SPL REPAIR TO BUILDING NO T-67 (C COY OR LINE) OF ASC BN UNDER GE (E ) MATHURA

Amount

Dismantling of AC corrugated sheets in roof covering including ridges, hips, valleys etc .

M&L for Pre- painted galvatume aluminum zinc coating GI based semi corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of red colour having tensile strength of 550 Mpa and AZ 150 as in ridges to roof covering, fixed with self tapping screws complete all as specified and as directed.

Dismantling timber scantlings (framed work) exc 40 Sq Cm in section, in any position complete all as specified and directed.

M&L for Mild steel work in tubular trusses, purlins, vetical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240 complete all as specified and as directed.

Dismantling of ceiling boards of any type and any thickness including cover fillets and timber frame work complete.

S&F anodised grid (of size 605 mm x 605 mm) frame make for false ceiling including providing hangers of 2 mm GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x30mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and as directed.

M&L for 4mm thick Non asbestos fibre cement designer building/ceiling boards size (600mmx600mm) fixed with screws to snap grid works in ceiling complete all as specified and directed by Engineer -in-charge

M&L for PCC 1:2:4 Type-B-1 (using 20mm graded stone aggregate) as in Bed blocks, copings.complete all as specified and as directed.

Demolition of brick work built in CM.complete all as specified and as directed.

M&L for brick work with fly ash bricks straight or curved on plan to any radius half brick thick wall built in CM (1: 4). complete all as specified and as directed.

M&L brick work with fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1: 6 complete all as specified.

Taking down cement plaster on brick or stone walls or including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L for rendering 15 mm thick on other than fair faces of brick wall or concrete surface in cement mortar 1:4 mixed with liquid water proofing compound as per manufactures instructions finished even & fair complete all as specified and as directed. Note : Liquid WPC shall be measured and paid seperately under relevant item of this BOQ.

Supply only liquid water Proofing Compound.

M&L for rendering 10mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 finished even and fair complete all as specified and as directed.

M&L for providing damp proof layer in two coats of acrylic polymer coating consisting of 1 part of acrylic polymer liquid mixed with 2 parts of cementious powder applying at the rate of 1.40 Sqm/Kg of mix per coat. Second coat should be applied after 4-6 hrs of first coat, 5 days curing is to be carried out to the surface before providing plastering complete all as specified and as directed. Note : Make of the material 'Smart Care damp block 2K' of Asian paints or equivalent from Dr Fixit, STP, CICA etc. as approved by GE

M&L for preperation of new plastered surfaces of walls and applying two coats of oil bound distember over a coat of alkali resistant primer using spray machine, spray hard to receive area to achieve excellent application using limited manpower complete all as specified and as directed.

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal esistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces incl preparation of newly plastered surface using spray machine, spray hard to receive area to achieve excellent application using limited manpower including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exc 1.5 Sqm and not exceeding 4.00 sqm each. and removing from site complete all as specified and as directed.

S&F 125x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc complete all as specified and fixed complete all as specified and as directed.

M&L PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame complete all as specified and as directed.

35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

M&L for 35 mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

S&F 250mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete.

S&F 200mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed.

S&F 150 mm Aluminium handles cast type anodised. complete all as specified and as directed.

M&L stainless steel wire cloth 0.36mm nominal dia of wire and avarage width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 150mm, Mild Steel ordinary rat tail rod pattern springs including roller and roller plate complete

M&L Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of syntetic enamel paint over a coat of red oxide primer. complete all as specified and as directed.

M&L for preperation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer. complete all as specified and as directed.

S&F Factory made steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F Factory made steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay complete with out glazing bars, dovetailed or welded complete all as specified and as directed.

S&F for 4.0mm thick sheet glass in squares n exc. 0.5 sqm each pane including rubber bead jointing cleat for fixing in position for aluminium window/ventilator all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for 100mm thick cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base, sub floor and paving etc complete all as specified and as directed.

M&L for 80 mm factory made chamfered edge precast concrete interlocking paver blocks any shape and size locally available of best quality and confirming to IS 15658-2006 , M-30 Grade with grey cement and pigments with appproved colour design &pattern as in footpath, parks, lawan,or light traffic ways of required strength made by table vibratory method using PU mould laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, compacted and proper embedding /laying of inter locking paver block into the sand bedding layer through vibratory compaction by using plate vibrator filling the joints with fine sand and cutting of paver block as per required size and pattern finishing and sweeping extra sand complte grey cement and pigments complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar.

M&L for machine cut kota stone flooring 20-22mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing (mirror finish) over and including 15mm thick screed bed in CM 1:4 .

M&L for machine cut kota sone slab 18-20mm thick in skirting, dado and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing (Mirror finish) over and including 10mm thick rendering in CM 1:4

Dismantling wrought iron or mild steel work of any description not otherwise provided for

M&L for 50mm thick Cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate finished cement concrete surface even and fair without using extra cement as in plinth protection laid in panels complete all as specified & directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; cooler stand; gaurd bar framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

M&L for preparation of old painted steel surface of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified and as directed

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded Portionand making good disturbed area complete all as specified.

Dismantling galvanised barbed wire fencing any size,

Excavation in post holes (or similar holes ) each n exc 0.5 cu m getteing out as soft /loose soil rerurning filling in and ramming earth or broken rubble mixed with earth around in layer not exceeding 25 cm complete all as specified.

M&L for PCC 1;3:6 type C-2 using 40 mm graded stone crushed aggregate as in foundation & mass concrete etc complete all as specified.

S&F Mild steel work wind ties, posts and struts in fencing incl cutting tops to shape as required, drilling holes , noching for wire , flat iron fillets for securing wiremesh etc., incl all necessary drilling, bolting or riveting etc & similar work conforming to Fe-290 Gde E-165 and all as specified.

S&F Mild steel screw bolts (machine made) dia of neck 5 to 10 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed

S&F mild steel round bars 10mm dia cut to length, bent to shape as required and fixed in fencing confirming to Fe 410-Wor Fe 290 complete all as specified.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire

supply only MS galvanised chain link any size of mesh as in fencing with complete all as specified

M&L for Preparing new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic paint over and including one coat of red oxide primer complete all as directed

M&L for Preparing new steel surfaces of any description .n. exc 10 cm width or girth and applying two coats of synthetic paint over and including one coat of red oxide primer complete all as directed

Excavation in trenches in soft/loose soil not exc. 1.5m wide and not exc. 1.5m deep and geeting out complete all as specified

M & L for Plain cement concrete in foundation filling type D-2 1:4:8 (using 40mm graded aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified & directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchionsr complete all as specified & directed.

M&L for Reinforced cement concrete (design mix)M-25 (20mm graded aggregates) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified & directed.

M&L for Reinforced cement concrete (design mix)M-25 (20mm graded aggregates) in Columns, pillars, piers, posts and struts complete all as specified & directed.

S&F for TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

S&F for TMT Mild steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

M&L for Framed work Fe-290(Gde E-165)as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified & directed.

M&L for Mild steel plain black sheet in wall clading steel gate and similar work cut to size holes punched including round headed screw clout nails or rivet steel framing with plain 4o mm lap joint with riveted or welded seams complete all as specified & directed.

M & L 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed.

Removing excavated material to a distance n.exc 50M and depositing where directed at a level n.exc 1.50M above the starting point. complete all as specified and directed

Demolition of cement concrete (reinforced) in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work including removing rubbish off the premises complete all as directed

Taking down carefully aluminum/copper point wiring (light ,fan, socket any type, power, bell etc) complete including fixtures & fittings (such as ceiling rose, socket, Pendent, regulator, light fitting etc) and removing the material from site and making good the disturbed surfaces of walls ceiling etc complete all as directed. (Note: Credit for above items should be made as per credit Schedule separately)

M & L for Point wiring with 1.5 Sqmm (nominal area) single core PVC insulated Sheathed (FRLSH) cable, multi-stranded, copper conductor, in universal colour code with & including suitable size of rigid non-metallic PVC conduit (not less then 20mm dia med gd)and its all accessories complete concealed in wall incl cutting & chases( making good all to the disturbed surfaces as per existing) and modular flush metal boxes including cover plate with frame for mounting modular switches, sockets, regulators,socket etc including earth wire of PVC insulated (FRLSH) copper conductor multistranded of 1.5 Sqmm size in green colour complete all as specified in current SSR Part-I & II & directed by the Engineer-in-Charge, as described below:-

One light point/Fan point controlled by one switch 5 amp.

One 3 pin socket outlet 5 amps point controlled by one switch on same board.

One 3 pin socket outlet 5 amps point controlled by one switch, Independent board.

All as per item No.2 here-in-above but for 3 pin/ 5 pin, sockets outlet,15 amps with 4.0 sqmm PVC insulated & Sheathed (FRLSH) cable, independent, Point wiring

M&L ceiling rose, PVC / polycarbonate, isolated body 65mm x 50mm three terminals

S/F switch piano type , SP, one way, flush type 5 Amps complete all as specified.

S/F switch piano flush type 15 Amp, SP, 240 volt, one way complete all as specified.

S/F socket out let 2 in 1 flush type 5 pin 5 Amp complete all as specified.

S/F socket out let 2 in 1 flush type 3 pin 5 & 15 Amp complete all as specified.

S/F fan Regulator piano flush type, electronic step type complete all as specified.

Supply and Fixing Lamp holder, PVC/ Polycarbonate type with back plate suitable for batten

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 1x 20 watt LED Tube fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED lamp, 9 watt, B-22 base complete.

Supply and install of 35W LED building security light fitting with lens & driver, powder coated pressure die cast aluminium, top opening and maintainable with heat resistance toughened glass, built-in Short-Circuit Protection, Over voltage Protection and Surge Protection, IP-65 proction with luminaire efficiecy of greater than 80Lumen/Watt, Colour rendering (CRI) of ≥ 70 and co- related colour temperature (CCT) of 5700K (±500K) . The luminaire should have 10 KV surg protection, PF ≥ 0.9 and total harmonic distortion of THD ≤ 10%, voltage range of 140-280V including all connections complete all as specified.

M&L for building security light bracket made out of 40mm dia light grade GI pipe

Taking down of MCB DBs/ sheet metal enclosure with MCB's/MCCB's

S&F MCB distribution board, SPN 8 way, Double door, sheet steel, phosphatised, powder painted with Copper bus-bar 200Amp, neutral link, earth bar and din rail , cable ties for cable management, 240 V, complete all as specified.

Supply & fixing powder coated CRCA steel sheet MCB distrbution board, IP-43 IK-09 protection, double door recess mounted, triple pole and neutral 4 way complete.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB), TPN 100 Amps, complete with connection

Supply and fixing 240V, 10KA 'C' curve miniature circuit breaker (MCB), SPN 32 amps complete with connection

S&F MCB SP, 6-32 Amps, 'C' series, breaking cap 10 kA, 240V

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V,1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) controlled by remote control all as specified and directed by Engr-in-charge Note: Old fan should be deposited in MES store.

Taking down carefully by Submain wiring/ service connection of any type

M & L for Sub Main Wiring for DB to DB with two runs single core 10 Sqmm PVC insulated Sheathed (FRLSH) cable with stranded copper conductor drawn in suitable size of rigid non-metallic PVC conduit and its all accessories complete concealed in wall/roof with and including 10 Sqmm copper green colour earth wire all as specified and directed by Engineer-in-Charge.(02 run 10 Sq mm single core cable, one run of 6 Sq mm earth wire & One run of PVC conduit will measured as one RM).

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core, laid in trenches / duct / fixing on walls / poles or passing through HDPE double wall corrugated pipe (outer dia should not be less then 40 mm) including connecting with suitable lugs, glands, nuts and bolts in existing Panel from pole / Main Panel Box and testing complete all as specified and directed. Note:- HDPE pipe rate shall be deemed in quoted rate above.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 meter in depth for laying of cable and getting out in soft / loose soil complete all as specified and directed by Engr-in-Charge

Returning, filling in including spreading, levelling, watering and well ramming excavated soil in layers not exceeding 25 cm thick each, back in trenches after cables have been laid and tested,poles, stays , struts have been erected and tested , all as specified.

Removing excavated surplus (soil) obtained from excavation to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete, all as specified.

M&L for earthling complete with galvanized steel earth plate eletrode 60x60 cm x6.3 mm thick burred directly in ground (earth pit not less than 2.25 meters deep below ground level with top edge of the plate not less than 1.5 Metrs below normal ground level connected to galvanized earth lead wire 4.00mm dia by means of bolts, nuts check nuts and washers of galvanized iron or steel all as shown in electrical plate No.5 connected to earthling test point all as specified and indicated including testing on completion including excavation and arth work PCC pit & RCC pit over funnel with watering pipe wire mesh GI protection pipe etc complete.

RANA CONSTRUCTION (BID ID -3522025)

B S ENTERPRISES (BID ID -3521847)

M/S PREETI CONSTRUCTION (BID ID -3522169)

Deepak Saxena (BID ID -3522384)

M/S ANIL KUMAR (BID ID -3521998)

M/s Hoti Lal Contractor (BID ID -3519381)

BHARDWAJ CONSTRUCTIONS (BID ID -3521534)