PROVN OF KOTA STONE FLOORING OF GROUP I AND III STORE CSD DEPOT AND PROVN OF DISMANTABLE VIEW CUTTER SLIDING GATE AND OTHER CONNECTED WORKS AT FSH AND CERTAIN MINOR WORKS AT BB CANTT SRINAGAR

Amount

Demolition of plain cement concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) etc complete all specified and directed.

M&L for 40mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in sub base/levelling course finished rough to laying floor finishes complete all specified and directed.

M&L for Machine cut kota stone slab flooring 18-20mm thick laid over and including 20mm thick screed bed in CM 1:6, set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all specified and directed.

M&L for kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick backing coat in cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all specified and directed.

Taking down cement plaster of any description, on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as directed.

M&L for rendering 15mm thick in CM (1:6) on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8), Type D-2 (using 40mm graded crushed stone aggregates) as in sub base of floors/hard standing etc. complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, comlete all as specified and directed.

Excavation in post holes (or similar holes) each n. exc. 0.5 cum in soft/loose soil and getting out returning filling in and ramming earth or broken rubble mixed with eareth around in layers not exc. 25 cm watering and removing surplus soil to a distance n. exc 50 m and making good surface complete all as specified and directed.

M&L for PCC (1:3:6), type C-2 (using 40mm graded crushed stone aggregates) as in foundations, filling and mass concrete, complete all as specified and as directed.

M&L for brickwork with old size sub class 'B' bricks straight or curved on plan exc 6m mean radius and built in CM 1:6 complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces finished even and fair complete all as specified and directed.

M&L for rendering 10mm thick in CM (1:4) fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

S&F mild steel framed brackets of angles or tees with web and flanges, grill gates, tubular pipes or channel, roller for steel gate etc cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. n exc 10 kg each brackets, conforming to Fe-290 Gde-E-165, complete all as specified & directed

M&L for Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/cladding to wall fixed with self tapping screws, complete all as specified and directed.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers, in roof, wall etc with grade of zinc coating 275 complete all as specified and directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S & F stainless steel butt hinges 100mm size complete all as specified and directed.

S&F 150mm size extruded aluminium handles fabricated type, anodised all as specified and directed.

S & F 150 mm size aluminium anodised barrel tower bolts of extruded sections all as specified and directed.

S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

M&L for Vitrified Ceramic tiles 9-10 mm thick (square/ rectangular) light shade, polished, area of each tiles not exceeding 0.36sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick screed bed in CM 1:6, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) etc complete all specified and directed.

M&L for coloured glazed ceramic tiles on vertical surface as in dado, skirting etc of size 350x250x7mm/ 450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile fixed over and including 10mm thick backing coat in CM 1:4, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) etc complete all as specified and directed. Note:- The rates for disconnecting of all electric connection, taking down fittings and refixing the same and making connection after completion of work deemed to be included in quoted rates.

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick screed bed in CM 1:6, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) etc complete all specified and directed.

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick screed bed in CM 1:6, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) etc complete all specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes including necessary bends, fittings etc single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes including necessary bends, fittings etc single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 15mm bore steel water tubing medium grade galvanised with all fitting and fixed complete to wall and ceiling or laid in floors including taking up or down steel tubing and connections, including cleaning for refixing or removal from site complete all as specified and directed.

S&F 20mm bore steel water tubing medium grade galvanised with all fitting and fixed complete to wall and ceiling or laid in floors including taking up or down steel tubing and connections, including cleaning for refixing or removal from site complete all as specified and directed.

Lagging to pipes internal dia 15mm used in internal water supply or plumbing all round with 40mm thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144Kg/cum conforming to IS-9842 provided with and including chicken mesh wire netting 25 gauge, 20mm mesh and pop on top surface including removing old lagging complete all specified and directed.

Lagging to pipes internal dia 20mm used in internal water supply or plumbing all round with 40mm thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144Kg/cum conforming to IS-9842 provided with and including chicken mesh wire netting 25 gauge, 20mm mesh and pop on top surface including removing old lagging complete all specified and directed.

S&F 15mm bore Brass CP mixer (sink/WHB/wall) for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F 15mm bore Bib taps, chromium plated, fancy type, screwed down, screwed for iron pipe or for brass ferrule etc complete all as specified and directed.

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F 15mm bore stop valves or angle valve, fancy type chromium plated, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F 500 litres capacity rotational moulded polye-thylene water storage tanks three layers (cylindrical vertical with closed top) hoisted and fixed in position including brass float valve all as specified in SSR Part-I complete all as specified and directed.

M&L for chequered cement concrete tiles with grey cement and pigments 20cmx20cmx22-25mm thick, set, jointed and pointed in neat cement slurry in floors laid over and including 20mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for rubber moulded Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigment laid over and including sand cushioning as per site requirement complete all as specified and as directed.

M&L for 25mm thick PCC 1:2:4 type B-1 (using 12.5mm graded crushed stone aggregate) as in sub base/levelling course complete all specified and directed.

S & F vitreous China wash down (EWC) water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) but including plastic water closet seat cover closed pattern with flat bottom and cover with PVC hing devise, fixing bolt for pedestal pattern and PVC 'P' or 'S' trap complete all as specfied and directed.

S&F PVC valve less, syphonic action type low level flushing cistern, white with inlet ball valve, float handle, including brackets 10 ltr capacity including 32 mm PVC flush pipe complete all as specified and directed.

S&F vitreous china squatting pan ‘Orissa pattern’ size 580 x 440mm white with integral foot rest with ‘P’ or ‘S’ trap, (excluding flushing cistern and flush pipe) coneection to drai pipe etc complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F Brass chromium plated shower rose with or without swivel joints 125mm size fixed to steel pipe or union complete all as specified and directed.

S&F vitreous china wash hand basin, white, flat back of size 580x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, inclusive 32mm diawaste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and PVC waste pipe complete, all as specified and directed.

S&F brass chromium plated towel Rail 20mm dia including brackets complete all as specified and directed.

S&F vitreous china soap dish, white, approximate size 160x 160x90mm fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F Vitreous China Urinal, Half stall type, white including CP spray fittings & connections to flushing pipe and outgoing pipes complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of suitable primer complete all specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint complete all as specified and directed.

Excavation in trenches not exc 1.50 mtr wide and not exc 1.50 mtr in depth for foundation, shafts, cesspits, manholes, pier holes etc. not exc 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and as directed.

M&L for PCC 1:4:8, type D-2 (using 40mm graded crushed stone aggregates) as in foundations, filling and mass concrete, complete all as specified and as directed.

M&L for brickwork with old size sub class 'B' bricks straight or curved on plan exc 6m mean radius and built in CM 1:4 complete all as specified and directed.

M&L for rendering 10mm thick in CM (1:4) fair faces of brick work or concrete surfaces finished even and fair complete all as specified and directed.

M&L for rendering 10mm thick in CM (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for RCC (nominal mix) 1:1.5:3 type A-1 (using 20mm graded crushed stone aggregate) as in foundations,footings, foundation beams,plinth beams, bases for columns, etc, basement slabs, and mass concrete complete all as specified and directed.

M&L for RCC (nominal mix) 1:1.5:3 type A-1 (using 20mm graded crushed stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, manhole covers and in shelves and the like including use and waste formwork complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all specified and directed.

M&L for Mild steel TMT bars 5mm to 10mm dia, as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for flat rough finished surface complete all specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc 200mm thick (Horizontal or sloping) for rough finished surface complete all specified and directed.

Returning filling in including, spreading, leveling and well ramming in layers not exceeds 25 cm thick in any type of soil complete all as specified and directed.

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

Spreading, levelling, well ramming the earth filling under floor including watering as required in layers n exc. 25 cm thick complete all as specified and as directed.

M&L for hardcore of broken bricks guage n.exc 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

S&F structural steel work as in Roof trusses (framed), trussed, purlins crane gantries, rails & fastenings & heavy brackets framimg (Beam, tee, angle, channel or flat section) including distance pieces, cleats etc. Structural steel conforming to Fe-410W, Grade-E 250, Quality 'A' complete all as specified and as directed.

S&F rolled mild steel plates (plain or chequrred) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of grade FE-410W (Gde E 250 quality A ) complete all as specified and as directed.

S&F 2nd class softwood clean sawn 20mm thick boards or planks, width n exc. 25 cm as in eaves board, wall boarding etc complete all as specified and as directed.

M&L for IInd class hard wood, plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F 35mm thick, 2nd class H.W factory made panelled shutters (any number of panel) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified.

S&F steel ventilator with top hung shutters including hinges with steel handle and steel peg stay, complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in plinth protection/hard standing finished the surface even and smooth without using extra cement and making the joints with bitumastic filling in proporation of bitumen and sand 1:2 complete all as specified and directed.

S & F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinted tacks or galvanised wire staples or with wooden beading complete all as specified and directed

Taking down chowkats or frames with shutter exc 1.5 sqm but n exc 4.0 Sqm each (without taking off shutters from frames) and removing from site complete all as specified and directed.

S&F 35mm thick IInd class hard wood, glazed and skeleton shutter open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass/gauze etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed.

S&F mild steel butt hinges 100mm long medium weight colled rolled complete all as specified and directed.

S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F 300mm, Mild Steel ordinary rat tail rod pattern spring incl roller& roller plate & welding if necessary complete all as specified.

Dismantling wall and ceiling boards or insulation boards any thickness, any description including cover fillets complete all as specified and directed.

S&F 6mm thick ply wood grade BWR type BB, fixed with nails to timber frame work in ceiling flat or sloping complete all as specified and directed.

M&L for 6mm thick veneered decorative plywood, grade-1(with BWR resin) with decorative face veneers on one side face, fixed with screw or nails to timber frame work complete all as per specified and directed .

S&F 12mm thick gypsum board false ceiling including anodised aluminium snap grid frame for flase ceiling of size 600x600mm fixed with 4mm dia GI wire suspender one end tied to roof members and other end connected to main tee of grid frame work by means of 4mm dia adjustable 'J' hook consisting two nos washers and two nuts at 1.2m centre size of main Tee 36.5mmx25mmx1.40mm thick, cross tee section of size 23.5mmx26.4mmx1.40mm thick and supported at ends along the wall with aluminium anodised angle of size 40mmx25mmx2.0mm thick shall be fixed to wall with GI screw of 40mm long @ 450mm C/C along the perimeter of wall including applying two coats of distemper oil emulsion all as per manufacturer’s instruction complete all as specified and directed.

M&L for brick work with subclass 'B' bricks, straight or curved on plan any radius, built in cement mortar 1:4, in half brick thick wall complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes including necessary bends, fittings etc single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed.

S&F 15mm bore steel water tubing medium grade galvanised with all fitting and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore steel water tubing medium grade galvanised with all fitting and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Taking down carefully existing old burn out/unserviceable copper/aluminium point wiring any type (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing old materials tfrom site and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L for point wiring with PVC insulated FRLS wire, 1100 volt grade with multistranded copper conductor wire of size 1.5 Sqmm (Nominal area) drawn through surface on wall or concealed in wall with heavy duty ISI marked PVC conduit of suitable size 20mm dia or PVC casing capping of suitable size/ type along with its all connected fittings accessories including providing of pressed steel terminal sunken boxes 1.2mm thick dully fixed concealed in wall and covered with electro plated 3mm thick plastic laminated sheet for housing / mounting of switches, sockets, regulators etc and also using /drawind of 1.5 sqmm PVC insulated FRLS wire , 1100 Volt grade with multistranded copper conductor wire used as a continuous earth wire which is connected with terminated the box to ceing rose / fitting complete and including making good to all disturbed surfaces of wall/ceiling and floor area of wiring system and to match the existing surface of wall/floor/ceiling etc. all as specified and directed for following:-

One light/fan point controlled by one way switch 5 Amp

One 3/5 pin socket outlet, 5 Amps on same board

One 3/5 pin socket outlet, 5 Amps on independent board

All as per Sl item No.96 above but using single runs of PVC insulated FRLS wire, 1100volt grade with multistranded copper conductor wire of size 2.5 Sqmm (Nominal area) power point wiring system with controlled by one way switch fixed on independent board and also providing of 2.5 sqmm PVC insulated FRLS wire , 1100 Volt grade with multistranded copper conductor wire used as continuous earth wire complete all as specified and directed.

S&F switch piano, flush type, 5/6 Amps 230 Volts, one way complete as specified and directed.

S&F socket outlet two in one, 5/6 Amps 230 Volts, 3/5 pin type complete as specified and directed.

S&F switch piano, flush type, 15/16 Amps 230 Volts, one way complete as specified and directed.

S&F socket outlet two in one, 15/16 Amps 230 Volts, 5/6 multi pin type complete as specified and directed.

S&F ceiling rose three terminals type made out of polycarbonate, isolated body complete all as specified and directed.

S & F angular/batten type shape lamp holder with PVC/ Polycarbonate insulated body, alongwith brass adaptor and back plate for housing of bulb complete all as specified and directed.

S&F fan regulator with hum free step type alongwith speed control know of capacity 120 watt 230 Volts, complete all as specified and as directed.

S & F LED tube light fitting 1x 20/22W, 220V, AC decorative box type with driver, holder including LED tube light, energy efficient connecting up with three core flexiblecopper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp, energy efficient including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED luminaire 600mm x 600mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F surface mounted LED bulk head luminaries light fitting of rated capacity 10W out door type with dust and water proof, with PVC housing and unbreakable polycarbonate opal with inbuilt surge protection including providing of suitable type of flat flexible two/three core cable and making electric connection and including taking down of old fitting all as specified and directed.

S&F star rated electric ceiling fan 1200mm sweep min air delivery 210 CFM with service value 6.0 BEE norms 5 star rating with bruhless direct current motor (BLDC) of single phase 230 volt AC alongwith blade, down rod, canopy, clamps with reel insulator and MS fan hook fixed in ceiling/roof including providig flate flexible copper wire and making all electrical connection complete all as specified and directed.

S&F star rated ventilating exhaust fan made out of mild steel body complete with louvers and shutter, 300mm sweep, 230 Volts AC single phase, 50Hz, 1200 RPM, coper winding including making of suitable type /size of hole on any type of wall and fixing compete with nut, bolt etc and making good distrubed surface of wall/ceiling & finishes to match and providig flate flexible copper wire & making all electrical connection complete all as specified and directed.

S&F electric water heater storage type steel body with inner copper tank of storage capacity 25 ltr, BEE 5 star rating with heating element upto 2KW and providing all connecting accessories and electrical connection complete all as specified and directed.

S&F sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrangement system suitable of rating of size/type of distribution board SPN 12 way type 415 volt AC supply system with IP-43 protection rating and having neutral and earth link bus bar and mounting base channel suitable for holding MCBs incommer and outgoing system, fixed surface on wall or concealed in wall with the help of cutting chases to wall for fixing of DB and also making all necessary electrical connection and making good the disturbed wall surface complete all as specified and as directed.

S&F sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrangement system suitable of rating of size/type of distribution board SPN 8 way type 415 volt AC supply system and having neutral and earth link bus bar and mounting base channel suitable for holding MCBs incommer and outgoing system, fixed surface on wall or concealed in wall with the help of cutting chases to wall for fixing of DB and also making all necessary electrical connection and making good the disturbed wall surface complete all as specified and as directed.

S&F MCB SPN 40 to 63 Amps, 230 Volts, 50 Hz AC supply suitable for 'C' series, 10 KA breaking capacity complete all as specified and directed.

S&F MCB SP 6 to 32 Amps, 240 Volts, 50 Hz AC supply suitable for 'C' series, 10 KA breaking capacity complete all as specified and directed.

Supplying and fixing 1100 volts grade heavy duty twin core flat/ circular cable 16sqmm, PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by reel insulating hangers not more than 1 metre apart including 4mm suspension wire alongwith its all fittings and connected accessories, concealed in wall or surfaceon wall and making electric connection complete all as specified and directed.

M&L for earthing, complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (Earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 mtr below normal ground level connecting to the galvanised iron earth lead wire of 4mm dia by means of bolts, nuts, check nuts and washers of galavanised iron and earth strip protected by provision of GI light grade pipe 20 mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded of stone aggregate with XPM (weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and with 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate common salt and charcoal filling test point made out of 40mm/6mm flat iron with fixing arrangement funnel wire mesh and earth work in hard dense soil returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electrical plate No 03 of SSR-2009 Part-I and connecting to earth test point complete all as specified and directed.

S&F High galvanized mast light 15/16 mtr high, suitable for 9 lantern symmetrically fitted along with their control gear with electrically operated motor system and having two point suspension system with stainless steel wire rope of 6 mm dia 97/19 guage and double drum winch with luminaire mounting arm, pully assembly, aviation obstruction light, lightning arrester spike including necessary excavation and RCC foundation as per height complete all as specified and as directed. Note: Rates for necessary excavation & RCC foundation as per height & manufacturer's instructions are deemed to be included in quoted rates.

Supply, fixing/connecting LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant with driver and lamp complete all as specified and as directed.

Excavation in trenches/ under road/ PCC path/hard standing not exc. 1.5 m wide and n. exc. 1.5m depth for foundation, pole stays, laying of pipe / cable etc and getting out in hard /dense soil complete all as specified and directed.

M&L for dy sand cushioning for under ground cable provided with a layer of sand 8cm thick before laying cable and 15cm later of sand after laying and stretching the cable complete all as specified and directed. Note: Punned thickness of sand 18cm shall be measured and paid.

M&L for brick covering width equal to length of brick for protection to cable with well burnt sub class 'B' bricks laid dry flat complete all as specified and directed.

Supply, laying and testing of LT cable XLPE insulated, armoured electric power cable, heavy duty with aluminium conductor 1100 volt grade, cross sectional area 35 sqmm 3.5 core, laid in trenches, fixing on poles or passing through pipes etc complete all as specified and directed.

S&F street light pannel 3KW confirming to IS/IES 60947-4-1 suitable for 3 phase MCB rating 32 Amp on/off timer astronomical, contactor rating 32 amp including intrnal wiring in built short circuit protection, IP-54 complete all as specified and directed.

S&F Air termination, single pointed, aluminium rod 12mm dia and 300mm long complete all as specified and directed.

S&F Galvanised iron strip 32x6mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and directed.

S&F Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hexagonal head screw complete all as specified and directed.

S&F Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and directed.

M&L for earthing, complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (Earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 mtr below normal ground level connecting to the galvanised earth strip 32x6mm by means of bolts, nuts, check nuts and washers of galavanised iron and earth strip protected by provision of GI light grade pipe 20 mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded of stone aggregate with XPM (weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and with 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate common salt and charcoal filling test point made out of 40mm/6mm flat iron with fixing arrangement funnel wire mesh and earth work in hard dense soil returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electrical plate No 03 of SSR-2009 Part-I and connecting to earth test point complete all as specified and directed.

ZAHOOR ENGINEERING WORKS (BID ID -3087040)

M/S AKMAL CONSTRUCTIONS (BID ID -3094635)

M/S Vivek Gupta and Co (BID ID -3093536)