ROVN OF TOILET BLOCK AND ALLIED INFRASTRUCTURE INCLUDING SEPTIC TANK AT CERTAIN LOCATIONS AT MIL STN JAISALMER

Amount

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in any type of soil all as specified & directed by Engineer-in-Charge

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in soft/disintegrated rock complete all as specified & directed by Engineer-in-Charge

Returning filling in soil including spreading, levelling and well ramming in layers n.exc 25cm thick in layer etc all complete.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in Soft/disintegrated rock.

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point

Removing Excavated rock not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point in Soft/disintegrated rock.

M&L for plain cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete all as specified & directed by Engineer-in-charge.

M&L for plain cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in foundations, filling & mass concrete all as specified & directed by Engineer-in-Charge.

M&L For Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering

Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 Type D-2 using 40mm graded stone aggregate as in sub bases all as specified.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified & directed by Engineer-in-charge.

Squared rubble walling, Jodhpur type, brought upto courses, well bounded, bedded and solidly hearted built in CM (1:4) complete.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified & directed by Engineer-in-Charge.

M&L rendering 15mm thick in 1:6 cement plaster on stone masonary surface is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L rendering 15mm thick in 1:4 cement plaster on of stone masonary surface is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L rendering 15mm thick in 1:4 cement plaster on of f brick work or concrete surfaces is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for 10 mm thick , plaster in cement mortar (1:4) on surfaces of ceiling and finishing the surface even and smooth without using extra cement all as specified & directed by Engineer-in-charge.

M&L for keyed pointing in cement mortar (1:3) to squared rubble masonry, Jodhpur type, coursed or un coursed all as specified & directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces as in wall, applying 3 coats of white wash complete.

M&L for preparation of new plastered surfaces as in ceilings, applying 3 coats of white wash complete.

Complete preparation new surfaces of walls and preparation of surfaces (external faces) of walls and applying two coats of external weather proof paint of Apex or equivalent over a coat of primer (self coat) complete all as per manufacturers instructions, complete all as per specified and directed.

M&L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates,Fe 410-W (Gde E-250) quality A

M&L for jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted, set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete complete all as specified and as directed by the Engineer-in-Charge

M&L for PCC 1:2:4 type BO using 12.5 mm graded stone aggregate for levelling course for consolidated thickness shall be varied from 25 to 85 mm as per the requirements all as directed by Engr-in-Charge.

M&L for 50 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate in Padding all as specified.

M&L for rendering 15 mm thick plaster in cement mortar (1:4) mixed with WPC on concrete surfaces of roof top and finishing the surface even and smooth without using extra cement all as specified and directed by Engineer-in-charge. Note :- WPC will be measured & paid seperately as supply only).

Supply only integral water proofing compound.(ISI Marked)

M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt not less than 150 gms/sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 Ltr/Sqm by forced all as specified and as directed

M&L for Non skid ceramic tiles , Light Shade, 10mm thick (square/ rectangular) polished, area of each tiles exc 0.11 sqm but not exceeding 0.18 Sqm, in floor/skirting etc set jointed and pointed in white or coloured cement to match the colour of tiles with screed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6. all as specified.

M&L for non skid ceramic coloured tiles of size 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, as in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over including screed bed or bedding layer of 15mm thick in CM (1:4) over 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate as base of flooring complete all as specified & directed.

S&F glazed ceramic coloured tiles of size 350 x 250mm x 7mm /450mmx350mmx7mm/450mmx300mmx 7mm thick on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15mm thick backing coat in CM (1:4) all as specified and directed by Engineer-in-charge.

M&L Glazed ceramic coloured tiles in vertical surface 600mm x300mm , 7-8mm mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering CM1:4 complete all as specified and directed.

S&F PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per Engr - in - charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suplying & fixing in the frame at site as per directed by Engr - in- charge.

S&F SS hinges, 100mm size and fixed.

S&F Aluminium anodised, barrel tower bolt of extruded section and fix of length 125mm

S&F aluminum anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified .

S&F Aluminium handles, cast type, anodised of size 150mm long.

S&F 150 mm size extruded aluminium handle, fabricated type, anodiesed complete all as specified & directed by Engineer-in-charge.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F 200mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed

S&F Factory made Box Type steel ventilators fixed type, incl with one shop coat of primer,complete as shown in Drawing No. CEJZ/TD/24 sh 1/1 to 1/3, and all as specified & directed.

M&L for sheet glass 4.00mm thick, ordinary quality and glazing with, rubber packing exc 0.5 sq m in each pane complete all as specified and as directed by the Engineer-in-Charge

S&F figured glass, pin head type & glazing with oil putty in square n exc 0.5 sqm in each pane 3 mm thick

M&L for roughly squared stone 5cm thick as in lintels n exc 3m in length, hammer dressed on face and soffits, hoisted, set and pointed in lime mortar 1:3 or cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge

M&L for 5cm sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete complete all as specified and as directed by the Engineer-in-Charge

M&L for 50 mm thick PCC (1:3:6) type C-1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25&3 parts of sand by weight all as specified and directed by Engr-in-charge

Supply and fix rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR part-I ,1000 ltr capacity

S&F 500 ltrs capacity white colour three layer rotational moulded polythene water storage tank (Cylinderical vertical with closed top) hoisted and fixed in postion all as directed by Engg-in-Charge

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

S&F Medium grade GI tubing 15 mm bore with all fittings , to walls, ceiling or laid in floors etc.

S&F Medium grade GI tubing 20 mm bore with all fittings , to walls, ceiling or laid in floors etc.

S&F gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed to 20 mm bore pipe.

S&F gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed to 50 mm bore pipe.

S&F stop cock copper alloy but fancy type and chrominum plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron/pipe or for union and fixed 15 mm bore

S&F 15mm bore bib taps cast cipper alloy chromoum plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule

S&F Viterious china White Wash Hand Basin fixed in repairs includign 15 mm pillar cock cast copper alloy CP, 15mm cast copper stop valve, 32 mm brase CP waste fitting, PVC waste pipe 32 mm dia & 15 mm PTMT connection pipe 450 mm long

S&F for European type water closet,including plastic seat cover white, closed pattern with flat bottom and mild steel chromium plated or aluminium hinging device complete.

S&F vitreous china squatting pan orissa pattern complete of size 580 x 440 mm white with intagral foot rest and making good to the floor complete.(Cera Cat part No-S3010104, Hindware cat no 20042)

S&F CP Health faucet spray with 1.5m long pipe with wall hook & fixed in repair complete

Supply and fix Bib taps two way type , cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule 15 mm bore and fixed

S&F PVC connections 15 mm size with PTMT nuts to length 450 mm

S&F PVC flushing cistarn 10 ltrs capacity ISI marked incl PVC damtake pipe PVC 450mm inlet etc all complete .

Cutting holes in to or through in brick or stone walls built in cement mortar and making good in CM 1:3 or cement concrete 1:2:4 type B1 as required, exc 150sqcm & n exc 400 sqcm complete all as specified and directed,

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm dia out let

PVC (SWR) multi floor trap with grating including jointing with solvent cement 100 mm dia out let.

S&F PVC (SWR) pipes of 110 mm dia, single socketed fixed to walls

S&F PVC (SWR) pipes of 75 mm dia, single socketed fixed to walls

S&F PVC (SWR) bends of 110 mm dia, any radius

S&F PVC (SWR) bends of 75mm dia, any radius

(PVC (SWR) vent cowl, 110 mm dia

(PVC (SWR) vent cowl, 75 mm dia

S&F in PVC (SWR) T equal or un-equal 110mm dia.

S&F in PVC (SWR) T equal or un-equal 75 mm dia.

S&F PVC (SWR) 100mm dia p or s trap all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors as waste & vent pipes complete all as specified & directed by Engineer-in-charge.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors as waste & vent pipes complete all as specified & directed by Engineer-in-charge.

S&F stop valve, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 20 mm bore iron pipe or for union complete all as specified & directed by Engineer-in-charge.

S & F 20mm stop cock fancy type cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends or for unions etc

S&F PVC ball valve 20mm dia high pressure of PTMT with polythene float and fly nut with epoxy coated aluminum rod complete screwed for iron pipe or brass ferrule all as specified & directed by Engineer-in-charge.

S&F in repair, salt glazed stone ware gully traps square or roung mouth of size 150x150 mm, type 'P' complete all as specified and directed by Engineer-in-charge.

S&F, in repair, viterous china bowl urinal flat back, size of 465 x 355 x 265mm white (Minimum) with grating and union for discharge pipe including providing & fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified & directed by Engineer-in-charge.

S&F in repair vitreous china wash basin white, flat back of size 550 x 400 mm white including waste fittings, brass, chromium plated, coupling, waste pipe, brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe complete all as specified & directed by Engineer-in-charge.

M&L for 10mm thick precast cement concrete Type C1 1:3:6 (20 mm graded aggregate) solid building blocks or slabs (with plain or interlocking joints as directed) setting in mortar, complete, in walls Set in cement mortar 1:6

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement.

S&F extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed butt hinges type B-21, 100 mm long, complete all as specified.

S&F 20mm Ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed

M&L for 10 mm thick rendering on fair faces of brick /concrete surfaces as in ceiling in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified.

M&L for applying two coats of cement base paint after preparation of newly plastered surfaces complete all as specified.

S&F in repair CP grating(with & without hole) for Nahani trap and floor trap of size 100 mm dia fixed in repairs

S&F Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed by Engineer-in-charge.

S&F 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia & PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified & directed.

S&F chromium plated Angle valve 15mm complete all as specified and directed by Engineer-in-charge.

S&F pillar taps 15 mm bore cast copper alloy with capstan head chromium plated screwed down high pressure with or without 'Hot' & 'Cold' with long screwed shanks and fly nuts, screwed.

S&F Vitreous china urinals with urinal spreader, half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing (Cera Cat Part No- S4020102,Hindware Cat Part No-60002, Jaquar URS-WHT-13261)

Surface Excavation n. exc 30 cm and averaging 15 cm deep and getting out any type of soil.

M&L for even spreading of 25 mm thick layer of sand cushioning all as specified & directed by Eng-in- Charge.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade With grey cement and no pigment

M&L for precast cement concrete Kerb stones of PCC 1:2:4 Type B-1 using 20mm graded stone aggregate set in cement mortar 1:4 including rounded or champhered all as specified and directed.

M&L for cement screed 10mm thick in cement mortar (1:4) on concrete surfaces finishing the surface even and fair.

S & F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square in n exc 0.5 sq.m in each pane.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified & directed by Engineer-in-charge. Note :- To be fixed at any floor level not more than triple storey.

M&L Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.

M&L for Pre-cast cement concrete block masonry with solid blocks,Type C1 1:3:6 (20 mm graded aggregate exc. 10 cm in width and setting in mortar, complete,Set in cement mortar 1:6

Pre-cast cement concrete block masonry Type C1 1:3:6 (20 mm graded aggregate) Set in cement mortar 1:4 with solid blocks, exc. 10 cm in width and setting in mortar, complete

M&L 200 mm dia salt glazed stoneware drain pipe (SGW) grade 'A' laid in trenches and jointed in CM (1:3) demolition and breaking up drain pipes including cement bedding and haunching complete and removing debris outside MD land complete all as specified and as directed

M&L 150 mm dia salt glazed stoneware drain pipe (SGW) grade 'A' laid in trenches and jointed in CM (1:3) demolition and breaking up drain pipes including cement bedding and haunching complete and removing debris outside MD land complete all as specified and as directed

Material & Labour for cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested in bore of pipe 200 mm complete all as directed.

Septic tanks, excavaation in any type of soil, foundation in PCC 1:2:4, stone masonary in CM 1:4, RCC slab covers including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame vent shaft and sludge chambers etc complete for 20 users. (Refer TD drg No. CEJZ/Td/31 dt 14 Dec 2013 Sheet No. 1/3 to 3/3.)

Soakage wells excavation in any type of soil, foundation in PCC 1:3:6, wells of honeycomed and solid in M-25 concrete, including intercepting chamber, screed chamber, stone masonary work in CM RCC cover slab in M-25/RR masonary/Filling with brick bats complete for 20 users. of size 1.2 m x3.00 deep. (Refer TD drg No. CEJZ/Td/29 dt 14 Dec 2013 Sheet No. 1/3.)

Soakage wells excavation in any type of soil, foundation in PCC 1:3:6, wells of honeycomed and solid in M-25 concrete, including intercepting chamber, screed chamber, stone masonary work in CM RCC cover slab in M-25/RR masonary/Filling with brick bats complete for 20 users. of size3.00 m x4.50 deep. (Refer TD drg No. CEJZ/Td/29 dt 14 Dec 2013 Sheet No. 1/3.)

M&L for plain cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straigth or curved) complete all as specified & directed.

Cement concrete ( 1:2:4) type B-1 using 20mm graded stone aggregate as in surface channels & drains etc.

Extra over for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement, including form, moulds, mitered/stopped ends etc.

M&L for reinforced concrete NP2 drain pipes 150 mm dia confirming to IS laid in trenches and jointed in CM 1:2 all as specified & directed by EIC

Concrete bed to drain pipes including packing under und haunching against the sides of pipes after they are laid and tested in PCC 1:4:8 type D-2 for 150mm bore pipe.

Concrete bed to drain pipes including packing under und haunching against the sides of pipes after they are laid and tested in M-10 (nominal mix) using 20mm graded for 150mm bore pipe.

Mild steel TMT bars 6 to 8mm dia cut to length, bent to shape required including cranking, bending spirally for hoping for columns, hooking ends binding with MS wire (annealed) not less than 0.90 mm dia or securing with clips.

Mild steel TMT bars 10mm dia & over as in handle of manhole cover, cut to length, bent to shape required including cranking, bending spirally for hoping for columns, hooking ends binding with MS wire (annealed) not less than 0.90 mm dia or securing with clips.

M&L for mild steel TMT bars 5mm to 10mm dia as in stirrups, spacers & binders, cut to length, bend to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

Precast Cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in cover slab (for manholes etc) and similar articles with plain faces, set in cement mortar (1:4) with and including necessary form work.

S&F, 100mm size, SS Butt hinges, heavy weight, cold rolled mild steel, and fixed all as specified & directed by Engineer-in-charge.

S&F, 100mm size, butt hinges, medium weight, cold rolled mild steel including necessary welding if required all as specified & directed by Engineer-in-charge.

Form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc for rough finished flat surfaces all as specified & directed by Engineer-in-Charge.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) for rough finished flat surfaces all as specified & directed by Engineer-in-Charge.

M&L for reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified & directed directed by Engineer-in-charge.

M&L, reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintel over 1.50m spun complete all as specified & directed directed by Engineer-in-charge.

M&L for rendering 5 mm thick plaster in cement mortar (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth without using extra cement all as specified and directed by Engineer-in-charge.

M&L for applying evenly a priming/tack coat with bituminous primer at 0.4 ltr per sq metre for water proofing treatment all as specified and directed by Engineer-in-charge.

S&F in repair bib taps cast copper alloy with crutch or butter fly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

S&F 32 mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified & directed by Engineer-in-charge.

S&F, urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified & directed by Engineer-in-charge.

S & F Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union

S & F, 35 mm thick second class hard wood factory made plain, framed, panelled shutters, with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and Style as per IS:1003 (Part-1), kiln seasoned and chemically pressure treated all as specified & directed by Engineer-in-charge.

S&F, rolled mild steel framed work as in doors or gates of angle or other section confirming to Fe 410-W (Gde E-250 quality-A) with gusset plates, rails braces, etc., complete, drilled for fixing of steel sheeting or other covering door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door, fittings and hanging, also fastering and fixing complete all as specified & directed.

M&L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified & directed by Engineer-in-charge.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified & directed by Engineer-in-charge.

S&F stop cock, fancy type, chromium plated, with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15 mm bore iron pipe or for union complete all as specified & directed by Engineer-in-charge.

S&F 140mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified & directed by Engineer-in-charge.

S&F 32mm High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc complete all as specified & directed by Engineer-in-charge.

S&F, tubular towel rail aluminium anodised, 20mm dia, D type, 60cm long between flanges fixed with chromium plated brass screws complete all as specified & directed by Engineer-in-charge.

M&L 100 mm size cast iron floor, trap, with grating including jointing to waste pipe fixed in cement conrete (1:2:4) type B-1 complete all as specified & directed by Engineer-in-charge.

S&F 3mm thick frosted glass and glazing with oil putty in square not exceeding 0.5 sqm in each pane all as specified and directed.

M & L for plastering in CM 1:6 , 15 mm thick on internal face of wall finished even and smooth without using extra cement complete all as specified and directed.

M& L for preparing of newly plastered surfaces of wall and applying two coats of cement base paint on walls including in narrow width, bands, cornices, pilasters etc and cracked filled with putty/cement motar and match the existing surface complete all as specified and as directed (Note:camouflage pattern as per approved by GE ).

M&L for non skid ceramic coloured tiles of size 300x 300 by 7mm thick joint free grade B-II (a) superior quality confirming to IS 13755 as in floors set & jointed in neat cement slurry and pointed in coloured cement to match the tiles and including scread bed or bedding layer 15mm thick in CM 1:4 all as specified.

M&L for PCC 1:2:4, 50mm thick using 20mm graded aggregate as in flooring

M&L glazed colour ceramic tiles(joint less) in of size 350 x 250x 7mm /450X350X7mm thick as in dado including all round border tiles pattern and print as approved and width of border tiles not less then 75mm including screed bed or bedding layer 10mm thick in CM 1:4 all as specified.

S&F PVC waste pipe 40mm dia 600mm long complete all as specified and directed.

S & F brass chromium plated concealed Angular stop cock with flange for 15mm bore GI tubing complete all as specified and directed.

S&FCP brass soap dish fancy type complete all as specified and directed.

S & F Brass Chromium plated tubular towel rail, 20 mm dia, D Type, 60 cm long between flanges complete all as specified and directed.

S & F Rototional mould ed polythylene water storage tanks white 500 ltr (cylidrical verticial with closed top) hoisted and fixed in postion including float valve high pressure epoxy coated aluminium rod & plastic ball 20 mm dia complete.

S&F Pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet/ semi corrugated 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws as specified.

S & F Joist, channel,angel or tee sections, fixed independently , without connecting plates etc Fe 410w(Grade E-250 quality B)

S& F for anodised aluminium frame for doors, windows, ventilators and partition in room with one or more rebates including joining cleat forfixing etc. complete all as specified

M&L for Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S&F for 6 mm Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work as specified in each pane complete all as specified.

S&F for Brass Mortice lock, vertical type, size 65 mm 4 lever

S&F Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed

M&L, 20mm bore pipe galvanised iron, medium grade (ISI marked) complete with fittings (ISI Marked) laid in trenches, jointed and tested complete all as specified and directed of following bore

M&L, 25mm bore pipe galvanised iron, medium grade (ISI marked) complete with fittings (ISI Marked) laid in trenches, jointed and tested complete all as specified and directed of following bore

M&L, 40mm bore pipe galvanised iron, medium grade (ISI marked) complete with fittings (ISI Marked) laid in trenches, jointed and tested complete all as specified and directed of following bore

M&L, 50mm bore pipe galvanised iron, medium grade (ISI marked) complete with fittings (ISI Marked) laid in trenches, jointed and tested complete all as specified and directed of following bore

M & L for cutting existing GI tubing for alteration or additions of sizes including screwing existing GI tubing for tapping & making new connections etc of 20 mm bore complete all as specified & directed by Engr-in-Charge.

M & L for cutting existing GI tubing for alteration or additions of sizes including screwing existing GI tubing for tapping & making new connections etc of 50 mm bore complete all as specified & directed by Engr-in-Charge.

M&L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straigth or curved) complete all as specified & directed.

Supply & laying of XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) with aluminium conductor 1100 volts grade 10 Sqmm 2 Core complete all as specified and directed by Engineer-in-charge.

Supply & laying of XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) with aluminium conductor 1100 volts grade 25 Sqmm 4 Core complete all as specified and directed by Engineer-in-charge.

M&L for sand cushioning to underground PVC/XLPE cable with tibba sand and punning to provide required cover complete all as directed by Engineer-in-charge. (Note :- For the purpose of payment only punned thickness will be measured).

Supplying and laying Jodhpur stone quarry faced stone slab cover 25 to 30 cm in width, 50 to 60 cm long and 40 to 50 mm thick, laid dry and abutting each other with gap between adjacent slab not exceeding 10 mm over under ground cables for protection complete all as specified & directed by Engineer-in-charge.

Supply, lay, test connecting and commissioning underground cable LT 1100 volt grade heavy duty XLPE insulated with aluminum stranded conductor armoured complete laid in trenches/fixed to poles /drawn through pipes with suitable size cable glands criping type cable lugs etc all as specified and directed of size 6 Sqmm 2 core.

M&L for bore earthing not less than 250mm dia 16 feet deep filled with black soil upto 7 feet from bottom complete with galvanised iron pipe 40mm bore medium grade 3m long tapers at bottom & provided 12mm holes (staggered) at 75mm centre to centre upto 2.5m of length from bottom, burried directly in ground filled with 45cm alternate layer of magnisium sulphate, charcol & salt up to ground level & connected to galvanised iron strip 32x6mm above ground level as earthing lead by means of bolt and nut, check nuts and washers of galvanised iron or steel including brazing work upto equipment and 40mm dia light grade GI pipe for earth lead protection and testing on completion complete including taking out old earthing all as specified & directed by Engineer-in-charge.

M&L for road cutting and insert the pipe in road for safety of cable complete all as specified.

S&F 40 mm bore GI tubing "light grade" in trenaches on pole for protection of cables complete all as specified & directed by Engineer-in-Charge.

M & L for Point wiring using colour coding as per IS with 1.5 Sq mm multistranded copper conductor single core FRLS PVC insulated unsheathed 1100 Volts, ISI-694 marked drawn through and including heavy duty ISI marked PVC Concealed Conduit alongwith its accessories of suitable size, with GI sunken boxes of 1.2 mm thick, 60 mm depth of suitable size including fixing/ grouting sunken as per site requirement and making good to match with existing finishes including provision of cover with white colour hylum sheet of 3.6 mm thickness switches/ sockets/ regulators etc including running up of 1.5 Sq mm copper conductor FRLS, PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly all as specified for the following :

(a) One light point controlled by one, one way switch

(d) One three pin 5 Amps socket outlet point controlled by one No one way switch on same board

(c) One three pin 5 Amps socket outlet point controlled by one No one way switch on independant board

All as per Item No. 178.00 above but with stranded copper conductor 2.5 Sq. mm (nominal area), single core, PVC insulated and unsheathed multistranded FRLS cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated multistranded FRLS copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

S&F for Switch piano flush type single pole one way, and 6 amp complete ISI mark complete all as specified.

S&F for Socket outlet multipurpose having provision for 2 in 1, 3 pin 5 amp piano flush type complete all as specified

S & F for Switch piano flush type single pole one way, and 15 amp complete ISI marked complete all as specified.

S&F for socket outlet 2 in 1, 2/3 pin 5 Amps and 15 Amps flush type complete all as specified.

S & F for celling rose 2/3 terminals, PVC/ polycarbonate, isolated body ISI marked complete all as specified.

S & F for stepped type fan regulator, Socket type, operating on 230 Volt 50 Hz complete all as specified.

S & F for MCB DB SPN 4 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 230 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed .

S & F for MCB SPN double pole rated capacity 40 amps, 230 volts breaking capacity 10 KA complete all as specified and as directed.

S & F for MCB Single pole rated capacity 6 to 32 amps, 240 V breaking capacity 10 KA complete all as specified and as directed.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver complete all as specified and direced by Engineer-in-charge.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 450 mm sweep with louver complete all as specified and direced by Engineer-in-charge.

S&F for water heater storage type (Geyser) vertical type, inner container of capacity 50 ltrs, electrically operated, AC 230 Volts, including 04 Nos of old fashner nuts required suitable size fixed in brick wall complete all as specied and directed.

S & F for LED tube light fitting 20 Watt 4 Feet or 1183 MM in lenth, IP 20 Protection, wall mounted type, Slim LED Batten with polycarbonate housingand diffuser, elegant design with end caps, having excellent thermally managed polycarbonate extrution, LM 80 Certified LED having Integral Electronic Constant Current Driver , IP 20 Protection, Opreating voltage 240 V , 50Hz AC Supply and Operating tempraeture 0 to 50 C, Power factor ≥ 0.9, Lumen output ≥ 2000, necessary mounting arrangements on PVC Square box 2 Nos, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified Make Orient, Philips, Crompton, Havells etc

S & F for wall mounted LED 18 watts with out put of 1800 lumens , box type (decorative) light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 4' x 18 watts complete all as specified and as directed. Make :- Make Bajaj Cat part No BLRB-DB118 & BLRB 18W CWC or its equvalent in Philips, Wipro, Havells.

S & F for LED tube light fitting 10 Watt, 2 Feet or 591 MM in length, IP 20 Protection, wall mounted type, Slim LED Batten with polycarbonate housingand diffuser, elegant design with end caps, having excellent thermally managed polycarbonate extrution, LM 80 Certified LED having Integral Electronic Constant Current Driver, IP 20 Protection, Opreating voltage 240 V , 50Hz AC Supply and Operating tempraeture 0 to 50 C, Power factor ≥ 0.9, Lumen output ≥ 1000, necessary mounting arrangements on PVC Square box 2 Nos, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified Make Orient, Philips, Crompton, Havells etc

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 15 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade required dia 1.5 mtr long bend to required shape complete all as directed by Engineer-in-Charge. Make- havells Cat part No - LHEWEBP7PL6S025 or its equivalent in Wipro, BAJAJ, PhilipS

M&L for submain wiring with approved colour code/as per IS (Red, black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper coductor of nominal cross sectional area of 6.0 Sq mm (FRlS) in in and including PVC conduit and accessories non metallic including one run of PVC insulated multistranded copper conductor nominal cross section area of 6.0 Sq mm (FRLS) of continuous earth wire green in colour complete all as specified and directed by Engineer-in-charge. (NOTE: Two runs of 6.0 sqmm cable & One run of 6.0 sqmm cable and One run of PVC conduit shall be paid as one unit length.)

M & L for submain wiring with approved colour code/as per IS (Red,black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 6.00 Sqmm (FRLS) in PVC Cassing Capping conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 6.00 Sqmm (FRLS) of continous earth wire green in colour complete including taking down old unserviceble sub main wiring all as specified and directed by Engr-In-Charge.(Note :- Two runsof 6.00 Sqmm cable & one run of 6.00 Sqmm cable one run of PVC casing caping shall be paid as one unit length)

M/S MAYA CONSTRUCTION COMPANY