30(W)/EDCS/2023-24

Amount

STP 11Mtr. long

PCC pole 8.5Mtr. Long

Top channel (125X65X2240MM)

MS T-Off channel (125X65X1300MM)

11 KV Disc insulators T & C type

11 KV disc fitting T & C type

11 KV Pin insulator polymer type

11 KV cross arm V type

11 KV F clamp

Stay set complete

MS Earthing rod

GI wire 8 SWG for guarding

11 KV XLPE cable 3X185sqmm

11 KV XLPE Jointing Kit O/D type 3X185 sqmm

11 KV XLPE Jointing Kit I/D type 3X185 sqmm

LT XLPE CABLE 3.5X240 sqmm

AB cable (3X120+1X95+1X16)sqmm

Erection of the following supports including cutting, making holes, fixing of all types of accessories digging of pits complete in all respect, as per RESSPO drawing.

Single support of PCC pole 8.5 mtr long.

Single support of S.T. pole 11 mtr long.

Double pole structure on S.T. Pole 11mtr long complete with bracing.

Installation of transformer of 11/0.4 KV 25 KVA

Installation of transformer of 11/0.4 KV 100 KVA

CONSTRUCTION OF PLINTH OF TRANSFORMER (2M X2M X1.25 M) INCLUDING PROVIDING ALL REQUIRED MATERIAL COMPLETE IN ALL RESPECT.

WIREMESH FENCING OF TRANSFORMER FOR 25 KVA/63 KVA/100 KVA (AS PER NORMS) MATERIAL REQUIRED FOR CONSTRUCTION OF WIREMESH FENCING WILL BE PROVIDED AND ARRANGED BY THE CONTRACTOR.

Concreting of supports at the time of erection of pole (PCC/STP 8.50 MTR/11.00 MTR) in 1:4:8 concrete ratio from bottom of pole to ground level and plinthing of supports upto 300mm above ground level by using cement, sand & coarse aggregate in ratio 1:4:8 as per RESSPO drawing with watering/curing properly upto proper setting of plinthing. All matrial would be provided by the contractor at his own cost.

Erection of stay set with stay wire, stay clamp & stay insulator including with grouting of stay set by concrete of ratio 1:4:8 as per RESSPO norms before back fitting of the pits including binding, climbing, clamping, tightening and nozzeling of stay wire in all respect as per RESSPO norms. All clamps, nuts, bolts, stay insulator, cement. brick, ballast, sand etc would be provided by the contractor at his own cost.

Stringing and sagging of LT ABC bunch conductor of size (3X120+1X95+1X16)sqmm with proper fixing of connector (All type of clamp like suspension,I hook,dead end, connector provided by contractor at his own cost)

Earthing of each pole of the line is to be done by inserting the MS earth rod into soil by hammering and properly fastning with GI wire to each support by nut & bolt. Earthing rod must be 0.15Mtr.above from the plinth of the support. All type nut & bolt would be given by the contractor.

Pipe earthing for Transformer Plinth (All material and equipments shall be provided by the contractor.)

Guarding of HT/LT/Telephone Line/ Road/River Crossing etc. by providing G.S Earth wire 7/16 SWG/GI wire No. 8/10 and making net with difference of 1.00 Mtr. Completely including fixing of channel/angle etc. with proper locking at each support as per RESSPO norms. All type nut &bolts, would be given by the contractor at his own cost.

Laying and dressing of 11 KV XLPE 3X185sqmm XLPE cable from D/P or Single pole by excavation of trench in the ground of size 450mm wide, 1000 mm deep providing 150 mm fine sand cushion below the cable. The cable shall be duly protected by bricks, sand and stone slab and refilling and rampinf of the left out soil. Spare cable shall be left and buried in the trench in the shape of ring at both ends. (All decentralised material to be provided by contractor at his own cost)

Laying and dressing of LT XLPE 3.5×240 SQMM cable from D/P or Single pole by excavation of trench in the ground of size 450mm wide, 1000 mm deep providing 150 mm fine sand cushion below the cable. The cable shall be duly protected by bricks, sand and stone slab and refilling and rampinf of the left out soil. Spare cable shall be left and buried in the trench in the shape of ring at both ends. (All decentralised material to be provided by contractor at his own cost)

11 KV XLPE Cable 3X185 SQMM laying by drill method in HDPE Pipe (6" DIA, PE100/PM 160) single circuit (HDPE pipe provided by contractor at his own cost)

LT XLPE 3.5×240 SQMM laying by drill method in HDPE Pipe (6" DIA, PE100/PM 160) single circuit (HDPE pipe provided by contractor at his own cost)

Hoisting of 11 KV 3X185 Sq. mm. XLPE cable on double pole in HDPE Pipe (6" DIA, PE100/PM 160) including its jumpering complete along with cost of HDPE Pipe (6" DIA, PE100/PM 160) 3 M long, clamps, nuts and bolts.

Fixing of 11 KV 3x185sqmm O/D

Fixing of 11 KV Cable Marker on the route as per indian standards. The markers shall be as per indian standards with impressed character; (all material would be provided be contractor)

Fixing of danger board and G.I barbed wire on each pole including proper clamping. (All material would be provided by contractor).

Painting of ST POLES of the 33KV/ 11 KV line with one coat of red oxide primer and two coats of aluminium white paint of ISI mark and top danger portion of each support must be painted by providing two coat of Post Office Red Paint (1.5mtr upper portion of support.) Paint and material would be given by contractor to complete of work at his own cost.

Clearing of the line route by cutting of tree branches during erection of line and also upto the time of energisation completely as per direction of site incharge.

Back cartage & dismentaling of old material from different sites to store center, Baibagh, Shahjanpur including loading and unloading. Complete job as per requirement and instruction of JE/SDO concerned.

DURGESH CHANDEL

M/s Shubham Traders