Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹54.4 CrAccepted-AOC | ₹54.4 Cr | L1 | Accepted-AOC L1 bidder |
| 2 | L2₹54.5 CrRejected-Finance | ₹54.5 Cr | L2 | Rejected-Finance Higher bid value |
Tender Value
Refer Docs
Closing Date
27 Jul 2021, 4:00 pmClosed
SRI S K GHOSH, DCPL
Development Consultants Pvt Ltd, Development Consultants House, 4th Floor Block DG4,Sector II, Salt Lake City, Kolkata 700091
SITE n INFRASTRUCTURE PACKAGE FOR ALTERNATIVE ARRANGEMENT FOR SOURCING OF BAUXITE FROM PANCHPATMALI MINE FOR STREAM -5 OF ALUMINA REFINERY, MnR COMPLEX AT DAMANJODI, ODISHA
2021_NALCO_637359_1
NALCO/DCPL/MINES/2021/SnIP/05
Open Tender
Civil Works
605 days
DAMANJODI
As per NIT
2 documents required · 2 mandatory
₹0
Exempted
7 Aug 2023
7 Jul 2021
28 Jul 2021
7 Jul 2021
27 Jul 2021
15 Jul 2021
7 Jul 2021 - 14 Jul 2021
Amount
Earth work
Excavation work in all kinds of soil by pick axes or spades or hydraulic excavator in foundations, pits, trenches,reservoirs,drains etc. including de-watering, dressing at sides and ramming at bottom lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil to stack or fill in the adjoining area within a lead of 1000 m . ( Only PCC plan area as per drawing shall be measured for payment).
Same as above item no.1.01, but lift beyond 1.5 m upto 3.0 m
Excavation work in ordinary rock by mechanical means( Hydraulic excavator)/manual means in foundations, trenches, reservoirs, drains etc. including dewatering,dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil to stack or fill in the adjoining area or as directed, within a lead of 1000 m.( Only PCC plan area as per drawing shall be measured for payment).
Same as above item no.1.03, but lift beyond 1.5 m upto 3.0 m
Filling the available excavted earth/ laterite (to be broken into pieces of not larger than 150 mm excluding rock) in trenches, plinths, sides of foundations etc. in layers not exceeding 20 cm in depth with proper compaction so as to achieve a standard proctor density of not less than 85% for each deposited layer by ramming and watering.
Extra over item no. 1.01 to 1.04 for disposal of excavated earth & ordinary rock beyond initial lead of 1000 m and upto 2000 m complete in all respect as per specification and instruction of E.I.C.
Supplying and filling in plinths with sand under floors, including watering,ramming,consolidating and dressing complete.
Supplying and filling river sand of approved quality for 50 mm thick over prepared bund slopes and reservoir bed including screening, compacting, watering, etc. complete as directed with all leads and lifts.
Surface dressing in all kind of soil of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 500 m and lift upto 1.5 m
Stone work
Providing and laying boulder soling of approved quality and size below grade slabs to thickness of 250mm carried out in layers with interstices between the stones wedged in with smaller stones of suitable size, coarse aggregate of size 100mm to 150 mm and down and sand filled in interstices including cost of sand and coarse aggregates, its transportation, loading, unloading, compacting, all labour, equipment, etc. complete.
HDPE film
Supplying and Laying of 250 micron HDPE (High Density Polyethylene) film as per Technical Parameter indicated in Specification, inclusive of procurement, packing, transportation to site, proper storage, laying over sand blanket in the base of Reservoir as well as on sidess of the embankment to prevent seepage including joining with approved method, fixing at top of embankment and bed of reservoir by forming a trench as shown in the drawing etc all complete as per specification and as directed by the Engineer. Minimum width of HDPE liner shall be 6m. ( Measurement will be as per actual spread area. Laps and anchoring area will not be considered)
Concrete Work (PCC / RCC / PRECAST)
Providing and laying precast cement concrete tiles 75mm thick (300mm X 300mm) of grade M20 pointed with cement mortar 1:4 over sand bedding on bund slopes, reservoir base, intermediate benching, etc including making necessary casting yard, form work, watering, curing, transporting, stacking etc. complete with all leads and lifts.
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All works upto plinth level :1:3:6 (1: cement:3 coarse sand: 6 graded stone aggregate 20 mm nominal size)
Providing and laying in position machine batched and machine mixed design mix M 25 grade cement concrete for RCC works, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixures in recommended proportions as per IS: 9103 to acelerate,retard,setting of concrete, improve workability without impairing strength and durability as per directions Engineer-in-charge. Note :- Cement content considered in this item is @330 kg/cum.Excess/less cement used as per design mix is payable/recoverable separately: All works upto plinth level
All works as per 4.03 for above plinth level.
Steel reinforcement for RCC work including straightening, bending, placing in position and binding all complete : Cold twisted bars conforming IS:1786
Supplying, installing, dismantling and removing following classes / class of formworks for foundation & sub-structures in all kinds of work including necessary rendering of concrete surfaces after exposure as per drawings, specification and direction of Engineer : Steel / Plywood
Supplying, installing, dismantling and removing following classes / class of formworks for super-structures including necessary rendering of concrete surfaces after exposure as per drawings, specification and direction of Engineer : Steel / plywood
Providing and laying in position specified grade of reinforced cement concrete slab on grade excluding the costs of centering,shuttering,finishing and reinforcement- All work upto plinth level : 1:1.5:3 (1: cement:1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size)
Manufacture and erection in position reinforced pre-cast concrete units of every description, shape, size in M-25 grade concrete with minimum cement content as per specification and approved drawings including all formwork, pockets, slits, slots, cutouts etc. for lifting hook or surface drainage etc including cost of material labour etc. (The cost of reinforcement will be paid under seperate item).
Supplying grouting materials and grouting under column & Equipment fdn base etc. using following flowable grout including preparation of concrete surfaces complete as per specification and instruction of Engineer ( No formwork to be paid separately): Non-shrink grout of approved make ( Combextra GP2 or equivalent)
Providing and laying damp proof course 50 mm thick with cement concrete M20 with approved waterproofing admixture below the concrete block masonry work at Plinth level.
Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes below the concrete block masonry work at Plinth level.
Structural steel work
Supply, fabrication and Erection of structural Steel works in single or builtup sections as per drawing including tools, tackles, cutting, welding, consumables, assembly, bolts, permanent bolts, preparation of fabrication drawings for all types of structures in buildings, pipe racks, platforms, towers or any other structure as specified in Technical specification and drawing and applying a priming coat of approved steel primer, complete in all respect.
Supply, fabrication and Erection of structural Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. all complete : Electric resistance or induction butt welded tubes
Finishing with epoxy paint ( two or more coats) on steel work at all locations prepared and applied as per manufacturer,s specification including appropriate priming coat, preparation of surface, etc.complete.
Supplying, fabricating, handling and laying in position of insert plates, angles etc. complete with all lugs including welding at all levels as per specification/ drawing
Providing, fixing mild steel round holding down bolts with nuts & washer plate complete
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balconi railing, staircase railing and similar works including applying priming coat of approved steel primer : E.R.W tubes
Road Work
Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres as per specification/drawing.
Cutting road and making good the same including supply of extra quantities of materials i.e aggregrates, moorum screening, red bajri and labour required : Water bound macadam
Brick edging laid lengthwise with half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres :With common burnt clay F.P.S ( non modular bricks) of class designation 7.5
Providing and laying bitumen penetration macadam with hard stone aggregate of quality, size and grading as specified, with bitumen of suitable penetration of grade,including required key aggregate as specified, spreading coarse aggregate with the help of self propelled tipper tail mounted aggregate spreader and applying bitumen by a pressure distributor and then spreading key aggregate with the help of aggregare spreader complete, including consolidation with road roller of minimum 8 to 10 tonne capacity to achieve a specified values of compaction surface accuracy :For 75 mm compacted thickness in two layers using stone aggregate of size 63-41 mm graded @ 0.90 cum per 10 sqm key aggregate of size 20 mm graded @0.18 cum per 10 sqm. With paving asphalt grade VG-10 @ 68 kg/10 sqm.
MASONRY WORK
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) sqm
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in : Cement mortar 1:6 (1 cement : 6 coarse sand)
Brick work with fly ash bricks conforming to IS:12894,. (non modular) brick of class designation 10 in superstructure above plinth level in : Cement mortar 1:6 (1 cement : 6 coarse sand)
Half brick masonry with fly ash bricks of class designation 10, conformingio IS :12894 (non modular) in superstructure : Cement mortar 1:4 (1 cement :4 coarse sand)
Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.
FINISHING
12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)
15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand
6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)
20 mm cement plaster 1:2 (1 cement : 2 stone dust).
Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade :New work (Two or more coats applied @ 1.43 ltr/ 10sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)
Providing neat cement punning.
Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.
Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade. New work (two or more coats) over and including water thinnable priming coat with cement primer
Applying priming coat : With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat)
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture
White washing with lime to give an even shade :New work (three or more coats)
Finishing internal Wall with (two or more coats) acrylic emulsion paint of approved brand and manufacture on new work to give an even shade on primer (Primer to be paid separately)
Applying one coat of primer of approved brand and as recommended by the paint manufacture, on wall surface.
Providing plaster drip course/ groove in plastered surface or moulding to R.C.C. projections
Providing and fixing of 300mm wide chicken wire Plaster mesh made out of galvanized iron of nominal thickness 0.35 mm with a Zinc coating of 120 gms per Sqm at the junctions of Masonry and concrete works, chasing Works, diagonal fixing at corners of Doors & Windows openings including tying in position with suitable nails / screws etc. complete all as per manufacturer specification. The rate shall include for preparation of surface, cleaning, curing, double scaffolding etc. complete all as per specifications and directions of the Engineer-in-Charge.
DOOR AND WINDOW
30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire-retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames
Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.
Providing and fixing chromium plated brass butt hinges with necessary chromium plated brass screws etc. complete : 125x70x4 mm (ordinary type)
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately): Sal wood
Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : 125x65x2.12 mm
Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm
Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).
Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :200x10 mm
Providing and fixing bright finished brass handles with screws etc. complete: 125 mm
Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. ii) Grill weighing above 16 Kg./sq.mtr and above
Providing and fixing bright finished brass hasp and staple (safety type) with necessary screws etc. complete : 150 mm
Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters: 80x1.25 mm M.S. laths with 1.25 mm thick top cover
STEEL WORK
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
Providing and fixing bolts including nuts and washers complete.
FLOORING
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry,but excluding the cost of nosing of steps etc. complete: 40 mm thick with 20 mm nominal size stone aggregate
52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per anufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.
Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement: 18 mm thick
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge: Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete: Size of Tile 600x600 mm
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
ALUMINIUM WORK
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion-Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineerin-charge complete. 355 X 19 mm
Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge : Powder coated minimum thickness 50 micron aluminium tubular handle bar
Providing and fixing 100 mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.
Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete : Upto 5mm depth and 5 mm width.
Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete : Anodized (AC 15) aluminium
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) :With float glass panes of 8.0 mm thickness
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) :With float glass panes of 4.0 mm thickness
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) :With float glass panes of 5.0 mm thickness
Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness
DRAINAGE
Construction of cement concrete drain minimum 30 cm wide and will vary according to slope and avarage 47.5cm deep in cement concrete M20 having 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete.
Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.
Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :150 mm dia SW pipes
Constructing brick masonry manhole with 2nd class bricks in cement mortar 1: 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 :8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size)inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design : Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg,(weight of cover 23 Kg and weight of frame 15 Kg).
WATER SUPPLY :
INTERNAL WORK - EXPOSED ON WALL Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge : for 1216 (16 mm OD) pipe
Same as 14.01 for 1620 (20 mm OD) pipe
Same as 14.01 for 2025 (25 mm OD) pipe
Same as 14.01 for 2532 (32 mm OD) pipe
Same as 14.01 for 3240 (40 mm OD) pipe
Same as 14.01 for 4050 (50 mm OD) pipe
CONCEALED WORK, including cutting chases and making good the wall etc. Providing and fixing Polyethelene-Aluminium- Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge : For 1216 (16 mm OD) pipe
Same as 14.07 for 1620 (20 mm OD) pipe
Same as 14.07 for 2025 (25 mm OD) pipe
Same as 14.07 for 2532 (32 mm OD) pipe
EXTERNAL WORK - EXPOSED ON WALL Providing and fixing Polyethelene-Aluminium- Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge : For 1216 (16 mm OD) pipe
Same as 14.11 for 1620 (20 mm OD) pipe
Same as 14.11 for 2025 (25 mm OD) pipe
Same as 14.11 for 2532 (32 mm OD) pipe
Same as 14.11 for 3240 (40 mm OD) pipe
Same as 14.11 for 4050 (50 mm OD) pipe
Providing and fixing brass bib cock of approved quality : 15 mm nominal bore
Providing and fixing brass full way valve with wheel of approved quality : 40 mm nominal bore
Providing and fixing brass full way valve with wheel of approved quality : 50 mm nominal bore
Providing and fixing brass full way valve with wheel of approved quality : 65 mm nominal bore
Providing and fixing brass stop cock of approved quality : 15 mm nominal bore
Providing and fixing PVC connection pipe with brass union-45 cm length, 15 mm nominal bore
Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet : 100 mm dia
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms : 15 mm nominal bore
SANITARY INSTALLATION
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked black solid plastic seat and lid
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : Range of three urinal basins with 10litre white P.V.C.automatic flushing cistern
Same as 15.02 for Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board - 510x1040 mm bowl depth 250 mm
Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required : White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality.
Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer in- charge.
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.
Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleats with CP brass screws.
Providing and fixing toilet paper holder : C.P. Brass
Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet- Sand cast iron S&S as per IS: 3989
Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729
Providing and fixing soil, waste and vent pipes : 75 mm diameter :Sand cast iron S&S pipe as per IS: 1729
Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : For 75 mm dia pipe
Same as 15.16 for 100 mm dia pipe
Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100 mm dia pipe
Same as 15.18 For 75 mm dia pipe
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100 mm dia Sand cast iron S&S as per IS - 1729
Providing and fixing plain bend of required degree- 100 mm dia Sand cast iron S&S as per IS - 1729
Providing and fixing heel rest sanitary bend : 100 mm dia Sand cast iron S&S as per IS - 1729
Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks of class designation 7.5 or above in cement mortar 1:4 (1 cement : 4coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 455x610 mm and 45 cm deep for single pipe line :
Supply fitting, fixing cast iron down pipes conforming to IS:3989-1970 and IS:1729-1964 in position with necessary clamps, nails including making hole in wall, floor etc. and cutting trenches in any soil through masonry concrete structures etc. if necessary and mending good damages including joining with jointing materials complete.[ Payment will be made on centre line measurement of the total pipe line including specials. Payment for specials will however be paid separately ] : 150 mm diameter pipe
Supplying fitting fixing C.I. Specials of down pipes in position with clamps nails etc. with jointing materials including cutting holes in masonry or concrete, mending good damages complete : CI Plain bend-150 mm diameter
Supplying fitting fixing C.I. Specials of down pipes in position with clamps nails etc. with jointing materials including cutting holes in masonry or concrete, mending good damages complete : CI Plain shoes : 150 mm diameter
Supplying, fitting and fixing Half round channel with or without outlet as required set in cement concrete (6:3:1) with jhama chips complete :Salt glazed stone ware -600 mm X 100 mm. (Payment of concrete will be paid seperately).
Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleat with CP brass screws (heavy quality) : 750 x 20 mm size
ROOF WATERPROOFING
Providing and applying combination of waterproofing & insulation, in the following sequence thru In-House Application Arm of Manufacturer by Spray apply an average 40 mm thick two component Hydro flouro carbon(CFC free), polymeric M.D.I based closed cell(96-98% as per ASTM D2856) multilayer, waterproof insulative polyurethane foam, and Providing and applying a sealer coat,, which is a single component cold applied elastomeric waterproofing coating with >=500% elongation confirming to ASTM C836 applied by a brush/roller in 2 coats and finished with loosely lay 120-150 GSM geotextile(non-woven polyester) over the Elastomeric coating. Laying protective slope with M20 grade fibrated screed (admixed with integral liquid waterproofing compound conforming to IS:2645). Green stage saw cutting on the screed will be done in panels(3mx4m) with grooves 10mmx10mm. Finally the groove will be sealed with suitable elastomeric sealant.
All around on the roof, at the parapet wall junction, an angular fillet 50mm x 50mm shall be trowel applied in cement-sand mortar(cement, sand mortar shall be supplied by you) in 1:3 proportion. A latex based bonding agent should be added (10% by weight of cement) and also a glass cloth must be inserted around the junctions while the angle fillet is being constructed.
VERTICAL SURFACE TREATMENT
Surface preparation, minor cleaning works, removal of loose concrete, laitance, dust particles, etc and filling cracks with polymer modified mortar using latex based bonding agent. Removal of algae if present is to be done. Providing and applying a water based acrylic primer ,over the entire surface of the parapet walls(2 part primer : 1 part water). Providing and applying 2 coats of a high performance elastomeric coating, composed of acrylic emulsion polymers.
FALSE CEILING
Providing and fixing 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks) false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats , G.I. channels , including fixing perimeter channels , including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting
Providing and fixing perforated Aluminium Panel ceiling manufactured by approved brand, of approved colour consisting of Panel 84mm wide x 16mm deep x 0.5mm thick, with round edges, enamelled corrosion resistance aluminium alloy AA 3105( Al.Mg.) . Panel shall be clipped to a baked enamelled aluminium panel carrier of 62mm wide x 29mm deep made of 0.95mm thick in standard length of 5 mtr made of double baked enamelled aluminium alloy AA5050 (Al.Mg.). The Carrier shall be suspended by means of G.I. suspension rod 4mm diameter, and a Galvanised Suspension Spring Clip at a distance of 1.3mtr c/c. Top of panels shall be laid with PET wool blanket of 25mm thick, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge
FIRE RATED DOOR : Providing and fixing of Hollow metal fire rated doors at all levels as per IS 3614 part-1 & part-2 for stability and integrity. Pressed Galvanized steel confirming to IS 277 . Recommended fire door shall have doors tested at CBRI or ARAI for maximum rating of 2hrs with vision panel. Door frame shall be double rebate profile of size 143 x 57 mm made out of 1.60mm (16gauge) minimum thick galvanized steel sheet. Door leaf shall be 46mm thick fully flush double skin door with or without vision lite. Door leaf shall be manufactured from 1.2mm (18guage) minimum thick galvanised steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be resin bonded honeycomb core. All doors shall be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. All doors and frames shall be finished with etched primer coating, stove zinc phosphate primer and thermosetting polyurethane aliphatic grade paint of approved colour. The door leaf and frame shall have passed minimum 250 hours of salt sprey test.
Hollow Metal Door (Without Fire Rated) : Providing and fixing of hollow metal door at all levels from ISO 9001-2000 certified manufacturer. All hollow metal genaral doors with or without vision panel. Pressed Galvanised steel Single / Double leaf to required sizes of approved make which consists of frame, shutter, infill and finish as detailed below and conforming to IS 277. Door frame shall be single rebate profile of size 100x57mm made out of 1.20mm thick galvanised steel sheet (18gauge). Door leaf should be 46mm thick fully flush double skin door with or without vision lite. Door leaf shall be manufactured from 0.8mm (22 gauge) minimum thick galvanised steel sheet. The internal construction of the door should be rigid with steel stiffeners / pads and reinforcement. The infill material shall be resin bonded honeycomb core. All doors should be factory prepped for receiving appropriate hardware and provided with necesssary reinforcement for hinges, locks, and door closets.All doors and frames shall be finished with etched primer coating, stove zinc phosphate primer and thermosetting polyurethane aliphatic grade paint of approved colour. The door leaf and frame shall have passed minimum 250hours of salt spray test.
ELECTRICAL & INSTRUMENTATION Works
415V Power & Motor Control Centre (PMCC) -Supply, installation, testing, commissioning of:
415V PMCC#1
415V PMCC#2
Supply, installation, testing, commissioning of 415V Motor Control Centre (MCC) for ETP & STP
415V AC Distribution Board (ACDB) and Power Distribution Board (PDB)-Supply, installation, testing, commissioning of:
415V ACDB
220V AC Main Lighting Distribution Board (MLDB) and Lighting Panel (LP)-Supply, installation, testing, commissioning of:
220V MLDB
Feeder Pillar Box
Local Control Panel, Local Push Button Station, Local Junction Box -Supply, installation, testing, commissioning of:
Local push button station Type-A
415V LV Power Cables Supply, Laying & Terminations, gland, lugs and other accessories
1/C-630 Sq. mm (Al)
4/C-300 Sq. mm (Al)
4/C-240 Sq. mm (Al)
4/C-95 Sq. mm (Al)
4/C-50 Sq. mm (Al)
4/C -35 Sq. mm (Al)
4/C-16 Sq. mm (Al)
3/C-300 Sq. mm (Al)
3/C-35 Sq. mm (Al)
3/C-16 Sq. mm (Al)
3/C-2.5 Sq. mm (Cu)
3/C-2.5 Sq. mm (Cu) LIGHTING CABLE
1/C-2.5 Sq. mm (Cu) LIGHTING CABLE
Control Cables Supply, Laying & Terminations, gland, lugs and other accessories
5/C-2.5 Sq. mm (Cu)
Grounding & Lightning Protection System & Fitting & Accessories as required- Supply, installation, testing & commissioning
40MM dia MS Rod for main horizontal grid & riser
40MM dia & 3M long MS Rod for earth electrode (EE)
40MM dia & 3M long MS Rod for Lightning earth pit (LEP)
50x6 GS flat
35x6 GS flat
25x3 GS flat
16 SWG G.I. Wire
12 SWG G.I. Wire
8 SWG G.I. Wire
50x6 GS Earth Strip Horizontal & Vertical conductor and Test Link (lightning protection)
Pre-Fabricated Cable Trays and Other fitting & accessories (elbows, tees, crosses, reducers, Side Coupler Plate etc.) - Supply & installation
Ladder Type : Straight Run (R = 600)
Ladder Type : Straight Run (R = 300)
Perforated Type : Straight Run (R = 300)
Perforated Type : Straight Run (R = 150)
PVC Conduits Supply & installation
150mm dia
200mm dia
25mm dia PVC pipe
GI Conduits Supply & installation
For Rigid Steel : 20 mm (Lighting)
For Rigid Steel : 25 mm
For Rigid Steel : 50 mm
For Flexible Type : 20 mm (Lighting)
For Flexible Type : 25 mm
For Flexible Type : 50 mm
LIGHTING FIXTURE and Other fitting & accessories - Supply, installation, testing, commissioning : Indoor Lighting
BN308C LED40S-4000Â L120 SL WH (1x34W LED, Philips or Eqvt)
RC380B LED34S-6500 G3 PSU OD Diffused /6500 (1x32W LED, Philips or Eqvt)
DN393B LED12S-6500PSU WH (1x12W LED, Philips or Eqvt)
ROCHAK CIRRUS MINI TYPE (1x12W LED, Philips or Eqvt )
BY150P P LED75S CW PSU HE SY120 FG SPD ((1x75W LED, Philips or Eqvt)
LIGHTING FIXTURE and Other fitting & accessories - Supply, installation, testing, commissioning :Outdoor Lighting
30M High mast
200W flood light LED fixture with other accessories
RECEPTACLE - Supply, installation, testing, commissioning
5 Amp, 240 V (p-p), 2-Pole, 3-Pin type socket with 5A modular type switch (RA type)
15 Amp, 240 V (p-p), 2-Pole, 3-Pin industrial type, heavy duty, weather proof, dust proof, socket with 16A modular type switch (RB type)
3 nos. 5 Amp, 240 V (p-p), 2-Pole, 3-Pin, socket with 1 nos. 16A modular type switch for computer application (CS type)
63 Amp, 415 V, 3-Ph., 4-Pin industrial type, heavy duty, weather proof, dust proof interlocked plug and switch with earthing contact receptacle (RC type)
SWITCHBOARDS & JUNCTION BOXES - Supply, installation, testing, commissioning
1 no. 6A switch (SA)
3 nos. 6A switches with 1 no. 6A receptacle (SB)
Junction Box with connector for lighting (JB)
GENERAL SAFETY & MAINTENANCE EQUIPMENTS Supply. Erection as required
Sand buckets-5nos with stands
Portable Emergency light set complete with one 20W tube light, battery, battery charger and all other accessories
Insulating Elastomeric, Rubber mates as per IS15652:2006 1 Mt wide 2mm thick good quality, ISI marked and approved
415V Danger notice plate / caution board as per IS:2551.
First aid box with necessary items.
Rubber hand glove (pair) of 1.1KV grade as per IS:4770.
Fire extinguishers DCP type in 10kg / 9 kg capacity complete with handle , fixing bracket etc.
Shock treatment chart-English, Odia, Hindi
Artificial Respiration
1kV Digital Megger (Fluke/Hioki/Megger)
Multimeter True RMS (Fluke/Hioki/Megger)
Clamp Meter (0-200A) (Fluke/Hioki/Megger)
Arc flash suit of 31cal/sq.cm XL size
AIR CONDITIONING SYSTEM
Air Cooled Ductable Split Air Conditioner Each Split Air Conditioner (duct able air cooled unit) comprises hermetically sealed scroll compressor/s suitable for R-407C refrigerant, air cooled condenser/s in a powder coated sheet metal casing as an Outdoor Unit and dry panel type HDPE filters, cooling coil, evaporator fan, built-in controls & electrical including Microprocessor based Control panel, drip tray all encased in a powder coated casing as an Indoor Unit, damper & flexible connection at the evaporator fan outlet and interconnecting refrigerant piping (duly insulated) between the Outdoor and Indoor units. The conditioned air from SAC units is distributed in the desired areas through a network of galvanized sheet steel ducting and supply air diffusers/grilles. . The blower of the SAC unit shall be capable of developing sufficient pressure to overcome all resistances so that the dehumidified air will reach the farthest point of the floor to be air-conditioned. In case of fire, all the SAC units in the respective room will be turned off, getting the sense from the fire protection system.
Air Cooled Ductable Split Air Conditioner of 22 TR capacity
Air Cooled Ductable Split Air Conditioner of 17 TR capacity
Air Cooled Ductable Split Air Conditioner of 11 TR capacity
Air Cooled Ductable Split Air Conditioner of 8.5 TR capacity
Tower AC : Floor-mounted Tower AC unit with Rotary / Scroll Compressor. Capacity of each unit – 4 TR
Air cooled Non Ductable type Split Air Conditioner Each Air Cooled Non Duct-able inverter type Split Air Conditioner of 5 star rating shall be complete with hermetically sealed rotary compressor (for R-32/R-410a/ any non CFC/non HCFC refrigerant) and air cooled condensers in the Outdoor unit with powder coated GI casing, built-in electrical items & supports and Indoor unit housing dry panel type HDPE filters, cooling coils with drip tray, evaporator fans with two speed drive motors, control console, all encased in powder coated GI casings with swivelling type supply air grilles and decorative RA grilles and interconnecting refrigerant piping (duly insulated) between outdoor and indoor units and insulated drain piping, microprocessor based cordless remote control panel and plug top with connecting cable for each split unit Power supply to all the Hi-wall / cassette type AC units will be from nearest MCB or ACDB. Necessary Power & Control cabling, Grounding etc shall be provided. Air Cooled Non Duct-able Hi-wall / cassette type Air Conditioners will be operated and controlled from their individual hand operated Remote Control Panels.
Air cooled Non Ductable type Split Air Conditioner of 2 TR capacity
Air cooled Non Ductable type Split Air Conditioner of 1.5 TR capacity
Refrigerant Piping Refrigerant piping shall consist of hot gas piping, cold gas piping and liquid refrigerant pipeline all made of copper complete with at least 26mm thick Aluminium foil faced (factory laminated) Nitrile Rubber/ XLPE insulation interconnecting indoor and outdoor units, liquid line valves, liquid refrigerant piping, gauges and instruments, filter-drier, moisture indicator, isolating valves, complete with supports, clamps, etc., as may be required for safe and trouble free operation.
Drain piping 20 NB (Equipment drain piping of medium class GI complete with valves, fittings, hangers / supports etc. up to the nearest drain point (provided by the purchaser). Drain piping from the indoor units shall be insulated with 13mm thick Aluminium foil faced (factory laminated) Nitrile rubber / XLPE)
Ducting with Insulation GI sheet metal for Ducting shall be be as per IS 277 (with 275 Gms. / Sq. M Zinc coating) and shall be complete with necessary hangers, supports & supporting structures, proper sealing arrangement at the duct joints, vanes, dampers with control arrangement at each branch take-off and wherever necessary, flexible connections of rubberized canvas, etc.Splitter dampers shall be provided at all branches of the ducts. The construction of ducts shall conform to IS: 655 / SMACNA as far as applicable The quantities of ducting of different gauges to be included in the scope are as follows :
External thermal insulation on the both SA ducts and return air ducts (if applicable) with 19mm thick Fire Retardant, Closed Cell aluminium foil faced (factory laminated) Elastomeric Nitrile Rubber/ XLPE thermal insulation of entire duct.
Acoustic insulation of 25 mm thick Fire Retardant, Open cell, Erosion resistant Nitrile Rubber of density min. 140 Kg/cuM provided in the ducting up to a length of 6 M from the outlet of ductable split AD units.
Supply air diffusers with volume control dampers made out of extruded aluminium (powder coated) complete with fixing framework.
Volume Control Damper at the outlet of plenum Damper blades shall be made up of 16 gauge M.S.
VENTILATION
Supply fan filter unit Each Supply Fan-Filter unit shall consist of wall/Floor mounted inline Centirfugal fan, drive motor, Inlet Louver, HDPE filters, supply cowl with protective wire netting inside the room, supports and supporting structures, nuts and bolts, vibration isolators, back draft dampers etc.
Supply fan filter unit of Capacity 1000 cmh and static pressure of 20 mmWG
Supply fan filter unit of Capacity 1500 cmh and static pressure of 20 mmWG
Supply fan filter unit of Capacity 2000 cmh and static pressure of 20 mmWG
Supply fan filter unit of Capacity 2500 cmh and static pressure of 20 mmWG
Supply Fan unit Each Supply Fan unit(without filter) shall consist of wall mounted axial flow fan, drive motor, Inlet Louver, supply cowl with protective wire netting inside the room, supports and supporting structures, nuts and bolts, vibration isolators, ducting ( if required) etc.
Supply fan unit of Capacity 3500 cmh and static pressure of 12 mmWG
Exhaust fan
Exhaust fan of Capacity 1000 cmh and static pressure of 5 mmWG Each Wall mounted propeller type exhaust fan shall consist of axial flow fan, drive motor, back draft damper, supports and supporting structures, nuts and bolts, vibration isolators etc. Air entry will be through inlet louvers/door grilles.
Exhaust fan of Capacity 2000 cmh and static pressure of 15 mmWG Each Wall mounted exhaust fan shall consist of Bifurcated type axial flow fan, drive motor (flame proof type), rain protection cowl with bird screen,Non Return dampers at fan outlet, supports and supporting structures, nuts and bolts, vibration isolators etc. Air entry will be through inlet louvers/door grilles.
Exhaust Air System for Kitchen in Canteen Building Exhaust ventilation by mean of Exhaust Hood with Grease filter for cooking area and Exhaust Fans (Centrifugal type) And air entry through inlet louvers/door grilles. Suitable draining arragement should be provided in the kitchen hood. Exhaust fan of Capacity 15000 cmh and static pressure of 60 mmWG
Supply & Erection : Centre lathe Swing 500 mm x admit 3,000 mm For detail please refer tender specification.
Supply & Erection : Milling Machine Table 300mmX1100mm For detail please refer tender specification.
Supply & Erection : Shaping Machine Stroke 630mm For detail please refer tender specification.
Supply & Erection : Slotting Machine Stroke 450mm For detail please refer tender specification.
Supply & Erection : Radial Drill 50mm dia, arm 1000mm For detail please refer tender specification.
Supply & Erection : Column drill Drilling capacity in steel 38 mm For detail please refer tender specification.
Supply & Erection : Power saw Job dia 180 mm For detail please refer tender specification.
Supply & Erection : Pedestal grinder Wheel dia 300 mm For detail please refer tender specification.
Tool & cutter grinder swing 200mmX admit 1275mm (Supply & Erection) For detail please refer tender specification.
Supply & Erection : Vertical hydraulic press Capacity - 25 ton For detail please refer tender specification.
Supply of Portable diesel welding set -450 amps For detail please refer tender specification.
Supply of Hand lever shear Capacity 7 mm sheet For detail please refer tender specification.
Supply & Erection : Work Bench For detail please refer tender specification.
Supply & Erection : Pneumatic hammer, 150 kg For detail please refer tender specification.
Supply & Erection : Forge hearth, 800 mm dia For detail please refer tender specification.
Supply & Erection : Pipe bending machine, 75 mm dia For detail please refer tender specification.
Supply of Welding table For detail please refer tender specification.
Supply of AC Arc welding set/Electric Welding set - 450 amps For detail please refer tender specification.
Supply of Gas cutting and welding set For detail please refer tender specification.
Supply of Anvil, bench vice, pipe vice For detail please refer tender specification.
Supply of Torque wrench and other necessary tools For detail please refer tender specification.
Supply of Portable electric blower with hot air attachment For detail please refer tender specification.
Supply & Erection of Coil winding machine For detail please refer tender specification.
Supply & Erection of Drying cabinet For detail please refer tender specification.
Supply & Erection of Motor test panel and stand For detail please refer tender specification.
Testing equipment and instruments Multi meters, Voltage Detectors, Clamp-ons, Meg ohm meters/Insulation Tester, Micro ohm meters/DLROs, Ground Resistance Testers, Battery Testers, Solar Meters and PV Testers, Cable Tracers and Locators, Gauss meters, High Voltage, Hipot Testers, Motor Testing, Megger, Continuity and Current Tester 600V/ 100A with Open Jaw, Continuity and Current Tester 1000V/ 200A with Open Jaw, Receptacle Tester with GFCI Check, 3- wire, 110-125VAC, Battery Impedance Tester (Supply) For detail please refer tender specification.
Air compressor - 12 bar, 7.5 HP. To be supplied with all standard accessories. (Supply & Erection) For detail please refer tender specification.
Tyre Changer max wheel dia 1000mm (Supply & Erection) For detail please refer tender specification.
Inflator gauge (Supply) For detail please refer tender specification.
High pressure washing unit (Supply & Erection) For detail please refer tender specification.
Washing platform (for HEMM) with Automatic Underbody Car Washing System (Supply & Erection) For detail please refer tender specification.
Washing platform (for HEMM) with Hydraulic Jack (Supply & Erection) For detail please refer tender specification.
Hydraulic jacks, 10 to 25 tons (Supply & Erection) For detail please refer tender specification.
Lift hoist, 5 ton (Supply & Erection) For detail please refer tender specification.
Hydraulic trolley jacks, 5 ton (Supply & Erection) For detail please refer tender specification.
Portable garage crane, 2 ton
Hand trolley, 1 ton (Supply) For detail please refer tender specification.
Head light centering device (Supply & Erection) For detail please refer tender specification.
Battery charging unit, 48 V (Supply) For detail please refer tender specification.
Air compressor, 500 cfm at 9.5 kg pressure (Supply & Erection) For detail please refer tender specification.
Mobile repair van (Supply) For detail please refer tender specification.
Mobile crane, 30 ton (Supply) For detail please refer tender specification.
Mobile crane, 14 ton (Supply) For detail please refer tender specification.
Hand tools set and racks (Supply) For detail please refer tender specification.
Portable drill and grinder- Electric and pneumatic (Supply) For detail please refer tender specification.
Hand drill (Supply) For detail please refer tender specification.
Air blower (Supply) For detail please refer tender specification.
Bearing puller (Supply) For detail please refer tender specification.
Volume pump, Grease gun (Supply) For detail please refer tender specification.
Spray gun (Supply) For detail please refer tender specification.
Measuring instruments and gauges (Supply) For detail please refer tender specification.
Chain Pulley Block, Layout block (Supply & Erection) For detail please refer tender specification.
Carpenter’s bench vice (Supply & Erection) For detail please refer tender specification.
Double Girder EOT Crane -30/5 Ton (Supply & Erection) For detail please refer tender specification.
LMV BUILDING
Supply & Erection of Surface grinder For detail please refer tender specification.
Supply & Erection of Work Bench For detail please refer tender specification.
Supply & Erection of Air compressor 12 bar, 7.5 hp For detail please refer tender specification.
Supply & Erection of Hydraulic jacks, 10 to 25 tons For detail please refer tender specification.
Supply of Portable wash spray- Bus/Bolero For detail please refer tender specification.
Supply & Erection of Welding table For detail please refer tender specification.
Supply of AC Arc welding set/Electric Welding set For detail please refer tender specification.
Supply of Gas cutting and welding set For detail please refer tender specification.
Supply of Anvil, bench vice, pipe vice For detail please refer tender specification.
Supply of Torque wrench and other necessary tools For detail please refer tender specification.
Supply of Inflator gauge For detail please refer tender specification.
Supply, Erection, testing, Commissioning of STP. For detail please refer tender specification.
Supply, Erection, testing, Commissioning of ETP of capacity For detail please refer tender specification.
Bidder Name
Amount in Words
BSR INFRATECH INDIA LTD
SRC Infra Developers Private Limited
SRC Infra Developers Private Limited
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid