SPECIAL REPAIRS TO BUILDING NO ML 167 AT MALCOME LINE CONSTRUCTION OF TOILET AT PW TRG AREA PROVISION OF SHED IN MALCOME LINE AND BSO YARD AT INF SCHOOL UNDER GE MIS MHOW

Amount

B/R PORTION:

Demolition of cement concrete (unreinforced) of any description in ground floors and paving n. exc. 15cm thickness (below or above ground level) complete.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided forcomplete.

Demolition of cement concrete (reinforced) of any description in ground floors and paving n exc. 15cm thickness (below or above ground level) complete.

Demolition of brick work / stone boulders masonry built in cement mortar incuding all quoins , archeas, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises complete all as specified.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete

Taking down chowkats or frames not exc. 1.5 sqm each with shutters (without taking off shutters from the frames)

Taking down chowkats or frames exc. 1.5 sq.m but n.exc 4 sqm each with shutters (without taking off shutters from the frames)

Taking down door shutter from frame exc 1 Sqm but not exc 2 Sqm each and refixing the shutter in the same opening after easing and adjusting.

Taking down shutters of any description exc 1 Sqm but n.exc 2 Sqm each .

M&L for rendering 10mm thick in CM (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in CM (1:4) mixied with WPC on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified. Note: WPC shall be measured and paid separately.

M&L for rendering 5mm thick on concrete surfaces in cement mortar 1:3 finished on even and smooth without using extra cement as in ceiling, chajja etc.complete all as specified.

Supply only Liquid Water proofing compound PIDIPROOF LW+ of Dr FIXIT or other equivalent as approved by GE

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer all as specified

M&L for Preparation of old surfaces of wall by scrapping (any No of layers), washing,rubbing down and stopping of distempered and applying two coats of oil bound distemper all as directed and specified.

M&L for preparation of new surface of wall and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge

M&L for preparation of old decorated surfaces of wall by brooming down or steel wire brushing, scrapping down, moulds, moss and trading oil and greasy spots from plastered or unplastered surfaces including cornices, pilasters etc and applying two coats of white wash complete.

M&L for preparation of newly plastered surfaces of ceiling,chajja and applying three coats of white wash all as specified.

M&L for prepararion of old decorated surfaces of ceiling by brooming down, scrapping down smoke soot, moulds, moss and trading oil and greasy spots from plastered and unplastered surfaces and applying two coats of white wash complete.

M&L for preparation of new decorated surfaces of wall and applying two coats of Anti fungal weather coat acrylic emulsion paint Apex ultima of Asian paints or weather coat emulsion of Berger over a coat of exterior grade wall primer of asian paint or berger and one coat of 1mm to 1.5mm thick white cement based putty complete all as specified and directed Note :- Each stage (ie) preparation of surfaces,application of primer,application of first coat.and application of second coat shall be approved and passed by Engineer-in-Charge

M&L for complete removal of old decorated plastered surfaces of wall,pillasters, cornices etc by brooming down or steel wire brushing scrapping down and washing with water after completion and precoat treatment by applying two coats of Anti fungal weather coat acrylic emulsion paint Apex ultima of Asian paints or weather coat emulsion of Berger over a coat of exterior grade wall primer of asian paint or berger and one coat of 1mm to 1.5mm thick white cement based putty complete all as specified and directed Note :- Each stage (ie) preparation of surfaces,application of primer,application of first coat.and application of second coat shall be approved and passed by Engineer-in-Charge

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete.

S&F Coloured joint free non skid ceramic tiles of 7 mm to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile ,over and including 15mm thick screed in CM(1:6)

M&L for Coloured joint free Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including15mm thick screed in CM(1:6) complete all as specified and as directed.

M&L for coloured joint free Non Skid ceramic tiles 7mm to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in skirting/dado etc. set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 10mm thick cement mortar in CM 1:4 complete all as specified and as directed.

M&L for glazed ceramic coloured wall tiles (textured and design as required) in vertical surface as in skirting/dadoof size 450mmX300mmX7mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile ,over and including 10 mm thick rendering in CM 1:4 complete all as specified and as directed.

Dismantling of old stone slab ,tiles of any description and thickness laid, bedded and pointed in any mortar in floors,aprons etc.

M&L for Granite (of any type) 18mm to 20mm thick (work table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm screed bed in CM 1:6.

M&L for machin cut kota stone slab 20mm to 25mm thick as in flooring mirror polished over and including15mm cement screed base laid in CM 1:6 , and jointed in neat cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete.

M&L for Kota stone slab 18mm to 20mm thick in riser of steps, skirting, dado and pillar, window cill laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete over and including 10mm thick rendering in CM 1:4..

M&L for chequered cement concrete tiles (glossy finish) 40 cm x 40 cm x 30 mm thick set ,jointed and pointed in neat cement slurry in floors with grey cement and pigment laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and as directed.

S&F Cement concrete tiles of size 25cm x 25cm x22mm thick, with grey cement & no pigment machine pressed; set, jointed & pointed in neat cement slurry in floors, & cut & polished over and including15mm thick screed in CM(1:6)

M&L for Rounding to edges of stone slabs one edge such as steps cooking platform and other similar situations complete all as specified and as directed.

S&F Plain, solid, straight 2nd class hard wood frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints.

S&F PVC door frames of size 50mm x 47 mm made out of 5 mm single side prelam PVC sheet used instead of plain colour PVC sheet reinforced with MS Square tube in opening of suitable size complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded prelam PVC `C' channel having a prelam PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of prelam PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable prelam PVC sheet beading, & joined together with solvent cement, in the frame at site as per specification & drawing.

S&F Pressed steel frame of size 125mmx60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified

M&L Providing, cement concrete type C-1 1:3:6 (12.5mm graded stone aggregate for filling of Pressed steel frame etc, rounded or chamfered on edges complete as specified, supplied and fixed

S&F 30 mm thick Flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides

M&L for Cutting holes in brick/block walls built in cement mortar exc half brick n.exc one brick for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required complete as specified.

S&F mild steel bands, straps, support or stays for rainwater ventilating pipes including bolts if required, hook and eye, Hold fasts wall ties hooks for hanging fans, plain angle etc all as specified and directed.

S&F second class hard wood glazed skeletn shutter, 35mm thick, divided into squres plain chamfered open rebated and prepared to received glass guaze etc, edges of framing plain chamered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shuters as specified .

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel over coat of pink primer.

M&L for preparation of old painted wooden surface of any description, over 10 cm in width or girth and applying one coat of synthetic enamel paint

Providing and fixing of double rebate openable/fixed windows made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 microns, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 72 x 55 mm, centre mullion section 72 x 50 mm, shutter section 47 x 20 mm,fly mesh section 40 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter, fly mesh and 20 mm provision for guard bars/grills, the sections cut to length mitre joined with corner bracket, centre mullions fixed with mullion cap, stay, handles, latch, 2 Nos of heavy duty stainless steel pivot hinges per shutter and panelled with 5mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self-expanding screws, including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. complete as per the direction of Engineer in Chargeconforms to IS -513:2008.

Providing and fixing fixed louvers fabricated from Roll formed sections made of galvanized Steel colour coated/powder coated (base Steel as per IS 513 ‘D’ quality, galvanized as per IS 277 with zinc of 120 grams/Sqm) with thickness of 0.58mm coated sections to be primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick, section for external frame 33 x 58 mm, glass holding flanges made of polypropylene, sections are to be cut to length, mitre joined with corner bracket. The above frames should be fixed to the concrete/masonry walls by means of self expanding screws conforms to IS -513:2008..

M&L for preparation of new steel surfaces of any description over 10cm in girth or width and applying two coats of synthetic enamel paint over a coat of primer complete all as specified

M&L for preparation of old steel surfaces of any description, not otherwise described, over 10 cm in width or girth and applying one coat of synthetic enamel paint.

S&F stainless steel wire mesh of size 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

S&F 100mm long butt hinges medium weight cold rolled mild steel complete all as specified

S&F stainless steel butt hinges 100 mm long all as specified

S&F 150 mm long Aluminium anodizes barrel tower bolts of extruded section complete all as specified.

S&F 150 mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixedcomplete all as specified.

S&F 150 mm size aluminium anodized handle complete all as specified

S&F 150 mm size Mild steel pressed handles, oval type, stove enamelled black complete all as specified

S&F in repairs aluminium floor door stoppers double legged length 140mm with hard drawn steel spring fitted in floor complete all as specified and directed.

S&F 300 mm long aluminium alloy anodized sliding door bolts with Hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified

S&F 300 mm long Mild steel sliding door bolts,plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified

S&F in repairs 300 mm long aluminium alloy anodized sliding door bolts with Hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified

S&F mild steel 300mm ordinary rat tail rod springs including roller and roller plate complete

M&L for rendering 5mm thick ,on concrete surfaces in cement mortar 1:3 mixed with and including WPC @200ml/bag of cement, finished even and smooth without using extra cement as in repair of RCC Chajja,beam column,etc complete all as specified & directed.Note: Rendering shall be carried out in building of height between 3 m to 7m and quoted shall be inclusive for necessary scaffolding,safety equipments as required .

M&L for preparation of surface of any description and applying bituminous primer (conforming to IS-3384-1965) @ 0.30 Kg/Sqm complete.

M&L for applying a tack coat of industrial bitumen grade of 85/25 at the rate of 1.2 Kg per Sqm including cleaning surfaces complete all as specified .NOTE: (1st coat for bonding material below membrane and 2nd coat on top of membrane. Each coat shall be measured and paid separately under this item .)

M&L 3mm thick APP based polymeric membrane minimum weighing 3kg/sqm and reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed.Note: Application of APP membrane shall be carried out through authorised applicator of Manufacturer.

M&L for applying two coats of bitumen based aluminium painting on water proofing treatment including preparation of surface as in non acessable area complete all as specified and directed.

S&F in repair vitreous china squatting Pan “Orissa” Pattern, of size 580mm x 440mm white colour with integral foot rests (excluding flushing cistern and flush pipe) including provision of cement concrete bedding complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white colour (excluding fixing bolts, flushing cistern & flush pipe) including plastic water closet seat, white colour, closed pattern with flat bottom, & cover & mild steel CP or aluminised hinging device.

Supply and fix in repairs wash hand basins, white colour,vitreous china,of size 550x400mm (flat back, or angle back type) including cutting for and pinning in ends of brackets or erecting stand inclusive of waste pipe,waste coupling etc complete all as specified and directed.

S&F in repair CP bottle trap 32mm bore for wash basin with inlet and outlet screwed for connection including necessary packing union and cup and fixed.

S&F in repair 32 mm bore low density polythene pipe (LDPE) of pressure rating 6 kgf / Sqcm for WHB and sink complete all as specified and directed.

S&F in repair 15mm bore pillar taps, cast copper alloy with capstan heads, chromium plated,fancy type screwed down high pressure with or without lettered “HOT” or “COLD” with long screwed shanks and fly nutscomplete all as specified and directed.

S&F in repair CP brass fancy type 15mm bore bib taps, screwed down , and screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair CP fancy type stop valves ,cast copper alloy concealed type , screwed both ends for iron pipe or for union of 15mm bore complete all as specified and directed.

S&F for stop cock cast copper alloy with crutch or butterfly handle fancy type screwed for iron pipes or for brass ferrule for 15mm all as specified.

S&F in repair 20mm bore dia stop valve cast copper alloy screwed down , high pressure with crutch or butter fly handle ,screwed both ends for pipe or for unions and fixed complete all as specified and directed.

S&F 10 litres capacity PVC flushing cistern, low or high level, with inlet, ball valve, syphonic action type, float and handle, PVC Flush pipe , pull or push type including brackets complete as fixed in repairs.

S&F in repair sink mixer with swinging/rotatable spout with connecting legs & wall flanges Make : Plumber or other equivalent as approved by GE complete all as specified and directed

S&F in repairs Wall mixture chromium plated continental non telephonic wall mixer shower hot & cold, 15mm bore, bright finish with three joints screwed the ends for iron pipe and plugging complete all as specified and directed.Make Plumber or other equivalent as approved by GE .

S&F in repairs Angle Stop valves one way, brass chromium plated, fancy type, fixed to iron pipe or for unions 15mm bore complete.Make Plumber or other equivalent as approved by GE .

S&F in repair fancy type chromium plated two way bib cock of 15mm bore two way bib cock screwed for iron pipe or brass ferrule etc complete all as specified and as directed.Make :Plumber or other equivalent as approved by GE .

S&F in repairs Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed 20mm dia

S&F health faucet with flexible pipe of one metre length including stand complete all as specified and as directed . Make : Plumber or other equivalent as approved by GE .

S&F in repairs CP Brass Fancy type shower rose 125mm dia with shower arm 30mm long of approved quality complete all as specified and directed.

S&F in repair Stainless steel toilet paper holder fixed to wall with brass screws complete all as specified and as directed.

S&F in repairs mild steel chromium plated soap dish (oval) type of size not less than 50mm dia complete.

S&F in repairs brass chromium plated corner glass 5mm thick shelf with bracket complete all as specified and directed.

S&F in repairs shelf glass assembly consisting of 5.5mm thick sheet glass,shelf 120mm wide with CP bracket guard and railing 600mm long.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450mm/600mm

S&F in repair stainless steel sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F stainless steel plate rack for kitchen 1mm thick of best quality with suitable hanging arrangement and fixed to wall complete all as specified and directed by Engr-in-Charge.Note : size of plate rack shall not be less than 900x 1200mm and weight of rack shall not be less than 8.50 kg each.

S&F in repair Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed.

S&F in repairs of brass CP tubular towel rail 20 mm dia 60cm long between flange with brackets complete all as specified and directed.

S&F in repairs 25 mm dia stainless steel curtain rod including decorative brackets, at ends with necessary fixing arrangements complete all as specified and directed.

Taking down steel tubing 15mm bore and connections complete all as specified and directed by Engineer - in – Charge.

S&F GI tubing 15mm bore medium grade with all fittings & fixed complete to walls /ceiling or laid in floors all complete all as specified and directed.

Refixing old steel tubing and connections in new or old position walls,ceiling,floors etc.15mm dia all as specified.Note:Serviceable pipe obtained from taking down shall be fixed .

Taking down steel tubing 20mm bore and connection complete all as specified and directed by Engineer - in - Charge.

S&F GI tubing 20 mm Bore medium grade with all fittings & fixed complete to walls /ceiling or laid in floors all complete all as specified and directed.

Refixing old steel tubing and connections in new or old position walls,ceiling,floors etc.20m dia all as specified.Note:Serviceable pipe obtained from taking down shall be fixed .

M&L for cutting chases, pinning in, making good to facings where required and pointing in CM(1:3) to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in Stone/ brick walls all as specified .

Dismantling water tanks and removing to store of capacity exc 250 & n exc 500 litre complete all as specified & directed.

S&F Rotational moulded polyethylene water storage tanks ,double layered of capacity of 500 liters (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, complete all as specified & directed.

S&F 20 mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified & directed.

S&F in repairs 20 mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified & directed.

Disconnecting existing tank of 500 litres capacity ,setting aside(or lowering if required) for repairs,cleaning etc and hoisting if required reconnecting and refixing in position including cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc.complete

S&F in repairs PVC (SWR) pipes 160mm bore single socketed in any length with rubber ring joints fixed to walls/floors complete all as specified

S&F in repairs PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints fixed to walls.

Fixing only PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints fixed to walls.Note:Old serviceable pipe shall be fixed .

S&F in repairs PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints fixed to walls.

Fixing only PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints fixed to walls.Note:Old serviceable pipe shall be fixed .

S&F PVC (SWR) bends any radius 160mm dia

S&F PVC (SWR) bends any radius 110mm dia

S&F PVC (SWR) bends any radius 75mm dia

S&F PVC junction single (single T) 110mm dia equal or unequal with access door.

S&F PVC junction single (single T) 75mm dia equal or unequal with access door.

S&F 100mm stack clamps made out of 50 mm x 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof

S&F 75mm stack clamps made out of 50 mm x 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof

S&F in repair PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement

S&F in repair PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement

M&L for 75 mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection including making joint at every 3 mtr interval and at corner and filled with mixture of bitumen and sand and finished even and smooth with extra cement and laid in alternate bays complete all as specified and directed.

M&L cement concrete 1:4:8 type D2 using 40mm graded stone aggregate ,75mm thick as in subbase etc.all as specified .

M&L for cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in levelling course in floor,sunken portions etc complete all as specified and directed.

M&L for plain cement concrete 1:5:10 type E2 using 40mm graded aggregate as in filling of sunken portion complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:3 mixed with and including WPC ,finished even and smooth without using extra cement as in vertical sides and testing for water tightness by ponding of water for 72 hours all as directed by Engineer-in-Charge .

S&F 40mm dia GI Tubing as in spout pipe of medium grade including cutting in any length as required and fixed to wall & floor etc complete all as specified and directed.

Dismantling wall and ceiling boards (fibre,pulp,insulation,etc) or insulation boards/slabs/blankets/kitchen cupboards,any thickness, including cover fillets complete all as specified.

S&F 18/19mm thick prelaminated particle board, exterior grade,prelaminated one side with decorative choice lamination &other side balancing white lamination,fixed with screws to timber frame work all as specified.

S&F 100mm hasp and staple safety type of aluminium anodised including bolt to hinges plate and fixed with screws complete all as specified and as directed.

S&F continuous (Piano) hinges mild steel bright finish or electrogalvanised 40mm flaps width (when open)

S&F 18mm thick factory made 100% solid rigid PVC (Poly Vinyl Chloride) foam sheet Prelam colour having density of 600kg/cbm manufactured by an Iso 9001-2015 certified company.Termite proof,water proof and flame retardant PVC sheet,manufactured by single layer extrusion process for one side prelaminated solid PVC foam sheet. PVC film laminate should be pasted on PVC sheet with suitable adhesive and approved shade.

S&F 18mm thick factory made 100% solid rigid PVC (Poly Vinyl Chloride) foam sheet Plain colour having density of 600kg/cbm manufactured by an Iso 9001-2015 certified company.Termite proof,water proof and flame retardant PVC sheet,manufactured by single layer extrusion process.

S & F modular type stainless steel basket of size 0.50 m x 0.53 m x 0.10 m (dia of wire not less than 3.0mm) of any shape with side sliding roller clip and sliding rails on both side fixed with steel screws including all fixing arrangement complete as specified and dirceted.

All as per item no 133 above but basket of size 0.50 m x 0.53 m x 0.15 m complete as specified and dirceted.

All as per item no 133 above but basket of size 0.50 m x 0.53 m x 0.21 m complete as specified and dirceted.

S&F 100mm size MS mat/glossy finish handle complete as specified and directed.

S&F stainless steel self closing hinge of size 75mm for PVC door shutter complete as specified and directed.

S&F 50mmx15mm size magnet door catcher for closing for PVC door shutter complete as specified and directed.

S&F mild steel drawer cabinet channel for moving the drawer etc complete as specified and directed.

M&L for RCC 1:2:4 type B1 using 20 mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like complete.Note: Reinforcement shall be measured and paid separately under relevant item.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200m thick (Horizontal or sloping) ,fair finished surfaces of concrete flat .

M&L for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

S&F Rolled mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lenghts i.e. within 20mm of the length indicated) GDE Fe 410-0 W (Gde E-250) quality A

S&F mild steel framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings including steel sheeting or other covering, also fastening and fixing complete.

S&F mild steel framed work such as grills,gratings, etc. with ends of barsshouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

M&L for Cutting holes into or through brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type Bl as required superfacial area exc 150 sqcm but n.exc 400 sqcm

Dismantling Asbestos corrugated & Semicorrugated etc sheetin in roof covering of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as directed at site.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified.

M&L for cutting channels, grooves or rebates n exc 15cm girth, and trimming surface with or without reinforcement.

Excavating in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation etc. n exc 10 sq m on plan and getting out in soft/loose soil all as specified.

Removing excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n exc. 1.5 m above the starting point

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil all as specified.

M&L for Salt glazed stoneware drain pipe Grade 'A' 200 mm bore laid in trenches and jointed including taking down existing pipe complete all as specified and directed.

M&L Salt glazed stoneware drain pipe Grade 'A' 150 mm bore laid in trenches and jointed including taking down existing pipe complete all as specified and directed.

M&L Salt glazed stoneware drain pipe Grade 'A' 100 mm bore laid in trenches and jointed including taking down existing pipe complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in bed concrete to drain pipes of 200 mm bore including packing under and haunching against the sides of pipes after they are laid and tested including taking down existing concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in bed concrete to drain pipes of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested including taking down existing concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in bed concrete to drain pipes of 100 mm bore including packing under and haunching against the sides of pipes after they are laid and tested including taking down existing concrete complete all as specified and directed.

M&L for Brick work with sub class 'B' bricks / fly ash modular bricks , straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specifed and directed .

S&F in repairs coloured powder coated aluminium strip of size not less than 0.90 m long and 30 mm wide with brush lining fixed at bottom of wooden/aluminium door to cover gap between door and floor complete all as specified and directed.

Surface excavation n.exc 30cm deep and avaraging 15cm deep and getting out in soft/loose.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m in depth: for foundation, etc or for shafts,wells cesspits, manholes, pier holes, etc getting out in hard/dence soil all as specified and directed

M&L for hardcore with broken stone or boulder of gauge n. exc 63mm, deposited spread and levelled in layers n exc 150mm thick, watered and rammed to true surface complete all as specified and directed.

M&L for cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in foundation ,filling ,sub base of floor,and mass concrete.

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate for foundations including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified.Note: Reinforcement shall be measured and paid separately under relevant item.

M&L for formwork rough finished surface of concrete to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts complete all as specified.Note: Reinforcement shall be measured and paid separately under relevant item.

M&L for Formwork rough finished surfaces of concrete to sides of concrete flat or curves sides of pillers,posts, struts,piers,columns and stanchions complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type BI using 20mm graded stone aggregate as in beams,Cantilevers.brussumenrs,lintels over 1.50 m span all as specified and directed.Note: Reinforcement shall be measured and paid separately under relevant item.

M&L for form work to sides and soffits of floor or roof beams haunching, lintel, coloumn, cantilevers shelves includig supported over hangs etc with rough finished flat surfaces of concrete.

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in slab supported on wall , landings, beams canopies, deck slabs and shelves etc.complete.Note: Reinforcement shall be measured and paid separately under relevant item.

M&L for use and waste of formwork to sides and soffits of slab such as rof slab,floorslab,landng and similer work,etc not exceeding 200mm thick with rough fnished surface of concrete flat complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in chajjas etc.complete .Note: Reinforcement shall be measured and paid separately under relevant item.

M&L for 6mm to 8mm dia mild steel TMT bars cut to length bent to shapes as required including bending cranking and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified.

All as per item No 175 above but 5 mm to 10 mm dia as in Stirrups,spaces & binders complete all as specified and as directed.

M&L for moorum/Red bajri filling in floor or paving laid in layers n.exc 15cm thick spread,levelled and rammed including watering complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C2 using 40mm graded stone aggregate ,75mm thick , as in sub base,foot path etc complete all as specified and directed

Removing excavated material (soil) to a distance exc 50 m but n exc 500 m and depositing where directed at a level n.exc 1.5m from starting point .

M&L for plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in floor and levelling course ,25mm thick all as specified and directed

S&F Powder coating anodised aluminium ventilator ( Louvers type) with louvers glass and glass stay,setion weighing 0.55Kg/m incl necessary joining cleats, glazing clips for fixing of wiremesh,rubber neoprene packing,anodised aluminium snap beading screws etc.(minimum thickness of powder coating 50micron) complete all as specified and directed.

S&F PVC grating 100mm dia fixed to floor trap

S&F PVC Pipes 110mm dia bore single socketed,in any length with rubber ring joints, laid in floors all as specified and directed

S&F 75mm dia PVC (SWR) floor trap , plain with grating including jointing with solvent cement

S&F 100mm x 100mm size Salt-glazed stoneware gully trap,square or round mouthed ,type 'P'

S&F PVC Pipes 75mm bore single socketed,in any length rubber ring joints,laid in floors

S&F GI tubing 25 mm Bore medium grade with all fittings & fixed complete to walls /ceiling or laid in floors all complete all as specified and directed.

S&F Rotational moulded polythene water storage tanks of 1000 litres capacity ,double layered, (cylindrical vertical with closed top) hoisted completed all as specified and directed

S&F PTMT nipple 25 mm suitable for HDPE water tank.(Minimum weight 65 gms ) complete all as specified and directed.

S&F 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass complete all as directed and specified.

S&F cast iron 'P' or 'S' trap for EWC

S&F Vitreous china urinal half stall white coloured with urinal spreader of CP for fixing with 15mm dia pipe,( Minimum weight 60 Gms)Complete including providing and fixing plugs,beeding urinal against wall in cement mortar 1;2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with spreader, flush pipe,grating and union for discharge pipe ( excluding of fxing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F vitreous china wash basin white (oval shaped under counter) of size 550mmX400mm compete all as specified and directed

S&F 15mm dia swan neck pillar taps fancy type,cast copper alloy,with capstain heads,chromium plated screwed down high pressure,with or without lettered 'HOT' or 'COLD" with long screwed shanks and fly-nuts screwed for iron as specified and directed.

S&F waste fitting 32mm bore,brass,chromium plated for basins etc with long screwed shanks and fly-nuts.flange and bed deal in red lead cement and complete all as specified and directed.

S&F PVC waste pipe for wash hand basin / urinals

M&L for rendering 10mm thick in cement mortar 1:3 as on concrete surfaces in ceiling finished even and smooth without using extra cement all as specified and directed.

M&L for preperation of new plastered surfaces of ceiling and applying three coat of white wash all as specified and directed.

M&L preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of wall care putty complete all as specified and directed.

M&L for 1mm thick white cement based wall care putty as required complete all as directed and specified.

M&L for machine pressed precast concrete interlocking paver block using rubberised moulding any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 Grade with grey cement and no pigment over and including 30mm thick dry screened sand complete all as specified and directed.

M&L for PCC (1:3;6) type C1 using 20mm graded stone aggrgate as in mud stops.kerbs etc rounded or chemfered edges all as specified and directed.

M&L for construction of sockage wells of 3.0m dia and 3.0 deep including earth work excavation in ordinary soil,foundation in PCC 1:3:6 ,walls of Honey combed and solid in M25 grade concrete,including intercepting chamber,screen chamber with brick work in CM 1:4 , RCC cover slab in M25 grade concrete ,RR masonary ,filling with brick bats, complete all as specified and shown in TD-DRG NO CEJZ/TD/sheet No 1/1 dated 05/05/2000

M&L for construction of septic tank for 100 users including excavation in ordinary soil,foundation in PCC 1:2:4,brick work in CM 1:4 Slab covers including RCC precast manholes cover having 6mm plate embedded all around/Fibre reinforced cover with angle iron frame Vent shaft and sludge chambers etc. complete all as specified and shown in TD-TRG NO CEJZ/TD/57 sheet No 1/4 to 4/4 dated 05/05/2000

M&L for concrete bed with cement concrete 1:4:8 type D2 using 40mm graded stone aggregate for 150mm bore drain pipes including packing under & haunching against the sides of pipes after thay are laid and tested in all as specified and directed.

M&L for Reinforced concrete pipes 150mm bore class NP2 laid and jointed complete with collar all as specified and directed.

M&L for rendering 15mm thick on unfair faces of brick work or concrete surface in cement mortar 1:6 , finshed even and smooth without using extra cement all as specified and directed.

S&F FRC manhole cover with rectangluer frame of size 44''X26'' md-10 all as specified and directed by Engineer -in-charge including taking out old manhole cover slab from site all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges,hips,valley gutters,drip and straight flashings fixed with self tapping screws all as specified.

M&L for plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in coping,kneelers,apex stones,bed plates,water trough and the like including weathering ,slightly rounded or chamfered angles and throating as directed

Excavation in post holes (or similar holes) each not exceeding 0.50 cum getting out in hard/dense soil including returning , filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm,watering and removing surplus soil to distance not exceeding 50m and making good the disturbed surface complete.

M&L for plain cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified

S&F Mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161- 1979 grade St.-240 complete all as specified . NOTE: Tubular truss shall be fabricated all as specified and directed by Engineer-in-Charge and fixed with necessary bolt,nuts etc

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified

E/M PORTION :

Taking down old copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Taking down ceiling fan/ exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M No II complete all as specified and as directed.

M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLS multi stranded conductor cable in and including Concealed PVC conduit of size 20/25mm ISI marked inclusive of tees ,bend ,elbows etc upto and including sunk in anodized pressed steel box of 1.6 mm thickness, 60 mm deep for housing switch socket etc with white laminated 3 mm thick hylam sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :-

One light point controlled by one, one way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

One light point controlled by one, two way switch 5 Amps

One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

One bell point controlled by one, bell switch 5 Amps

All as per item No 213 here in before but using 2.5 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S&F Switch Piano type single pole 5 amp, 230 Volts complete all as specified and directed at site.

S&F Switch Piano type 2 way switch 5 amp, 230 Volts complete all as specified and directed at site.

S&F switch bell push piano type 5 amp, 230 Volts Complete all as specified and directed at site.

S&F socket outlet 2 in 1 , 5 pin, 5 amp, 230 Volts complete all as specified and directed at site.

S&F Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

S&F stepped type electronic fan regulator flush type complete all as specified and directed at site.

S&F lamp holder , PVC / Polycarbonate type with back plate suitable for batten/ slanting fittings complete all as specified and directed.

S&F Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

S&F Modular type TV Socket outlet ISI Marked complete all as specified and as directed.

M&L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit shall be measured as one unit length.

S&F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S&F MCB Single pole and neutral rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S&F MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S&F metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps complete all as specified and as directed

S&F Water heater storage type, electric,capacity of 25 litres ,BEE 5 star rated complete all as specied and as directed.

S&F ceiling fan with electronic type regulator and accessories 230 Volts, 1200 mm sweep BEE 5 star rated compelte all as specified and directed.

Labour only for refixing the celing fan/ Exhaust fan including provision of 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal including over hauling ,painting of fan with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc. complete all as specified and as directed. Note :Ceiling/exhaust fan taking down from ser. item No 229 shall be fixed under this item.

S&F Highly efficient LED Bulbs, 10 W, used as a ready replacement for existing GLS/CFL direct fit lamp,in B-22 cap of make Bajaj, Havells, HPL complete all as specified and directed

S&F Decorative wall mounted luminaire made out of polycarbonate with unbreakable globe suitable for LED bulb and provosion of LED bulb 9 watts complete all as specified and as directed. Make Havells Cat No LHDLO6160099 or other equvalent make in Philips, Bajaj.

S&F LED 10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed. Make-Havells Cat Pt No. LHEXACP71N1W010, Bajaj Cat Part No BCLSB 10 NW or other equivallent model in Wipro, Philips.

S&F Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. Make :-Havells Cat Pt No. HEXAFT10WLED857SSYMBOPC, Bajaj Cat No BIBWP 10W LED or other equvalent make in Philips, Wipro.

S&F wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make :- Make Havells Cat Pt No LHEXBLP7PN1W020, Bajaj Cat part No BCLAB 20W WH LED P, Wipro Cat part No LL20-281-XXX065-ALI or other equvalent make in Philips, Havells.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 30 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Make :- Havells Cat Pt No.LHEXAYP7PN6K030, Bajaj Cat part No ENXT P 24L WH CR PC SD (Edge plus series) or its equvalent in Philips, Wipro.

S & F for energy efficient exhaust fan of 230 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted). Make : Havells Model Ventil Air DS or equivalent in Bajaj or Crompton.

S&F PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 20 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish including plastering complete all as specified and directed.

M&L for Point wiring with FR LS PVC insulated PVC unsheathed electric cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area drawn in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good and matching disturbed surface of wall with existing surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit surface casing caping will be used) & 1.5 sqmm green FR LS PVC insulated unsheathed copper conductor as earth wire connected to earth dolly by providing lugs including galvanised boxes and bakelite sheet for mounting switches, sockets, fan regulators etc for One light point/fan point controlled by one switch . Make of PVC conduit/Casing Caping:- Plaza/Finolex/Polycab/Kalinga/Jindal/Asian .

One light point controlled by one switch

One Exhaust fan point controlled by one switch

One 5amps socket out let point controlled by one switch on same board with other switches.

One 5amps socket out let point on independent board controlled by one switch.

All as per item no 240 here in before but using PVC insulated unsheathed 2.5 sqmm cross sectional area cable for phase /neutral & for earth 2.5 Sq mm green PVC insulated cable for 15 amps socket point on independent board controlled by one switch.

S&F switch piano flush button single pole one way 15 Amp 240 volt complete as directed.

S&F socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 230 volts complete as directed.

S&F integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 , Bajaj cat Pt No. BCLSB 18WH or other equivalent in Wipro

S&F integrated LED tube light fitting 1x9/10 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square box complete all as specified and directed .Make:- Havells Cat No. LHEXBLP7IN1W009 Bajaj Cat Pt No. BCLSB 10 WH or other equivalent in Wipro

S&F LED street light fittings 1x30 Watt, 5700K complete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible copper cable complete all as specified and directed .Make:- Havells Cat No.LHEXAYP7PN6K030 Crompton Cat No. LSTO-25-CDL, Bajaj Cat No. BCLST 25W LED IV2

S&F MCB SPN 6 to 32 amps 10 KA, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-in-Charge.

M&L for Sub main wiring with two runs of single core FR LS PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including FR LS PVC insulated unsheathed 4.0 Sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge.

S&F Exhaust fan 200mm sweep, AC single phase 230 Volts, non metallic type, complete with louver including electric connection with suitable size copper conductor cable, clamps, nuts, bolts etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall and matching with the existing surface of wall complete all as specified and directed by Engineer-in-Charge. Make : Havells Model: Ventil Air-DX white or other equivalent model in Bajaj/Crompton

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x 60cmx 6.3 mm thick buried directly in ground ( earth pit not less than 2.25 meter deep below ground level) with the top edge of the earth plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate No.5 of MES SSR parts-I and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of PCC earth chamber in mix 1:3:6 type c-1 with 40 mm thick RCC 1:2:4 type B-J cover reinforced with 8mm dia MS bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia GI light grade and 15mm dia light grade pipe for earth lead protection and testing on completion including taking down/dismantling the existing complete all as specified and directed.

Supply and laying LT cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 2 core 10 sq mm

Supply laying and jointing GI pipe 'light grade' 40 mm bore in trenches/under floors or roads/ along poles/ on wall including clamps for protection of cables complete all as specified and directed.

M&L for clean and dry sand (un-washed) in trenches including spreading and levelling for cushioning of UG cable complete all specified and directed.Note:Thickness shall be measured after punning

M & L for brick size sub class ‘B’ (modular size), laid flat in trenches for protection of cable complete all as specified and directed.

Chitragupta Construction

Sudarshan Associates

Goyal Construction

SHRI RAM CONSTRUCTION