Loading…
Loading…
Tender Value
₹1.9 Cr
EMD Value
₹2.5 L
Closing Date
20 Mar 2026, 2:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
ELECTRICAL
13 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual. turnover of V/N crores or V crores whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB in GCC works April 22, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. Certificate in the prescribed format for verification / confirmation of the documents submitted for compliance of eligibility / qualifying criteria For further more details refer clause 10.1 and 10.2 of GCC April 2022 with correction slip issued up to date
(a)The tenderer must have successfully completed any of the following during last 7 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work each costing not less than the amount equal to 60% of advertised value of the tender Similar works defined as "Successful completion of works involving supply, installation, testing and commissioning of outdoor/indoor substation ( with or without supply of transformers/ substation equipment) of 11KV or above."
12 conditions · 2 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
I/We have read the various conditions attached/referred to in this tender document and agree to abide by the said conditions.
I/We hereby Confirm that the rates, rebates and/or other financial terms, if any, quoted by us in the relevant fields of the Financial Bid page will only be the ruling terms for deciding the inter-se ranking, and any such condition having financial repercussions, if quoted by us anywhere else including attached documents shall not be considered for deciding inter-se ranking.
The Tenderers are advised to visit the site of work in their own interest and acquaint themselves with the site conditions and expected quantum o f work and assess all the site specific difficulties to be experienced while executing the same and the rate shall be arrived duly considering all the facts above and quoted in the tender. Any representation at a later date specifying the site difficulties shall not be considered.
The tenderer shall go through the entire tender documents thoroughly and strictly adhere the instructions and directions given at different pages.
(i)For all the tenders having advertised cost of Rs. 10 lakh or above, the contractor shall have the option to take payment from Railways through a letter of credit (LC) arrangement. (ii)This option of taking payment through LC arrangement has to be exercised in IREPS (Indian Railway Electronic Procurement System - the e-application on which tenders are called by Railways) by the tenderer at the time of bidding itself, and the tenderer shall affirm having read over and agreed to the terms and conditions of the LC option.(iii)The option so exercised, shall be an integral part of the bidder's offer.(iv)The above option of taking payment through LC arrangement, once exercised by tenderer at the time of bidding, shall be final and no change shall be permitted, thereafter, during execution of contract.(v)In case tenderer opts for payment through LC, following shall be the procedure to deal release of payment through LC:(a)The LC shall be a sight LC.(b)The contractor shall select his Advising/Negotiating bank for LC. The incidental cost towards issue of LC and its operation thereof shall be borne by the contractor.(c)SBI, New Delhi, Main Branch will be the nodal branch for issue of LCs based on online requests received from Railway Accounts Units for tenders opened in financial year 2018-19. SBI branches where the respective Railway Accounts Office has its Account (local SBI branch) will be the issuance/reimbursing branch for LC issued under this arrangement. The Bank shall remain same for this tender till completion of contract. The incidental cost @ 0.15 % per annum of LC value, towards issue of LC and operation thereof shall be borne by the contractor and shall be recovered from his bills. (d)The LC shall be opened initially for duration of 180 to 365 days in consultation with contractor. The LC shall be extended time to time as per the progress of the contract, on the request of the contractor. The value of LC to be opened initially as well as extended thereafter shall be finalised by the engineer in consultation with the contractor on the basis of expected progress of work.(e)The LC terms and conditions shall inter-alia indemnify and save harmless the Railway from and against all losses, claims and demands of every nature and description brought or recovered against the Railways by reason of any act or omission of the contractor, his agents or employees, in relation to the Letter of Credit (LC). All sums payable/borne by Railways on this account shall be considered as reasonable compensation and paid by Contractor.
(f)The LC terms and conditions shall inter-alia provide that Railways will issue a Document of Authorisation after passing the bill for completed work, to enable contractor to claim the authorized amount from their bank.(g)The acceptable, agreed upon document for payments to be released under the LC shall be the Document of Authorisation.(h)The Document of Authorisation shall be issued by Railway Accounts Office against each bill passed by Railways.(i)On issuance of Document of Authorisation, a copy of Document of Authorisation shall be posted on IREPS for download by the contractor. A digitally signed copy of Document of Authorisation shall also be sent by Railway Accounts Office to Railway's bank (Local SBI Branch). (j)The contractor shall take print out of the Document of Authorisation available on IREPS and present his claim to his bank (advising Bank) for necessary payments as per LC terms and conditions. The claim shall comprise of copy of Document of Authorisation, Bill of Exchange and Bill.(k)The payment against LC shall be subject to verification from Railway's Bank (Local SBI Branch). (l)The contractor's bank (advising bank) shall submit the documents to the Railways Bank (Local SBI Branch0.(m)The Railway's bank (issuing bank) shall, after verifying the claim so received w.r.t. the digitally signed Document of Authorisation received from Railway Accounts Office, release the payment to contractor's bank (advising bank) for crediting the same to contractor's account.(n)Any number of bills can be dealt within one LC, provided the sum total of payments to contractor is within the amount for which LC has been opened.(o)The LC shall be closed after the release of final payment including PVC amount, if any, to the contractor.(p)The release of performance guarantee or security deposit shall be dealt directly by Railway with the contractor i.e., not through LC.
MDU Division:- TEN: Augmentation of covered sick line shed and allied facilities for Coach maintenance - Electrical power supply and Lighting arrangements.
U-E-OT-2026-02-01
U-E-OT-2026-02-01
Open
Works - General
6 Months
Madurai, Tamil Nadu
₹0
₹2.5 L
20 Mar 2026
20 Feb 2026
2 Mar 2026
230 items across 5 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 9,20,101.44 | ||
| — | 66.00 | — | — | ||
| Supply of fabricated pole /strut from Rolled mild steel Joist (RSJ) of size200x100mm x5.7 mm as per specification | — | — | — | 1,32,000 | |
| — | 1.00 | — | — | ||
| Erection of four pole structure with 3m center spacing including channel, cross arms as per instruction of site Engineer incharge. | — | — | — | 40,000 | |
| — | 6.00 | — | — | ||
| Erection of RSJ pole of up to and including 30/36 feet height. Note : Supply of RSJ iscovered under different item of schedule. | — | — | — | 20,640 | |
| — | 26.00 | — | — | ||
| Fabrication, supply and fixing of MS Channels of the size 100X50X4.0 mm including fixing clamps, required accessories and fastners . painting with two coats of primer zinc chromate and Aluminum paints. | — | — | — | 24,700 | |
| — | 65.00 | — | — | ||
| Fabrication, supply and fixing of MS Channels of size 75X40X3.7mm including fixing clamps, required accessories and fastners . painting with two coats of primer zinc chromate and Aluminum paints. | — | — | — | 48,750 | |
| — | 42.00 | — | — | ||
| Fabrication, supply and fixing of MS Channels of size 40X40X4.0mm including fixing clamps, required accessories and fastners . painting with two coats of primer zinc chromate and Aluminum paints. | — | — | — | 6,508.74 | |
| — | 200.00 | — | — | ||
| Supply and fixing of 4 SWG GI wire for earth continunity | — | — | — | 3,406 | |
| — | 4.00 | — | — | ||
| Supply and fixing of Danger Board suitable for 11 KV / 22 KV/ 33 KV systems, as per IS. No:2551 and of 300mm X 200 mm(10" X 8") size. This shall be fixed with one number of clamps made out of MS flat of 25 mm X 4 mm size including bolts & nuts forfixing on structures painted with two coats in each of primer zinc chromate and aluminum paints.The danger board should be trilingual viz. Hindi, En glish and Tamil | — | — | — | 2,200 | |
| — | 4.00 | — | — | ||
| Fabrication, supply and fixing of Anti climbing Device as per the sample supplied by Railway. The flats should be made out of MS Flats of 40mm X 4mm in size and painted with two coats in each of primer zinc chromate and Aluminium paints. Bolts with nuts and washers to be used for fixing. and sharped 10mm dia MS rods of adequate length as instructed by Engineer-in-charge at site. | — | — | — | 2,936 | |
| — | 12.00 | — | — | ||
| Supply and fixing of 'B' class GI pipes for cable leading /protection of the 150 mm sizes including one number of clamps made out of MS flat of 40mm x6mm size, one per meter length including applying of end sealing compound on top etc. The GI pipe shall conform to is. 1239. | — | — | — | 16,696.2 | |
| — | 6.00 | — | — | ||
| Supply, erection and testing of HT earthing arrangements duly stenciling of earth resistance value along with date as per drawing number CEE/CN/MS/37-2004 with all accessories and copper plate of sizes including supply and spreading of 10 kgs in each salt and charcoal for earth treatment in an approved manner as directed by Engineer incharge at site. | — | — | — | 98,400 | |
| — | 3.00 | — | — | ||
| Supply, erection, testing and commissioning of GOABS, Triple Pole, Air Break, Outdoor, vertical tilting type, suitable to work on AC, 3 phase, 11 KV, 50 Hz | — | — | — | 36,000 | |
| — | 1.00 | — | — | ||
| Supply, fixing and testing of non-linear resistance, distribution type lightening arrester, suitable t owork on AC, three phase, 11 KV, 50Hz system (Note: one set comprises of 3 Nos) | — | — | — | 5,000 | |
| — | 6.00 | — | — | ||
| Supply, erection, testing and commissioning of 11 KV Polymer Disc Insulator with metals parts, fixing accessories, fastners complete in the existing cross arm / channel. | — | — | — | 7,200 | |
| — | 6.00 | — | — | ||
| Supply, erection, testing and commissioning of 11 KV Polymer PIN Insulator with metals parts, fixing accessories, fastners complete in the existing cross arm / channel. | — | — | — | 1,680 | |
| — | 60.00 | — | — | ||
| Excavation of trench and refilling in all kinds of soil as per specifications and drawing enclosed. | — | — | — | 26,880 | |
| — | 150.00 | — | — | ||
| Drawing of 11 KV, 185 sq mm cable in existing laid HDPE pipe | — | — | — | 6,642 | |
| — | 150.00 | — | — | ||
| Laying of 140 mm dia HDPE Pipe with required couplers/ joint complete. | — | — | — | 6,000 | |
| — | 6.00 | — | — | ||
| Supply and fixing of 11 KV end termination kit | — | — | — | 45,000 | |
| — | 10.00 | — | — | ||
| Supply and fixing of RCC Slab type HT cable route Indicator | — | — | — | 13,000 | |
| — | 1.00 | — | — | ||
| Preparation of detailed drawing for erected substation | — | — | — | 851.5 | |
| — | 25.00 | — | — | ||
| Fabrication, supply and fixing of clamps made out MS flats for fabrication of clamp for fixing of cover for existing power cable / enclosures made out of sheet metal given in this schedule etc. This shall be made out of MS flat of suitable size, powder coated of suitable colour as instructed by the engineer in charge and using GI bolts with nuts of suitable size for fixing.Note: This shall be made use for fixing of cover for existing power cable and new enclosures other than enclosures already covered in the schedule. | — | — | — | 3,425 | |
| — | 4.00 | — | — | ||
| Supply, erection, testing and commissioning of Drop out fuse assembly , AC, 11 kV, three phase, 50Hz supply, 200 Amps, in the existing double pole structure as per the instruction of Engineer incharge, | — | — | — | 22,000 | |
| — | 100.00 | — | — | ||
| Fabrication ,galvanization and supply of small part Galvanized steel sections including angles and channel bolts etc. | — | — | — | 15,000 | |
| — | 120.00 | — | — | ||
| Supply and erection of fencing to a height of 1.8mtrs above groundlevel and a retaining brick wall all around the height of 1 feet above ground leveling including supply of GI vertical members of 75x40x6mm MS channels at 1.5mtrs interval and tie angle at top with 25x25x6mm MS angle with frame and three inches weld mesh coated with aluminum paint and fence earth. | — | — | — | 2,52,000 | |
| — | 1.00 | — | — | ||
| — | 40.00 | — | — | ||
| — | 2.00 | — | — | ||
| — | 40.00 | — | — |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TenderDocumentforUploading.pdf Tender Document
ATTACHMENT
Correctionslipno1.pdf
ATTACHMENT
Correctionslipno2.pdf
ATTACHMENT
Correctionslipno3.pdf
ATTACHMENT
Correctionslipno4.pdf
ATTACHMENT
Correctionslipno5.pdf
ATTACHMENT
GCC_April-2022.pdf
ATTACHMENT
TenderDocumentforUploading.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .