REPAIRS TO JOINERY, ALUMINIUM DOORS/VENTILATORS, STEEL WINDOWS/VENTILATORS, CUP BOARDS, ROLLING SHUTTERS, STEEL DOORS, PVC DOORS ETC AND OTHER CONNECTED WORKS AT MD ACCN AT CME

Amount

Taking down Chowkats or Frames, not exc. 1.50 Sqm Each with Shutters (without Taking Off Shutters from the Frames), complete all as specified and as directed.

Taking down Chowkats or Frames, exc. 1.50 Sqm but not exc. 4.00 Sqm Each with Shutters (without Taking Off Shutters from the Frames), complete all as specified and as directed.

Taking down shutters only of size exc 1.00 Sqm but not exceeding 4.00 Sqm

Taking down Chowkats or Frames, exc. 1.50 Sqm, with Shutters (without Taking Off Shutters from the Frames), complete all as specified and as directed.

S&F 2nd class hard wood plain solid straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamferred, put to gether with glue pinned at joints supplied and fixed

M&L preparing surfaces of wood and wood based and treating ends of posts, back of chowkats. Etc area exc 0.1 sqm but n.exc 0.5 sqm each complete all, as spcified and directed.

S& fixed factory made plain framed paneled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edges or panel of 9mm BWP commercial ply over 12mm thick veneered panticle board with commercial face veneers fixed to chowkhat . The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure treated complete all as spfd.

S&F 30mm thick flush shutter, solid core construction, with block board core and both face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

S& fixed 2nd class hard wood 35 mm thick made glazed and skeleton shutters open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) complete all as spfd

Mild Steel works as in bands straps, hold fasts etc, conforming to IS-2062-2006 (Fe-290), embedded portion duly painted with bituminious paint and sanded, complete all as specified.

Preparing surface of iron and treating small articles such as stop, covers, gully grating, holdfasts, end of posts area exc 0.1 Sqm each complete all as specified and directed.

Cement concrete type B1 (1:2:4) using 20mm grades stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as spd.

S&F PVC Solid Door Frame of Size 50X47mm made out of 5.0mm Plain Colour PVC Sheet Reinforced with Mild Steel Square Tube as specified Manufacture’s Instructions complete all as specified and as directed.

S&F Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Tubes for Top and Bottom Rails, Mild Steel Frame shall be covered with heat moulded Plain Colour PVC 'C' Channel having a PVC Sheet Strip of 20mm width stuck inside with Solvent Cement for Stiles and Plain Colour PVC Sheet for Top Rail, Lock Rail and Bottom Rail on either Side and as Gap insert for Top Rails & Bottom Rail, Panelling of Plain Colour PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles and Rails with suitable PVC Sheet Beading and Joined together with Solvent Cement and fixing in the Frame at Site as per Specifications and Draw-ings, complete all as specified and as directed.

S&F factory made steel windows with two shutter (Glass & Wiremesh) with side hung shuters including projecting type hinges with steel handles,4mm glass, wiremesh grill and steel peg stay complete with glazing bars dovetailed or welded and painting over primeg complete all as specified and directed ..

S&F factory made steel ventilators top hung two shutters(Glass & Wiremesh) including projecting type hinges with steel handles,4mm glass, wiremesh,grill and steel peg stay complete with glazing bars and painting over primer complete all as specified .

M&L for Preparing New Wood and Wood Based Surfaces of any description, over 100mm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Coat of Pink Primer, complete all as specified and as directed.

Dismantling Wrought Iron or Mild Steel Work, viz. Mild Steel Flat Iron, Mild Steel Bars, Bends, Straps and Similar Work including Mild Steel Bolts, Nuts, etc., fixing to RCC Fencing Posts, Struts, etc. complete all as specified and as directed.

S & F for framed work such as grills or grating etc with ends ofr bars shouldered as framed guard bars conforming to Fe-290 Gde E- 165 all as specified and directed.

M&L for Preparing old Wood and Wood Based Surfaces of any description, over 100mm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) complete all as specified and as directed.

M&L preparing New Steel and Iron Surfaces of any descriptions, over 100mm in width or girth and applying Two Coats of Synthetic Enamel Paint over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L preparing old Steel and Iron Surfaces of any descriptions, over 100mm in width or girth and applying Two Coats of Synthetic Enamel Paint , complete all as specified and as directed.

S & F Mild steel butt hinges medium weight , cold rolled, 100mm, ISI marked, complete all as spd .

M&L barrel tower bolts stove enamelled black of size 200 mm complete all as spd .

S & F Mild steel pressed handles, oval type,stove enamelled black

S/F 150mm long Aluminium handles, cast type anodised

S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete.

S&F 300mm long Aluninium alloy, anodised , sliding door bolt with hasp , staple,(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F 300 mm Mild steel sliding door bolts,plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed

S&F stainless Steel Wire Cloth, 0.36mm nominal dia of Wire and average width of aperture 1.4 mm and fixed with Tinned Tacks of Mild Steel Wire Stapes, fixing etc, complete all as specified and as directed.

S&F stainless Steel Wire Cloth, 0.36mm nominal dia of Wire and average width of aperture 1.4 mm and fixed with Tinned Tacks of Mild Steel Wire Stapes, fixing and repair etc, complete all as specified and as directed.

S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate . fixing and repair etc complete all as specified and directed.

S&F in repair 150mm dia double legged door stopper of aluminium alloy with rubber complete all as specified and directed.

Fixing in repairs Mortise Lock of size 100mm, Brass Body, Verical Type, 12 Lever and fixing to Aluminium Ahutter with Necessary Fittings as required/ordered at sites(s) complete and fixed inrepairs all as specified and as directed.

S&F Double Action Floor Spring Hydraulically Regulated made up of minimum 1.25mm thick Aluminium Alloy sheet foundation Box, Main Body with stainless steel cover, outer ring pivot made of brass, other part made Mild steel heavy duty and fixing to Aluminium Shutters with necessary fittings as required/ ordered at site(s), complete and fixed inrepairs all as specified and as directed. Make: Sandhu

Fixing in repair door closer of aluminium (extruded section body) hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete as specified and directed by Engr-in-Charge.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares of any size complete all as specified and directed by Engr-in-Charge.Make: Modhi Gold

S&F 3mm thick figured glass pin head type and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqmtr each pane complete all as specified and directed by Engr-in-Charge.Make: Modhi Gold

S&F aluminum powder coated fixed partition with frame of size 101.6mm x 44.45mmx1.27mm thick and 101.60mmx44.45mmx1.20mm thick with total height 3.20m. The panels shall be made out of 5mm thick plain /tinted(frosted) glass in top & bottm of 12 mm thick both side laminated particle board(i.e 50-50) including door with acceries i.e floorspring,hydrolic door closer, buttings, handle tower bolt, necessary jointing cleats, glazing clips , rubber packing, powder coated aluminum snap beading screw etc including making good to the disturbed portion complete all as specified and directed.

S&F aluminium colour powder coated anodised door and shutter single or double leaf glazed/pre laminated board exterior quality partly glazed//pre laminated board exterior quality party glazed panels fabricated including aluminium anodised beading rubber and packing materials and shall be drilling in existing wall and thrust bolt suitable size complete comprising the following:- (a) Aluminium colour anidised door frame section 101.60x44.45x1.93 mm fixed as per spd (b) Aluminium colour anodised vertical section in shutter 85x44.45x2 mm as per spd. (c) Aluminium colour anodised Top & style shutter section 95.25x44.45x2.00 mm as per spd. (d) Aluminium colour anodised handle 02 Nos in each shutter 200 mm long as spd. (e) Aluminium colour anodised middle lock rail/bottom rail section 150x44.2.65mm cat No.20002.Make-Jindal (f) Floor spring Make-Sandhu, (g) Six lever mortice lock brass Make : Godrej/Classic on in each door (h) 12 mm thick particlular board (pre laminated both face) exterior grade ISI Marked (j) Tinted glass/Plain glass(Colour) 5mm thick Make : Saint gobain midgaurd (k) Floor spring , Make Sandu Note : If ground requirement for full glass or full Panel contractor should provide as per direction of Engr-in-Charge.

S&F for aluminum anodized three track slinding window with two or more shutter with 4 mm thick plane glass, one shutter of stainless steel mosquito proofing with good quality bearing ,handle lock,etc rubber beading and glazing clips etc using following sections as given in 'JINDAL' catlogue including taking down existing old window of any description complete all as sspecified and directed.

S&F aluminium anodised louvered ventilator with 4 mm thick pin headed glass and 100 mm wide glass strips, white framed and fixed with aluminium anodised frames etc including taking down existing old window of any description complete all as sspecified and directed.

S&F in repair Veneered decorateive plywood, grade 1 (with BWR resin) with decorate face veneers on both faces; fixed with screws to timber frame work Make : Duro/National

M&L 12 mm plywood grade BWR, type BB, fixed with screws to timber frame work and fixed in repairs

M&L 6 mm plywood grade BWR, type BB, fixed with screws to timber frame work and fixed in repairs

Sanding newly tarred or painted surfaces with clean sharp sand complete all as specified and directed

Resecuring or easing & adjusting , without taking down of shutter in the same opening of any description and size complete all as specified and directed.

M&L 18/19mm thick Pre-laminated board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination , fixed with screw to timber frame including taking down existing board of any description complete all as specified and directed.

M&L cover fillet (lipping) of tempered hard board 40mm wide, 6mm thick and fixing with screw complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) in 30mm complete all as specified and directed.

S&F 40mm dia cupboard knobs fixed with nut, screws and washers of mild steel bright finish complete all as specified and directed.

S&F 150mm hasp and staple, mild steel, wire type stove enamelled black, including bolt to hinge plate and fixed with screw.complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation boards/slabs/blankets, any thickness, including cover fillets

M & L for false ceiling with 4mm thick designer 'E' board fixed on GI grid work with powder coated finish on exposed surface of size 0.6 x 0.6m consisting of GI angle supported on wall of size 24mm x 28 x 0.7mm main tee of size 24mm x38mm x 0.7mm cross tee of size 24mm x 28mm x 0.7 mm using porpose made members interlocking to each other and with 40mm x 3mm flat GI mild steel strip suspender made to shape at 1200mm c/c fixed with 3mm dia GI wire and making holes etc all as directed including two coats of white wash on ceiling after preparation of surfaces and as per manufacture instruction make of GI Grid work : Armstrong/Swastik/Techno Grid and Make E board Gypsum or equivalent approved .

Dismantling boarding , any description in any position with nails complete

M&L 2nd class hardwood clean sawn weather boarding, plain, 20mm thick or feather edged 15mm to 20mm thick and fixed with 30mm laps complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises

M&L Glazed Ceramic Coloured Tiles, 300X450X7mm to 10mm in size, set on Vertical Surfaces such as Skirting, Dado, etc,over and including 10mm thick screed bed in cement mortar 1:3 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, complete all as specified and as directed.

M&L Non–Skid Coloured Tiles, size600x600x10 mm in size, Laid on Floor, Laid and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles,incl. Screed Bed or Bedding Layer 15mm thick as in Floor in Cement Mortar 1:6 complete all as specified and as directed.

M&L Non–Skid Coloured Tiles, size600x200x10mm in size, vertical Laid and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles,incl. Screed Bed or Bedding Layer 15mm thick as in Floor in Cement Mortar 1:3 complete all as specified and as directed.

M&L for granite 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing etc,laid over 15mm thick screed bed in cement mortar 1:6 Laid and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles,complete all as specified and as directed

M&L for Vitrified Ceramic tiles 10 mm thick Colour (square/rectangular) polished, area of each tiles exc .18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including Screed Bed 15 mm thick in Cement Mortar (1:6) complete all as specified and as directed.

S&F 1.25mm thick steel rolling shutters, without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in positionas indicated complete push pull or manual type including locking arrangement(Safety lever locks mild steel with 4 levers for rolling shutters) , two coats of synthetic enamelled paint over a coat of red oxide including taking down old rolling shutter of any description and size complete all as specified and directed.

Repairing to existing rolling shutter of any description and size by replacing ball bearing safety lever lock, replacement of PGI sheet and making fuctional by greasing etc complete all as specified and directed.

S&F steel door including projecting type hinges, steel handle, locking device including steel frame for door shutter with glazing bards, dovetailed or welded including dismantling old steel door of any description and size complete all as specified and directed .

S&F 0.63mm thick CGI sheeting with two corrugation side lap, fixed with coach screws and washers, in roof, walls etc including dismantling of existing sheet of any description complete all as specified and directed.

S&F 0.63mm PGI sheeting in ridge, hips, valley gutters, drips and straight flashing etc including dismantling of existing sheet of any description complete all, as specified and directed.

M&L Welding in repairs n. exc 2.5cm in length to old doors for fixing hinges, tower bolt, sliding door bolt, handles, locking system, etc complete all as specified and directed.

S&F fixed in repairs aluminium sheet 0.56 mm th fixed to door shutters with nails all as directed by Engr-in-Charge.

(Applicable for above all items)

(a). Contrator has to employ skilled/unskilled tradesman with adequate experience & required documents to be submitted to office.

(b). Labour should wear contractors uniform with firm logo, failing which recovery should be made.

(c). Minimum of 02 x teams of each trades shall be available for maint of urgent nature whenever called upon of any trade, failing which recovery will be initiated for not employing adequate labour at site.

(d) Site clearance shall be done by contractor after finishing work.

(e) All Scarps will be done with mechanical scaper

(f) Mechanical scaper should be deposit in our store at the time of sample approval

S.K.HARAL

GB Infrastructures