WS-04/2021-22

Amount

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 Sqm on plan and not exc 1.5 mtr in depth and getting out in any type of soil, complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:4:8, type D-2 (using 40mm graded crushed stone aggregates) as in foundation, filling in and mass concrete etc., complete all as specified and directed by Engineer-in-Charge.

M&L for RCC (Nominal Mix), type A-1, 1:1.5:3 (using 20mm graded crushed stone aggregates) as in foundations includings rafts, footings, foundation beams, plinth beams, bases for columns etc. basement slabs, under-reamed piles and mass concrete, complete all as specified and directed by Engineer-in-Charge.

M&L for RCC (Nominal Mix), type A-1, 1:1.5:3 (using 20mm graded crushed stone aggregates) as in columns, pillars, piers, posts and struts, complete all as specified and directed by Engineer-in-Charge.

M&L for formwork to rough finished sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beam and similar work vertical or to batter, complete all as specified and directed by Engineer-in-Charge.

M&L for formwork to rough finished sides of pillars, posts, struts, piers, columns and stanchions, complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 7.00 above but 5mm dia and over upto 10mm dia as in strirrups, spacers and binders etc.

M&L for cement concerte 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in benching, bed plates, copings and the like including necessary formwork and finishing all exposed surfaces, complete all as specified and directed by Engineer-in-Charge.

M&L for rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc. complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (excluding steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, complete all as specified and directed by Engineer-in-Charge.

M&L for granite work with 20mm thick slab (of any type), table rubbed and polished, as in cooking platforms, flooring, vertical surface, steps and the like, set in neat cement slurry and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, laid over and including 15mm thick screed bed or bedding layer or plastered in CM 1:4, complete all as specified and directed by Engineer-in-Charge.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25cm thick, complete all as specified and directed by Engineer-in-Charge.

Removing excavated material not exc 50 mtr and depositing where directed at a level not exc 1.50 mtr above ground level, complete all as specified and directed by Engineer-in-Charge.

M&L for walling of random rubble stone masonary, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 and pointed flush the surface in contact with earth in the same mortor as the work proceeds including necessary weep holes at 2 metre centre to centre (staggered) as in retaining wall, complete all as specified and directed by Engineer-in-Charge.

M&L for raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortor in 1:4, complete all as specified and directed by Engineer-in-Charge.

S&F 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints as in weep holes / laid in trenches / floor, complete all as specified and directed by Engineer-in-Charge.

M&L for single gravel to hand packing (any thickness) at back of walls over arches etc. and raising (or lowering) to the required level, complete all as specified and directed by Engineer-in-Charge.

M&L for formwork to fair finished surfaces to edges of concrete slabs, shelves, treads, breaks in floors, window cills and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but not exc 10cm wide, complete all as specified and directed by Engineer-in-Charge.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil, complete all as specified and directed by Engineer-in-Charge.

M&L for broken stone or boulders hardcore of gauge not exc 63mm, deposited, spread and levelled in layers not exc. 15cm thick, watered and rammed to a true surface, complete all as specified and directed by Engineer-in-Charge.

M&L for forming 12mm thick expansion joints filled with preformed bituminous filler and top 30mm primed and sealed with sealing compound Grade ‘A’, complete all as specified and directed by Engineer-in-Charge.

M&L 100mm thick plain cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregates), as in sub base or floor etc., complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:3:6, type C-2 (using 40mm graded crushed stone aggregates) as in foundation, filling in and mass concrete etc., complete all as specified and directed by Engineer-in-Charge.

M&L for chequered cement concrete tiles of size 200mm x 200mm x 25mm thick, set, jointed and pointed in neat cement slurry with white cement and pigment as in treads / floor etc. over and including 20mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring for one light point / fan point, controlled by one switch SP 230 volts with 1.5 Sqmm copper conductor cable (multistranded) PVC insulated FRLS, unsheathed, surface type, drawing in and including PVC casing & caping or PVC conduit 19mm dia, ISI Marked having wall thickness not less than 2mm with sunk cast iron/pressed steel terminal boxes, made out of 1.2mm thick sheet including one coat red oxide primer on internal and external surface covered with 3mm thick hylam brand IS-2036 Marked laminated sheet cover (for mounting switches, sockets, regulators etc.) including 1.5 Sqmm PVC insulated (multistranded) FRLS unsheathed copper conductor earth wire, complete all as specified and directed by Engineer-in-Charge. Make of wire :- Havells / KEI / HPL / Polycab

S&F switch piano, flush type, single pole, one way, 5 Amps, complete all as specified and directed. Make :- Anchor / Cona / Standard / SSK

S&F sheet metal enclosure double door for mounting MCBs with 200 Amps rated busbar 4 way AC 240 volts with IP-43 protection including cutting chases to wall for fixing DB and making good the disturbed surface to match with existing surface, complete all as specified and directed by Engineer-in-Charge. Make :- Indoasian / Havells / Standard

S&F MCB SPN 40 Amps, 240 Volts, 50 Hz, AC, made from moulded self-extinguishing thermostate plastic and suitable for ‘C’ curve, 10 KA breaking capacity, complete all as specified and directed. Make :- Indoasian / Havells / Standard

S&F MCB SP 6-32 Amps, 240 Volts, 50 Hz, AC supply, suitable for ‘C’ curve, 10 KA breaking capacity, complete all as specified and directed. Make :- Indoasian / Havells / Standard

S&F 4.0 Sqmm 1100 volts grade heavy duty cable PVC insulated multistranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular, complete all as specified and directed by Engineer-in-Charge.

S&F 60 Watts LED decorative post top for 360 degree direct light with IP-65 protection light fitting and including suitable bracket and nuts, bolts etc., complete all as specified and directed by Engineer-in-Charge. Make :- Crompton Cat Part No. 60CDL/M or technocommercially equivalent make in HPL / Wipro / Halonix / Philips

M/S DFA Enterprises

RISING SUN ENGG WORKS