REPAIR TO INTERNAL WATER SUPPLY AGE B/R-II, GE (SOUTH) UDHAMPUR

Amount

Checking and attending to water leakage from taps, flushing cisterns, wash hand basins and other sanitary fittings/fixtures and any obstruction to water supply, requiring plumber work and carryout minor repairs such as replacement of washers, check nuts, tightening of fittings of flushing cistern etc including petty materials like washers of all sizes, thread (shoot), M-seal, screws, nails to make water supply/ plumbing lines functional and leak proof complete all as specified and directed by Engr-in-Charge. Note : Any items required to be replaced shall be paid under respective items.

Note : (a) Contractors representative / Engineer will report to Engr -in -Charge / concern JE daily in morning to collect complain for routine / urgent works related to day to day maintenance till completion of contract. (b) All routine / urgent jobs received on docket slip shall be attended within 24 hrs. If the nature of job is such that which cannot be completed within 24 hrs, it shall be immediately brought in to the notice of Engr-in -Chrage, (c) The period for working to the such complains shall be decided by GE /Engr-in -Charge.If delay is more than 24 Hrs & GE/Enge-in-Chage is not satisfied with reason for delay in working then the penalty of Rs 350/complain/day shall be recovered from contractor (d) In case of any dispute arising from above,the decision of Accepting Officer shall be final and binding.

PVC tank lid for 500 to 1000 litre capacity including all locking arrangements, nuts, bolts etc for fixing complete all as specified and directed by Engr-in-Charge.

PVC tank lid for 2000 litr capacity including all locking arrangements, nuts, bolts etc for fixing complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description in ground floor and paving not exceeding 15 cm thickness (below or above ground level) including recoving the rubbish/debries out side MOD land complete all as specified and directed.

25 mm thick PCC type B-0 (using 12.50 mm graded crushed stone aggregate) as in sub base for laying floor finishes complete all as specified and directed.

50 mm thick, plain cement concrete type D-2, (1:4:8) (using 40 mm graded aggregate) as in sub base of floors complete all as specified and directed.

Taking down cement plaster, any description on brick or stone or cement concrete surfaces of walls including raking out joints, hacking for key, scrubbing down with water etc, including removing the rubbish/debries outside MoD land complete all as specified and directed.

15 mm thick rendering in two layer (10 mm + 5 mm) on fair faces of brick/concrete surfaces of walls in cement mortar 1:4 and finished even and fair without using extra cement complete all as specified and directed.

15 mm thick rendering in two layer (10 mm + 5 mm) on fair faces of brick/concrete surfaces of walls in cement mortar 1:6 and finished even and fair without using extra cement complete all as specified and directed.

Applying 3 mm thick birla wall care putty on oldplastered on wall surfaces including preparation of surface by brooming down or steel wire brushing, scrapping down vegetation growth, efflorscent salts and trading with oil greasy spot complete all as specified and directed.

Preperation of old decorated surface of walls and applying two coat of oil emulsion distemper complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars and similar work confirming to Fe-290, Grade E-165 complete all as specified and directed.

Disconnecting existing tanks, 500/1000 ltr capacity, setting a side (or lowering if reuired) for repairs, cleaning and removing all scale and dirt, etc from tanks and from mouths of circulating pipes, etc and hoisting if required reconnecting and re-fixing in position or removal to store complete all as specified and directed.

Disconnecting existing tanks, exceeding 1000 ltr but not exceeding 2000 ltr capacity, setting aside (or lowering if reuired) for repairs, cleaning, and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc and hoisting if required reconnecting and re-fixing in position or removal to store complete all as specified and directed.

Taking up or down 20 mm bore pipes steel tubing and connections complete all as specified and directed.

Taking up or down of 15 mm bore pipes steel tubing and connections complete all as specified and directed.

Steel water tubing of nominal bore 20 mm medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) including taking down old tubing complete all as specified and directed.

Steel water tubing of nominal bore 15 mm medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) including taking down old tubing complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing off the premises complete all as specified and directed.

Screed bed or bedding layers of 15 mm thick cement mortar 1:6 for laying floor finishes complete all as specified and directed.

Rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces for backing coat of wall tiles etc complete all as specified and directed.

Non skid light coloured, white printed tiles 300 x 300 x 7 mm thick in floors etc set and jointed in neat cement slurry pointed in white or coloured cement to match complete all as specified and directed.

Glazed ceramic tiles of size 300 mm x 200 mm x 6 mm thick coloured tiles on vertical surfaces set and jointed in neat cement slurry and pointed in white cement mixed with colour pigments to match the existing surface complete all as specified and directed.

Brass spindle for bib tap and mixer stop cock, including all necessary washers, nuts and screws fixed "as in repair" complete all as specifed and directed.

Cutting of existing main GI pipe line 15 mm to 20 mm bore for making arrangement for connection of any size including all GI fitting (each cut shall be measured separately) complete all as specified and directed

GI socket, Tee, Elbow, Union, Reducer, Plug15 mm dia medium weight fixed "as in repair" complete all as specified and directed.

GI socket, Tee, Elbow, Union, Reducer, Plug 20 mm dia medium weight fixed "as in repair" complete all as specified and directed.

GI nipple 15 mm dia, 100 mm long medium weig ht fixed "as in repair" complete all as specified and directed.

GI nipple 15 mm dia, 150 mm long medium weight fixed "as in repair" complete all as specified and directed.

Viterous china squatling Pan Orisa pattern size 580mmx440mm white, with integral feat rests including connection to trap and to flush pipes etc and excluding flushing cistern and flush pipes fixed "as fixed in repair" complete all as specified and directed.

Vitreous china wash down water closet pan (pedestal pattern) white plastic water closet seat and back with flat bottom and cover, mild steel chromium plated or aluminium anodised high device (excluding flushing cistern and flush pipe) but including fixing bolt and necessary connection with existing pipes complete all as specified and directed.

Vitreous china wash basin, white, flat back size 550 x 400 mm, excluding taps, waste chain, plug and porcelain stopper but including brackets, flush pipe, cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed.

10 ltrs capacity PVC valve less syphonic action type, low level flushing cistern, white, with inlet, ball valve float and handle including brackets complete all as specified and directed.

15 mm bore pillar tap, fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanuls and fly nuts, screwed for iron pipe or for brass ferrule complete all as specified and directed.

15 mm bore bib taps, long body with wall flange with arreator fency type chromium plated cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Concealed stop cock with sheet flange cast copper alloy, screwed down high pressure, with crutch or butterfly handles for 15 mm bore pipe or for unions complete all as specified and directed.

15 mm dia 450 mm long PVC connection pipe with two PVC PTMT nuts at each ends with rubber washer complete all as specified and directed.

32 mm dia PVC waste pipe complete all as specified and directed.

Hand shower (Health faucet) brass body with 8 mm dia 1 mtr long SS braided flexible tube with wall hook fixed "as in repair" complete all as specified and directed. Make:- CERA Cat Part No-CG105A or equivalent in Jaquar/Kohler

Toilet paper holder brass chromium plated with flap complete all as specified and directed.

75 mm dia PVC (SWR) floor trap plain, with grating including jointing with solvent cement all as specified and directed.

Plastic water closet seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed.

125 mm dia chromium plated swivel type shower rose with arm and wall flange complete all as specified and directed suitable for 15 mm bore pipe.

CP soap dish any type fixed to plags with brass screws complete all as specified and directed.

Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall of including fixing cantilever brackets and connecting union to pipe complete all as specified and directed.

Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

1 mm thick plate rack made of stainless steel, 600 x 750 x 250 mm (Weight not less than 7.5 Kg) including brackets and embedded in brick wall complete all as specified and directed as per manufacturers instruction.

Water closet pedestal pattern colour (as approved by Engineer-in-Charge) Make CERA, Cat Part No : (EWC 2025 cistern 2115 Seat cover 2315 Twin flush cistern 2205/BT CLAIR DELUXE or equivalent of Jaquar/Kohler complete all as specified and directed.

Wash hand basin counter/cabinet type complete fitting as per sample approved and complete all as specified and directed by Engr-in-Charge. Make : Cera /Hindware/perryware

Chromium plated waste coupling including 32 mm dia PVC waste pipe flexible with minimum length 800 mm, fixed "as in repair" complete all as specified and directed.

Long body Bib Cock with wall flange suitable for 15 mm bore pipe complete all as specified and directed. Make : Cera/Hindware/Perryware or equilent.

Angular stop cock with wall flange suitable for 15 mm bore pipe complete all as specified and directed. Make : Cera/Hindware/Perryware or equilent.

Single towel rail 600 mm long complete all as specified and directed. Make : Cera/Hindware/Perryware or equilent. .

Tumblar holder complete all as specified and directed. Make : Cera/ Hindware/Perryware or equilent..

Toilet paper holder with flap complete all as specified and directed. Make :Cera/ Hindware/Perryware or equilent..

Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

All as per Srl item No 59 herein before above but with aluminium alloy brackets and guard rail complete all as specified and directed.

450 mm long braided hose with M10 X 1 Nipple 15 mm Nut, O ring and rubber washer (Suitable for basin mixers) complete all as specified and directed. Make : Jaquar Cat Part No : ALD 805B or equivalent CERA/PRAYAG

450 mm long braided hose with M10 X 1 Nipple 15 mm Nut, O ring and rubber washer (Suitable for basin mixers) complete all as specified and directed. Make : Jaquar Cat Part No : ALD 803AB or equivalent CERA/PRAYAG

Hand shower (Health faucet) with 8 mm dia 1 mtr long flexible tube and wall hook complete all as specified and directed.

15 mm bore centre hole basin mixer with round spout with 450 mm long copper pipes and brass nuts with out Pop up complete all as specified and directed.

Towel rack of stainless steel including fixing arrangement complete all as specified and directed.

Looking mirror with wooden frame of required size complete all as specified and directed by Engr-in-Charge.

75 mm bore cast iron floor trap with grating including jointing to waste pipe fixed cement concrete type B-1 (1:2:4) complete all as specified and directed.

Stainless steel grating 75/100 mm complete all as specified and directed.

Vitreous china urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1: 2 securing urinal to plugs with and including 60 mm long brass screws, pinting around urinal back in cement fixing automatic flushing cistern with brackets, flush pipel grating and union for discharge pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

15 mm bore central hole basin mixer (wall mounted) brass chromium lated with round spout with pop up waste system with 450 mm long braided hoses & base flange brass nuts fixed complete all as specified and directed. Make:- CERA, Cat Part No : CS915 or equivalent PRAYAG/Perryware

15 mm bore sink mixer (wall mounted) with 304 mm (12") swival long spout connecting legs and wall flanges fixed complete all as specified and directed. Make : Cera, Cat Part No : CS919 or equivalent of Prayag /Perryware

15 mm bore wall mixer with telephone shower arrangement fixed complete all as specified and directed. Make : Jaquar, Cat Part No : FON-40147 or equivalent Prayag /Perryware

Sensor for urinals fixed "as in repairs" complete all as specified and directed. Make : Hindware/Cera/Perryware

Cabinet mirror with PVC body and shutter including in built shelves fixed complete all as specified and directed. Make :- ARKO/ Jindal/Prayag or equivalent

Dismantling water tanks capacity exceeding 250 and not exceeding 500 litres complete all as specified and directed.

Rotational moulded polyethylene with lid (three layer) water storage tank (cylindrical vertical with closed top) hoisted and fixed in position of capacity 500 litres and making inlet out let washout connection with all necessary accessories and fittings fixed complete all as specified and directed. Note : Tanks have thread mode shall ony be provided.

Rotational moulded polyethylene with lid (three layer) water storage tank (cylindrical vertical with closed top) hoisted and fixed in position of capacity 1000 litres and making inlet out let washout connection with all necessary accessories and fittings fixed complete all as specified and directed. Note : Tanks have thread mode shall ony be provided.

Rotational moulded polyethylene with lid (three layer) water storage tank (cylindrical vertical with closed top) hoisted and fixed in position of capacity 2000 litres and making inlet out let washout connection with all necessary accessories and fittings fixed complete all as specified and directed. Note : Tanks have thread mode shall ony be provided.

Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 15 mm dia (minimum weight 142 gms), suitable for flushing cistern 10 liters capacity complete all as specified and directed.

Ball brass valve 15 mm dia, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. Note : Contractor shall make his own arrangements like ladder etc at his own cost required for inccessible roofs.

Ball brass valve 20 mm dia, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. Note : Contractor shall make his own arrangements like ladder etc at his own cost required for inccessible roofs.

Gun metal globe or gate valves high pressure with polythene float and fly nut complete screwed for iron pipe or for unions of 15 mm bore and fixed in repair complete all as specified and directed.

Gun metal globe or gate valves high pressure with polythene float and fly nut complete screwed for iron pipe or for unions of 20 mm bore and fixed in repair complete all as specified and directed.

Towel ring square with round flange complete all as specified and directed. Make : Jaquar, Cat Part No : ACN-1121N.

Toilet paper holder complete all as specified and directed. Make : Jaquar, Cat Part No : ACN 1155N or equivalent

Towel rack 600 mm long with out lower hangers but with three hooks complete all as specified and directed. Make : Jaquar Cat Part No : ACN 1181N or equivalent ARKO/ Jindal/Prayag

Cleaning and removing all scale and dirt, etc from tanks and from mouths of circulating pipes, exceeding 250 Ltrs and not exceeding 500 Ltrs etc complete all as specified and directed.

Dismantling water tanks capacity exceeding 500 and not exceeding 1000 litres complete all as specified and directed.

Dismantling water tanks capacity exceeding 1000 and not exceeding 2000 litres complete all as specified and directed.

M/S ASHOK KUMAR PACHIALA

RAMAN CONSTRUCTION CO

anil construction co.