REPAIRS TO ROOF MANGALORE TILES, FLOORING, JOINERY, PLUMBING IN SERVANT QTRS IN OMQ AREA AND REPAIRS TO PLUMBING, JOINERY, CEILING, TILING AND ALUMINIUM DOORS OF CERTAIN BLDGS IN WSA AT AF STN PUNE

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for cement concrete type B0 1:2:4 (12.5 mm graded agg) 25mm thick as in sub floors complete all as specified and directed.

M&L for coloured Non skid ceramic tiles of size 400x400mmx7mm thick in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for coloured Non skid ceramic tiles of size 300x300mmx7mm thick in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L Glazed Ceramic Coloured Tiles, 450 x 300 x 7mm in size, set on Vertical Surfaces such as Skirting, Dado, etc,over and including 10mm thick screed bed in cement mortar 1:3 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, complete all as specified and as directed.

M&L for vitrified ceramic tiles Dark shade 10mm thick (square/rectangular ) polished ,area of each tiles exceeding 0.36 sqm but not exceeding 0.42sqm in floors ,in floors and dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M & L for 75mm thick PCC 1:3:6 type C-2 using 40 mm graded agg finished even and smooth w/o using extra cement complete all as specified and as directed.

M & L for 50 mm thick PCC 1:3:6 type C-2 using 40 mm graded agg finished even and smooth without using extra cement complete all as specified and as directed.

Sand filling under floor or in foundation including watering and consolidation complete all as specified and as directed.

M&L for pre-cast concrete machine pressed rubber moulded glossy finished interlocking paver Block of 60mm thick M-35 grade any colour (as approved) and design Over sand cushioning complete including with using grey cement and pigment any shape and size confirming to IS-15658-2006 complete all as specified and as directed.

M&L for Coloured chequerred cement concrete exterior glazed tiles of size 30cmx30cmx20mm thick in floor laid and jointed in cement slurry and pointed in grey cement and pigment over 20 mm thick screed bed in CM (1:6) complete all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floor apron etc laid bedded and pointed in cement mortar complete all as specified and as directed.

M& L Kota stone slab flooring 20-25mm thick over cement screed base laid andjointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including screed bed 15 mm thick in cement mortar (1:4), including rubbing and mirror polishing complete all as specified and directed.

M& L Kota stone slab flooring 20-25mm thick as in vertical surface such as skirting and dado jointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including backing coat of 15 mm thick in cement mortar (1:4), including rubbing and mirror polishing complete all as specified and directed.

Dismantling wall & ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed.

S&F aluminium snap grid powder coated frame work for false ceiling, size of grid 605 x 605mm along with 4mm dia mild steel wire class 3 as in suspenders complete all as specified and as directed. Note : Rate included for necessary scaffolding to carry out the work up to 10 Mtr height.

S&F 10mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium complete all as specified and as directed. Note : Rate included for necessary scaffolding to carry out the work up to 10 Mtr height.

Taking down and refixing in same opening of chowkats or frames not exc 1.5 sqm each

Taking down and refixing in same opening of chowkats or frames exc 1.5 sqm n exc 4 sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each complete all as specified and as directed.

S&F 30 mm thick flush shutters, solid core with block board core and plywood face panels complete all as specified and as directed.

M & L for factory made solid PVC moulded door shutter , 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face supplying and fixing in frame at site as per specification & drawing complete all as specified and as directed.

S & F solid PVC door frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube fixed to wall complete all as specified and as directed.

Hacking out old broken glass (any thickness ,size ,quality or description ) from wooden frames or stone ,concrete or brick surrounds ,glazed with putty or fixed with beabs complete all as specified and as directed.

S & F sheet glass 3 mm thick, ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed.

S&F Aluminium handles, cast type, anodised 125mm long complete all as specified and as directed.

S&F aluminium, anodised barrel tower bolts of extruded section and fixed of size 200 mm long complete all as specified and as directed.

S&F aluminium alloy , anodised sliding door bolt with hasp, Staple ( bolt type) and fixing clips of sheet , cast or extruded section and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy and fixed length of bolt 300mm complete all as specified and as directed.

S&F 100mm butt hinges ,extruded aluminium alloy with galvanised mild steel hinge pin ,anodised and fixed ,type B-21complete all as specified and as directed.

M & L for 2 coats of synthetic enamel paint on wood and wood base surface of any description not otherwise described, over 10 cm width or girth over a coat of pink primer incl preparation of surfaces complete all as specified and as directed.

Aluminium anodized door shutter with frame of size 62.5x37mmx1.5mm thick with one or more rebate consisting of 5mm thick tinted glass pane, aluminum shutter having top, middle and bottom rail of size 112mmx37mm including jointing cleats, glazing clips, rubber packing, anodized snap beading, aluminum anodized fittings such as 200mm long tower bolt (2 Nos), 150mm hinges (3 Nos), suitable handles (2 Nos) mortice lock with 02 keys for each door complete all as directed including taking down of old frame with shutter of any description.

Aluminum anodized door shutter without frame aluminum shutter having top, middle and bottom rail of size 112mmx37mm including jointing cleats, glazing clips, rubber packing, anodized snap beading, one or more rebate consisting of 5mm thick tinted glass pane, aluminum anodized fittings such as 200mm long tower bolt (2 Nos), 150mm hinges (3 Nos), suitable handles (2 Nos) mortice lock with 02 keys for each door complete all as directed including taking down of shutter of any description.

Dismantling Roofing (corrugated ted, semi corrugated, etc.) sheets in roof coverings of any position complete all as specified and as directed.

Dismantling of Mild steel work complete all as specified and as directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running fixed with angle cleats or other connecting plates of grade Fe 410 W Quality A complete all as specified and as directed.

M & L applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces over 10 cm width or girth including preparation of new steel surfaces complete all as specified and as directed.

M & L for preparation and applying one coats of synthetic enamel paint on steel surfaces over 10 cm width or girth including preparation of new steel surfaces complete all as specified and as directed.

S&F pre painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/ridge/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Taking down of exist roof treatment including cement plaster complete all as specified and as directed.

M & L cement concrete type B0 1:2:4 (12.5 mm graded agg) 25mm avg thick as in roof complete all as specified and as directed.

M & L rendering 10mm thick in CM 1:3, using WPC @ 0.20 ltr per bags on roof surface complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thikc reinforced with polyster non woven fabric (wt not less than 150gms/sqm) laid on primed surface by torch application with 10 cm overlaps and Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq. m finally coating the surface with bituminous aluminum paint @ 100gm/Sqm complete all as specified and as directed.

Demolition of brick work /stone masonry/pcc block masonry built in cement mortar of any description complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry Type C-I 1:3:6 (20 mm graded aggregate) with solid block ,exc 10cm in width and set in cement mortar 1:6 complete all as specified and as directed.

Taking down cement plaster on brick/stone/concrete surface including wall tiling and hacking out joints hacking for key scrubbing down with water etc complete all as specified and as directed.

M&L for rendering 15mm thick in CM (1:6) on fair faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Preparing old treated plastered surfaces by washing, rubbing down surfaces and applying two coat of cement base paint in approved camoflauge pattern complete all as specified and as directed.

M&L for 10mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and as directed

M&L for preparing of new plastered surface of brick work, concrete plastered or unplastered surface and applying two coats of Acrylic smooth exterior paint of required shade (camouflag pattern) over a coat of primer, approved colour or pattern complete all as specified and as directed.

M&L for preperation of new plastered wall surface of any description and applying two coat of cement based camouflage pattern paint over a coat of chalk whiting complete all as specified and as directed.

M&L for preperation of new concrete /plastered surface of any description, applying three coat of white wash complete all as specified and as directed.

M&L for preparation of old concrete /plastered surface of any description, applying one coat of white wash complete all as specified and as directed.

M&L for preparing of old painted surface of brick work, concrete plastered or unplastered surface and applying one coat of weather proof exterior emulsion paint on walls complete in comouflage pattern complete all as specified and as directed.

Disconnecting existing tanks, setting aside including necessary connections (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (including Cleaning repairing etc).Capacity in litres Exc 250 & n exc 500 complete all as specified and as directed.

Dismantling water tank exc 250 and n.exc 500ltr capacity and removing from site complete all as specified and as directed.

S&F rotational moulded polyethylene cylindrical vertical with closed top water storage tank double layered 500 Ltr capacity, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection complete all as specified and as directed.

S & F in repairs 20 mm Brass valves ,high pressure,with polythene float and flynut complete,screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

Taking up or down steel tubing 15mm dia and connections including cleaning for refixing complete all as specified and as directed.

Taking up or down steel tubing 20 mm dia and connections including cleaning for refixing complete all as specified and as directed.

S & F 15mm dia medium grade GI tubing with all fitting and fixed to wall, ceiling or laid in floors etc complete all as specified and as directed.

Refixing only 15mm dia medium grade GI tubing with all fitting and fixed to wall, ceiling or laid in floors etc complete all as specified and as directed.

Refixing old steel tubing and connection 20 mm bore in new or old position in wall, ceiling and floor etc complete all as specified and as directed.

S & F 20mm dia medium grade GI tubing with all fitting and fixed to wall, ceiling or laid in floors etc complete all as specified and as directed.

S & F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and as directed.

Taking down PVC (SWR) pipes 110mm dia complete all as specified and as directed.

S & F 110mm bore PVC SWR pipe single socketed in any length fixed to wall complete all as specified and as directed.

S & F 110mm bore PVC (SWR) bends with access door complete all as specified and as directed.

S & F 110mm bore PVC (SWR) bends complete all as specified and as directed.

Disconnecting existing tanks, setting aside including necessary connections (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing etc. measured separately).Capacity in litres Exc 500 & n exc 1000 complete all as specified and as directed.

S & F Grating doom 100mm dia of PTMT including bedding and pointing in cement mortar 1:3 complete all as specified and as directed.

Galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanized wire staples complete all as specified and as directed.

300 mm MS ordinary rat tail rod pattern springs and including roller and roller plate complete fixed complete all as specified and as directed.

S & F PVC valveless, syphonic action type flushing cistern, low level, white,with inlet, ball valve, float and handle 10 ltrs capacity incl brackets in repairs complete all as specified and as directed.

S & F vitreous china wash basin white flat back size550x400mm excl chain and plug and porcelain stopper but incl CI bracket. PTMT waste coupling and PVC waste pipe 75 cm long and 15mm dia PVC connection etc complete in repair complete all as specified and as directed.

Bib tap cast copper alloy fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia fixed as in repairs complete all as specified and as directed.

Pillars taps fancy type cast copper alloy fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia fixed as in repairs complete all as specified and as directed.

Stop valve fancy type cast copper alloy chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia fixed as in repairs complete all as specified and as directed.

S&F Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed (Al die cast body) and fixed in repairs complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed ware /PVC/ AC or Reinforced concrete) set in cement mortar complete all as specified and as directed.

S&F 110/150mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F in repair cast iron Nahani trap with grating of diameter of outlet 100mm including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed.

M&L for cutting chases, pinning in making good to face for concealed water tubing complete all as specified and as directed.

S&F in repair 5mm thick float glass looking mirror of size 600x450mm with aluminium powder coated frame complete all as specified and as directed.

S&F in repair vitreous china, squatting pan of 'Orissa' pattern, long pan, size 580 mm x 440 mm, white, with 'P' of 'S' Trap, front or back inlet and foot rests any pattern, including concrete bedding and PVC low level flushing cistern 10 Ltr capacity including 32mm PVC flush pipe, all internal fitting, inlet, outlet pipe connections etc. complete all as specified and as directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming Fe 410 -W (Gde- E- 250) quality- AFe complete all as specified and as directed.

S&F in repair 15 mm Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm- 125gms) complete all as specified and as directed.

S&F Floor door stopper of brass alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

S&F in repair brass Mortice lock, vertical type, size 100 mm 4 Levers complete all as specified and as directed.

S&F PVC Weste pipe as in WHB Size 50 to 75mm complete all as specified and as directed.

S&F in repair 500 Ltr PVC Water Tank Cover complete all as specified and as directed.

S&F in repair 15 mm dia CP brass PVC connection 45 cm long including check nuts etc complete all as specified and directed

M&L Anti Termite Treatment under existing floor surface of any description using emulsion by injection methord (300 mm centre to centre hole destance) by means of mechanical injucter at the rate of one liter per hole of emulsion including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 Cement: 2 Coarse sand) to match the existing holes complete all as specified and as directed.

M&L Anti Termite Treatment of Voids in any type of masonry using emulsion by injection methord (300 mm centre to centre hole destance with a 45 degree slent) by means of mechanical injucter at the rate of 2.25 liters of emulsion per linear metre including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 Cement: 2 Coarse sand) to match the existing holes complete all as specified and as directed.

M&L Anti Termite Treatment along the external wall below concrete or masonry apron using emulsion by injection methord (300 mm centre to centre hole destance) by means of mechanical injucter at the rate of 2.25 liters of emulsion per linear metre including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 Cement: 2 Coarse sand) to match the existing holes complete all as specified and as directed.

S& F Collapsible steel gates, top hung, consisting for channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete including taking down old gate complete all as specified and as directed.

Taking down necessary parts of rolling shutters of any description area exc 4 sqm but n.exc 20 sqm each from brick/stone walls including top cover complete all as specified and as directed.

Fixing only rolling shutters of any type (obtained from Ser Item No 99.00 above) after making good & serviceable condition i.e. oiling, greasing & laths jointing complete all as specified and as directed. (Note Supply and fixing of any fittings or accessories required to replace shall be measured and paid separately).

S&F steel rolling shutters, without ball bearing manual type including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated complete with thickness of laths 1.25 mm complete all as specified and as directed.

S&F in repairs bevel gear box and crank hadle complete all as specified and as directed.

S&F in repairs steel tention spring for rolling shutters complete all as specified and as directed.

S&F in repairs ball bearing for rolling shutters complete all as specified and as directed.

Taking down doors frame with shutters (without taking of shutters from the frame ) of size exc 1.5 Sqm but n. Exc 4.0 Sqm each from brick/stone walls complete all as specified and as directed.

Taking down window/ventilator frame with shutters (without taking of shutters from the frame) of sizes n. Exc 1.5 Sqm each from brick/stone walls complete all as specified and as directed.

Forming jambs, etc, to openings (to foregoing item), including cutting, tooting and properly bonding into work, also facing, jointing and pointing to match existing work in CM (1:4) complete all as specified and as directed.

Dismantling of Single layer Mangalore pattern or similar tiles in roofing complete all as specified and as directed.

Dismantling of Battens for tiles, shingles etc, of any size including tilting fillets complete all as specified and as directed.

Dismantling timber scantlings 40 sq. cm and over in section, Framed work in any position complete all as specified and as directed.

Material and labour Second class hard-wood clean sawn as in scantlings fixed in framed work complete all as specified and as directed.

Supply and fix rolled mild steel as roof trusses (framed) purlins (angle, beam, tee channel) incl distance piece, cleats etc of Fe-410W (Gde E-250 quality A) with and including necessary cutting bending drilling holes welding, rebates etc, complete all as specified and as directed.

Taking/removing existing tar felt treatment from RCC roof slab/terrace by means of MS scrappers patty or any other suitable tools and removing debris to a distance exc 1.5 KM but n;exc 5 KM from the starting point and deposited where directed by Engr-in-charge.

Raking out joints/pointing cement mortar to random rubble or polygonal rubble uncoursed or brought up to courses complete all as specified and as directed.

M & L for Keyed pointing to random or polygonal rubble, uncoursedor brought upto course CM 1:4 complete all as specified and as directed.

M & L rendering bed 10 mm thick in CM 1:3 in averaging on RCC roof slab/terrace surfaces with mixing of WPC @ 3% by wt of cement complete all as specified and as directed.

M & L providing & laying APP (Atactic, polypropylene polymer) modified water proofing membrane with non woven polyester reinforcement 3mm thick, not less than 3.60 kg per sqm over a coat of bitumen primer for bitumen membrane @ 0.3 litre per sqm including a top coat of bituminous aluminum paint @ 100 gram per sqm complete all as specified and as directed.

Supply only integral waterproofing compound complete all as specified and as directed.

S & F steel windows with side hung shutters including projecting type hinges with glazing bars complete all as specified and as directed.

Ditto all as per Ser Item no 119.00 above but without glazing bars complete all as specified and as directed.

S & F Steel ventilator with top hung shutter including hinges ,steel peg stay complete all as specified and as directed.

S & F for second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

M & L preparing surfaces of wood and wood based materials new of any description and girth not otherwise described and treating with tar or coal tar black paint at ends of post back of chowkats etc area tarred exc. 0.10 Sqm but n.exc 0.50 Sqm each complete all as specified and as directed.

M & L for cement concrete 1:2:4 type B1 (20mm graded aggregate) in copings, bands ,for hold fast and back filling etc. complete all as specified and as directed.

S & F 35 mm thick second class soft wood glazed and Skelton shutters open rebated and prepared to receive glass, gauge etc (with out sash bars ) edges for receiving glass etc sizes of members of shutter as specified in SSR Part I section 8 clause 8.20 (a) s complete all as specified and as directed.

M & L for 1 coat of synthetic enamel paint on wood and wood base surface of any description not otherwise described, over 10 cm width or girth over a coat of pink primer incl preparation of old surfaces complete all as specified and as directed.

S & F for MS butt hinges med. Wt. cold rolled ,and fixed 100 mm size complete all as specified and as directed.

S & F Aluminum anodized handle Cast type 150 mm size complete all as specified and as directed.

S & F Aluminum anodized or powder coated tower bolts 150 mm length complete all as specified and as directed.

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

M & L for framed work such as grills or railing in design pattern etc with ends of bars shoulders rebated or forged in to spick confirming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F 20 mm bore ball valves high pressure PTMT with epoxy coated rod complete all as specified and as directed.

M & L for 40mm thick cement concrete type B1, 1:2:4 (20mm graded aggregate) as in floor finishing cement concrete surface even and smooth using extra cement complete all as specified and as directed.

S & F for glass dividing strips, 3mm thick and width of strip 38 mm complete all as specified and as directed.

M & L for rendering 15mm thick on brick work or concrete surface in CM 1:4 finished surface even and smooth with out using extra cement complete all as specified and as directed.

M & L for preparing new plastered surfaces and applying two coats of dry distemper on wall surface complete all as specified and as directed.

M & L for preparing old plastered surfaces and applying one coats of dry distemper on wall surface complete all as specified and as directed.

M&L Glazed Ceramic Coloured Tiles, 300X200X7mm in size, set on Vertical Surfaces such as Skirting, Dado, etc,over and including 10mm thick rendering in cement mortar 1:3 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, complete all as specified and as directed.

S & F in repair PVC low level flushing system plastic valve with inlet ball valve float chain and ball (of capacity 10 liters) ISI Marked incl 32mm PVC flush pipe complete all as specified and directed

greenstone construction

R K ENTERPRISES

BSK Construction

R k construction