AN_2025

Amount

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire with painting of Suitable colour for Open PVC Light point / fan point etc. complete complying with standard specification and as directed by the departmental officers. (for electronic regulator) ( 5 points / Coil) Higher End.

Supply and fixing of 4' 20W LED Single box type fitting complete with TW round blocks on wall or ceiling with PVC unsheathed Copper leads from the terminals to the fittings with 1 No. 20 W LED tubes with inbuilt electronic driver etc. complete complying with standard specification and as directed by the departmental officers(Philips/Havells/Equivalent)

supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600 mm down rod with Provision of fan Hook etc. complete complying with standard specification and as directed by the departmental officers

Supply, Erection, Testing, Commissioning and Handing over of 1No 16 Persons Passenger Lift as per following technical specifications including all taxes and duties Technical Specifications: 1. Location:College of Engineering Guindy Chennai-25. 2. No of Lift: One Nos. 3. Type of Lift: Gearless with out Machine Room. 4. Capacity of Lift :16 Persons. (1088 Kgs) 5. Speed: 1.5 mtr / Sec 6. Type of Drive: Microprocessor based specific variable voltage variable frequency V3F with enhanced ride comfort and near zero leveling functions. VVVF Drive. 7. No of floor: Ground + 3 floors. 8. Total Travel: 16 mtrs approximate 9. Leveling Accuracy: High level accuracy with smooth & Jerk free stopping. 10. Construction of car: Special car made of Stainless Steel hairline finish No.4 hair line finish & panels with Direct lighting and New Beautiful Single Tile false ceiling with Tubular Handrail and mirror. 11. Position of Machine: Directly above the lift well shaft gearless. 12. No. of Landing Entrance: One in front - 4 Nos only. 13. No. of Car Entrance: One in front only. 14. Car Entrance Door: Centre opening automatic power door with stainless steel No.4 Hair Line finish with view panel operated centre opening SS cars. 15. Landing Entrance Door: Centre opening automatic power door with stainless steel No.4 Hair Line finish with view panel Power operated V3F Drive Centre opening stainless steel No.4 Hair line finish with view panel . door with provision for emergency key opening at all landing.

16. Car size: 2000mm widex 1300mm deepth (part 1) 17. Car clear Opening: 1000mm (wide) x 2000mm Height. (as per IS 14665 (Part-I)-2000). 18. Lift well : 2500mm(width)x2100mm (depth) 19. Lift pit depth 1600mm 20. Power supply : 415V,400/440v, 3 phase, 50 cy / Sec A.C supply for power and 230V, 50 Hz single phase AC supply for light. 21. Control: Micro processor Computer based - simplex collective full collective logic system with or without attendant mode. 22. Car fittings:Indirect fluorescent light & Fan. 23. Lift Well: RCC construction with Brick masonry 24. Induction: Up / Down Digital Direction scroll type and position indicator for all landing and in car. 25. Emergency Alarm Bell: Battery Operated Alarm Bell to be provided with automatic charging device. 26. Emergency Light: Battery operated Light to be provided with automatic charging device. 27. Fireman's switch: To be provided at ground floor. 28. Minor Builders Work: To be provided by lift contractor. 29. Scaffolding: To be provided by lift Contractor.

30. Stainless Steel still angles and facia Plates: To be provided by lift contractor. 31. Steel for lift Machinery: To be Provided by lift contractor. 32.Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by lift contractor during the guarntee period of one year 33. Provision of 1+3 EPABX intercom with phone to be provided at the following places 1. Lift Head Room 2. Reception Room and 3. Inside the Lift by lift contractor. 34.Lift License: Preparation of drawing , payment of charges to CEIG and insurance policy if any and obtaining CEIG safety certificate and lift license as per lift act should be done by the lift contractor. 35. Automatic rescue device: To facilitate the landing of the nearest floor at the time of power failure. This shall consist of suitable type battery system with charger inverter under voltage protection system etc. complete complying with standard specification and as directed by the departmental officers.(JOHNSON/OTIS/KONE) SR M-2369

Supply, Installation,Testing and commissioning of 22.5KVA three phase micro processor controller air cooled unbalanced electronic servo voltage stabilizer with high/low voltage cut-off and single phase preventor, with builtin manual bypass arrangements etc. complete complying with standard specification and as directed by the departmental officers

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point etc. complete complying with standard specification and as directed by the departmental officers(for electronic regulator) (6 points / Coil) Higher End.

Supply and fixing of WT bulk head fitting with guard suitable for 15W LED bulb with 15W LED bulbetc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End etc. complete complying with standard specification and as directed by the departmental officers.

Supply and run of 2 of 1.5sqmm (22/0.3)PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in rigid pipe in flush with wall and ceiling with continuous earth wire connection of 1.5 Sqmm copper wire making good of the concealed portion with suitable colour etc. complete complying with standard specification and as directed by the departmental officers.

Supply and Run of 4 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigd pipe on wall and ceiling with continuous earth wire connection of 10Sqmm Copper with painting of suitable colour etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A FP MCB, 1 no. 16A DP MCB and 2 nos. 6A to 32A SP MCBs on wall with earth connection only. Higher End etc. complete complying with standard specification and as directed by the departmental officers. Lift DB

Supply and Erection of 250A capacity Dust and Vermin Proof Cubical Panel Board made up of 16 SWG CRCA steel with supply and fixing of the following MCCBs with a central bus bar chamber and two nos of cable chambers and confirming to IE rules. (1) 250A FP MCCB with spreader link and Extended Rotary handle-1 No (Higher end) (2) 125A TP MCCB with spreader link and Extended Rotary handle-2 Nos (Higher end make) (3) 63A TP MCCB with spreader link and Extended Rotary handle. 6 Nos (Higher end make) The bus bar chamber will consist of suitable size of tinned copper flat for phase and neutral buses on epoxy moulded bus insulated at proper and sufficient spacing between the buses as per IE Rules. This bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of suitable thickness as partisans. 2 Nos 25x3mm tinned copper flats should be provided all round the panel for earth bus.

The MCCBs should be connected with the phase and neutral buses with suitable size of rigid copper flat/rod and each switch should be connected with the 2 Nos earth bus with 2 runs of No.8 SWG rigid Tinned copper rod with suitable lugs Phase and neutral tinned buses should be tinned properly. The panel should have a separate metering chamber at the top side consisting of Digital function meter, indicator lamps . The panel should be Powder Coat paint of approved colour, approved by the site officer and also the danger board. The capacity of the switches size of incoming and out going cable the place to which the supply is feed shall be mounted on switch chamber. The pannel board should be mounted on 75mm x 37mm MS channel provided all round at bottom of the panel. The whole arrangement should be erected on a masonry pedestal to be constructed with suitable foundation bolts and nuts such that the lowest switch handle is at a height of 0.75 m from the ground level with necessary earth connection (power panel) .

Supply and Erection of 630A capacity Dust and Vermin Proof ACB Panel Board made up of 16 SWG CRCA steel with supply and fixing of the following MCCBs with a central bus bar chamber and two nos of cable chambers and confirming to IE rules. (1) 630A FP MCCB with spreader link and Extended Rotary handle-1 No (Higher end) (2) 400A TP MCCB with spreader link and Extended Rotary handle-2 Nos (Higher end make) (3) 250A TP MCCB with spreader link and Extended Rotary handle. 8 Nos (Higher end make) The bus bar chamber will consist of suitable size of tinned copper flat for phase and neutral buses on epoxy moulded bus insulated at proper and sufficient spacing between the buses as per IE Rules. This bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of suitable thickness as partisans. 2 Nos 25x3mm tinned copper flats should be provided all round the panel for earth bus.

The MCCBs should be connected with the phase and neutral buses with suitable size of rigid copper flat/rod and each switch should be connected with the 2 Nos earth bus with 2 runs of No.8 SWG rigid Tinned copper rod with suitable lugs Phase and neutral tinned buses should be tinned properly. The panel should have a separate metering chamber at the top side consisting of Digital function meter arrangement fuse unit, indicator lamps . The panel should be Powder Coat paint of approved colour, approved by the site officer and also the danger board . The capacity of the switches size of incoming and out going cable the place to which the supply is feed shall be mounted on switch chamber. The pannel board should be mounted on 75mm x 37mm MS channel provided all round at bottom of the panel. The whole arrangement should be erected on a masonry pedestal to be constructed with suitable foundation bolts and nuts such that the lowest switch handle is at a height of 0.75 m from the ground level with necessary earth connection (Main panel)

Supply and clamping of 3 1/2 x 35 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clampsetc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. PVC armoured LTUG cable with earth connection etc. complete complying with standard specification and as directed by the departmental officers.

Supply and providing cable end termination of 3-1/2 x 35 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection completeetc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of 375 mm (15") sweep AC exhaust fan complete with necessary wall opening and making of the wall etc. complete complying with standard specification and as directed by the departmental officers.(Almonard /Crompton /Havells /Equ )

Supply and fixing of louvers shutters arrangements for 375mm (15") sweep AC exhaust fan etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of 400 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with Earth connection only etc. complete complying with standard specification and as directed by the departmental officers.

Supply and clarnping of 3 1/2 x 150 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps etc. complete complying with standard specification and as directed by the departmental officers.

Supply and Laying of 3 1/2 x 150 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make goodetc. complete complying with standard specification and as directed by the departmental officers.

Supply and providing cable end termination of 3-1/2 x 150 sq.mm. PVC LTUGaluminiumarmoured cablewith necessary aluminium cable sockets by crimping etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of brass cable gland for 3-1/2 x 150 sq.mm. PVC armoured LTUG cable with earth connection etc. complete complying with standard specification and as directed by the departmental officers.

Supply, Erection, Testing and Commissioning of 630 KVA,11KV /0.433V Dyn11,ONAN, Indoor Type, double wound, Energy Efficient Transformer with OFF Circuit type. distribution transformer confirming to relevant IS.1180 Level-2 and fitted with the following. 1.Rating &connection diagram plate 2.Earthing terminal 3.Lifting lugs for whole Transformer 4.Cover lifting lugs 5.Oil level gauge-plain with level marking 6.Bottom filter cum drain valve with plug 7.Top filter valve with plug 8. pocket for Thermometer 9.Oil Conservator with drain plug 10.Oil filling point with cap on the conservator 11.Air release plug 12.Silicagel breather 13.Monogram plate 14.Explosion vent with diaphragm 15.Transformer oil 16.Under base channel with skids 17.Oil temperature indicator with A/T Contacts 18.Winding temperature indicator with A/T Contacts

19.Marshaling box 20.Bi-directional rollers. 21.Buchholz relay with A/T Contacts 22.DetachableRadiators. 23.Off circuit tap switch 24.Conservator shut off valve 25. Neutral CT Special accessories The transformer should be supplied with first filling of oil Terminal arrangement:- HV-Cable box,LV-Flange to suit bus duct. All removable covers shall be provided with weather proof hot oil resistant, resistance gaskets, to prevent leakage of water in to core, and oil from the tank with Transformer plinth construction of 630KVA as per IS 1180 etc. complete complying with standard specification and as directed by the departmental officers. (Make CREL/ROWSON /Voltech)

Single VCB Panel For Distance protection:- supply, erection, testing, commissioning and of 11KV 25KA HT Single panel Vacuum Circuit Breaker Switch,Indoor type for Indoor installation, board comprising one group control incomer 630A 500MVA VCB. 1).Draw out type 11KV 500MVA 630A Horizontal Draw out/ Horizontal Isolation VCB operated with spring charged mechanism.Anti Pumping device ,110V DC Shunt Trip and closing Coils (DC source of supply to be derived from a Power pack suitable for 3 Tripping and Two closing operation counter, 4 NO + 4NC spare Aux. Contact for customer use, Automatic safety shutter, Mechanical Close/ Trip knob, Mechanical ON/OFF indication, Operating Handle, 110V AC-110V DC Power Pack etc. (Incom-1 & Outgoing-1No) 2.) 11KV/Root 3/ 110V/Root3- Three Phase, 3 Limb 200VA Class 1 Resin Cast Draw out type Potential transformers complete with HT and LT HRC fuses. (Incoming-1 No) 3)Current Transformers of 100-50/5-5Amps.Dual Core(Core 1-15VA class 1 for metering and core 2-15VA 5P 10 for Protection) Incoming 1 No,Current Transformers of 100/5-5 Amps Dual Core (Core 1-15VA Class 1 for Metering and Core 2-15VA 5P 10 for Protection)(Outgoing-1)

Supply and clamping at 11KV HT 3 core 185 sq.mm XLPE UG cable on wall with M.S. special clamps (From FP HT VCB to Nos 500 KVA Transformer primary side etc. complete complying with standard specification and as directed by the departmental officers.

Supply and providing cable end termination suitable for 11KV 3 core 185 sq.mm XLPE HTUG cable with necessary indoor type heat / cold shinkable joint kit and accessories (Make:RayChem/M.Seal etc. complete complying with standard specification and as directed by the departmental officers.

Supply and laying of 4 runs of 3 ½ x 400 Sqmm PVC armoured LTUG cable on wall with M.S. special clamps etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of 2nos.6/16A two module socket , 2 nos. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of 32A 30mA DP RCBO in sheet steel enclosure in flush with wall and making good of the concealed portion with earth connection etc. complete complying with standard specification and as directed by the departmental officers. (Higher end)

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire with painting of suitable colouretc. complete complying with standard specification and as directed by the departmental officers.

Supply and run of 2 of 6 sqmm PVC insulated SC unsheathed FRLS copper conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 6 sqmm PVC insulated sc unsheathed copper wire and making good of the concealed portion with suitable colour etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of 63A 30mA FP RCBO in sheet steel enclosure in flush with wall and making good of the concealed portion with earth connection etc. complete complying with standard specification and as directed by the departmental officers. (Higher end)

Supply and run of 4 of 10 sqmm PVC insulated SC unsheathed FRLS copper conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sqmm PVC insulated sc unsheathed copper wire and making good of the concealed portion with suitable colour etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of 7 segment 6 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one No 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one No 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in Each segment) and seperate provision for MCB / Isolators ( totally 18 Nos) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following on wall with Earth connection only. i) 63A 4P MCB - 1 no. ii) 63A 4P 30MA RCCB/ELCB - 1 no. iii) 63A DP MCB Isolator -3 nos. iv) 6A to 32A SP MCB - 12 nos. etc. complete complying with standard specification and as directed by the departmental officers. (2Nos.6 & 1No.16A Power Plug Distribution)

Supply and fixing of 8 way Vertical type Triple pole neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal door) with 1No.125A 4 pole MCCB switch as incoming and 4 Nos 63 A TP MCB and 4 Nos 32 A TP MCB as outgoing on suitable angle iron frame work with MS cable entry boxes with earth connection etc. complete complying with standard specification and as directed by the departmental officers. (Higher end) (for 32A TP MCB & 63A FP MCB power Distribution)

Supply and clamping of 3 1/2 x 70 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clampsetc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of brass cable gland for 3 1/2 x 70 sqmm PVC armoured LTUG cable with earth connection . etc. complete complying with standard specification and as directed by the departmental officers.

Supply and providing cable end termination of 3 1/2 x 70 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of brass cable gland for 3-1/2 x 400 sq.mm. PVC LTUG aluminium armoured cable with earth connection etc. complete complying with standard specification and as directed by the departmental officers.

Supply and providing cable end termination of 3-1/2 x 400 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete etc. complete complying with standard specification and as directed by the departmental officers.

MV PANEL BOARD:- Design, Supply, erection, testing and commissioning of 1000A floor mounted MV cubical panel board bus bar chamber dust and vermin proof and accommodating the following ACB's & MCCB's 1 Nos.1000A ACB as Incomer units with the following items of work complete to satisfy the latest IS rules and CEIG guidelines. Supply and fixing of suitable size bus bar chamber made up of 16 SWG MS sheet steel with 4 Nos ie R,Y,B,N. 1” X 1/2”(70mm x 10mm) tinned copper bus bar for 3 phases and neutral and 2 Nos. of earthing bus of size 2”X ¼ (2 x 50mm x6mm) tinned copper bus on suitable bus bar insulator (Epoxy insulator)With maximum creepage distance and supported on MS Base channel frame work ofsize 4”X2”X¼-1Set(100mm x50mm x6mm) Incoming : 1)Supply and fixing of 1 Nos. 1000A basic rating 4 pole 433V LT ACB confirming to IS 13947 – 2 IEC 60947 – 2 for higher breaking capacities of 50KA at 690V AC with all accessories for standard horizontal manual draw out type ACB equipped with auxiliary contacts and all accessories for closing and opening operation with micro processor SR 18 G relay, over current trip device adjustable to LTD, STD and release for over current protection UV release with time delay, EF release short circuit protection, Mains CTs for 3 phases lockout, features, separate mould base for each pole for easy maintenance all relevant protection safety accessories as per CEIG, IE rules inforce with interconnection and terminations as required in specification.

Outgoing: 1) Supply and fixing of 630A 3 Pole MCCB with spreader link and Extended Rotary handle-3 Nos 2) Supply and fixing of 400A 3 Pole MCCB with spreader link and Extended Rotary handle- 6 Nos 3) Supply and fixing of 250A 3 Pole MCCB with spreader link and Extended Rotary handle- 3 Nos Inter connecting the all LT ACB’s and MCCBs to two bus bar with suitable insulated tinned copper flats and painting of phases and neutral indication. Double Earth connection of the MCCBs and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1” X 1/4” Supply and fixing of LED lamp arrangements with toggle switches to the control to each phases and with rigid connection in suitable separate compartments with in the cubicle by CEIG rules with , 2 sets, of supply and fixing Electronic Trivector EC, 300P class 0.5 Base mounting L&T or equivalent.(Make–Model. ER300P class 0.5) Supply and fixing of danger board with siemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc.Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel,concreting, testing and commissioning (L&T) etc. complete complying with standard specification and as directed by the departmental officers.

Supply and erection of 150 KVAR 415/440Volts 50Hz 3 Ph automatic power factor correction panel, 8 stage, (at 0.95 lag), made up of powder coated, 14 SWG CRCA sheet steel enclosure with 1 1/2" x 1 1 1/2" x 1/2" AI Frame work with RCC concreting foundation and bolted to masonry pedestal with 400A Four pole MCCB as incoming (Siemens/C&S) with Delta Connected capacitors (BCH/EPCOS) MOO Type operating in multiple stage with 3 current and Voltage Transducers (CVT) at the phases simultaneously to activate the desired power factor switching time between steps 120 seconds, switching off time in case of fault 3 seconds with a LCD display to show the following Parameters. a. Vr – R phase Line Voltage b. Vy – Y phase Line Voltage c. Vb – B phase Line Voltage d. Ir – R phase Line current e. Iy – Y phase line current2 f. Ib – B phase Line Current g. KW – Present Kilo Watts h. RKVA – Present KVAR Demand i. KVA – Present KVA j. PF – Present Power Factor k. Number of Capacitor bank ON/OFF l. Provision to indicate the imbalanced load m.Provision to indicate the change in phase Sequence n. The APFC Panel Should also have built in protection for current imbalance. For high Voltage/Low Voltage cut off, single phase Preventer, provision for inductor coil to cater the in-rush currents, line surges, Current Limiters, Current Sensor, etc., with connection complete and as per the relevant IE Rules. Eight Stages of Automatic Power Factor control panel with necessary connection.

Supply and providing of maintenance free earthling electrode dual pipe flat technology model maintenance free earth 502 consist of 2mtr long 47mm dia outer pipe with 3.2mm thick 25mm dia inner pipe 2.6mm thick terminal flat of 30x10/12 x 12mm, the entire construction processed with hot tip galvanizing, outer surface up to100 microns all inner annular space filled with highly conductive and non-corrosive nature crystalline material along with electrode moisture booster compound of 1x25 kg bags will be supplied to fill surround the pipe at the time of installation. (Moisure retention, conduction and non-corrosive nature etc. complete complying with standard specification and as directed by the departmental officers. (Galaxy /Ashlok or equivalent)

Preparation of site plan physical layout electrical schematic diagram in 5 sets , getting drawing approval from CEIG preparation of completion report, rectification report and arranging CEIG inspection and obtaining CEIG safety certificate preparation of 2 sets of approved drawing and a copy of safety certificate in a neat frame work to be fixed in HT/Generator room and payment of CEIG inspection fees for HT and 125 KVA Genset etc. complete complying with standard specification and as directed by the departmental officers.

Supply, Erection, Testing, Commissioning and Handing over of 1 No 250 KVA Diesel Generator set of 0.8P.f, Three Phase, 415/420Volts, 50c/s, 1500RPM as detailed below 1.ENGINE: Water cooled Diesel engine suitable for generator application with a shaft Output of 600 BHP at 1500 RPM under NTP Condition as per BSS 5514/IS 10000. The engine shall comprise the following standard scope of supply: (Make Kirloskar/ Cummins/ Ashok Leyland/ Greaves/Equivalent) 1. Dry type Air cleaner 2. Expansion bellow 3. Radiator, Radiator fan and mounting 4. Air to air charge cooler 5. Exhaust Gas turbo charger 6. Lube oil cooler and Lube oil filter 7. Fuel filter(pre and micro) 8. In-line Mono-block fuel injection pump with governor and fuel feed pump 9. Electronic governor 10. 24V Battery charging alternator 11. 24V Volt electric starter motor 12. Engine test Certificate 13. Residential Mufler 14. Fly wheel with starter ring. ENGINE INSTRUMENTPANEL MOUNTED. Engine control panel consisting of ON/OFF/START Key Lube oil pressure guage , oil temperature gauge, high water temperature guage and electronic hour meter and RPM indicator. 1.SAFETY SYSTEM OF ENGINE :-The Engine shall trip for the following conditions with visual alarm device

1. Low lubricating oil pressure 2. High Water temperature 3. Vee-belt failure and over speed 4. The visual indicator should be provide for Low battery indication. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load. 2. ALTERNATOR : Alternator capacity of 250 KVA/ 200 KW,AC 3 phase, 50HZ, 415/420V, 0.8P.F.4 wire self excited, self regulated designed to run at 1500 RPM under NTP conditions confirming to BS 5000/ IS 13364 (part-II) 1992 to be coupled directly to the Diesel engine and test certificate (Make: Kirloskar/ Crompton/ Greaves/ Equivlent.) 3.ACOUSTIC ENCLOSURE:- Acoustic enclosure shall be powder coated and fabricated of 16 SWG CRCA MS sheet.The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC Machine to maintain dimensional accuracy of hole within 0.1mm Powder coating done after seven – tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64 Kg/m density mineral wool of 100mm thickness as Acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt distance shall be less than 75 DBA average or as per CPCB norms. Surface treatment – Painting: The enclosure surface shall be suitably treated for degreasing de-rusting and posphating.

The canopies are passed through seven – tank treatment thoroughly. Additional features of canopies: Canopy fabricated on CNC machines with dimensional accuracy of 0.1 mm so as to increase its durability. Special designed supporting rips/structures are used in canopies so as to give sturdiness and to reduce the vibrations of the DG sets if any World class Cooling package: Canopies shall have cooling package for which it can also perform at 45 degree C/ambient temperature.No grouting required on the ground, only a level surface capable of with standing the DG weight.Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set. 1150.00 30250.00 The Gen set frame shall also be provided with hooks for unloading Temperature rise inside the canopy: Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well within 5-7 deg centigrade. 4. FUEL TANK : 450 liters. Removable fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connection and mechanical fuel gauge. Fuel tank can be easily removed for clearing or any maintenance. 5. BASE FRAME : The base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled, with cross members mounted on AVM. The base frame shall be have provision for mounting of acoustic enclosure on it. The supply of generator set includes loading. Unloading and transportation charges. 6. Battery: 2 Nos 12V 180AHR Battery (Cummins/Kirloskar/Ashok Leyland)

Supply and Run of 10 core 2.5 sqmm armoured copper control cable FRLS in suitable PVC rigid pipe on wall/ Ground/ ceiling etc. complete complying with standard specification and as directed by the departmental officers.

Providing generator Bed of size 6m x 3.66m x 1.20m Height with shed with necessary earth works excavation sand filling, Pcc, brickwork, Centering, Concrete steel fabrication, Plastering, painting finish etc Complete. Providing GI Roof shed for Generator of size 6mx3.66m Using MS square tube Post and parlin top covered with GI Roof Sheet and Painting tinning including fixing in position etc completeetc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of exhaust pipe with silencer. (5m for each set)etc. complete complying with standard specification and as directed by the departmental officers.

Supply and Installation of 1.2meter copper air terminal 5 spike arrestor with base and all fittings mounted on concrete pedestal. etc. complete complying with standard specification and as directed by the departmental officers.

Supply and installation of Aluminium alloy Solid Round Conductor with 8mm dia of material AlMgSi as per IEC 62561-2 with Conductor Hold- er, glue, connectors, joints etc. run on the external wall from terrace to the ground floor in PVC 1" Conduit upto 4meter height etc. complete complying with standard specification and as directed by the departmental officers.

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry etc. complete complying with standard specification and as directed by the departmental officers.

Supply of Safety Accessories 1) AC Chargeable Emergency Lamp 2 x 11W PL Lamp with all connected accessories - 9Nos (for each room) 2.) 2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS - 3sets (5nos each set) 3.) First Aid Box complete with all First Aid Medicines- 2nos, 4.) Shock Treatment Chart fixed in glass frame- 2nos, 5.) Fire Buckets made out of 40 x 40 x 6mm MS Angle - 2 Sets (4nos each set) 6.) Metallic Danger Board as required by the Electrical Authorities- 4nos 7.) Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms - 4nos, 8.) Earth Discharge Rod- 3nos. 9.) Hand Gloves 11KV Grade- 1 pair etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of 3 kVA Online UPS system (with Two hour back up ) with rack arrangement and following specifications and protection against reverse circuit polarity, 440V main input protection, Dynamic short protection with fold back current limiting, low overload, short circuit and pure sine wave output resulting in silent operation of motors and fans. Input voltage : 170V -27V AC Frequency : 50 Hz Input battery voltage : 144 V DC (Make Exide/Numeric/Kirloskar/Numeric/Equivalent) Charger : constant current SMPS charger with full charge cutoff Charging current : Settable upto 8 Amps Inverter: MOSFET Based Full Bridge inverter Output: 230V +/- 3% 50 Hz Output Apparent power: 3000VA Control: Microprocessor based Display : LED display with mains ON, Charger ON, Inverter ON, Battery LOW, Overload Trip

Supply, installation, testing and commissioning of Micro Processor based conventional 4 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc. complete complying with standard specification and as directed by the departmental officers.

Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers etc. complete complying with standard specification and as directed by the departmental officers.. (Make: Apollo / Equivalent)

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers etc. complete complying with standard specification and as directed by the departmental officers.. (Make: Ravel / Equivalent)

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers etc. complete complying with standard specification and as directed by the departmental officers.(Make: Ravel / Equivalent)

Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc. complete complying with standard specification and as directed by the departmental officers.

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection etc. complete complying with standard specification and as directed by the departmental officers.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection etc. complete complying with standard specification and as directed by the departmental officers.

Supply and run of 1 of NO: 8 SWG cu wire for earth connection etc. complete complying with standard specification and as directed by the departmental officers.

Supply, and fixing of GI Hot Dip/Powder coated 16SWG Cable Tray with 300mm width and 50mm Height on suitable angle iron frame on wall or ceiling etc. complete complying with standard specification and as directed by the departmental officers.. (Power supply from Main Panel to Power DBs)

Supply, and Laying of 80mm x 50mm Cable Management Box with Cover on wall or ceiling etc. complete complying with standard specification and as directed by the departmental officers. (For power mains)

Supply and fixing of 120W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting etc. complete complying with standard specification and as directed by the departmental officers.

Supply and run of 25 mm x 6 mm GI flat with necessary insulators at each 0.5mtr and in level and with suitable MS clamp grouted on wall/terrace with necessary bolt and nuts ensuring complete electrical continuity and with rivet joints fixed lightening conductor etc. complete complying with standard specification and as directed by the departmental officers.

Brick work in following Cement Mortarin 1:6 using best quality Fly ash Brick of size 230x110x70mm with class designation of 12.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge.

For foundation and basement

For ground floor

For first floor

Brick partition walls of 11.50cm thickness using best quality Fly ash Brick of size 230x110x70mm with class designation of 12.5 conforming to IS 13757-1993 or IS 12894-2002 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

For ground floor

For first floor

Plastering with cement mortar 1:5 (one cement and five p-sand) 12mm thick in all floors using fine P sand including neat finishing, curing, etc., complete complying with standard specification and as directed by the department officers.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Providing the texture finish to the newly plastered wall with ready made texture putty with patterns at all levels including the cost of coating, labour charges and other incidental charges etc., complete as directed by the departmental officers.arges etc., complete as directed by the departmental officers.

Supplying and laying of 63 mm thick high strength type of interlocking rubber moulded hydraulic pressed paver block of approved colour made up of designed concrete mix 1:1:2 using 10 to 12mm size HBG stone jelly in required shapes and sizes having minimum compressive strength of 40 N/mm2 to be laid in flurrying bone pattern with approved non sticking surface at top. The rate is inclusive of levelling the site, compacting with power compactor and sweeping the sand grouting and also inclusive of transportation charges, loading, unloading and labour charges for laying the paver block, etc. complete and as directed by the departmental officers

Manufacturing supplying and fixing in position of teracotta jally 20x20x7.5cm thick approved quality and design in cement slurry including cost of materials labour curing lifting fixing in position etc, complete complying with standard specification and as directed by the departmental officers in all floors.

Paving the floor with best approved quality fine polished Granite Stone Slabs of following size and Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Designing the Semi Unitised Structural Glazing System with open groove joint as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got approved by the Dept. Officials.) Design the framing system (i.e. male & Female frame) to support vision panels, spandrel panels either with glass or aluminium composite panel, openable, window panels on a continuous framing supported between floors. Also design the split framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated / Monolithic glass, groove width in the system both in horizontal and vertical shall not be more than 20mm. Glazing of panel shall be done only at factory at the controlled atmosphere

Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Paving pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 in Cement Mortar 1:3 (One Cement and Three crushed stone sand), with required Cement Slurry and Mortar Plasticizer, 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of 0f 50 mm tick thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50 x 38x 3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing as directed by the departmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use.

Supplying, fabricating and fixing in position of Aluminium anodised natural colour matt finish of single leaf fully panelled sliding door with 12mm thick bothside prelaminated partile board at the Shutter bottom rail:[email protected] kg/m,Top & Verticle 50x44.45x2.50mm @ 1.292 kg/m,Lock rail 50x44.45x2.50mm @ 1.292 g/m, Running channel section:[email protected] kg/m, and necessary accessories such as Alu.clips 17.15x17.27x1.50mm @ 0.176 kg, Alu handle 100x30mm @ 0.988 kg/mfull length of handles on both sides, lock, roller, including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and waking hole to the required extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition afterfixing etc. complete. All the Alu. sections are to be anodised.with matt finish under electically contolled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc.,

Supplying and fixing in position best quality of approved make white glazed earthernware WASH HAND BASIN (without pedestal) of size 550x400mm with a pair of cast iron brackets , including cost of 15mm diametre brass chromium plated pillar tap, 32mm diametre C.P.waste, 32mm diametre PVC waste pipe with rubber plug and chain, 15mm diametre gun metal wheel valve, 15mm dia brass nipple, 15mm dia nylon connection etc. including fixing the wash hand basin in the wall in position with pair of C.I.brackets with teak wood plugs and screws and giving necessary water supply connection and painting the brackets with two coats of paint over a priming coat of anti-corrosive paint including testing for leakage etc., complete complying with standard specification and as directed by the departmental officers.(The wash hand basin and specials should be got approved by the departmental officers before use on work)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications and as directed by the departmental officers. (The wall putty shall be got approved by the Executive Engineer before use of work). Including Painting New Plastered Wall Surface with Two finishing coats of ready mixed Interior Emulsion of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting two coats of newly plastered wall surface with ready mixed plastic Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the departmental officers.

SAKTHI AND CO (BID ID -1473542)

BLUELEAF PROJECTS PRIVATE LIMITED (BID ID -1474609)