89/EDCB/2023-24

Amount

The work of safe carriage of the following material from store center Nawada to work site under the jurisdiction of EDD-I, Budau0n Approx. distance upto 0-20 Km. Including safe loading and unloading.

11/0.4 KV 25 KVA T/F

11/0.4 KV 63 KVA T/F

11/0.4 KV 100 KVA T/F

11/0.4 KV 250 KVA T/F

PCC Pole Support 8.5 Mtr. Long

ST Pole Support 11 Mtr. Long

11 KV MS T-Off Channel

Top Channel (125x65x2240 mm)

S/S Base Angle (75x75x6x2028mm) bolt & Nut

11 KV Disc Insulator Composite 45 KN (T&C Type)

11 KV Pin Insulator Composite

11 KV X-Arm V Type

11 KV TPMO

ACSR Weasal Conductor

L.T. LEAD LT XLPE Cable 3.5x70 Sqmm

L.T. LEAD LT XLPE Cable 3.5x150 Sqmm

Stay Complete

Earthing Complete

ABC Cable (3x95+1x35+1x16) sqmm

ABC Cable (3x120+1x35+1x16) sqmm

3 Phase Distribution Box

L.T. Cable 1x240 Sqmm

Construction of 250 KVA T/F plinth 1.5x1.5x2 Mtr. for mounting T/F including foundation work (below ground 0.5 M), Brick work, RCC slab of 4” thickness and plastering in 1:6 ratio with 02 Nos channel pieces of 1.5 mtr long of size 100x50x6 mm compete in all respect as per RESSPO Norms.

Cage fencing of 250 KVA Plinth mounted transformer in Town areas to avoid electrical human/cattle accidents by fabrication of cage (1 Inch Sq wiremesh) made of 10 No gauge in suitable size angle iron frame of size 7.5'(L)x5'(W)x8’(H) by strenghtening of wire mesh 20x3 mm M.S. flat haorizentally as well as vertically, Grouting the panel with 1:2:4 cement/coorse send/brick ballast. The Frame should be bolted on angles at the four corners so that frame may be un-bolted/bolted at the time of replacement of the transformer. Provision of 1 gate should be there for maintenance of the transformer. Painting (1 coat of red oxide + 2 coat of Bus green enamel paint). The wire mesh should be earthed with 50x6 mm MS earthing strip with existing earthing of Transformer Body. All men, material and T&P provided by the contractor to complete the fabrication, transportation and installation.

Pipe Earthing of Transformer (By boring of 4 inch diameter 20 m deep, 40 mm diameter A Class GI pipe is inserted to a depth of 20 m and a holed pipe of 1.5m length is inserted at the bottom, Tighten one end of the MS strip of size 50x6mm with the nut bolt with the neutral of the converter and weld the other end with the GI pipe inserted in the boring for earthing. Putting a socket on the upper part of the pipe (mouth) so that water can be poured into it to retain moisture. To complete the work contractor will provide all material, manpower, T&P, safe carriage of material to worksite. Above work will be carried out under supervision of concerned JE/SDO/EE).

Grouting of PCC 8.5 Mtr. Long/ST Pole 11 Mtr. Long with 1:4:8 mixture in size(450x450x1500mm.) including cost of cement/C.C. & sand Required as per RESSPO Norms. (All Grouting material shall be provided by the contractor).

Dismentaling of 10 KVA Transformer as per norms complete in all respect

Construction/Erection of Double Pole (except pole) Suitable for following T/F including fitting of all accessories (All necessary clamps, Nut & Bolts etc. shall be provided by the contractor for execution of work as per RESSPO Norms).

11/0.4 KV 25 KVA T/F

11/0.4 KV 63 KVA T/F

11/0.4 KV 100 KVA T/F

Mounting of following T/F,s as per norms complete in all respect -

11/0.4 KV 25 KVA T/F

11/0.4 KV 63 KVA T/F

11/0.4 KV 100 KVA T/F

11/0.4 KV 250 KVA T/F

Erection of Single PCC Pole 8.5 Mtr in H.T/L.T lines including fitting of all accessories as per RESSPO Norms (All necessary clamps, Nut & Bolts etc. shall be provided by the contractor for execution of work as per RESSPO Norms).

Laying, Stringing, Sagging & Jumpring of Following Conductor complete in all respect as per RESSPO Norms.

ACSR Weasal Conductor

L.T. LEAD LT XLPE Cable 3.5x70 Sqmm

L.T. LEAD LT XLPE Cable 3.5x150 Sqmm

ABC Cable (3x95+1x35+1x16) sqmm

ABC Cable (3x120+1x35+1x16) sqmm

Erection/Fixing of stay set with stay wire and clamp as per RESSPO norms including binding. climbing, clamping, tightening and nozzeling etc. complete in all respect including its grouting in ratio 1:4:8 of cement, sand and C.C. and sand etc. as per RESSPO norms. All the grouting material shall be provided by the contractor.

The work of driving the earthing electrode and making connections with GI wire.

Installation, Fixing & Fabrication of 11 KV fuse set (Including Cost of Fuse set) Installed on midway of 11 KV double pole structure with mention material specification (MS Channel 100x50x2028mm), Iron Strip (50x5x305 mm) & Fuse wire of required capacity etc. shall be provided by the contractor for execution of work as per RESSPO Norms.

Fixing of danger board on each location and G.I. barbed wire including proper clamping as per RESSPO Norms. (Danger Board shall be provided by the contractor as per RESSPO Norms).

Erection/Fixing of Tailess Unit (400 A) (Tailess Unit shall be provided by the contractor as per RESSPO Norms). complete in all respect.

Erection & Fixing of 11 KV TPMO set with handle on existing double pole including providing of clamps and nut & Bolts and jumpering of both side by TPMO.

Errection and commissioning of 3 Phase distribution box on the LT Poles (All the material required shall be arranged by the contractor for errection and commissioning of distribution boxes except distribution box).

The following Decentralized material shall be provided by the contractor for execution of work as per RESPO Norms (the material shall be purchased from approved vendor of Discom).

Holding Clamps for S/s with Bolt & Nuts

Holding Clamps for LT T-OFF

11 KV F Clamp with Nut & Bolt

X-Arm Holding Clamp with Nut & Bolt

PG Clamp

Stone Pad

Danger Board

Barbed Wire

Al. Lugs for 150 KV Sqmm Cable

Al. Lugs for 240 KV Sqmm Cable

LUGS OF Suitable Size (70 sqmm)

Stay Insulator

LT Tailess Unit (400A)

Safe back carriage of Following item (if any) from work site to Store Center, Nawada, Budaun approx distance upto 0-20 Km including loading & unloading.

11/0.4 KV 10 KVA T/F

M/S TIWARI TRADING COMPANY