supply and fix in repair solenoid switch vertical/ horizontal type capacity upto 160 KVA DG set all as directed by EIC.

Supplying, installation, testing & commissioning of cubical type LT panel outdoor type ( IP 65 protection ) CPRI approved, suitable for 415 V, 3 phase, 4 wire, 50 HZ AC supply, comprising of the followings :- (a) Enclosure ( IP 65 protection) fabricated in compartmentalized design from CRCA sheet steel of 3.15mm thick for frame work and 4mm thick covers for gland plates, i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade having 850 Amp capacity extensible type TPN copper bus bars of high condutivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 sec, bottom base channel of MS not less than 100mm x 50 mmx 5 mm fabrication shall be done in transpotable sections, entire enclosure shall have a common copper earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to switch gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required at site including taking down old u/s panel of any description all as directed. (b) Bus Chamber : 850 Amps rated Copper Busbar - 04 Nos (c) INCOMMING : MCCB 630 Amps , 4 Pole, 415 volt, 36 kA with thermal magnetic release - 01 Nos (d) OUTGOING : (i) MCCB 400 Amps, 4 Pole, 415 volt, 36 kA with thermal megnetic release.-01 No (ii) MCCB 350 Amps, 4 Pole, 415 volt, 36 kA with thermal megnetic release.- 01 No (iii) MCCB 125 Amps, 3 Pole, 415 volt, 16 kA with thermal megnetic release.-02 Nos (iv) MCCB FP 63 Amps-01 No (v) 3 Phase LED Volt meter Cl-0.5 (vi) 3 phase LEDAmpmeter Cl-0.5 with CT's. (vii) Indication LED set of three (01 Set for Incomming and 06 set for outgoing) NOTE:- Cost of cable glands, MCCB spreader terminals, cable lugs etc shall deemed to be included in quoted rate. Panel shall be spacious for easy maintenance and cable connections etc.

Supplying, installation, testing & commissioning of cubical type LT panel outdoor type ( IP 65 protection ) CPRI approved, suitable for 415 V , 3 phase, 4 wire, 50 HZ AC supply, comprising of the followings :- (a) Enclosure ( IP 65 protection) fabricated in compartmentalized design from CRCA sheet steel of 3.15mm thick for frame work and 4mm thick covers for gland plates, i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade having 850 Amp capacity extensible type TPN copper bus bars of high condutivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 sec, bottom base channel of MS not less than 100mm x 50 mmx 5 mm fabrication shall be done in transpotable sections, entire enclosure shall have a common copper earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to switch gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required at site including taking down old u/s panel of any description all as directed. (b) Bus Chamber : 850 Amps rated Copper Busbar - 04 Nos (c) INCOMMING : MCCB 630 Amps , 4 Pole, 415 volt, 36 kA with thermal magnetic release - 01 Nos (d) OUTGOING : (i) MCCB 500 Amps, 4 Pole, 415 volt, 36 kA with thermal megnetic release.-01 No (ii) MCCB 125 Amps, 3 Pole, 415 volt, 16 kA with thermal megnetic release.-02 Nos (iii) MCCB FP 63 Amps-01 No (iv) 3 Phase LED Volt meter Cl-0.5 (v) 3 phase LEDAmpmeter Cl-0.5 with CT's (vi) Indication LED set of three for incomer & outgoing NOTE:- Cost of cable glands, MCCB spreader terminals, cable lugs etc shall deemed to be included in quoted rate. Panel shall be spacious for easy maintenance and cable connections etc.

Supplying, installation, testing & commissioning of cubical type LT panel outdoor type ( IP 65 protection ) CPRI approved, suitable for 415 V, 3 phase, 4 wire, 50 HZ AC supply, comprising of the followings :- (a) Enclosure ( IP 65 protection) fabricated in compartmentalized design from CRCA sheet steel of 3.15mm thick for frame work and 4mm thick covers for gland plates, I/C cleaning & finishing complete with 7 tank process for powder coating in approved shade having 850 Amp capacity extensible type TPN copper bus bars of high condutivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 sec, bottom base channel of MS not less than 100mm x 50 mmx 5 mm fabrication shall be done in transpotable sections, entire enclosure shall have a common copper earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to switch gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required at site including taking down old u/s panel of any description all as directed. (b) Bus Chamber : 1200 Amps rated Copper Busbar - 04 Nos (c) INCOMMING : ACB 4 Pole, 415 V, with Thermal Magnetic Release (Manual Fixed type) of capacity 800 Amps , 4 Pole, 415 volt, 36 kA - 01 Nos (d) OUTGOING : (i) MCCB 400 Amps, 4 Pole, 415 volt, 36 kA with thermal megnetic release.-02 No (ii) MCCB 630 Amps, 4 Pole, 415 volt, 50 kA with thermal megnetic release.- 01 No (iii) 3 Phase LED Volt meter Cl-0.5 (iv) 3 phase LEDAmpmeter Cl-0.5 with CT's (v) Indication LED set of three (01 Set for Incomming and 03 set for outgoing) NOTE:- Cost of cable glands, MCCB spreader terminals, cable lugs etc shall deemed to be included in quoted rate. Panel shall be spacious for easy maintenance and cable connections etc.

Dismantling and replacement of old LT panel and supply, installation, testing and commissioning of new LT panel board (CPRI Approved) made out of 3.15mm thick CRCA sheet steel enclosure OUTDOOR cubical type, double door with aprons, dust, vermin, weather proof duly powder coated with seven tank process and all as per IE rules,mounted on angle iron of size 50x50x6mm with two coats of black synthetic enamel paint over a coat of red oxide primer and height from ground level not less than 50 Cm including grouting with PCC 1:4:8 type D2 40 mm graded stonre aggregate including necessary excavation and earth work complete with necessary compartments, fitted with 4 Nos TPN of aluminium bus bar 200 Amps with colour code sleeves mounted on porcelain/SMsC/DMC insulators, including internal control wiring with PVC insulated copper wire of suitable size and panel shall have comprise/including of following items :- (a) Bus Chamber : (i) Aluminium Busbar 200 Amps rated - 04 Nos (b) INCOMING :- (i) MCCB 100 Amps, 4 Pole, 415 volt, 18 kA with thermal megnetic release - 01 Nos (c) OUTGOING :- (i) MCCB 63 Amps, 3 Pole, 415 volt, 18 kA with thermal megnetic release - 02 Nos (ii) Digital 24 Hrs time switch with 65 Amps 3 phase 415 Volt contactor, suitable relay and 63 Amps TPN MCB for automatic switch on and switch off of street lights complete - 01 Nos (iii) Indication LED set of three (RYB) with integral circuit 01 Set for Incomming and 02 set for outgoing - 03 Set (iv) 3 Phase LED Voltmeter - 01 Nos (iv) 3 PhaseLED Amp Meter with CT's. - 01 Set (v) Spare Space with mounting rail for MCB TPN -02 Nos. Note :- Cost of Cable glands, MCCB spreader terminals, cable lugs etc is deemed to be included in the quoted rate. Panel should be spacious for easy maintenance and cable connections etc.

Comprehensive Maintenance (Preventive and breakdown) of electrically operated travelling (EOT) crane of 1 Ton capacity (1No.), floor operated, comprising of hoist motor, micro motor, long travel motor, cross travel motor, gear box, control panel and other connected accessories installed at foundry shop Make RASI & Co. Sl No 1005/91 all as directed.

All as per above item No-155.00 but of capacity 2 Ton installed at :- (a) VEM workshop, Make - Cranex Ltd Sl No. 8701

(b) Extn to M/C shop, Make - Eltech Sl. No. 1710

(c) IC Engine lab Make Cranex Ltd Sl No. 8626

(d) TIC Bldg. NCAT, Make - Electro Technique P Ltd.

(e) IC Engine Lab Make - Dinesh S.No. 701

(f) IC Engine lab Make - Dinesh S. No. 702

(g) IC Engine lab Make - Dinesh S. No. 703

All as per above item No-155.00 but of capacity 5 Ton installed at :- (a) Machine shop, Make - Cranex Ltd Sl. No. 8803

(b) Fabrication shop, Make - Cranex Ltd Sl. No. 8702

(c) MMG shop Make - Dinesh Sl. No. 608

All as per above item No-155.00 but of capacity 15 Ton installed at ICV shop. Make - Dinesh Enterprises, Sl No. 304

All as per above item No-155.00 but of capacity 15 Ton installed at UGV shop at NCAT Make REMI

M&L for 100% load testing of EOT crane of following capacity for deflection test :- (a) 1 (one) Ton

(b) 2 (Two) Ton

(c) 5 (Five) Ton

(d) 15 (Fifteen) Ton Note for item No. 159.00 to 159.03 above :- (i) Cost is deemed to include 100% load test for deflection test once in contract period but within six months from the commencement of contract. Load for testing will be arranged by the contractor at his own cost and no separate payment would be done in this regard. Test will be carried out with 100% load for LT, CT and Hoisting at normal speed and micro motion and for deflection. Test certificate for load test will be submitted separately apart from Form 12. (ii) Test would be done in the presence of competent authority (appointed by Directorate of Industrial safety and Health, Govt of Maharashtra or equivalent) for testing of cranes and certificate (Form 12 Prescribed for examination of lifting machines, ropes and tackles) to this effect would be rendered regarding stability of crane.

Supply only HRC fuse contacts complete with base in re-placement of old unsv from 5 to 16 Amps capacity all as directed.

Supply only HRC fuse contacts complete with base in re-placement of old unsv from 20A to 40 Amps capacity all as directed.

Supply only brake shoe assembly complete (Thruster type) with lining set suitable for main hoist upto 5 ton cap all as directed.

Supply and fix for replacing the existing unsv Contactor 3 phase 415 Volts, of BCH/L&T/C&S/Siemens make suitable model/Voltage as required at site of following sizes:- (a) 70 Amps Type ML 4.

(b) 40 Amps Type ML 3.

(c) 30 Amps Type ML 2.

(d) 16 Amps Type ML 1.

(e) 12 Amps Type ML 0.

Supply only in repairs Over load electro pnematic relay contactor mounting type make: Siemens/BCH as required at site of the following capacity all as directed by EIC. (a) 8 – 12 Amps

(b) 5 – 8 Amps

(c) 2 – 3 Amps

(d) 1.25 – 2 Amps

Supply only of Hydrulic/ gear oil for upto 15 ton capacity of cranes all as directed by Engineer-in-charge.

Supply only gasket for gear box /hoist for 1 ton capacity of crane all as directed.

Supply only gasket for gear box /hoist for 2 ton capacity of crane all as directed.

Supply only gasket for gear box /hoist for 5 ton capacity of crane all as directed.

Supply only gasket for gear box /hoist for 15 ton capacity of crane all as directed.

Supply only brake liner unit 100 mm dia all as directed.

Supply only brake liner unit 150 mm dia all as directed.

Supply only limit switch two way shut type 16 Amp all as directed.

Supply only carbon brush sqare for micro clutch all as directed.

Supply only pendant push buttons all as directed.

Supply only pendant indicators all as directed.

Supply only Electromagnetic brake coil 300VA Capacity all as directed.

Supply and fix in repairs copper flexible multicore cable of size 1.5 sqmm x 19 core all as directed.

Supply & fix in repairs Time delay relay electro pnumatic with 2 NO+2 NC,PN type, 220 volts all as directed.

Supply and fix in replacement of unsv single phase preventor 415V, 3 Phase all as directed.

Supply and fix in replacement steel wire rope for upto 5 ton capacity of crane of size 12 mm dia IPS grade upto 1960 N/mm2 all as directed by Engineer -in-charge .

Supply and fix 2.5 sqmm 4 core copper conductor 1100 V grade as in submain wiring includind PVC conduit of suitable size complete all as specified and as directed.

Supply and spread in layers, stones aggregate for loose filling Hard core, broken to gauge 40 mm to 63 mm at electrical substations, as directed by Engineer-in -charge.

Supply & fix embeded electronic water level controller to control pump operations to supply the water to over head tank from UG sump at Central AC plant Emission lab, including submersible pump -01 No of suitable capacity, automatic sensors, cables, pipes and mounting arrangements all as directed by Engineer-in -charge.

Supply and fix in repairs foot lamp out door type 3 w for staircase/Steps all as directed by Engineer-in -charge.

OM SAI ASSOCIATES (BID ID -3051630)

Smruti Construction (BID ID -3051584)