PROVN OF TOILET BLOCK IN CR II AND CR III WITH SEWAGE SYSTEM IN PW DIV PROVN OF SOLAR SECURITY LIGHT FOR MES INSTALLATION PROVN OF LPG AND OXYGEN CYLINDER STORE ROOM AT MH AND PROVN OF CERTAIN MINOR REV WORKS UNDER GE MIS MHOW

Amount

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

Excavating in trenches, n exc 1.5m wide & n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, man-holes, pier holes, etc. n exc 10 sq m on plan & getting out in soft/loose soil.

M&L broken stone or boulder hardcore of gauge n.exc 63 mm deposited spread and leveled in layers n.exc 15 cm thick, watered and rolled/rammed to a true surface.

M&L for Plain Cement Concrete(1:4:8) Type D-2(using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed..

M&L for Plain Cement Concrete(1:3:6) Type C-2(using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed..

M&L for RCC (Nominal mix) (1:2:4) Type B-1 using 20mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass comlete all as specified and directed.

Formwork Rough finished surfaces of concrete to sides of concrete flat or Curved side of foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as directed.

M & L for RCC (Nominal mix) 1(:2:4) Type B-1 using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts comlete all as specified and directed.

Formwork Rough finished surfaces of concrete to sides of concrete flat or Curved sides of pillars, posts, struts, piers, columns and stanchions complete all as directed.

M & L for RCC (Nominal mix) (1:2:4) Type B-1(using 20mm graded stone aggregate) as in Beams, cantilevers, bressumers, lintels over 1.5span . Complete all as specified and directed.

Form work to sides and soffits of floor or roof beams, cantilevers, shelves, lintels for rough finished surfaces of concrete.

M & L for RCC (Nominal mix) (1:2:4) Type B-1(using 20mm graded stone aggregate) as in Slabs supported on walls,beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like Complete all as specified and directed

Formwork to soffits of flat suspended slabs such as roof slabs, floor slabs, landings and similar work; not exc 200mm thick (Horizontal or sloping) Complete all as specified and directed

M & L for use and waste of Timber Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L for TMT bars 6 mm to 8 mm dia cut to length, bent to shape reqd incl cranking, bending and binding with MS wire n.exc 0.90 mm dia (annealed) for stirrups. Complete all as specified and directed

M&L for MS TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips. Complete all as specified and directed

M&L for Brickwork with fly ash brick with using Modular size Brick , straight or curved on plan exc 6m mean radius built in CM (1:6) complete as directed and specified.

M&L for Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM (1:4) complete as directed and specified

M&L for moorum/red bajri filling in floor or paving laid in layers n.exc 15 cm thick spread, levelled and rammed including watering complete all as specified and directed.

M&L sand filling under floor including waterring and consolidaion complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering & well ramming in layers not exc 25 cm in soft/loose soil. Complete all as specified and directed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point. Complete all as specified and directed

M&L for 75 mm thick plain cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub base. Complete all as specified and directed

M&L for 40mm thick plain Cement concrete (1:2:4) type B-1, using 20 mm graded stone aggregate Complete all as specified and directed

M&L for hardcore of gauge n exc. 63 mm,of broken stone deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for coloured Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 20mm thick scread bed in CM (1:6) Complete all as specified and directed

M&L for Machine pressed precast conctete interlocking paver block using rubberised moulding any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and no pigment over 25 mm thick dry screened sand complete. Note: Sand cushing shall be measured and paid seperately)

M&L for sand dust as in levelling course of interlocking and chequred tiles complete all as specified and as directed.

M&L for PCC (1:3:6) type C-1 using 20mm graded sotne aggregate as in kerbs etc rounded or chamfered edges and bed block of hold fast Complete all as specified and directed

M&L for Glazed ceramic tiles glossy serise digital wall tile 300 x 450mm x 7mm thick coloured on vertical surfaces set and jointed in neat cement slurry and pointed in white cement to match including 10mm thick rendering of CM 1:4 all as directed and specified.

M&L for Rendering 15 mm thick on unfair faces of brick work or concrete surfaces in CM (1:6) for finished even and smooth (without using extra cement) Complete all as specified and directed

M&L for Rendering 15 mm thick on fair faces of brick work or concrete sur-faces in CM (1:4) using water proofing compound @ 200ml by wt of cement per bag for finished even and smooth (without using extra cement) Complete all as specified and directed (WPC will be measured and paid separately)

Supply only liquid water proofing compound Complete all as specified and directed

M&L for 75 mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in plinth protection and paving finishing cone surface even and smooth without using extra cement Complete all as specified and directed

S&F of Steel ventilator with top hung shutter incl hinges, steel peg stary Complete all as specified and directed

S&F of 3.00mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane Complete all as specified and directed

Preparing of new steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamelled paint over a coat of Red oxide primer zinc crome. Complete all as specified and directed

S&F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as per specification.

S&F Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined to-gather with solvent cement as per specification.

S&F of Aluminium, anodised, barrel tower bolts of extruded section of 150 mm long

S&F of Aluminium handles, cast type, anodised of 100 mm size.

S & F PVC (SWR) floor trap plain or multi with stainless steel grating incl joining to waste pipe with solvent cement joint dia of outlet 75mm bore complete all as specified and as directed.

S&F of 100x100mm size Salt-glazed stoneware gully traps, square or round mouthed, tvpe 'P'

S&F of PVC grating 100mm dia fixed to floor trap

S&F of PVC Pipes 110 mm bore single socketed ,in any length with rubber ring joints,laid in trenches or in floors.

S&F of PVC (SWR) bends of radius 110 mm dia complete

S&F of PVC Pipes 75 mm bore single socketed ,in any length with rubber ring joints,laid in trenches or in floors.

S&F of PVC (SWR) 75mm bore junction single,(Single T) equal or unequal

S&F of GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floor in following bore of tube 15mm Complete all as specified and directed

S&F of GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floor in following bore of tube 20mm Complete all as specified and directed

S&F of GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floor in following bore of tube 25mm Complete all as specified and directed

S&F of Rotational moulded polyethylene water storage tanks Capacity 1000 ltr (cylindrical vertical with closed top) hoisted complete all as specified and directed.

S&F of PTMT Nipple 25 mm suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm- 45gms /25mm- 65gms) complete all as directed and specified

S&F of 25 mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass complete all as directed and specified

S&F of Vitreous China urinal half stall white coloured with Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F of Vitreous China wash basin, white, flat back of size 550x 400 mm incl cutting for and pining, in ends of brackets or erecting stand etc. complete all as specified and directed.

S&F of Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including provision of lime concrete bedding complete all as specified and directed.

S&F of 15 mm dia Pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F of waste fittings 32 mm bore, brass, chromium plated for basins etc with long screwed shanks and fly nuts, flange and bed deal in red lead cement and other end complete all as specified and directed.

S&F of PVC waste pipe 32mm dia and 65cm long for wash hand basin, complete all as specified and directed.

M&L for PVC connection 15 mm size with PTMT Nuts of length 450 mm complete all as specified and directed.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone and including 15mm thick screed bed in CM (1:4) incl grinding and polishing to be done by mechanical grinder and moulding of edges complete complete all as specified & directed.

M&L for Stop cock cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule for 15mm bore pipe all as specified

S&F of bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete.

S&F of PVC valve less syphonic action type flushing cistern 10 ltrs capacity low level white, with inlet ball valve, float and handle incl brackets complete all as specified and directed.

S&F of in brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F of 'P' or 'S' trap for EWC complete all as specified and directed.

S&F of Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

M&L for Rendering 5mm thick in cement mortar 1:3 as on concrete surfaces in ceiling finished even and smooth without using extra cement all as specified and directed

M&L for Preparation of new plastered surfaces of ceiling and applying three coat of white wash all as specified and directed.

M&L Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of wall care putty with preparation of newly plaster surface of wall complete all as specified and directed.

M&L for one coat of white cement based wall care putty whereever required complete all as directed and specified.

M&L for preparation of newly plastered surface of wall, pilasters, cornices etc and treatment apply two coats of Anti fungal weather coat acrylic emulsion paint over a coat of primer (X2) and over a layer of cement based wall care putty complete all as directed and specified. Make : (a) Asian (Apex Ultima), Berger weather coat all Guard, ICI Dulux (Weater shield Max), Nerolac (Excel Total). Make of primer : Asian (X2) or equivalent. Note : Each stages i.e. Preparation, Primer application, First coat and second coat of Apex will be passed by Engr-in-Charge. (b) Written warranty for four years is required to be furnished by the contractor for this item. Note : Putty shall be measured and paid saperately under respective item

Const of Septic tanks, exc, in ordinary soil, foundation In PCC 1:2:4, brick work in CM 1:4, RCC Slab covers including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame Vent shaft and sludge chambers etc., complete for 100 users. complete all as specified by TD DRG NO CEJZ/TD/57 sheet No 1/4 to 4/4 dated 05/05/2000

Const of Soakage wells exc, in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete of size 3.0 M dia X 3.0 M deep.complete all as specified by TD DRG NO CEJZ/TD/58 sheet No 1/1 dated 05/05/2000

M&L for Concrete bed (1:4 :8) type D2 using (40mm graded stone aggregate) for 200mm bore to drain pipes incl packing under & haunching against the sides of pipes after they are laid and tested;complete all as specified and directed.

Reinforced concrete pipes, class NP2 laid and jointed complete with collar for dia 200mm bore. complete all as specified and directed.

M & L for PCC (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) as in roof kerbs, mud stops,steps,coping small sumps and like items slightly rounded or chamfered on the edges complete all as specified & directed.

S&F of providing FRC manhole cover with rectangular frame of size 44"x26" MD-10 fixed at site up to satisfaction of Engr-in-Charge incl dismantling old manhole cover slab from site. complete all as specified and directed.

M & L for 25mm thick Plain cement concrete (1:2:4) type B-0, (using 12.5 mm graded stone aggregate) for levelling course in floors complete all as specified and directed.

M&L for rendering 10mm thick in CM (1:6) on other than fair faces of brick or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in CM (1:6) on fair faces of brick or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

S&F fabricating powder coated aluminium frame work,door shutter ,windows , ventilators, partisions with one or more rebates sections of approved tint as required for partions including beading,cleat, screws,fasteners, plugs, for fixing with wall/ceiling columns/beams etc complete all as specified and directed.

S&F aluminium power coated window and ventilator shutters, sliding type without sash bar alu section weighing 0.55 kg/m including necessary locking arrangement, guide wheels, joining cleats, glazing clips rubber packing anodised alu snap beading screws etc complete all as specified and directed.

S&F 5 mm thick plain or tinted glass, ordinary quality including rubber gasket for packing and fixed to aluminium doors/window/partition incl necessary cutting / moulding and chamferrring of edges for service window/counters complete all as specified and directed.

S&F 100 mm long mild steel butt hinges, cold rolled, medium weight complete all as specified and directed.

S&F for 125mm long anodised aluminium barrel tower bolt of extruded section complete all as specified and directed.

S&F 150mm long anodised aluminium handles, cast type complete all as specified and directed.

M & L for preparing new plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of cement primer and over a coat of 2 to 3mm thick wall care putty complete all as specified and directed.

Excavating in post holes (or similar holes) in soft/loose soil each not exceeding 0.5 Cum, getting out, reterning filling and ramming earth or broken rubber mixed with earth around in layers not exceeing 25 cm, watering and removing surplus soil to a distance not exc. 50m and making good surface complete all as specified and directed.

S & F steel work in tubular trussles, purlins, rafters, tubler column, where connected common rafter and running rails fixed with angle cleat or other connection plates including special shaped washers etc. complete using ERW or induction butt welded tubes confirming to Fe 410W grade E 250 quality B, etc complete all as specified and directed.

S & F 0.50mm thick (including coated thickness) Pre-colour, pre-profiled ( Galvalume ) sheets of required colour and design having tensile strength of 550 Mpa as in roof, wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer/ profile maker instruction complete all as specified and directed.

M & L for machine cut kota stone slab flooring 18 to 20mm thick (size not less than 550mm x 550mm) laid & jointed with grey cement mixed with pigment to match the shade of slab including rubbing and mirror polishing finished laid over and including 20mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

M & L for machine cut kota stone slab 22-25mm thick in riser of steps, skirting, dado and pillar and including laid over 15mm thick cement screed bed in CM (1:4) and jointed with pigment to match the shade of slab including rubbing and polishing complete all as specified and as directed.

M&L for PCC (1:2:4) type B-0 using 12.50mm graded stone aggregate as in sub base, levelling course, etc complete all as specified and as directed.

S & F for 2nd class hard wood as in plain, solid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed.

S&F for 35mm thick 2nd class hard wood plain, framed pannelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board wiyh commercial veneering on both faces. The size of rail and stile as per (IS : 1003 part-I , kiln seasoned and chemically pressure treated complete all as specified and as directed.

S & F for 30 mm thick factory made, 2nd class hard wood glazed and skeleton shutters, open rebeated and prepared to received glass, gauzed, with sash bar edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc, size of member of shutter as per specified in SSR Part-I Section 8, clause 8.24 (b) for window and fixed with chowkats, chemically pressure treated complete all as specified and as directed.

S&F for powder coated GI E-grid suspended false ceiling grid system 600x600mm with main runner 39x29.7x0.8mm, cross tee 39x27.7x0.80mm and wall angle 22.20x22.20x0.65mm ceiling suspended with 4mm dia GI wire hanger fixed with steel dash fasteners or from purlin of the roof with butterfly clips hold down clips etc complete main runner cross tee, wall angle of MS galvanized (PPC CGS) including 6mm thick HPSC pre-prime non asbestos fiber cement building board (E-classic) decorative finish fixed to aluminium / CGI frame work with hold down clips in false ceiling complete as all spesified

S&F Mild steel angle or flat iron, small articles such as hold fast , brackets, straps, cleats, etc for door/window chowkats including two coats of red oxide primer complete all as specified and as directed.

S & F for stainless steel wire cloth of 0.56mm dia wire and average width of aperture 1.18mm & fixed with tacks or screws, wire staples, etc complete all as specified and directed.

S&F 75 mm Butt hinges medium weight cold rolled mild steel and fixed complete all as specified and directed.

Preparation of new wood and wood based surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M&L for preparation of new plastered and apply two coat of exterior weather proof water base emulsion paint white/coloured over a coat of primer(same make) on walls complete all as specified and directed by Engr-in-Charge.

M & L for rendering 10mm thick in cement mortar 1:3 mixed with integral water proofing compound while concrete surface is green and finish the surface even and smooth without using extra cement all as specified and directed (WPC shall be measured and paid separately under respective item).

M & L for preparation of surfaces for applying bituminous primer (conforming to IS-3384-1965) @ 0.40 Kg/Sqm complete.

M & L for applying a tack coat of Industrial bitumen grade of 85/25 at the rate of 1.2 Kg per Sqm including cleaning surfaces (1st coat for bonding material below membrane and 2nd coat on top of membrane. Each coat would be paid seperately.)

M & L 3mm thick APP based polymeric membrane minimum weighing 3kg/sqm and reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed.Note: Application of APP membrane must be done by authorised applicator of membrane manufacturer.

M&L for applying two coats of bitumen based aluminium painting @ 0.15 Kg / sqm each coat on water proofing treatment with preparation of surface as on non assesible area complete all as specified and directed.

S&F CP pillar taps (swan neck type) cast copper alloy CP with capstan head, screwed down ,high pressure with long screwed shanks and fly nuts fixed in 15 mm bore pipes complete all as specified and directed.

S&F CP wall mixer for mixing hot & cold water screwed down for iron pipe 15mm bore complete all as specified and as directed.

S&Fixed 125 mm size chromium plated shower rose with siwel joint suitable for 15 mm bore GI pipes comlete all as directed.

S& F CP toilet paper holder complete all as specified and as directed.

M&L for plain Cement concrete (1:5:10) type E2 using 40mm graded stone aggregate in sunken floor complete all as specified and as directed

M&L Plain cement concrete (1:2:4) type B-0 using 12.50 mm graded stone aggregate) mixed with liquid water proofing compound as in padding, benching etc for sunken treatment etc complete.

Cutting and screwing existing steel tubing for addn/altern, bore dia of pipe 20mm, done in position without taking down

S&F 15mm bore chromium plated two way tab with flange fancy type, cast copper alloy, screwed down, high pressure with crutch or butterfly handle , screwed both ends for iron pipe or for unions complete all as specified and directed

S&F 15mm bore chromium plated health faucet incl flexible pipe 1.00 mtr long wall mounted and brass CP nuts complete all as specified and directed

M & L for Point wiring with FR LS PVC insulated PVC unsheathed electric cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area drawn in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good and matching disturbed surface of wall with existing surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit surface casing caping will be used) & 1.5 sqmm green FR LS PVC insulated unsheathed copper conductor as earth wire connected to earth dolly by providing lugs including galvanised boxes and bakelite sheet for mounting switches, sockets, fan regulators etc for One light point/fan point controlled by one switch .

(a) One light point/fan point controlled by one switch

(b) One 5amps socket out let point controlled by one switch on same board with other switches.

(c) One 5amps socket out let point on independent board controlled by one switch.

All as per item No-120 here in before but using PVC insulated unsheathed 2.5 sqmm cross sectional area cable for phase /neutral & for earth 2.5 Sq mm green PVC insulated cable for 15 amps socket point on independent board controlled by one switch.

S&F switch piano flush button single pole one way 5 Amp 240 volt complete as directed.

S&F socket outlet flush type 5 pin, 5 amps, 230 volts complete all as directed.

S&F switch piano flush button single pole one way 15 Amp 240 volt complete as directed.

S&F socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 230 volts complete as directed.

S&F ceiling rose surface bakelite three terminal complete all as directed.

Supply and fix integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 , Bajaj cat Pt No. BCLSB 18WH or equivalent in Wipro

Supply and fix integrated LED tube light fitting 1x9/10 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square box complete all as specified and directed .Make:- Havells Cat No. LHEXBLP7IN1W009 Bajaj Cat Pt No. BCLSB 10 WH or equivalent in Wipro

Supply and fix LED street light fittings 1x25 Watt, 5700K complete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible copper cable complete all as specified and directed .Make:- Havells Cat No.ENDURAPEARLSL25WLED757SASYTOPCMP Crompton Cat No. LSTO-25-CDL, Bajaj Cat No. BCLST 25W LED IV2

Supply and fix double door SPN DBs eight way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed by Engr-in-Charge.

S & F MCB SPN 6 to 32 amps 10 KA, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-in-Charge.

S&F MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-in-Charge.

M & L for Earthing complete with galvanized steel earth plate electrode 60cm x 60cmx 6.3 mm thick buried directly in ground ( earth pit not less than 2.25 meter deep below ground level) with the top edge of the earth plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate No.5 of MES SSR parts-I and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of PCC earth chamber in mix 1:3:6 type c-1 with 40 mm thick RCC 1:2:4 type B-J cover reinforced with 8mm dia MS bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia GI light grade and 15mm dia light grade pipe for earth lead protection and testing on completion complete all as specified and directed.

Supply and fixing of Exhaust fan of 230mm sweep, 230 Volts single phase, 900 RPM, complete with all accessories like nuts, bolts, louvers, shutters etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall and matching with the existing surface of wall complete all as specified and directed by Engr-in-Charge. Make : Havells Model Venti Air DB or equivalent in Bajaj/Crompton.

Supply and fixing of Exhaust fan of 300mm sweep, 230 Volts single phase, 900 RPM, complete with all accessories like nuts, bolts, louvers, shutters etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall and matching with the existing surface of wall complete all as specified and directed by Engr-in-Charge. Make : Havells Model Venti Air DB or equivalent in Bajaj/Crompton.

Supply,installation,commissioning of water cooler partially stainless steel, electric driven single phase having approx storage capacity 80 ltr and norminal cooling capacity 40 ltrs per hour. Make Blue star/Voltas/Shriram usha

M&L for Sub main wiring in repairs with two runs of single core FR LS PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including PVC insulated unsheathed FR LS 4.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge

Supply and fixing electric ceiling fan capacitor type 1200mm sweep, 230 volts single phase, ISI marked star rating, white in colour, complete with all accessories like down rod, clamps etc all as specified and directed by Engr in Charge

Material and labour for Single pole and neutral enclosure with a two pin and earth plug and socket complete with double pole MCB of suitable capacity

Supply & Fixing of Stop valve,15 mm, chromium plated fancy type cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

Supply & Fixing of PVC connection Heavy duty 18" long 15mm dia with 2 Nos brass check nuts suitable for cold water complete all as specified and directed.

Supply and laying LT cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10sq mm 2 core

Supply laying and jointing GI pipe 'light grade ' 40mm bore in trenches/under floors or roads/ along poles /on wall incl clamps for protection of cables incls fittings complete all as specified and directed.

M&L for clean and dry sand pavor black (un-washed) in trenches incl spreading and levelling for cushioning of UG cable complete all as specifed and directed

M & L for brick size sub class 'B' (modular size) laid flat in trranches for projection of cable complete all as specified and directed

Supply and fixing solar LED light fitting 40 watt with high efficiency all in one solar street ligh Mono crystalline solar PV module lithium Ferro Phosphate battery with in- built BMS technology , High efficency LED , MPPT solar charge controller and aluminium extruded body specially designed by progressive intelligent dimming which automatically control the dimming and brightness of light to enhance the back up , battery capacity 12 V 24AH, IP65, temp 5700 k complete all as specified.

Supply and fixing of GI tubing, medium grade 80 mm dia in pit vertically for solar light fitting with clamps , nuts bolts for fixing all as directed . Note : Excavation and PCC work will be measured and paid separately or relevant items.

J B CONSTRUCTION AND DEVLOPERS

Chitragupta Construction

M/S UnitedConstruction

APconstruction

M/S Sunshine Construction