SPL REPAIR TO MD ACCN BLDG NO P-160/17 TO 160/24 AT ZORAWAR MARG OF MED REGT ITARANA MIL STN ALWAR

Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars & precast concrete masonry etc complete all as specified & directed by Engr-in-Charge.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in 1:6 as in half brick thick wall complete all as specified and directed by Engr-in-Charge..

M&L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 mean radius, built in CM 1:6 complete all as specified and directed by Engr-in-Charge..

Taking down cement or cement lime plaster, any description on brick or stone walls,etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engr-in-Charge.

M&L rendering 15mm thick in cement mortar 1:4 including WPC @ of manufacture instruction by weight of cement on stone/brick masonry finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. Note : quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipments reqd to execute the work and WPC shall be incl quoted rate etc complete all as specified & directed by Engr-in-Charge.

M&L for 10mm thick cement plaster in CM 1:6 on other than fair faces of brick work or concrete surface finished even and smooth without using extra cement complete all as specified & directed by Engr-in-Charge.

M&L for rendering 5 mm thick in CM (1:3) as in ceiling and finish the surface even and smooth without using extra cement complete all as specified & directed by Engr-in-Charge.

M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand morrtar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm ) mixed with coarse sand and cement in the raio of 1:1:1 shall be applied and finished even. The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete including taking down and applied two coat of two coats of exterior emulsion paint/weather coat complete all as specified and directed by Engineer in Charge

M&L for preparation of new plastered surfaces of walls, and applying two coats of distemper oil emulsion over a coat of primer incl 2mm thick elastomeric wall care putty on walls complete and specified and as directed by engr-in -charge.

M&L for preparation of old plastered surfaces of walls including cleaning of mortar drops, smoke soot, moulds, moss, efforsecent salt, trading oil grees spots etc using grinding machine on wall surfaces and preparation of old plastered wall surfaces and applying two coats of oil emulsion distemper ( OBD) of approved shed/tint over and including a coat of white wall care putty 2 mm thick complete over a coat of primer complete all as specified & directed by Engr-in-Charge.

M&L for preparing newly plastered surfaces & applying three coat of white wash on ceiling complete all as specified & directed by Engr-in-Charge.

M&L for preparation of old surfaces of ceiling and applying two coats of white wash on ceiling complete all as specified & directed by Engr-in-Charge.

M&L preparing newly plastered surfaces of walls and applying two coats of exterior emulsion paint over a coat of 2mm thick exterior wall care putty on walls complete all as specified & directed.

M&L for preparing surfaces of old plaster on walls and applying two or more coats of APEX/WEATHER coat over 3mm putty including priming coat of exterior primer applied up to forth stories building height complete all as specified & directed.

Dismantling floor hearth wall tiling (but not backing) removing servicable tiles to store rubbish off the premisses complete all as specified & directed by Engr-in-Charge.

M&L for Glazed coloured ceramic tiles in vertical surface of size as approved by Engr-in-Charge and 7-8mm thick laid over and including 10 mm rendering in CM 1:3 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified & directed by Engr-in-Charge.

M&L for non skid ceramic tiles (coloured) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. laid over and including 10 mm rendering or bedding layer in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified & directed by Engr-in-Charge.

M&L Vitrified tiles 8-10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified & directed by Engr-in-Charge.

All as per ser item No 18 above but as in skirting/dado including cement mortar 1:4 10mm thick complete all as specified & directed by Engr-in-Charge.

M & L 25 mm thick PCC 1:2:4 type B0 (12.5mm graded aggregate) as in sub base for floor including demolition complete all as specified & directed by Engr-in-Charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc,laid , bedded and pointed in any mortar all complete all as specified & directed by Engr-in-Charge.

M&L for 18-20 mm thick polished green marble work as in riser, thread, jambs, pillars, window- cills,cooking platforms, flooring laid in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of green marble laid over 15 mm screed/ rendering layer in CM 1:3, including grinding of edges to curved surface finish, LPG gas pipe line hole etc complete all as specified & directed by Engr-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n exc 1.5 Sqm each incl making good the dismantling portion of wall etc complete all as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 but n exc 4 sqm each incl making good the dismantling portion of wall etc complete all as specified & directed.

Taking down of shutter exc 1 sq. m and n exc 2 sq. m each complete all as specified & directed.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisturproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with Four numbers stainless steel butt hinges on each shuttrs of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardanand fixed in position with MS hold fast/ugs/SS dash fasteners of required dia including necessary hold fast/lugs or SS dash fastner/necessary cutting hole in wall and making good the wall with filled the holes alongwith PCC 1:2:4 or CM 1:4 etc complete all as per direction of Engineer-in-Charge.

S&F Aluminium window/ Ventilator with fly proof shutter and glaze shutter both made of 1.59mm thick powder coated (Thickness of powder coating not less than 50 micron) frame incl all necessary jointing cleats, glazing clips, rubber neoprene packing for fixing of 4mm thick glass and galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm with frame incl aluminiun 2 Nos 100mm long handle, hinges and tower bolt for each shutter etc complete as per aluminium section below and including 12 mm thick MS square guard bar grill with flat iron strip frame to be fixed with aluminium frame or wall with hole fastener incl two coat of synthetic enamel paint over red oxide primer above grill and making good the dismantled portion of wall etc complete all as specified and directed. The size of different section to be use is as under :- (a) Outer main frame to be 125X45X1.59 MM thick (b) Shutter frame 44x25x1.59 mm thick (b) Overall measurement of opening to be measure for payment purpose only and not both shutter to be measured. (Note : Glass of 4mm thick and wire mesh for mosquito proofing shall be included quoted rate.)

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel/aluminium frames with beading complete all as specified & directed.

S&F Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) 300mm long not less than 12mm dia with and incl minimum of 06 bolts and nuts, 4 on plate and 2 on staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, plate and fixed complete all as specified & directed.

S&F Aluminum anodised, barrel tower bolts of extruded section and fixed 150 mm long complete all as specified & directed

S&F extruded aluminium alloy handles 125mm size fabricated type anodized ISI marked complete all as specified & directed

S&F SS barel tower bolt 200mm long stove enamelled black with bright bolt & fixed complete all as specified & directed

S&F SS handle of 150mm size oval type stove enamelled black complete all as specified & directed.

S&F for 300 mm size MS, ordinary rat tail rod pattern springs including roller and roller plate complete frames with Screws/welding as required at site complete all as specified & directed.

S&F 140 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,with vulcanised rubber piece fixed in floor complete all as specified & directed.

S & F mild steel cupboard shutter with frame, Godrej pattern made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock vertical type size 65mm 4 lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12 mm dia bolt 150mm long grouted in brick wall/concrete including making good the disturbed surface as original complete all as specified and as directed. Note :- The measurement shall be taken of front elevation and not girthwise.

S&F in repairs Stainless Steel drapery rod of 25 mm inner dia (in length as directed ) of approved colour with & including matching finials at both ends and pair of SS brackets fixed at both ends with PVC rawl plug & steel screws on walls/beams including PVC curtain rings of matching colour @10 cm c/c including taking down complete all as specified & directed.

S&F in repairs sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, including taking down old unserviceable sink complete all as specified & directed.

S& F in repair stainless steel plate rack out of 1.00 mm thick sheet of size 900 x 750 mm and depth of shelves 230 mm with partition for small /large plates made out of stainless steel 24 gauge all as per sample to be hanged on wall by the help of steel screws grouted in walls with rawl plug design as approved by GE/Kept in GE Office

Demolition of cement concrete (reinforced) in landing slab, chullah hoods, manhole covers, Roofs, Floors, chhajja, beams, stair case, landing, chajja and similar suspended work complete all as specified & directed.

M&L for TMT bars 10mm dia and over cut to length to shape required including cranking, bending spirally or hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & directed.

M&L for form work to soffits of suspended slabs such as roof slabs etc for rough finished concrete surface complete all as specified and directed.

M&L for form work to Sides for slabs and Sides of RCC/PCC bands in walls, horizontal or sloping and SImilar work exc 10 cm but n exc 20 cm wide for fair finished concrete surface complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (Nominal mix) using 20mm graded crushed stone aggregate as in roof, floor, slabs supported on walls, water tank staging, etc complete all as specified & directed.

Demolition cement concrete (unreinforcement) in ground floor and paving n exc 15 cm thickness (below or above ground level) & removal complete all rubbish materials complete all as specified & directed.

M&L 50mm thick cement concrete 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection path laid in panel surface finished even and fair using extra cement complete all as specified and as directed

Demolition of existing roof treatment of any description including cement plaster, roof padding, APP Membrane and cement tiles any thickness from the roof surfaces of buildings including cleaning of top surfaces in all respect and preparing for further treatment and taking out and removing the rubbish, debris outside MoD land complete all as specified and as directed.

M&L PCC 1:2:4 type B1 using 20mm graded aggregate mixed with water proofing compound @ as per manufacturer instructions laid as in padding over roof slabs for providing proper slope to the concrete padding, surface finished even and smooth without using extra cement up to four stories complete all as specified & directed. (WPC shall be incl in quoted rate only nothing paid extra in this regard.)

M&L for 15mm thick screed bed on fair faces of concrete/brick surfaces in CM 1:4 with water proofing compound @ as per manufacture instruction of cement weight finished even and smooth in order to maintain proper slope over existing roof surfaces or PCC surface for laying APP based polymeric membrane finished complete all as specified & directed. (Polymeric membrane shall be meausred and paid seperately but WPC shall be incl in quoted rate only nothing paid extra in this regard.)

M&L water proofing treatement to RCC roof slab including parapet comprising of following course of treatement/specified from bottom to top (a) Applying Bituminous primer 85/25 @ 0.40 Ltr per sqm over plastered surfaces of roof including parapet surfaces. (b) Over the priming coat laying one layer APP based polymeric membrane of approved manufacturer, 3 mm thick weight not less 3.6 Kgs/Sqm and upper side of membrane thermally insulated with white mineral gravel finish, unifirmly embeded during manufacturing process shall only be used, it shall be laid by torch application . side overlap should be 75mm and end shall be 100mm. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside parapet in groove. The same shall be finished by a membrane flashing finish complete all as specified and as directed. (c) Applying two coat of Heat Resisting Paint over APP membrane as per manufacturer's instructions all as specified and as directed by Engr in charge. Note:- Only horizontal roof/chajja area shall be measured for payment purpose.

M&L plain cement concrete 1:2:4 type B0 in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified & directed.

M&L taking down and removal of loose / disintegrated old concrete up to 50mm depth/ plaster and cleaning all loose dust washing with water and applying bonding coat nito bond AR or equivlent of modified styrene butadiene emulsion (SBR bonding agent by volume with the brushes etc to bind new cement plaster/ polymer modified plaster/ concrete/ screed concrete with old surface etc complete all as specified & directed.

M&L applying 15mm thick plaster with polymer modified mortar fortified with SBR (Nitobond SBR 45) in proportion 1:3 by weight 5 litres Nit bond SBR 45 to added to 50kg cement with 13 litre water addition finished surface to match with existing adjoining surface of ceiling, beams and alike complete all as specified & directed.

M&L and applying two or more coats of 2 component zinc based epoxy rust preventer (Nitozinc Primer-M) on corroded reinforcement after cleaning and removing the rust from corroded reinforcement with the help of wire brush and treating it with rust remover (Reebaklens RR) including thoroughly cleaning washing air blowing brushing etc complete all as specified & directed. Note : Qty of zinc based epoxy rust prevent only shall be taken into account for payment purpose on the basis of actual consumption.

Taking down 15 mm bore steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

All as per srl item No 56.00 but 20mm bore.

S&F 15 mm bore GI tubing medium grade with all fitting and fixing complete to wall/floor and ceiling including concealed type in wall with cutting and chasing in wall and making good the surface in CM (1:6) & to match with the existing surfaces etc for complete all as specified and directed by Engr-in-Charge

All as per srl item No 58.00 but 20 MM bore

S & F in repair gate valves 20mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed.

Dismantling of water tanks of capacity exc 250 but n exc 500 ltrs & removing to stores complete all as specified & directed.

S&F 500 ltrs capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top)vhoilsted and fixed in position all as specified in SSR Part-I complete all as specified & directed.

S& Fixing in repair ball valve brass high pressure with polythene float and fly nut screwed on iron pipe ad fixed 20 mm bore of pipe complete all as specified & directed.

Supplying and fixing in repair for vitreous china wash down water closet pan, white (pedestal pattern) (EWC), including plastic water closet seat cover, black/white, jet spray and hand faucet of CP Brass, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, excluding flushing cistern and flush pipe complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair PVC flushing cistern low level 10 ltr cap with inlet ball valve float and handle syphonic action type incl brackets and flush pipe of polythene of low or high density ISI marked complete all as specified & directed.

S&F in repair 15mm dia bib tap cast coper alloy chromium plated fancy type crutch or butter fly handle screwed down screwed for iron pipe or for brass ferrule and fixed as fixed in repair complete all as specified & directed.

S&F in repair (one way or two way as required at site) 15mm dia stop valve/angle valve of copper alloy fancy type chromium plated screwed down high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union fixed complete all as specified & directed.

S&F in repair 15mm dia stop valve/angle valveconcealed type of copper alloy fancy type chromium plated screwed down high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union fixed in repair complete all as specified & directed.

S&F in repair swivel shower rose(fancy type) chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified & directed.

S&F in repair WHB flat back of SIze 580x450mm including,waste pipe, ss coupling, waste chain plug stopper but incl brackets incl waste pipe cutting pinning in ends of brackets complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified & directed.

S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified & directed.

S&F in repair Floor Drainer with Collar and Cockroach Trap/Jali with or without waste hole complete all as specified & directed.

S&F in repair brass chromium plated soap dish, complete all as specified & directed.

S&F in repair brass chromium plated towel ring incl a pair of CP brass bracket complete all as specified and directed by Engr-in-Charge.

S&F in repairs 15 mm bore fancy type long body bib tap, half turn, with wall flange, cast copper alloy with capstan heads, chromium plated, screwed for iron pipe or for brass ferrule, complete all as specified & as directed.

S&F in repairs glass shelf consisting of 5.5 mm thick sheets glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr In Charge.

S&F in repair CP brass mixer for WHB/Sink/Wall hot & cold water for screwed down for iron pipe and fixed bore of pipe in 15 mm including taking down complete all as specified and directed

S&F in repair PVC (SWR) pipes of 75 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.8 mm) single socketed in any length with rubber ring joints laid in trenches or in floors of 75mm pipe i/c taking out old u/s PVC/CI pipe with fittings complete all as specified & directed.

S&F in repair PVC (SWR) pipes of 110 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.8 mm) single socketed in any length with rubber ring joints laid in trenches or in floors of 75mm pipe i/c taking out old u/s PVC/CI pipe with fittings complete all as specified & directed.

S&F in repair PVC (SWR) pipes of 75 mm bore single socketed in any length fixed to wall i/c taking out old u/s PVC/CI pipe with fittings complete all as specified & directed.

S&F in repair PVC (SWR) pipes of 110 mm bore single socketed in any length fixed to wall i/c taking out old u/s PVC/CI pipe with fittings complete all as specified & directed.

S&F in repair PVC (SWR) bend 75mm bore of any radius complete all as specified & directed.

S&F in repair PVC (SWR) bend 110 mm bore of any radius complete all as specified & directed.

S&F in repair PVC (SWR) vent cowl 110 mm complete all as specified & directed.

S&F in repair UPVC (SWR) branch piece single PVC (SWR) (Single T) equal or unequal of 75 mm bore with access door complete all as specified & directed.

S&F in repair UPVC (SWR) branch piece single PVC (SWR) (Double T) equal or unequal of 110 mm bore with access door complete all as specified & directed.

S&F in repair 75mm dia PVC (SWR) floor trap, plain with grating including joining with solvent cement etc complete all as specified and directed.

S&F in repair 110mm dia PVC (SWR) gully trap, plain with grating including joining with solvent cement etc complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed stone ware,AC, or Reinforced concrete) or 100mm dia set in cement mortar including PCC bed to drain pipe, packing under & haunching against the sides of drain pipes complete all as specified & directed by Engineer-in-charge.

S&F for 75mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard, minimum load bearing capacity 5 ton/sqm, in square, rectangular or circular shape complete all as specified & as directed.

M&L 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars including demolition and breaking up old existing pipe complete all as specified & directed.

M&L for cement concrete (1:4:8) type D-2 (using 40mm graded stone agg) as bed to drain pipe including in packing under and haunching against sides of pipes after they are laid and tested in complete all as specified & directed for 100mm dia pipes.

M&L for cutting into existing manholes / Septic tank for connecting new drains/ sewage pipe after dismantled old and making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 100mm bore pipe complete all as specified & directed.

Excavating in trenches n exc 1.50m in width and n exc 1.50m in depth for foundation, manholes etc as well as n exc 10 sqmm on plan area and getting out in soft/loose soil complete all as specified & directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n exc 25 cm thick in soft/loose soil complete all as specified & directed.

Removing excavated soil to a distance exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified & directed.

S&F frame work such as grills,grating door chowkat, fencing post, flat strip etc, with ends of bars shouldered &/or riveted or forged into spikes,framed guard bars, barred iron door ladder,frame balusters,walk ways, railing, ledger,frame work or water tanks case & SImilar work including either hooks and hinges or steel hanging door fittings and including all necessary nuts and bolts and welding if reqd and hanging also fastening and fixing conforming to Fe-290 Gde E-165 incl cutting hole in wall/ floors and making good the wall/ floor surface with filled the holes alongwith PCC 1:2:4 or CM 1:4 etc complete all as per direction of Engineer-in-Charge. .

S&F welded steel wire febric n exc 4kg/Sqm etc to be fixed to wood or steel membrane with bolt or welded as required etc complete all as specified and directed

S&F for preparation of new steel surface/old untreated of any description over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws as specification including dismentling complete all as specified and directed by Engr In Charge.

M&L for Vibrator moulded (Coloured) precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade laid including dismentling complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in , path/hardstanding/subbase etc including demolition complete all as specified and directed by EIC.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

S & F factory made kitchen cabinet made out of 18mm thick PVC celuka sheet having density not less than 650kg/cum one side decorative lamination & other side balancing lamination sheet consisiting of carcase 18mm thick PVC sheet incl shutters made out of 18mm thick PVC board all required brackets 5.5 screwes etc. The panels shall be fabricated using adhesive and screws where every required. All edge shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as per drawing and specification approved by Engineer in charge. Note : (i) PVC celuka sheet manufactured by ISO 9001-2015 certified company, termite proof, water prrof & flame retradat PVC Sheet. (ii) PVC caninet of required size fabricated by joining 18mm thick PVC celuka ply fixed with each other using solvent cement adhesive and screws and 18mm thick PVC sheet as backing of cabinet to be screw and solvent cement adhesive etc (iii) The cabinet box will be devided into two equal part with two leaf shutter and one shelf will be placed in caninate (iv) Cabinate will be fixed in wall with 4 x fastners etc and necessary fixing lugs (v) Each shutter will be provided with SS handle of 75mm, CP Piano hinges, magnet/catcher (vi) The quoted rates are incl the rates of all fifftings and fixture and dismantling and taking down old kitchen cabinet of any type complete all as specifed. The measured area shall be front elevation. Note : Items like cupboard knobs, stainless steel channel, CP plate clip hinges, handles are included in the mentioned rates and as per manufacturesrs specification and drawing.The measured area shall be front elevation.

Supplying and fixing in repair factory made PVC shutter of 18 mm thickness consisting of panel of 18 mm thick celluca ply of density 600 Kg.cbm density with prelaminated sheet on one side cut in desired size of shutter and fixed with frame as in cabinet boxes with shelf and shutter full size fitted below the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc including dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. Note : Items like cupboard knobs, stainless steel channel, CP plate clip hinges are included in the mentioned rates and as per manufacturesrs specification and drawing.The measured area shall be front elevation.

M&L for anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed by Engr-in- Charge.

M&L for anti termite treatment treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed by Engr-in- Charge.

S & F for Pipe Supporting Clamping - Single Pipe of dia 4" (110 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 4" (110 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE.

S & F for Pipe Supporting Clamping - Single Pipe of dia 3" (75 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 3" (75 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No:CE Jaipur Zone; TD/2022/102. Make: Shaivi or equivalent as approved by GE.

S & F for Pipe Supporting Clamping - Single Pipe of dia 3/4" (20 mm) down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt R/M system running vertically with wall distance 3": Pipe Support Clamping made of 1. Mono Bracket for 3/4" (20 mm) pipe having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs. 2. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 3/4" pipe, Wall distance 3" - 1 Nos. 2. U Bolt R/M for 3/4" (20 mm) GI / UPVC/ CPVC pipe Dia. - 1 nos and 3. Justi Khilla 2 1/2" - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing no. : CE Jaipur Zone - Jaipur; TD/2022/102. Make : Shaivi or equivalent as approved by GE.

S & F for Pipe Supporting Clamping - Single Pipe of dia 1/2" (15 mm) down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt R/M system running vertically with wall distance 3": Pipe Support Clamping made of 1. Mono Bracket for 1/2" (15 mm) pipe having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs. 2. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 1/2" pipe, Wall distance 3" - 1 Nos. 2. U Bolt R/M for 1/2" (15 mm) GI / UPVC / CPVC pipe Dia. - 1 nos and 3. Justi Khilla 2 1/2" - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing no. : CE Jaipur Zone - Jaipur; TD/2022/102. Make : Shaivi or equivalent as approved by GE.

Taking down carefully copper/Aluminium point wiring for light/fan/socket/light fitting/power point and taking down of teak wood batten / PVC casing caping/PVC conduit/steel conduit and making good disturbed surfaces of walls/ceilings /floors etc incl dismentling of fittings.

M&L for concealed Point wiring with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with modular sheet top cover of required module with frame for mounting switches, sockets etc complete all as specified and directed. Note -(a) Quoted rates shall be deemed to include the cost of Cutting Chases in Stone/Brick wall and making good to the disturbed surfaces including plastering and painting to match with the existing colour. (b) The rates Quoted by the contractor shall be deemed to include the cost of modular cover plates of required module with frame, cost of Sheet Metal Box and no additional payment shall be made on account of the same.

All as per srl item No 115.00 but for one fan point controlled by one switch and regulator

All as per srl item No 115.00 but for one exhaust fan point/Fresh Air Fan Point controlled by one switch.

All as per srl item No 115.00 but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per srl item No 115.00 but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per srl item No 115.00 but for one bell/buzzer point controlled by one bell push

All as per srl item No 115.00 but for one light point controlled by two way switches

All as per srl item No 115.00 but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade as continuous earth wire in green colour.

All as per srl item No 115.00 but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4.0 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade including 4.0 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade as continuous earth wire in green colour.

Supply and fixing Modular switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts complete all as specified and directed.

S&F modular switch piano flush type single pole two way 5 Amps 230 Volts complete all as specified and directed.

S&F modular bell push flush type 5 Amps 240 V complete all as specified & directed.

S&F in repair Modular bell/buzzer AC 230 volts single pole complete all as specified & directed.

Supply and fixing modular switch piano, flush type, single pole, one way, 15 Amp, 230 Volts complete all as specified and directed.

Supply and fixing modular socket outlet, 3 pin (with 2 pin outlet also), 5/6 Amp, flush type, 240 Volts complete all as specified and directed.

Supply and fixing modular socket outlet, 2 in 1, 3 pin, 5 and 15 Amp, flush type, 240 Volts complete all as specified and directed.

Supply and fixing modular ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed.

Supply and fix in repair LED batten (1.2m) made of CRCA sheet housing with a PC glossy diffisure duly prewired connection having nominal system lumen output of 2000 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 20 watt including driver. it should have rated system life time of 40000 burning hours at L70 and should have a temperature of 6500 K CRI >80, thd <10 and PF>0.95 complete all as specified and directed. Make - Crompton Cat Part CIS-305-40-57-SL-DP-NWH, Philips Cat part BN308C LED20S-6500 L120 PSU WH, Havells Cat Part Stella 20 Watt Galmtube LHEWAJPGPV1D020

Supply and fixing in repair lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and Fixing in repair 20 watt emergency LED inverter bulb B-22 capacity with inbuilt powerful lithium battery backup of atleast 4 hours and having minimum two years warranty. The lighting shall have deep discharge protection, fast charging, offering cool day light for atleast four hours in off hours complete all as specified and directed. Make : - Havells/Philips/Bajaj

Supply and fix in repair wall mounted decorative lamp holder aesthetically designed with elegant frosted glass casing in durable metallic housing inbuilt with bulb holder two pin or Screwed type including insulated body with back plate for angle/batten fitting complete all as specified and as directed. Make/Model : Havells : Floretine WL1LSE27SSLHFOAJD1TZ1I060/Phillips Nerobless/Bajaj/Crompton

Supply and fixing in repair sheet metal enclosures double door type suitable for fixing MCB's, SPN with 200 Amps rated bus bar, 8 way, 240 Volts complete all as specified and directed.

S&F in repair MCB 32/40 Amp, single pole & neutral, 240 Volt complete all as pecified & directed.

S&F in repair MCB 6-40 Amp, single pole 240 Volt complete all as pecified & directed.

Supply and fixing in repair Vertical sheet metal enclosures double door type , suitable for fixing MCB, TPN with 200 amps rated bus bar, 4 way. 415 Volts with inbuilt MCCB 4 pole 63 Amp,16 KA complete all as specified and directed.

S&F sub main wiring on and including passing through PVC conduit in concealed (including cutting chasis in stone/brick wall) 1100 Volts grade with PVC flexible cable copper conductor cable fire resistant low smoke and halogen (FRLSH) unsheathed multistranded single core of size 6 sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 sqmm of green colour confirming to IS 694/1990 including taking down existing U/S sub main wiring complete all as specified and directed. (Note: Two runs of cable with one run of earth wire and one run of PVC Coundit should measured as one length)

Material and labour in replacement for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & directed. Note : - Quoted rate shall be deemed to include for earth wire with protection pipe up to 7.5 meter length.

M/L for GI pipe (Light grade) for protection of LT cable fixed to walls/ poles/road crossing including clamps complete of 40 mm bore complete all as specified and directed.

Supply and fixing of 25 mm bore GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe complete all as specified and directed.

M & L for fixing in repair Gun-metal, globe or gate valves, 25 mm bore of pipe with iron wheel head, screwed both ends with GI Union for iron pipe and fixed complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 25 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified & directed. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

M/L for brick work with FLY ASH BRICKS(As Per IS-13757(1993) burnt clay fly ash building bricks), (OLD SIZE BRICKS) laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection and complete all as specified & directed.

M&L for dry sand and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

Disconnecting form elect connection and taking down carefully the existing Ceiling fan/Exhaust fan/Geyser of any capacity, any make,any size and depositing same the Ceiling fan/Exhaust fan/Geyser in AGE E/M store yard all as specified and directed by the Engineer-in-Charge.Refixing the same Ceiling fan/Exhaust fan/Geyser carefully incl necessary electric connections complete all as directed.