REPAIRS TO CEILING RAILING FLOOR HARDSTANDING FOOTPATH, RETAINING WALL FENCING GATES MISC BR WORK IN VOLNA TOWER PEER BABA AND OTHER HILLY AREA AND PERIODICAL SERVICES TO TECHNICAL BUILDING AT TUNIR AREA UNDER AGE BR II AT NAVAL STATION KARANJA

Amount

Notes : (i) The work consists of 02 jobs as under:- JOB (A) : TPP 23-24 OF Ser No. 43 & JOB (B) : TPP 23-24 MAINT (ii) Please refer schedule 'A' notes before quoting the tender. (iii) Amount of Schedule of Credit shall be deducted off line by the department. ITEMS FOR JOB 'A'

Note:- The Unit Rate quoted in r/o Ser item No 1.02 to 2.09 are deemed to include for the following and nothing extra will be paid for these works: 1. Supplying, erecting and use of scaffolding upto required height (max 25 to 30m) or upto 8th floor height with necessary H-frames, pipes, couplers, buckles, bracing, top platform with support railing at top etc. at all levels of building including carriage of the materials to the location, erecting, fixing the scaffolding and dismembering the same after working and taking away the scaffolding materials etc. complete as per direction of Engineer-in-charge. 2. Supplying, erecting & use of temporary bamboo scaffolding around the building as required. The scaffolding is to be secured properly in position by bracings, ties clamps, etc. complete including providing and erecting working platform at all heights as required, including removal after completion of work all as per direction of Engineer-in-Charge.

Demolition of pre-cast concrete block masonry built in cement mortar including all quoins, arches, pillars etc. walling complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width in type B1 (1:2:4) using 20mm graded stone aggregate and setting in mortar (1:6) complete all as specified and as directed

Taking down cement plaster on brick walls or stone walls etc including raking out joint, hacking for key, scrubbing down with water etc including removing debries directed for a distance max upto 500m complete all as specified and directed.

M&L for ready mix plaster 15 mm thick on fair faces of stone or brick/concrete surfaces cement plaster in CM (1:4) , finished even and smooth without using extra cement, complete all as specfified and directed.

M&L for ready mix plaster 15mm thick on fair faces of brick work or concrete surfaces of walls in cement mortar 1:6 finished even and smooth (with out using extra cement) complete all as specified and directed.

Preparation of new or previously untreated plastered surfaces of walls and M&L for applying two coats of acrylic antifungal paint exterior grade paint plain in camouflage pattern over & including one coat of primer complete all as specified and as directed

Preparing new plastered surfaces of walls and M&L for applying two coats of oil bound distemper over & including a coat of chalk whitening primer over 3mm thick wall care putty on plastered surfaces complete all as specified and directed.

Preparation of old wall surfaces of any description & M&L for applying one coats of acrylic (antifungal) exterior grade paint on wall/roof complete all as specified and directed.

Prepration of old plastered / decorated surfaces of walls and M&L for applying one coat of oil bound distemper on plastered/decorated wall surfaces complete all as specified and directed.

Demolition of cement concrete in ground floor and paving ofany thickness below or above ground level un re-inforced complete all as specified and directed. .

M&L PCC 1:3:6, type C2 (using 40 mm graded stone aggregate) 75 mm thick as in plinth protection without using extra cement complete all as specified and directed.

Taking down chowkats or frames exc 1.5sqm but n.exc 4 sqm each but with shutter (without taking off shutter from the frame) complete all as specified and as directed

All as per BOQ Item No.1.13 above but n.exc 1.5 sqm complete all as specified and as directed

Taking down shutters of any description exc 1 Sqm but nexc 2 sqm complete all as specified and directed.

S&F IInd class hard wood plain solid, straight, chowkats and frames wrought framed rebated on the solid , rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

M&L for vitrified tiles in patches matching with existing tile 7 to 8mm thick (squar / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white/coloured cement to match over and including 10 mm thick screed bed in cement mortar in 1:4 complete all as specified and as directed

S&F 35mm thick second class hard wood, plain framed, panelled shutter (Two panel) of 9mm BWP comercial ply or 12mm veneered particle board with comercial veneering on both faces the size of rail land stile as per IS 1003 (Part-I) killn seasoned and chemically pressure treated complete all as specified and directed.

S&F solid PVC door frame of size 50mmx 47mm made out of 5mm wood grains printed PVC sheet reinforced with ms square tube and edges painted to match with printed sheet complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (styled) consisting of frame made out of MS tube for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ,C" channel having a PVC sheet strip of 20mm width stuck in side with solvent cement for styles and plain colour PVC sheet for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles and rails with suitable PVC sheet bedding and jointed together with solvent cement supplying and fixing in the frame at site complete all as specified and directed.

S&F extruded aluminium alloy handles fabricated type anodized 150 mm size complete all as specified and directed.

S&F mild steel work, Grade Fe-410-0 or Fe- 310-0, as in flat iron (for holdfast) complete all as specified and as directed.

M&L stainless steel Butt hinges medium weight, cold rolled and fixed 100 mm long complete all as specified and directed.

S&F 150mm long aluminium anodized barrel tower bolts of extruded sections complete all as specified and directed.

S&F 300mm long aluminium alloy, anodized sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet cost of extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

Preparation of new wooden surfaces over 10cm width or girth and M&L for applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for PCC 1:3:6, type C1 (using 20 mm graded stone aggregate) coping or filling for hold fast without using extra cement complete all as specified and directed.

S&F for aluminium door/window/ventilator/partition, made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame & necessary jointing cleats, glazing clips, powder coated aluminium snap beading,screws etc, complete and also including powder coated aluminium fittings such as stainless steel hinges, tower bolts, hooks & eyes, peg stays and handles, concealed star lock for aluminium window, Mortice lock vertical type size 100mm 04 lever for door, rubber beading suitable for fixing 4mm / 5mm thick glass in aluminium window / doors including connected items,with and making good to the disturbed portion with its original specifications incl taking down existing members/frame any position complete all as specified and directed.

Hacking out old broken glass ( any thickness, size, quality or description ) from wooden or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality black glass colour, white or any colour/ tinted like blackk etc as directed by Engr-in-Charge and glazing with oil putty in square exc 0.5 Sqm in each pane with glazing pins complete all as specified and as directed . Note:- Rubber beading paid and measured seprately.

S&F for rubber beading suitable for fixing 4mm / 5mm thick glass in aluminium window / doors etc complete all as specified and as directed.

S&F in repair aluminium anodized grill of design DG 104 pattern made out of 10mm dia rod Fixed with and including standard aluminium frame of F section of size 23.40mmx15.30mm &1.4mm thick all as per manufactures instructions complete all as specified and directed.

S&F aluminium alloy wire cloth, 0.45mm dia of wire and average width of aperture 1.40mm and fixed with aluminium staples as fixed in repairs complete all as specified and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with & including 15mm thick screed bed in CM (1:6) etc complete all as specified and directed.

Dismantling wall and ceiling boards or insulation boards, any thickness, any description, including cover fillets complete all as specified and directed.

S&F false ceiling with Armstrong XL 24 mm grid system of grid size 600x600mm with 14 mm thick ceiling board of RH-90 of Armstrong. Grid shall be suspended from ceiling using 4 mm dia pre straighten GI wire with 6 mm nylone rawl plug & screws at 1200 mm intervals complete all as specified and directed. (Note:- Item rate shall be include any height of Bldgs for scafolding as all arrangement.)

S&F in repairs 14mm thick ceiling board of size 600mm x 600mm of RH-90 of Armstrong false ceiling complete all as specified and directed. (Note:- Item rate shall be include any height of Bldgs for scafolding as all arrangement.)

S&F 8 to 10mm thick density regular edged eco friendly light weight calcium silicate smooth texture false ceiling tiles size 600x600mm even back surface aluminium foil, truly moisture resistance 90% including main T section of size (25mm x 25 mm, 19 gauge or 1mm thick) in square pattern of grid size of 600 x 600 mm. The aluminium frame work is supported from the ceiling with the help of GI wire/6 mm dia GI (upto 1200 mm length) adjusting and maintain for proper level to roof salbs by means of ceiling cleats made out of GE flat 40x3 mm sie 60mm long and expansion hold fasterners 12.5mm dia 40mm long complete etc. The aluminium frame work is supported on side wall with the use of aluminium 25 mm X 25 mm angles complete all as specified and directed.

S&F PVC False ceiling consisting of 600 mm x 600 mm, 8-10mm thick prelaminated self design including frame work made using aluminium T section of size (25mm x 25 mm, 19 gauge or 1mm thick) in square pattern of grid size of 600 x 600 mm. The aluminium frame work is supported from the ceiling with the help of GI wire/6 mm dia GI (upto 1200 mm length) adjusting and maintain for proper level to roof salbs by means of ceiling cleats made out of GE flat 40x3 mm sie 60mm long and expansion hold fasterners 12.5mm dia 40mm long complete etc. The aluminium frame work is supported on side wall with the use of aluminium 25 mm X 25 mm angles complete all as specified and directed. (Note:- Items rate shall be include upto 20.00 meter height of bldgs for scaffolding as all arrangement all as specified and directed by Engr-in-Charge.)

S&F in repair 8 to 10mm thick PVC false ceiling consisting of 600mm x 600mm prelaminated self design insert existing frame work without disterbing the other false ceiling and making good existing frame with complete all as specified and directed. (Note:- Items rate shall be include upto 20.00 meter height of bldgs for scaffolding as all arrangement all as specified and directed by Engr-in-Charge.)

S&F in repairs 40 mm thick bonded mineral wool blanket slab made out of from glass wool having density 24 kg/cum and fixed as per manufacturers instruction including both side of blanket slab covered with polythene based jute hession cloth complete all as specified and directed.

S&F in repairs 15mm bib taps, cast copper alloy with crutch or butterfly handle, screwed down , screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs 15mm stop valves, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed bothends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs Wash hand basin vitreous china (flat back) size 550 x 400 mm including brackets waste brass chromium plated with & including long screwed shanks and fly nuts 32 mm size and 32mm dia PVC waste pipe of suitable lengthcomplete all as specified and directed.

S&F in repairs vitreous china water closet (Squatting pan) “Orissa” pattern of size 580 x 440 mm white with integral foot rest and ‘P’ trap (excluding flushing cistern) but including PVC flush pipe and provision of lime concrete bedding complete all as specified and directed.

S&F in repair for 10 litre capacity PVC valveless syphonic action type flushing cistern high or low level (exclusive of brackets) white with inlet ball valve, float and handle inlcuidng brackets complete all as specified and directed.

S&F in repair Rotational moulded Polyethylene (HDPE) Water Storage Tank 1000 LITRE Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I, including tank nipple, union and Lowering of unserviceable Water Storage Tank with Float Valve of any description complete all as specified and directed

S&F in repair Rotational moulded Polyethylene (HDPE) Water Storage Tank 2000 LITRE Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I, including tank nipple, union and Lowering of unserviceable Water Storage Tank with Float Valve of any description complete all as specified and directed

S&F CPVC water tubing 16mm bore pipe, SDR 11 including provision of all fittings and connected completed in concealed and surface, along with primer & slovent cement for joint as per ASTM D 2564, pipe material shall be as per ASTM D 1785, fitting/ flanges shall be as per ASTM D2467, incl taking down old pipe line in concealed and surface all as specified and directed .

All as per Item No. 1.50 above but 20mm bore CPVC pipe, complete all as specified and as directed

S&F in repairs 15 mm dia steel tube medium grade galvanized with all fittings and fixed complete in wall, ceiling or laid in floor complete all as specified and directed.

S&F in repairs 20 mm dia steel tube medium grade galvanized with all fittings and fixed complete in wall, ceiling or laid in floor complete all as specified and directed.

S&F in repair roller blinds for window/door/ ventelator, blind system consist of a coated aluminum tube of 38-45mm diameter at header with provision of fabric clamping, the fabric is rolled up and down through a chain drive system with built in drive gear and an over run brake system. The side brackets are universal type suitable both for wall and ceiling mounting, bottom end of the fabric is rolled over an oval shape aluminium tube with provision to lock the fabric etc and powder coated aluminum bottom bar with caps on both ends, load capacity minimum 2Kg/ linear meter and fabrics are included not measured seprately. Installation as per manufacturer guideline and site condition Note:- 1. Fabrics is 100% Trevira CS Prosan Biological active fabric, based on silver ion technology, fabric is to be opaque, inherently antimicrobial, washable, flame retardant and closely woven surface treated tabrick are not acceptable, minimum weight of the fabric 270 gms/Sqm and width of fabric minimum 2.80 mtr or as per site requirement. 2. Surface treated fabrics are not acceptable. Fabric should be conform to ISO 20743:2013, ISO 18184: 2019, NFPA 701 and BS -5867 3. Pattern, design like zebra blinds, Roman blinds, collinear blinds, honeycomb blinds etc and anycolour of fabric is approved by Engr-in-Charge. Make:- Kelvin window blinds and Verolex or equv

All as per BOQ item No 1.54 above but double roller blinds system complete all as specified and directed

Demolition of stone/brick masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facings dressed stone work and pre cast concrete articles complete all as specified and directed.

M&L for walling of random or polygonal rubble, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

All as per BOQ item No. 1.57 above but except stone complete all as specified and directed. Note:- stone obtained from demolition shall be reused.

M&L for Brick work with sub class B bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified and directed.

All as per BOQ srl item No. 1.59 above but except bricks complete all as specified & directed. Note:- Serviceable bricks obatined from complete all as specified and directed demoltion shall be re-used after cleaning etc.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified of RR wall brought upto courses, maximum depression n.exc. 40mm in granite or trap stone complete all as specified and directed.

M&L for raised pointing to random or polygonal rubble masonry uncoursed or brought upto course in CM (1:4) complete all as specified and directed.

Preparation of new or previously untreated plastered surfaces of walls and M&L for applying two coats of colour wash complete all as specified and directed.

S&F double side writing informatory stainless steel reflective sign board size 4'x3' having with aluminium sheet base of 2 mm thickness having retro reflective tape base and font. Colour and matter of sign board will be furnished by Engr-in-Charge. The frame of sign board should be 2 " outer dia square Stailness steel pipe and having 2 legs of stainless steel square pipe 9' ling each of 2" outer dia square pipe the board should be grouted in PCC work of size 300x300x450 mm including taking down of existing complete all as specified and directed.

M&L for PCC type D2, 1:4:8 using (40mm graded stone aggregate) 100mm thick as in sub base complete all as specified and directed.

M&L for PCC (1:3:6) type C1 using 20mm graded stone aggregate in coping bed black etc including necessary form work complete all as specified and directed.

M&L for 100 mm thick Cement concrete type B2 1:2:4 using 40 mm graded stone aggregate) laid in alternate panel for floor, path and harstanding complete all as specified and directed.

S&F in repair Galvanized 2 stand Steel Barbed wire 2.00mm dia barbed with dia barbs at 75 mm spacing and straining and fixing to any type of stsnderd rails, straining bolts,including securing or tying at crossings with and provisuion of galvanised mild steel pins, etc incl taking down of existing barbed wire as directed (each line wire to be measured) complete all as specified and directed

Restriaining resecurig including making good staples or tighting of cross wire galvanised barbed wire in any dia of wire or any spacing complete all as specified and directed.

S&F 950/650/450 mm dia concertina coil reinforced punched(chrome razor or blade wire with barbed top of 0.5mm thick galvanised sheet and core wire of dia 2.5mm of high tensile steel wire incuding galvanised MS staples/ Clips for tying at crossing complete including taking down of existing concertina coil complete all as specified and directed.

Dismantling of mild steel work of any description not other wise provided of complete all as specified and directed.

S&F mild steel wall as in posts and struts in fencing angle including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing with mesh etc) including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 (Gde-E-165 quality-B.) Note:-Posts/struts of angle iron made to shape shall be welded to existing angle iron bracket of security wall, contractor shall make his own arrangement for welding for boundary wall by using gen sets or any alternative arrangement.

Taking down existing angle iron from wall/ fencing post embadded in PCC and refixing in the same opening/position or other position as directed complete all as specified and as directed

Dismantling fencing wire mesh, any type complete all as specified and directed.

S&F mild steel security chain link fencing 60mmx60mm with PVC coated mesh made out of 3mm dia MS wire and 1.00mm thick PVC coating throughout fixed to RCC post including binding wire complete all as specfied and directed.

Fixing only chain link fencing including line wires, any mesh, restraining, resecuring including making good or tighting any size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) any section including taking out embedded portion in concrete complete all as specified and directed.

S&F mild steel round bars 10mm dia and over, in horizontal support for chain link straining of fencing including cut to length, bent to shape required including cranking, bending spirally for hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-W (Gde E-250) complete all as specified and directed.

S&F mild steel screw bolts 10mm dia with hexagonal or square heads at one end and screwed at other ends dia of shank 5 to 10 mm and length of bolt exc. 5cm but n.exc 10cm complete all as specified and directed.

M&L PCC 1:2:4 type B2 using (40 mm graded stone aggregate) as in foundation, fillings and mass concrete complete all as specified and directed

S&F framed work such as grills, gratings, sun shed etc with ends of bars shouldered and/or riveted or welded, or forged into spikes, framed guard bars, barred iron doors, ladders, farmed balastures, walk ways, railings, frame work of water tanks and similar work conforming to Fe-410-0 or Fe-310-0 complete all as specified and directed.

Preparing new or previously untreated surface of any description, over 10cm in width or girth and M&L for applying two coats of synthetic enamel paint over & including one coat of red oxide primer complete all as specified and directed.

Dismantling plain or corrugated steel sheeting ,any gauge ,thickness incl Nainital or similar pattern roof covering complete all as specified and directed.

S&F 0.5 mm thick pre coated thick galvalume aluminium zink coated GI based corrougated steel sheeting or curved at end portion of any colour having tansile strength of 550 MPA and AZ-150 or above as in roof covering/glading to wall fixed with self tapping screws, complete all as specified and directed

S&F pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.5mm thick of an colour having tenstile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for joint free non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in CM (1:6) etc complete all as specified and directed.

M&L glazed coloured ceramic tiles in vertical surface 450x300x7mm thick as in skirting and dados, set and jointed in neat cement slurry and pointed in coloured cement to match over & including 10mm thick backing coat in CM 1:4 etc complete all as specified and directed

Dismantling of stone slabs & tiles of any description or thickness in floor aprons, cills etc laid bedded & pointed in any mortar complete all as specified and directed.

S&F green marble 18 to 20 mm thick machine cut, jointing and pointing with white cement slurry over & including 15mm thick screed bed or bedding layer of mortar in CM 1:6 complete all as specified and directed.

ITEMS FOR JOB 'B'

Preparation of old wall surfaces of any description and M&L for applying one coats of acrylic (antifungal) exterior grade paint white or coloured with the help of fully automatic airless spray machine flow speed of max 6 ltr per minutes with a maximum pressure 3300 PSI by the skilled labour on wall/ ceiling complete all as specified and directed.

Complete removal of existing treatment from wall by scrapping with mechanical wall sander (mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc including preparation of old decorated surfaces of walls, cornices, asbestos sheet and roof etc and M&L for applying (multipurpose mixer) wall care putty upto 2 mm thick and applying two coats of acrylic (antifungal) exterior grade paint white or coloured with the help of fully automatic airless spray machine flow speed of max 6 ltr per minutes with a maximum pressure 3300 PSI by the skilled labour over one coat of primer upto 4th storey including necessary scaffolding all as specified and directed Note:- 1. Work will be strictly executed by mechinised means/ tools as required for smart periodical services. 2. Allow 6-8 hrs to dry the surface for painting of subsequent coats complete all as specified and directed.

Preparation of old wall surfaces of any description and M&L for applying one coat of acrylic (antifungal) exterior grade paint of camouflage pattern complete all as specified and directed. (Note:- work will be strictly executed by mechinised means/ tools as required for smart periodical services).

Complete removal of existing treatment of walls and M&L for applying two coats of acrylic (antifungal) exterior grade paint of camouflage pattern over one coat of primer on wall/roof complete all as specified and directed . (Note:- work will be strictly executed by mechinised means/ tools as required for smart periodical services).

Complete removal of existing treatment from wall and ceiling by scrapping with mechanical wall sander (mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc including preparation of old decorated surfaces of walls, cornices, asbestos sheet as false ceiling and any description etc and M&L for applying (multipurpose mixer) wall care putty upto 2 mm thick and applying two coats of oil bound distemper white or coloured with the help of fully automatic airless spray machine flow speed of max 6 ltr per minutes with a maximum pressure 3300 PSI by the skilled labour over one coat of primer upto 4th storey including necessary scaffolding all as specified and directed . Note:- 1. Work will be strictly executed by mechinised means/ tools as required for smart periodical services. 2. Allow 6-8 hrs to dry the surface for painting of subsequent coats complete all as specified and directed.

Preparation of plastered or unplastered old decorated surfaces of wall and ceiling by all as specified and filling cracks/hole by applying walls and ceiling putty as required (multipurpose mixer) will be used for uniform and proper mixing of putty) and M&L for applying one coat of oil bounded distemper white or coloured with the help of fully automatic airless spray machine flow speed of max 6 ltr per minutes with a maximum pressure 3300 PSI by the skilled labour complete incl removal of nails etc and grinding where necessary all as specified & directed . (Note:- Item rate shall be include any height of Bldgs for scafolding as all arrangement.)

Complete removal of existing treatment by scrapping with mechanical wall sander (mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc including preparation of old decorated surfaces of walls, cornices, asbestos sheet and roof etc and M&L for applying (multipurpose mixer) wall care putty upto 2 mm thick and applying two coats royale luxury emulsion interior paint a luxurious smooth finish white or coloured over a coat of approved primer with the help of fully automatic airless spray machine flow speed of max 6 ltr per minutes with a maximum pressure 3300 PSI by the skilled labour over one coat of primer upto 4th storey including necessary scaffolding all as specified and directed . Note:- 1. Work will be strictly executed by mechinised means/ tools as required for smart periodical services. 2. Allow 6-8 hrs to dry the surface for painting of subsequent coats complete all as specified and directed.

M&L for two coats of smooth interior acrylic emulsion with Texture finish white or coloured having VOC less than 50 grams per ltr complying LEEDS criteria @1 ltrs(unndiluted) /10 sq mtrs diluted with water in 2:1 ratio applied over & including priming coat with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in both the coats of paint as per manufacturer instructions complete all as specified and directed.

Special Condition:- 1. The work pertaining to periodical services & Water Proofing shall be executed from authorized applicator through manufacturer of which the materials .i.e. Paint, Distemper, Cement base paint, Putty etc. is proposed to be used by the contractor and approved by Garrison Engineer. 2. Cleaning the floor surface area after painting work if contractor fail to cleaning the floor surface a recovery of Rs. 40/- per Sqm of floor area shall be made from his dues.

Shri Krishna Trading Corporation

M/s S.D Construction Co

K N CONSTRUCTION