Special repair to Raw Water Pump House under GE Faridkot Mil Stn

Amount

M&L for taking down cement plaster on brick or stone walls/ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed .

M&L for rendering 15 mm thick in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed .

M&L for rendering 10 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of wall and applying three coats of white wash complete all as specified and directed .

M&L for preparation of newly plastered or unplastered ceiling surfaces and applying two coats of white wash complete all as specified and directed .

M&L for preparation of newly plastered or unplastered surfaces of wall and applying two coat of cement base paint complete all as specified and directed

M&L for complete removal of existing treatment of old decorated surfaces of wall by brooming down and scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat white wash complete all as specified and directed.

M&L for complete removal of existing treatment of old decorated surfaces of wall by brooming down and scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat colour wash complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed .

S&F Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying finishes complete all as specified and directed .

S&F Glazed ceramic coloured tiles 450mmx300mmx7mm thick (colour and shade as approved) as in vertical surfaces such as skirting/dados etc, set and jointed in neat cement slurry & pointed in white cement with pigment to match the colour of tiles over & including 15mm thick rendering in cement mortar 1:4 complete all as specified and directed

S&F Green Marble 20mm thick work (table rubbed and polished) as in cooking platforms and like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including nosing edges over and including 20 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.complete all as specified

S&F Machine cut kota stone slab in flooring 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing,cutting and mirror polishing over and including 20 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

S&F Machine cut kota stone slab 20-25 mm thick as in skirting, set and jointed in cement slurry over & including 15 mm thick rendering in cement mortar1:4 and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type polishing complete all as specified and directed .

Demolition of brickwork or stone/boulder masonry,built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed

M&L for brick work with fly ash bricks using old size bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed .

All as per Srl item No. 17 here-in-before but except bricks.

Demolition of concrete (un-reinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and directed

M&L for 75 mm thick cement concrete 1:3:6 type C2( using 40mm graded crushed aggregates) as in plinth protection finishing surfaces even and fair complete all as specified and directed .

M&L for 100mm thick plain cement concrete 1:2:4, type B-2 (using 40 mm graded crushed stone aggregates) as in sub base,mass filling complete all as specified and directed

Dismantling posts or struts (wood, steel or RCC) of any section, including taking out embedded portion in concrete, brick work etc and making good the disturbed ground complete all as specified and directed .

M & L for cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in foundations, filling and mass concrete complete all as specified and directed .

S&F angle iron posts and struts in fencing, including cutting tops to shape as directed, drilling holes, notching for wire etc,including all necessary drilling, bolting or riveting etc and similar works conforming to Fe-290 Gde E-165 quality complete all as specified and directed .

Dismantling fencing wire mesh, any type complete all as specified and directed .

Supply only mild steel galvanized chain link fencing of any size or type complete all as specified and directed. Note: The weight of chain link fencing shall be ascertained by BOO as ordered by GE and payment shall be made accordingly and contractor shall have no claim on this account.

Fixing only chain link fencing including line wires(steel wire), any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire compete all as specified and directed .

Supply only mild steel in flat, round or square bars, in available length in FE 410-W (Gde E-250) quality -A complete all as specified and directed

Supply & Fix mild steel screw bolts machine made with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut shank size 5mm to 10mm dia and n. exc. 5cm long complete all as specified and directed

S&F in repair galvanised,2strand,steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossings with and provision of galvanised mild steel wire,staples or steel pins etc. complete all as specified and directed .

Dismantling asbestos cement (corrugated, semi-corrugated .) sheets in roof coverings complete all as specified and directed.

S&F 6 mm thick asbestos cement (corrugated / semi corrugated) sheets as in roof/wall covering and fixed with L-type or J-type or cranked hook bolts etc complete all as specified & directed

M&L for asbestos cement sheet two piece plain angular ridge 6 mm thick fixed with L-type or J-type or cranked hook bolts etc complete all as specified & directed

Dismantling unframed timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section and in any position complete all as specified and directed

S&F Rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails fixed with angle cleats or other connecting plates conforming to Fe-410-W(Gde-E-250, quality-A) complete all as specified and directed

Framed work such as grills, gratings etc. with ends of bars shoulderd and/or riveted, or forged into spikes, framed guard bars, barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe290, Gde-E-165 complete all as specified and directed.

S&F in repair bib tap chromium plated with crutch or butter fly handle, screwed down, screwed for 15mm bore pipe & fixed complete all as specified and directed .

S&F in repair pillar taps,fancy type,chromium plated ,cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of 15mm bore complete all as specified and directed

S&F vitreous china wash hand basin, white, flat back of size 550mm x 400mm including CI brackets, CP brass waste coupling with rubber washer and waste pipe 32mm bore complete all as specified and directed .

S&F in repair 10 litres PVC,valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair Vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white, with integral foot rests, CI 'P' or 'S' traps 100mm & PVC flush pipes 32mm dia including connecting to trap and to flushing pipe, anti-syphonage pipe etc including all joints and making good to floor complete all as specified and directed.

S&F Shelf of PTMT, fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed

S&F in repair Stop valve/angle ball, cast copper alloy,fancy type,chromium plated, screwed down for high pressure with crutch or butter fly handle, screwed both ends for iron pipe of 15mm bore complete all as specified and directed .

S&F PVC connection, 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F brass chromium plated shower rose 125mm size with shower arm 15mm size, 195mm long with bend of 45 degree with flange all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 Ltr capacity,triple layered, hoisted and fixed in position including ball brass valves, high pressure, with polythene float and fly nut screwed for 20mm bore iron pipe complete all as specified and directed .

S&F in repair brass chromium plated tubular towel rail 20mm dia, D type, 600mm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed.

Taking up or down 15mm dia GI/PVC tubing and connection including, cleaning for refixing or removal to store complete all as specified and directed .

Taking up or down 20mm dia GI/PVC tubing and connection including, cleaning for refixing or removal to store complete all as specified and directed

S&F GI tubing,15mm bore, medium grade with all fittings , fixed to wall/ceiling and laid in floors complete all as specified and directed .

All as per item No 51 here-in-before but except tubes

S&F GI tubing,20mm bore, medium grade with all fittings , fixed to wall/ceiling and laid in floors complete all as specified and directed .

All as per item No 53 here-in-before but except tubes

S&F in repair 20mm bore stop valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for GI out let/inlet pipe or for union including threading to existing pipes on both ends complete all as specified and directed.

S&F in repair 15mm bore stop valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for GI out let/inlet pipe or for union including threading to existing pipes on both ends complete all as specified and directed.

Dismantling CI/PVC pipe of 75/100mm dia alongwith fittings ,below or above GL/laid in floors/fixed to walls jointed in cement mortar complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches/in floors/fixed to walls including fixing clamps with nut and bolts complete all as specified and directed .

S&F PVC (SWR) bends any radius ,110mm bore complete all as specified and directed.

S&F in repair round / square grating of PTMT of size 100mm (minimum weight 50gms). Jointed to PVC pipe complete all as specified & directed .

Taking down chowkats or frames n.exc 1.5 Sqm each with shutters (without taking of shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sqm but n. exc 4 sqm each with shutters (without taking of shutters from the frames) complete all as specified and directed

S&F Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.complete all as specified and directed

S&F Pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.complete all as specified and directed.

M&L for PCC 1:3:6, type C0 (using 12.5mm graded crushed stone aggregates) as in back filling of pressed steel frames, bed blocks, fixing of hold fasts etc including necessary formwork complete all as specified and directed

S&F 30 mm thick 2nd class hard wood, plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edges) or of vaneered partical board medium desnsity, wood partical board with commercial face veneers fitted to chowkats complete all as specified and directed

S&F 30 mm thick 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats complete all as specified and directed

S&F Solid wood moulded grain printed PVC door frame of size 50mm x 95 mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. square tube, egdes will be painted to match printed sheets complete all as specified and directed .

S&F Factory Made Solid PVC Moulded Door Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Woodgrain moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified and directed

S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed

S&F 100mm mild steel butt hinges, medium weight,cold rolled complete all as specified and directed.

S&F aluminium anodised barrel tower bolts, 150 mm long of extruded section, fixed to doors with screws complete all as specified and directed .

S&F Aluminium anodised, cast type, handle 150 mm size complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminium alloy and fixed complete all as specified and directed .

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed .

S&F in repair 3mm thick, figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed .

M&Lfor preparation of new or previously untreated wood or wooden based surfces of any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed .

S&F in repair cast iron or mild steel peg set, 175mm to 250mm with hook fixed with wall complete all as specified and directed .

M & L for Pre cast cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in manhole cover slab, rounded or chamfered on edge included neccessary formwork, set in cement mortar 1:4 complete all as specified and directed .

M&L for Mild steel TMT bars 6 to 8mm dia , cut to length, bent to shape as required, including cranking, bending and binding with & including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed .

Demolition of concrete (un-reinforced) in roofs including finishes thereon, any thickness(whether full thickness removed or only part thereof ) complete all as specified and directed .

Dismantling of brick tiles or terracing tiles single layer on roof & disposal of retrieved material to a distance n.exc 100m from the starting point complete all as specified and specified

M&L for rendering 10 mm thick in cement mortar 1:3 with WPC on fair faces of brick work or concrete surfaces as in roof complete all as specified and directed . Note : WPC will be measured and paid separately

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and directed .

M&L for polythene film, 300 micron thick, laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm conforming to IS specification with lap joints 100mm wide complete all as specified and directed

M&L for lime concrete 1:2:5 (Lime:surkhi:brick ballast(40mm)) terracing in roof complete all as specified and directed .

M&L for 40mm thick brick tiles laid on lime concrete and joints grouted flush in cement mortar 1:3 mixed with 5% of crude oil by weight of cement on mud phuska complete all as specified and directed .

All as per item No 89 here-in-before above but except brick tiles

Supply only Liquid water proofing compound

M&L Spreading and leveling of existing earth embankment,ramming/rolling and finishing to required size in layers n.exc 25 mm thick complete all as specified and directed.

S&F in repair Steel rolling shutters having thickness of laths1.25mm, gear operated type with bevel gear box and crank handle, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed.

S&F ball bearing for rolling shutters complete all as specified and directed

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed

Excavation in trenches in any type of soil not exceeding 1.5m deep and 1.5m wide, for foundation,mass filling etc or manholes,piers,shafts etc not exceeding 10 Sqm on plan and getting out complete all as specified and directed.

All as per Srl item No. 96 here-in-before but depth exc 1.5m but not exc 3.0m for poles

M & L for old size bricks with fly ash in one brick thick honey comb wall built in cement mortar 1: 4 complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed

Removing excavated material to a distance n exc. 50m and depositing where directed at a level n exc.1.5 m above the starting point complete all as specified and directed

M&L for hard core of gauge not exceeding 63mm using broken stone or boulders, deposited, spread and leveled in layers not exc 15cm thick, watered and rolled/rammed to a true surfaces complete all as specified and directed .

M&L Sand filling under floors etc in layers n.exc 25 mm thick complete all as specified and directed.

M&L machine pressed, precast concrete interlocking coloured paver block, any shape and size confirming to IS-15658-2006 of 80mm thickness, M-40 Grade with grey cement and pigment complete all as specified and directed .

S&F factory made precast kerb stones in PCC 1:2 :4 type B-1 including chamfers, weatherings,throatings etc in smooth finish & set in cement mortar 1:4 including necessary excavtion and earth work for embedding kerb stone at a depth as directed and temping around kerb stone and removal of surplus soil to a distance not exceeding 50 m and depositing where directed complete all as specified and directed .

M&L for preparation of new plastered /concrete surface and painting with two coats of synthetic enamel paint (white/golden yellow) over a coat of primer complete all as specified and directed

Taking down MCCB, MCB, DB TPN/SPN and making good the disturbed walls and surface area etc complete all as specified and directed .

Taking down carefully existing aluminium/copper point wiring for light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells & making good the disturbed surfaces of walls, matching the colour with existing surface complete all as specified and directed. Note : Rate for making good shall be deemed to be included in above item rate.

Taking down unserviceable submain wiring, any size, any run with earthing cable and making good the disturbed area complete all as specified and directed.

Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLS with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed conduit of suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes, 2mm thick galvanised steel pressed sunken terminal boxes of suitable sizes for mounting of switches, sockets, fan regulator etc, covered with 2.8mm thick plastic laminate Hylem / Anchor top cover sheet of required colour, fixed with brass screws and cup washers, painting terminal boxes inside and outside with one coat of red oxide primer including continuous earth wire of size 1.5 Sqmm PVC stranded copper conductor unsheathed, insulated, stranded (Green colour) connected to common earth point dolly for One light point/ fan point/ exhaust fan point to be controlled by one number one way switch complete all as specified and directed .

All as per Srl item No. 109 here-in-before but for one three pin socket outlet 5 Amp on the same board with other switches complete all as specified and directed

All as per Srl item No. 109 here-in-before but for one switch socket combination, 3 Pin 5 Amps, 230 Volts on independent board complete all as specified and directed

All as per Srl item No. 109 here-in-before for switch socket combination (multi purpose) 6 Pin 15 Amps 230 volts point to be controlled by one switch and wiring with 2.5 Sqmm FRLS PVC unsheathed copper conductor and FRLS cable 2.5 Sqmm PVC insulated earth wire on independent board.complete all as specified and directed .

S&F PVC Lamp holder with back plate suitable for batten fittings complete all as specified and directed .

S&F LED bulb 1x10 watt having luminous efficiency warranty 2 years complete all as specified and directed .

S&F complete set of tube light fitting, 1x20 watt LED (4 feet long) 230 volt, decorative ultra slim linear LED lighting fixture with environment friendly, energy efficient ready to use pack etc with all acessories such as LED adopter, LED tube, internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed

S&F complete set of tube light fitting, 1x10 watt LED (2 feet long) 230 volt, decorative ultra slim linear LED lighting fixture with environment friendly, energy efficient ready to use pack etc with all acessories such as LED adopter, LED tube, internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed

S&F ceiling rose, three terminals, PVC polycarbonate, isolated body with bakalite 20mm back plate complete all as specified and directed.

S&F Sub main wiring with two runs of single core PVC FRLS sheathed, insulated, copper cable of 6 Sqmm size, multi stranded, 1100 volts grade with PVC insulated FRLS copper wire 6Sqmm for continous earth wire drawn into and including concealed conduit of suitable size complete all as specified and directed . Note :- Two runs of 6 Sqmm copper cable and one run of 6 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length)

S&F switch piano, flush type, single pole, one way, 5/6 Amps, 230 volts, AC supply complete all as specified & directed

S&F socket outlet, two-in-one, 5 pin, 5 Amp, 230 volts, AC supply complete all as specified & directed

S&F switch piano, flush type, single pole, one way, 15/16 Amps, 230 volts AC supply complete all as specified and directed

S&F socket outlet ,2 in 1, 5/6 pin, 15/16 Amps, 230 volts ,AC supply complete all as specified & directed

S&F Sheet metal enclosure for DBs,TPN, double door, 415 Volts,4 ways, vertical type and space for MCCB complete all as specified and directed .

S&F Sheet metal enclosure for DBs,SPN, double door, 230 Volts, 4 ways with 200 amps rated bus bar complete all as specified and directed .

S&F Sheet metal enclosure for DBs,SPN, double door, 230 Volts,8 ways with 200 amps rated bus bar complete all as specified and directed .

S&F MCCB 3 Pole,415 V, adjustable type, 100 Amps with breaking capacity 16 KA complete all as specified and directed .

S&F MCB, SPN, 32 amps, 230V, C Series with breaking capacity 10 KA complete all as specified and directed

S&F MCB SP 5 to 32 Amp, 230 volts, B Curve with breaking capacity 10 KA complete all as specified and directed

M&L for Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, buried directly in ground vertically (depth of pit not less than 2.25m below normal ground level), with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to electrical equipment/GOD/LA and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI medium grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of precast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Schedule Part-I (2009), complete all as specified and directed. Note(s):- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 1000 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m, excess beyond 7.5m length required at site shall be measured and paid separately. (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) Quoted lump sum / rate shall be inclusive of above all provisions.

Supply, fixing and testing LED street / security light fitting of 25 Watt fitted on 4 to 9 meter high octagonal pole / wall/Swan neck pole including LED lamps complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminium alloy. The luminaries shall be monolithic construction, totally enclosed, dust and water proof with minimum IP-65 protection as per IS-10322-1982 (Part-I) with latest amendments and input voltage range 140-300V, AC, frequency 50-60 Hz, PF should be more than 0.9 with total harmonic distoration. THD (I) less than 15%, cool white colour and lamp starting time should not be more than 10 second, Fittings should be provided with 10 KV surge protection. Driver should be constant current constant voltage driver. Driver should have high voltage withstanding capacity upto 300V, AC. Driver should also have double phase protection, no load, open circuit and short circuit protection. LED light fittings should be suitable for ambient temperature from - 10 degree centrigrade to 50 degree centigrade and humidity level 10% to 90% RH. Covers should be polycarbonate/ toughened glass to ensure minimum IP 65 degree protection. Cover should not degrade due to heating and ageing. The efficient of LED luminaries system shall be more than 85 lumens per watt and must be certified by LM-79 test report fixed on and including bracket of 40mm dia,light grade ,GI pipe ,1.20 m and connecting with twin core twisted flexible copper conductor cable 1.5 Sqmm including taking down existing one complete all as specified and directed. Note :- (a) Bidder shall submit test report of LED street light fitting from accredited test laboratory for LM-79 (b)Bidder has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of CA. The product will be replaced free of cost in the following cases : - (i) Manufacturing defects (ii) Failure due to mechanical and electrical impact, (iii) Drop in lumen (or lux at 1m) below 90% of claimed values of lumen (or lux at 1m) of the LED/ luminairies. (c) All LED light luminaire must meet the provision laid down in IS-16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part-II/ Section 13 (d) Scope of work shall include supply and fixing street light fittings on poles which includes required T & P and accessories etc if any, making connection, testing etc complete. No extra payment is admissible on these account.

S&F GI tubing,25mm bore, medium grade with all fittings , fixed to wall/ceiling and laid in floors complete all as specified and directed

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed for 25 mm dia of pipe complete all as specified and directed.

S&F in repair 1X10 watt LED retrofit type bulk head fitting luminaries, die cast, aluminium alloy body, heat resistant, prismatic glass cover with specially designed gasket, lamp holder etc complete with all accessories and including connecting up with twin core twisted flexible copper coductor cable with suitable size of 230 volt,50 HZ complete all as specified and directed.

Taking down and Refixing only ceiling fans, any sweep, connecting up with and including three core copper flexible wire not less than 0.5 mtr for connecting from ceiling rose / connector to ceiling fan complete all as specified and directed

Supply, installation, commissioning and testing water storage heater (geyser) vertical type of 25 ltr capacity, ultathick stainless steel superior 304 Gde PUF insulation thermostate, thermal cut off, 1PX4 multifunctional safety valve technology, feroglas dry powder coating finish, suitable for to operate / function on AC 220 V, single phase having heating element of 2 KW capacity and high thermal cut-out, energy saving BEE 5 star rating including fixed along walls including grouting fastening & fixing (04 Nos) 16mm dia 150mm long GI bolts & nuts, washers and connecting up inlet/ outlet with cold and hot water PVC connection pipes and electric connections cable cord min 1.50m length with copper conductor cable 3 core and 3 pin plug 15/16 Amp, including making good the disturbed surfaces matching with existing complete all as specified and directed

S&F stepped type electronic fan regulator, flush type on the existing pheonolic laminated sheet etc, single phase, AC supply, 230 V and connecting up complete all as specified and directed .

Taking down and Refixing only exhaust fan, complete with accessories, any size, connecting up with and including two core copper flexible wire not less than 0.5 mtr for connecting from incoming to outsoing any size complete all as specified and directed

S & F exhaust fan ,steel body, AC single phase, 4 blades with louver shutter suitable for operation on 220/230 volts of 300mm sweep and all fixing arrangements like wall hole, material etc complete all as specified & directed

S&F in replacement fully automatic, air break, star delta electric motor starter, 3 phase, 415 volt suitable for 20 HP motor, Amp range 28-36 complete all as specified and directed.

S&F in replacement of sluice valve of size 300mm,class PN-1.6 ( ISI marked) with brass spindle, flanged end including jointing with Neoprene rubber gasket, nuts, bolts and washers etc as per existing complete all as specified & directed .

S&F in replacement of sluice valve of size 500mm,class PN-1.6 ( ISI marked) with brass spindle, flanged end including jointing with Neoprene rubber gasket, nuts, bolts and washers etc as per existing complete all as specified & directed .

S & F in replacement Cast Iron Non return valve conforming to ISI-5312 suitable for 300 mm bore pipe, heavy duty ,both end flanged with by pass charged of pressure rating PN 1.6 and jointing with rubber or fibre board gasket complete with and including required nos size of nuts, bolts and washers complete all as specified.

M&L for plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) in kerbs/coping/bed plates and the likes including weathering, slightly rounded or champhered angles with necessary formwork for pipe support , finishing even and smooth without using extra cement complete all as specified and directed

S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed .

S&F in repair 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed .

M&L for CI fitting for spigot & socketed pipes of bore upto 500 mm i.e bends, tapers, tee pieces ,caps & plugs etc complete all as specified and directed .

Dismantling existing lead joint of 80 mm bore pipe and providing new run lead joint using old retrieved lead & additional lead, if reqd at site complete all as specified and directed .

Dismantling existing lead joint of 300 / 500 mm bore pipe and providing new run lead joint using old retrieved lead & additional lead, if reqd at site complete all as specified and directed .

S & F in replacement 50 mm bore, cast iron, air release valve, flanged type with two air out lets including jointing with nuts, bolts, washers and rubber sheet etc complete all as specified and directed .

Taking up or down cast iron water mains including all fitting with spigot or socket ends and lead joints including burning out joints and recovering lead for 80/100 mm bore pipes complete all as specified and directed.

Taking up or down cast iron water mains including all fitting with spigot or socket ends and lead joints including burning out joints and recovering lead for 500 mm bore pipes complete all as specified and directed.

Supply and laying cast iron pipes of 80mm bore with spigot and socket ends, centrifugally cast, class LA ,laid in trenches all as specified and directed.

Supply, laying, jointing, commissioning and testing ductile iron pipes of 500mm bore with spigot and socket ends ,centrifugally cast (spun), class K-9, conforming to IS-8329-2000, in any length with & including rubber push (tyton) joint, laid in trenches complete all as specified and directed .

S & F D Clamps of size 500mm of ductile iron pipe suited for 300mm dia pipe complete all as specified and directed .

Dismantling existing mild steel sheet cover of any thickness from existing valve pit and providing new cover of 3.15mm thick mild steel sheet with locking arrangement, butt hinges, handles and other connected items duly fixed to existing angle iron frame complete all as specified and directed

M&L for prepration of old metallic , treated irregular and curved surfaces of pipes , valves, motor, pumps , electric panels , steel railing , agitators of flocculators including removing existing treatment by scrapping, burning and painting with two coats of synthetic enamel paint complete all as specified and directed

M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment.

M&L for brick protection with old size sub class 'B' bricks, laid flat , length of bricks across the route of underground cable complete all as specified and directed .

Boring/Drilling ( horizontally) manually under existing road ( maximum 10 M in width) suitable for passing GI tubing of 40 to 80 mm bore complete all as specified and directed

S&F in repair GI pipe, light grade, 40mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavement complete all as specified and directed. Note : (i) Excavation and earth work shall be measured and paid separately.

S&F in repair GI pipe, light grade, 80mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavement complete all as specified and directed. Note : (i) Excavation and earth work shall be measured and paid separately.

S&F in repair MCCB 400 Amps, 4 Pole, 36 KA, 415 volt 50 Hz, with fixed type thermal magnetic release complete all as specified and directed

S&F in repair MCCB 63 Amps, 4 Pole, 25 KA, 415 volt 50 Hz, with fixed type thermal magnetic release complete all as specified and directed

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 16 Sqmm, 4 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete including taking out old cable & bricks all as specified and as directed. Note: (i) Returning filling, earth work, sand cushioning and brick cover for protection of cable shall be measured and paid separately.

All as per Ser item No 164 here-in-before but of Size 120 Sqmm 3.5 Core

All as per Ser item No 164 here-in-before but of Size 95 Sqmm 3.5 Core

S&F in replacement pre-stressed cement concrete pole, 9 metre long of cross section 102mm x 172mm at top and 102mm x 279mm at bottom, class 10, complying with requirements of IS-1678-1998, errecting truly in vertical position including painting of poles with two coats of synthetic enamel paint over a coat of primer in alternate strip of 30cm each in black and white colour upto 1.5 metre height from top of PCC pedestal/coping of poles and numbering of poles with synthetic enamel paint black in 80mm high letters over 150mm x 230mm yellow base made from synthetic enamel paint complete all as specified and directed

M&L in repalacement for Stay assembly comprising of 7/8 SWG galvanised stay strand complete with GI stay rod 16mm dia ,mild steel stay plate, stay bow,connecting bracket of suitable mild steel flat , nuts, bolts, washers,loop type insulators etc complete all as specified in electrical plate No I of SSR-2009 (Part- I) complete all as specified and directed.. Note:- Excavation and earth work , PCC shall be measured and paid separately under relevant items of BoQ’.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in coping of poles etc including weathering, slightly rounded or chamfered angle and throating, necessary form work and fair finishing all exposed faces of concrete without using extra cement complete all as specified and directed

M&L post top LED 40 watt made in cast aluminium spigot housing with decorative clear opel acrylic diffuser with IP 65 protection with complete proper connection with service wire and fixing arrangement for gate pillar complete all as specified and directed Make : Bajaj Cat Part No. BGCT W40 LED WW or equivelant in Havells/ Philips, Halonix

Supplying, jointing and testing in replacement of heat shrinkable type end termination cable jointing kit, outdoor type, suitable for 11KV under ground earthed system 3 core XLPE cable of size 95 Sqmm including making connections and taking out old u/s joint complete all as specified and directed.

Supplying, jointing and testing in replacement of heat shrinkable type end termination cable jointing kit, outdoor type, suitable for 11KV under ground earthed system 3.5 core XLPE cable of size 120 Sqmm including making connections and taking out old u/s joint complete all as specified and directed.

Supply, fixing and testing LED flood light fitting of 160Watt fitted on 4 to 9 meter high octagonal pole / wall /Swan neck pole including LED lamps complete with body robust, corrosion, resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminium alloy. The luminaries shall be monolithic construction totally enclosed dust and water proof with minimum IP-66 protection as per IS-10322-1982 (Part-I) with latest amendments and input voltage range 140-300V, AC, frequency 50-60 Hz, PF should be more than 0.9 with total harmonic distoration THD (I) less than 15%, cool white colour and lamp starting time should not be more than 10 second, Fittings should be provided with 10 KV surge protection. Driver should be constant current constant voltage driver. Driver should have high voltage withstanding capacity upto 300V, AC. Driver should also have double phase protection, no load, open circuit and short circuit protection. LED flood light fittings should be suitable for ambient temperature from - 10 degree centrigrade to 50 degree centigrade and humidity level 10% to 90% RH. Covers should be polycarbonate/ toughened glass to ensure minimum IP 65 degree protection. Cover should not degrade due to heating and ageing. The efficieny of LED luminaries system shall be more than 85 lumens per watt and must be certified by LM-79 test report complete all as specified and directed . Make: Crompton/ Bajaj/Havells/Halonix/Philips Note: (a) Bidder shall submit test report of LED street light fitting from Govt approved accredited test laboratory for LM-79. (b) Bidder has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of CA. The product will be replaced free of cost in the following cases : - (i) Manufacturing defects, (ii) Failure due to mechanical and electrical impact, (iii) Drop in lumen (or lux at 1m) below 90% of claimed values of lumen (or lux at 1m) of the LED/ luminairies. (c) All LED light luminaire must meet the provision laid down in IS-16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part-II/ Section 13 (d) scope of work shall include needful T & P and required accessories etc as per manufacturers recommendation complete including making connection, testing etc complete. Note: Every light fitting will be warranty 5 years after completion of CA and replacement/defects as applicable should be complied/rectified within 7 days .

Supply & fixing in replacement thermoplastic cable junction boxes ,IP65 with metric knockout for cable entry of size 250x200x100 mm, fixed on pole/wall with MS clamps/MS flat iron (as per site requirement) of size 25x4 mm, nuts, bolts,washers and glands, including 4 nos aluminium bus bar strip of size 15cmx3mm and one No MCB SP 6 Amp complete all as specified and directed.

S&F PVC insulated, multistranded aluminium conductor, PVC sheathed cable, 4 sqmm 2 core and making connection of street light fittings with overhead lines/ UG cable complete all as specified and directed .

Surface dressing not exc 15cm deep in soft/ loose soil including cleaning of E/M installations premises, uprooting of tiny trees, tree cutting, cleaning, levelling, spreading bushes, beeds, grass, removing poly bags, brick bats, stone pebbles debries, cleaning of sub station bldg, two pole/ four pole structure area, HT line etc and removing to a distance not exc 50 Mtr complete all as specified and directed

M&L for filling and spreading aggregate using 40mm grade trap stopne aggregate around 4 pole, 2 pole structure and transformer etc complete all as specified and directed

S&F GI earth wire 4 mm dia for earth coninuing on LT overhead line complete all as specified and directed

Supply and fixing in replacement of air break gang operated switch, triple pole, 11 KV (outdoor type) mechanically operated, suitable for horizontal or vertical mounting fixed type complete with 12 insulators and steel frame, with operating mechanism worked from ground level with fixed contacts of phosphorous bronze and moving control of copper, for current rating upto 200 Amps including GI pipe heavy duty of required size and with locking arrangement including Godrej (Freedom) 65mm pad lock with two keys with fuse mounts, fuse carriers and HT fuse elements having 400 amp rating suitable for HT 11 KV, 50 Hz, AC supply including necessary electric connections complete and painting with 2 coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed

Supply and fixing in replacement lightning arresters Polymeric insulator for non linear resistance type for 11 KV normal discharge count 5 Amps and high current impulse withstand 65 Kilo Amps conforming to IS-3070 Part-I for OH line including bracket, clamps, nuts and washers complete all as specified and directed by Engineer -in-Charge.

S&F Cross arms, bracing, supports, clamps and back plates, fabricated from structural steel section Fe-290 grade E-165 quality including nuts, bolts, washers, and welding, bending cold or hot, drilling holes for bolts, in any shape or size as directed including two coats of alminium paint over a coat of red oxide primer complete all as specified and directed.

Collecting & transporting carefully the unserviceable transformers oil cooled copper wound of capacity 100 KVA (indoor type) from Raw water, for rewinding ,cleaning & desclaling ,scraping out of old paint & spray painting with superior quality smoke grey synthetic enamel paint to all exposed surfaces , assembling the transformers, testing and writing MES & SM Numbers with white paint over black base in letters of height not less than 10 cm, transporting back to site from repair workshop and installing, hoisting of transformers on two/four pole structure at height not less than 3 metre, making all electric connections with HT/LT side jumbers and leads including earth connections etc. and testing complete all as specified and directed by Engineer-in-charge Note : i) Transformers shall be got repaired from factory/work shop as directed by Engr-in-Charge ii) The transformer shall be dismantled in presence of contractor and MES Representative/AGE E/M iii) The defective parts to be replaced shall be measured & paid for separately (iv) Safe oil container for collecting old transformer oil will be arranged by the contractor. (v) The T&P such as chain pulley, crane for loading unloading, transporting and for installing and hoisting shall also be arranged by the contractor at his own arrangement.

Supply and fixing in replacement defective HT/LT coil DPC copper windings strip of existing size(gauge), or cross section of winding wire as per recomendation and design of OEM grade and in weight as per existing oil coil complete with insulating material for transformer 100 KVA Cap, complete all as specified and directed.

Supply and fixing in repair HT porcelain bushing including heat resistance gasket, brass spindles, nuts, bolts, washers for transformers of capacity 100 KVA complete all as specified and directed

Supply and fixing in repair LT porcelain bushing including heat resistance gasket, brass spindles, nuts, bolts, washers for transformers of capacity 100 KVA complete all as specified and directed

Material and labour for replacement of silica gel of air breather filled complete for transformer of capacity 100 KVA complete all as specified and directed

S & F for Top up with fresh transformer oil in transformer at site having requisite dielectric strength as per latest IS specifications complete all as specified and directed

Dehydration/filtration of transformers oil of existing transformerat site by means of oil dehydration machine having arrangement for heating to remove the moisture silt/sludge and wastage removing arrangement etc to make the oil fit for use in accordance with IS-1886 to achieve minimum dielectric strength of 42 KV by continoues process of dehydration complete including testing at standard gap of 2mm by oil testing machine complete all as specified and directed . Note :- (i)Electricity for running dehydration machine & testing shall be provided by the deptt free of cost. (ii) Testing machine to be arranged by the contractor under his own arrangement.

M&L for Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, buried directly in ground vertically (depth of pit not less than 2.25m below normal ground level), with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including GI strip 32x6mm by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to electrical equipment/GOD/LA and protected by galvanized iron pipe light grade 40mm dia bore including watering pipe 20mm dia bore GI medium grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of precast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Schedule Part-I (2009), complete all as specified and directed. Note(s):- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with TMT bar 8mm dia both ways @100c/c. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m, excess beyond 7.5m length required at site shall be measured and paid separately. (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) Quoted lump sum / rate shall be inclusive of above all provisions.

Dismantling existing LT Panel with various size cable connections, lugs, nuts & bolts etc and shifting from existing site to another site and fixing LT panel with PCC 1:2:4 of required size as in foundation filling including necessary earth work and making cable connection etc complete all as specified and directed . Note : A sum of Rs. 2,57,528.00 will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 28 & 29 (Schedule of Credit) of Tender document

M/S BSS AND SONS

DEEPAK ENTERPRISES