PROVN OF DEFICIENT GSE CENTRE AND BARBER SHOP AT SHIBPUR UNDER GE (SOUTH) DIGLIPUR

Amount

Surface dressing not exceeding 15 cm deep in soft/loose soil and getting out complete all as specified and directed

Surface excavation not exceeding 30cm deep and avg 15 cm getting out in any type of soil complete all as specified and directed

M & L for PCC (1:4:8), type D-2, using (40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M&L providing Cement Concrete in foundations, filling and mass concrete (1:3:6) type C2 (using 40 mm graded aggregate) complete all as specified and directed

M&L precast cement concrete (1:3:6) using (20mm graded stone aggregate) solid blocks masonry exceeding 10cm in width and set and jointed in Cement Mortar (1:4) complete all as specified and directed.

M&L for Plain cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) in coping, kneelers water throughs bed plates, kerbs and like including weathering, slightly rounded or chamfered engles and throating, finished even & smooth without using extra cement complete all as specified and directed

M&L for Extra for forming fair finished drain or channel 45cm inner girth in cement concrete using extra cement , including forms, moulds, mitred/stopped ends etc complete all as specified and directed

M&L RCC M-30 (Design Mix) (20mm graded agg)in fdn incl rafts, footings, foundation beams, plinth beams, bases for columns, etc; basement slabs, under reamed piles and mass concrete complete all as specified and directed

M&L RCC M-30 (Design Mix) (20mm graded agg) column, pillar post incl footing/plinth beam complete all as specified and directed

M&L RCC M-30 (Design Mix) (20mm graded agg) as in chajjas complete all as specified and directed

M&L RCC M-30 (Design Mix) (20mm graded agg) as in lintel and roof beams over 1.5m span complete all as specified and directed

M&L RCC M-30 (Design Mix) (20mm graded agg) slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M&L RCC (1:2:4) Type B1 (using 20mm graded agg) as in lintels beams etc complete all as specified and directed

Use and waste of form work to sides of concrete foundation, footing, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams and similar work rough finished surfaces of concrete complete all as specified and as directed.

Use and waste of form work to sides of pillars, post, struts and columns complete all as specified and directed

Use and waste of form work to sides and soffits of chajjas complete all as specified and directed

Use and waste of form work to sides and soffits of RCC beam, lintel bands complete all as specified and directed

Use and waste of form work to soffits of suspended slabs such as roof slabs complete all as specified and directed

S & F mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

S & F mild steel TMT bars, 5mm dia and over up to including 10mm dia in stirrups, cut to length, bent to shape required, including bending for columns, beams hooking ends and binding with & including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M & L for rendering 5mm thick on fair faces of brick work or concrete surfaces in CM (1:4) for ceiling complete all as specified and directed

M & L 15mm thick for rendering fair faces of brick work or Concrete surface 15mm thick CM (1:4) as finishing mixed with integral water proofing compound @ 2% by weight of cement finished even and smooth without using extra cement complete all as specified and as directed. (Note: Water proofing compund shall be measured and paied seperately)

Supply only integral water poofing compound (PIDIPROOF LW)

M & L for rendering 10mm thick plaster in CM (1:6) on other than fair faces of brick work or stone masonry surfaces complete all as specified and directed

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar in two layers 10mm thick in CM 1:4 followed by 5mm thick plaster in CM (1:4) complete all as specified and directed.

M & L for 75mm thick PCC 1:3:6 , type C-2 using (40mm graded stone aggregate) as in plinth protection finished even & smooth without using extra cement making 10mm wide joints at every 3m interval and at every corner, filled with hot mix of bitumen complete all as specified and directed

M & L for moorum filling in floors laid in lagers not exceeding 15cm thick spread levelled and rammed including Watering complete all as specified and directed

M & L for hardcore of gauge n exc 63mm diposited, spread and levelled in lagers n exc 15cm thick, watered and rammed to a true surface with broken stone complete all as specified and directed

M&L 100mm thick PCC (1:4:8) type D2 (40mm graded agg) as in sub flooring complete all as specified and directed

M&L for 75MM thick PCC (1:3:6), type C2 (using 40mm graded stone aggregate) as in sub floor complete all as specified.

M&L for 40mm thick PCC (1:2:4), type B1(using 20 mm graded stone aggregate) as in floor complete all as specified.

M&L for chequered cement concrete tiles with grey cement and pigment of size 300 x 300 x 25mm, set jointed and pointed in neat cement slurry over 15mm thick screed in CM (1:6) complete all as specified and directed

M&L three coats of white washing on ceiling including perpatation of plaslered surpaces complete all as specified and directed

M&L for three coats of white washing to new undecorated surfaces of wall including preparation of surfaces complete all as specified and directed

M&L two coats of cement base paint over a coat of primer and preparation of new surpaces complete all as specified and directed

M&L for preparation of newly plastered wall surface applying two coat of acrylic distemper on wall over a coat of primer on plastererd surfaces complete all as specified and directed

M&L 125mm thick PCC (1:2:4) type B2 (40mm graded aggregate) in floor finished even and smooth with using extra cement complete all as specified and directed

S&F glass dividing strips 3mm thick and inserted in position, 30 mm wide complete all as specified and directed

M&L for water proofing treatment of roof surfaces with 3 mm thick modified APP membrane weighing 3kg/sqm reinforced with polyster non wove fabric with one coat of bitumen primer @ 0.40 ltr/ sqm and one coat of bonding material using blown type bitymen confirming to IS-702 grade 85/25 @ 1.20 Kg/Sqm complete all as specified and directed

S&F steel rolling shutters of 1.25mm thick laths wth gear operated type with bevel gear box and crank handle as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated complete, push pull or manual type complete all as specified and directed

S&F anodised aluminium frame for doors, window ventilators, partations with one or more rebates including jointing cleat for fixing etc complete all as specified and directed..

S&F anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clip, rubber packing , anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 Nos), hinges type B-21 100mm long(2 Nos), suitable handle 1 Nos complete all as specified and directed

S&F anodised aluminium window and ventilator shutters, fixed type without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clip, rubber packing , anodised aluminium snap beading, screws, anodised aluminium fittings complete all as specified and directed

S&F 4.8mm thick sheet glass ordinary quality and glazing in squares not exceeding 0.50 sqm in each pane of aluminium door / window complete all as specified and directed

M&L for granite (of any type) tiles 20mm thick machine cut bedded and pointed with grey cement slurry and point with white cement with admixture of pigment to match the shade of granite stone incl grinding and polishing over 15mm th screed bed in CM (1:4) complete all as specified and directed

M & L for 75mm thick PCC 1:4:8 , type D-2 using (40mm graded stone aggregate) as in floors complete all as specified and directed

M&L Non-skid ceramic colour tiles 7 to 8 mm thick , (square/rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed.

M&L Glazed ceramic colour tiles of size 350 x 250 x 7mm/ 450x350x7mm thick in vertical wall etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:4 complete as specified and directed.

M&L Non-skid ceramic colour tiles 7 to 8 mm thick , (square/rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 10 mm thick back coat in cement sand mortar 1:4 complete all as specified and as directed.

M & L for 6mm thick Non Asbestos cement plain building boards in false ceiling, fixed with and including powder coated aluminium T section of size (25 mm x 25mm and 0.80 mm thick) in square pattern of gride sizes of (600 x 600 mm), the powder coated aluminium frame work shall be fixed to ceiling and hanged from the ceiling with the help of suspenders made out of suitable dia not less than 08 SWG gauge GI hook and GI wire/6mm rod of required sizes to maintain proper level etc. The aluminium frame work is supported on side wall with the use of aluminium powder coated L section of size (20 mm x 22 mm x 0.80mm ) angles etc complete as per direction of Engineer-in-Charge & manufatureres specification.

S & F vitreous china wash basin,white flat back , size 550x400mm with and including Waste fittings, brass, chromium plated for basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including pillar tap 15mm bore, cast copper alloy with capstan heads cromium plated, screwed down high pressure with long screwed shank and fly nuts 450 mm long PVC connection with two Nos. complete all as specified and directed

S&F Fancy type chromium plated angle cock, cast copper alloy, screwd down high pressure with crutch or butterfly handle screwed both ends for iron pipe for for unions and fixed complete all as specified and directed

S&F 32mm dia of waste coupling of PTMT(half or full threaded of minimum weight 45 gms in wash basins complete all as specified and directed

S&F Towel rail 600mm long of PTMT fixed with and including chromium plated brass scres and wooden / plastic cleats of minimum weight 190 gms.

Supply, fixing, Jointing and testing 15 mm bore galvanised mild steel water tubing 'medium grade' with and including all fittings, fixed to walls and ceiling or laid in floors including taking downcomplete all as specified and directed.

Supply, fixing, Jointing and testing 20 mm bore galvanised mild steel water tubing 'medium grade' with and including all fittings, fixed to walls and ceiling or laid in floors including taking downcomplete all as specified and directed.

S&F grating doom 125mm dia with waste hole of PTMT (min weight 40 gms) complete all as specified and directed

S&F Steel work in tubular trusses, Purlin,Post etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed

S&F plain/chequered plates channels FE 410-W(Gde 250 quality), square cut or notched forming holes without any attachment complete all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed

M&L for preparation of newl steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

S&F anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clip, rubber packing , handles 02 Nos for each door, hinges anodised aluminium snap beaning screws etc complete all as specified and directed

S&F Anodized aluminium grill (anodised tranparent or dyed to required shade according to IS:1868 with minimim anodic coating of grade AC 15) of approved design / pattern, with approved standard section and fixed to the existing window frame with CP brass / stainless steel screws "200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised alumium standard section around the opening complete all as specified and directed

S&F 12mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed

M&L RCC (1:2:4), Type B1 (using 20mm graded agg) as in coping, bed plates etc complete all as specified and directed

S&F Mild steel screw bolts of 11 to 15mm diameter of shank (machine made) with hexagonal or square heads at one end and screwed the other, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5 cm and not exceeding 10 cm long complete all as specified and directed

M&L for 25mm thick prelaminated particle board interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work complete all as specified and directed

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel bright finished complete all as specified and directed

S&F 75mm but hinges medium weight cold rolled mild steel complete all as specified and directed

S&F in repairs Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed

Excavation in trenches, not exceeding 1.5m wide and n.exc. 1.5m deep for foundation etc n.exc.10 Sqm on plan and getting out soft / loose soil complete all as specified and directed

Returning filling including spreading, levelling, watering and well ramming in layers not exc 25 cm soft/loose soil complete all as specified and directed

Removing excavated materials not exceeding 50 m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed

M&L for point wiring with 1.5 sqmm (nominal area) single core PVC insulated unshethed FRLS cable, multistranded, copper conductor, in universal color code with & iincluding suitable size of rigid non metallic PVC casing coping and its all accessories complete in wall/roof and including with modular metal box with sheet suaitable for mounting switches, socket,regulator etc and including earth wire of PVC insulated FRLS copper conductor multistranded of 1.5 Sqmm size in green color for one light/fan/bell point controlled by one switch complete all as specified and directed

(a) All as per item No.78 but one 3 pin 5/6 Amps socket point controlled by one switch on independent board.

(b) All as per item No.78 but one 3 pin 5/6 Amps socket point controlled by one switch on Same board.

(c) All as per item No.78 but One 3 pin socket outlet, 5/6 amps on the independent board with other switches, with cables 1.5sqmm

(d) All as per item No.78 but point wiring with 2.5 sqmm (nominal area) single core and earth wire of 2.5 Sqmm size in green color for one powre point controlled by one switch complete all as specified and as directed

(e) All as per item No.78 but point wiring with 4 sqmm (nominal area) single core and earth wire of 4 Sqmm size in green color for one powre point controlled by one switch complete all as specified and as directed

S&F switch moduler type,single pole one moduler 6 Amps 230 volts complete all as specified.

S&F socket moduler type, single pole two moduler 2-in-1, 5 pin, 6 Amps 230 Volt

S&F switch moduler type , single pole one moduler 16 Amps 230 volts complete all as specified.

S&F socket moduler type, 2-in-1, 5 pin, 6/16 Amps 2 moduler 230 volts complete all as specified.

Supply & fix switch socket 2 in 1 type (5 pin, 5/6 amps,white ivry finish flash type complete all as specified and directed.

Supply & fix switch socket 2 in 1 type (5 pin, 5/16 amps,white ivry finish flash type complete all as specified and directed.

S&F ceiling rose, bakelite, surface type 230/240 volts three terminal PVC/polycarbonate, isolated body complete all as specified and directed

S&F ceiling fans, complete with three blade, down rod, accessories 230 volts, 1200mm sweep, with squirrel cage induction motor complete all as specified and directed

S&F stepped type electronic fan regulator moduler type on the existing phenolic liminated sheet complete all as specified and directed

S&F sheet metal enclosure for DB's (double door type) when MCB 's to be used, single pole and neutral , 8 ways including blacking plate with 200 amp rated bus bar, 240 volts fixed sunk/flush to the wall complete all as specified and directed

Supply and fixing for sheet metal enclosures factory made powder coated MCB SPN 6 ways DB with bus bar 200 Amps, neutral link, earth bar, double door 230 volts etc complete all as specified and directed

Supply and fixing MCB SPN 32 amp rating 240V, 10KA, miniature circuit breaker (MCB) of following poles and current carrying capccity in the MCB DB complete all as specified and directed

Supply and fixing MCB SP 6 to 32 amp rating 240V, 10KA, miniature circuit breaker (MCB) of following poles and current carrying capccity in the MCB DB complete all as specified and directed

Supply and fixing LED light fitting 4 feet, 1X20 Watts , 220 volts, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

Supply and fixing LED light fitting 2 feet, 1X10 Watts , 220 volts, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

Supply and fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20A, 10 KA, C curve complete all as specified and directed

Supply and fix exhaust fan , steel body AC single phase, 230 volts of size 300mm sweep with blades, frame and louvers complete all as specified and directed.

Supplying, laying and testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 6.00 sqmm X 2 core complete all as specified and directed

S & F GI tubing medium grade of size 20 mm dia bore ISI marked fixing with wall, roof etc. complete with all accessories such as Tees Union, Bend, Elbow Niple reducer etc all as required at site for branch connection includinng cutting threading complete all as specified and directed

Supply & fix gun metal gate valve with iron wheel head, screwed both end for GI pipe and fixed of size 50 mm dia complete all as specified and directed

Supply and fixing gun metal gate valve with iron wheel head, scrwed boht end for GI pipe and fixed of size 20 mm dia complete all as specified and directed

M&L for masonry valve chamber internal size of 600x600x600mm with 200 mm thick solid concrete block masonary, block casted using PCC (1:4:8) type D-2, built in cement and sand mortar (1:6), 15 mm plaster to thick internal surface and external surface up to 15 cm below ground level and top of floor in CM (1:4) finished even and smooth without using extra cement 15 mm thick, MS sheet 3.15mm cover including 50x50x6 mm MS angle frame embedded in 150 mm thick PCC (1:2:4) type B-1, with 25x6 mm flat iron hold fast, handles, hinges with locking arrangments, applying one coat of red oxide primer and two coat of synthetic enamel paint to all steel surface including necessary excavation in any type of soil and disposal of surplus soil to a distance not to exceeding 50m complete all as specified and directed

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks four layer (cylindrical vertical with closed top) in white colur hoisted and fixed in position all as specified in SSR Part-I including one 20mm ball brass valve with polythene float and fly nut complete all as specified and directed.

Cutting the existing GI/CI pipi in position for insertion of new tee for branch connection of the size 40/50 mm dia complete all as specified and directed by Engr-in-Charge.

Suppl and laying XLPE insulated, armoured heavy duty electic cable with aliminium conductor, 1100 volts grade, cross-sectional area 16sqmm X 2.0 core all as specified and directed.

Supply and laying of DWC (double wall corrugatted) HDPE Pipe and including fittings such as couplers, bends , end caps etc, ISI marked of outer dia of 63 mm and inner dia 50mm , 6m length each, polyethylene with smooth internal and profiled external surface for non pressure under ground cable complete all as specified and directed

S & F GI tubing Light grade of size 50 mm dia bore ISI marked laying in trench complete with all accessories such as Tees Union,, Bend, Elbow Niple reducer etc for cable protection. all as required at site for includinng complete all as specified and directed by Engr-in-Charge.

Supply and Fixing LED Secuirty light fittings 60 watts 230 volts, AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver , lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed

Supply and fixing LED light fitting 1x35 watts , 220 volts, AC outdoor type with driver, high pressure die cast aluminium hosing and heat resistant complete with breacket connection up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing medium grade GI pipe 50mm dia for bracket of length not less then 1.2 mtr, bend to shape and fixed to pole/wall with two nos MS flat clamps etc complete duly painted with two coats of aluminium paint over a coat of zink coat primer complete all as specified and directed

Material & labour for Earthing complete with galvanized steel earth electrolde 60cmX60cmX6mm buried dirrectly in ground vertically not less than 2.25 mtr below ground level with top edge of earth plate at a depth not less than 1.5mtr below ground level connected to galvanized earth lead wire 4sqmm dia upto 7.5m long by means of bolts, nuts, check nuts and washer etc made of galvanized iron including 50 mm bore GI pipe medium grade up 7.5 m length all as shown on electrical plate No.3 of SSR Pt I and as specified and indicated and testing on completion including earth work and excavation in any type of soil, PCC chamber, RCC slab with cast iron frame, funnel with water pipe GI 20 mm medium grade, wire mesh and lugs complete all as specified and directed Note: (i) The unit rate shall be include for protection pipe, GI water pipe, wire mesh, funnel, excavation, RCC pit cover, PCC chamber pit, test point, galvanized earth wire 4 sqmm dia from top of earth plate up to 7.5meters above ground level and if GI protection pipe is less than 7.5 meters, no price adjustment shall be made. PCC pit shall be provided at least 500mm away from the earth pit and not just on the earth pit and extra cost of additional length of water pipes and fitting junction etc shall be deemed to be included in the unit rate. (iii) RCC pit thick reinforced with XPM (weighing not less than 4KG/Sqm in liew of cast iron cover.all as specified and directed.

ASHOK BISWAS (BID ID -3331079)

City Constructie Pvt Ltd (BID ID -3339734)

Binod Hawlader (BID ID -3340030)

SUMAN (BID ID -3338642)

KML CONSTRUCTION (BID ID -3338675)