Improvement and covering of open area from pre-coated GIP Sheet between the new building and old building at GLM Hospital/City SP Zone

Dismantling stone slab flooring laid in cement mortar including stacking of serviceble material and disposal of unservicble material within 50 mertes lead.

Earth work in excavation in by mechanical means (Hydraulic excavator) / manual means foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m: All kind of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size)derived from natural sources.

Centring and shuttering including strutting, propping etc. and removal of form for: Columns, Pillars, Piers, Abutments, Posts and Struts.

Structural steel work in single section fixed without connecting plate including cutting,hoisting,fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes.

Providing and fixing of precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm ± 5% total coated thickness (TCT), Zinc coating 120 gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws f size (5.5 x 55 mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/vertical or curved surfaces excluding the cost of purlins, rafters and trussed and including cutting to size and shape wherever required

Providing and fixing bolts including nuts and washers complete

Providing and fixing precoated galvanized steel sheet roofing accessories 0.5 mm ± 5% total thickness (TCT), Zinc coating 120 gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns empoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete: Flashing/Aprons (Upto 600 mm).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work upto plinth level: 1:5: 10 (1 cement: 5 coarse sand(zone-III): 10 graded stone aggregate 40 mm nominal size)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with gery cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with Base of cement mortar 1:4 (1 cement :4 coarse sand) : 25 mm thick

Painting with synthetic enamle paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Carriage of material by mechanical transport including loading, unloading and stacking complete; Lime, moorum, building rubbish, earth, manure or sludge and excaveted rock : Lime, moorum, building rubbish ;19 km lead