Construction upgradation of skilled development Centre SHG at village pabhar GP Jamna

Amount

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation & plinth in all shapes and sizes in Cement mortar 1 : 6 ( One cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in Cement mortar 1 : 6 (one cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed and curing complete excluding the cost of centering and shuttering - All work up to plinth level and all floor level in 1:4:8 (one Cement : four coarse sand : eight graded stone aggregate 40mm (forty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

15mm ( fifteen millimeter ) cement plaster on the rough side of single or half brick wall of mix : 1:6 ( one cement: six fine sand ) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

6mm ( six millimeter ) cement plaster of mix 1:4 (one cement : four fine sand) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying reinforced cement concrete work mechanically mixed & vibrated in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor all level mechanically mixed, vibrated and curing complete, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20mm ( twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing form work with steel plates 3.15mm ( three point fifteen millimeter ) thick welded with angle iron in frame 30X 30X5mm ( thirty X thirty X five millimeter ) so as to give a fair finish including centering ,shuttering, strutting and propping etc. with wooden battens and ballies , height of propping and centering below supporting floor to ceiling not exceeding 4.00 meters ( four meters ) and removal of the same for insitu- reinfoced concrete and plain concrete work including all leads and lifts of materials or as per the directions of Engineer in Charge.

Lintels, beams, plinth beams, girders, bressumers and cantilevers including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and placing steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding wire all complete upto floor all level. Thermo-Mechanically Treated bars of grade Fe-500 D or more including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing 35 mm ( thirty five milimetre ) thick factory made laminated veneer lumber door shutters conforming to IS : 14616 & TADS 15:2001 (Part B ), fixing with butt hinges of required size with necessary screws, all complete as per direction of Engineer-in-Charge & panelling with panels of ( Note:- Butt hinges & necssary screws shall be paid separately ) 12 mm ( twelve milimetre ) thick plain grade-1, medium density flat pressed three layers particle board FPT-I or graded wood particle board FPT-1, IS : 3087 marked, bonded with BWP type synthetic resin adhesive as per IS : 848, including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium sliding door bolts, ISI marked anodised ( Anodic coating not less than grade AC 10 as per IS:1868 ), transparent or dyed colour to required colour or shade, with nuts & screws etc. complete 250 x 16 mm ( two hundred fifty into sixteen milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 150 x 10 mm ( One hundred fifty into ten milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium handles ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 100 mm ( one hundred milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing sal wood work in frames of doors, windows, clerestory windows and other frames,wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length ( hold fast lugs or dash fastener shall be paid for separately ), including all leads, lifts, carriage of materials & to the entire satiosfaction of Engineer-in-Charge

Providing 40 x 5 mm ( forty into five milimetre ) flat iron hold fast 40 cm ( forty centimetre ) long including fixing to frame with 10 mm ( ten milimetre ) diametre bolts, nuts & wooden plugs & embedding in cement concrete block 30 x 10 x 15 cm mix 1 : 3 : 6 ( One cement : three coarse sand : six graded stone aggregate 20 mm nominal size ), including all leads, lifts, carriage of materials & to the entire satisfaction of Engineer-in-Charge

Providing & fixing panelling or panelling & glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured ) , panelling or panelled or panelled and glazed shutters 25 mm to 40 mm ( Twenty five milimetre to forty milimetre ) thick Float glass panes 4 mm ( four milimetre ) thick glass panes ( weight not less than 10 ( ten ) kilogram per square metres), including all leads, lifts, carriage of materials & to the entire satiosfaction of Engineer-in-Charge

Providing & fixing factory made ISI marked steel glazed doors, windows & ventilators, side/ top/ centre hung, with beading & all member such as F7D, F4B, K11B & K12B etc. complete of standard rolled steel sections, joints mitred & flash butt welded & sash bars tenoned & riveted, including providing & fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings complete all as per approved design ( Sectional weight of only member shall be measured for payment ) fixing with 15 x 3 mm ( fifteen into three milimetre ) lugs 10cm ( ten centimetre ) long embedded in cement concrete block 15 x 10 x 10 cm ( fifteen into ten into ten centimetre ) of cement concrete 1 : 3 : 6 ( One cement: three coarse sand : six graded stone aggregate 20 mm ( twenty milimetre ) nominal size ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing mild steel Tubular frames for doors, windows, ventilators & cub board with rectangular/L- type sections made of 1.60 mm ( One point six zero milimetre ) thick mild steel sheet, joints mitred welded & grinded finish, with profile of required size, including fixing of necessary butt hinges & screws & applying a priming coat of approved steelprimer. Fixing with 15 x 3 mm ( fifteen into three milimetre ) lugs 10cm ( ten centimetre ) long embedded in cement concrete block 15 x 10 x 10 cm ( fifteen into ten into ten centimetre ) of cement concrete 1 : 3 : 6 ( One cement: three coarse sand : six graded stone aggregate 20 mm ( twenty milimetre ) nominal size ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing fly proof wire gauge to windows, clerestory windows & door with mild steel flat 15 x 3 mm ( fifteen into three milimetre ) & nuts & bolts complete. Galvanised mild steel wire gauge with 0.63 mm ( zero point six three milimetre ) dia wire & 1.4 mm ( One point four milimetre ) aperture on both sides including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing mild steel grills of required pattern in frames of steel windows etc. with mild steel flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm ( twenty into ten into two milimetre ) and braced with flat iron diagonals 20x5 mm ( twenty into five milimetre ) size, with top and bottom rail of T-iron 40x40x6 mm ( forty into forty into six milimetre ), with 40 mm ( forty milimetre ) dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer, including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Mirror polished Kotah stone slab flooring over 20 mm ( twenty milimetre ) ( average ) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing & polishing complete with base of cement mortar 1 : 4 ( one cement : four coarse sand ) 19 mm ( ninteen milimetre ) thick, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Mirror polished Kotah stone slab 20 mm ( twenty milimetre ) thick in risers of steps, skirting, dado & pillars laid on 12 mm ( twelve milimetre ) ( average ) thick cement mortar 1 : 3 ( One cement : three coarse sand ) & jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing & polishing complete, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & laying vitrified charge floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08 % & conforming to IS 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1 : 4 ( One cement : four coarse sand ), jointing with grey cement slurry @ 3.3 Kg ( three point three Kilogram ) per square metres including grouting the joint with white cement & matching pigments etc. complete size of tile 600 x 600 mm ( six hundred into six hundred milimetre ) , including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & laying vitrified charge tiles in different sizes ( thickness to be specified by manufacturer ) , with water absorption less than 0.08 % & conforming to IS 15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 : 3 ( One cement : three coarse sand ), jointing with grey cement slurry @ 3.3 Kg ( Three point three Kilogram ) per square metres including grouting the joint with white cement & matching pigments etc. complete size of tile 600 x 600 mm ( six hundred into six hundred milimetre ) , including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Distempering with oil bound washable distemper of approved brand & manufacture to give an even shade new work ( two or more coats ) over and including water thinnable priming coat with cement primer including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing walls with Acrylic smooth exterior paint with of required shade new work ( two or more coat ) applied @ 1.67 litre/10 Sqmt ( one point six seven litre per ten square metres ) over & including priming coat of exterior primer applied @ 2.20 Kg /10 Sqmt ( at the rate two point two zero kilograme per ten square metre ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Wood work with Deluxe Multi Surface Paint of requied shade. Two or more coat applied @ 0.90 ltr/ 10sqm( zero point nine zero litre per ten square meter ) over an under coat of primer applied @ 0.75 ltr/ 10sqm( zero point seven five litre per ten square meter ) of approved brand and manufacture complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint of requied shade. Two or more coat applied @ 0.90 ltr/ 10sqm( zero point nine zero litre per ten square meter ) over an under coat of primer applied @ 0.80 ltr/ 10sqm( zero point eight zero litre per ten square meter ) of approved brand and manufacture complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position & applying a priming coat of approved steel primer using structural steel etc. as required in grating, frames, guard bars, ladders, railing, brackets, gates & similar work including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint of requied shade. Two or more coat applied @ 0.90 ltr/ 10sqm( zero point nine zero litre per ten square meter ) over an under coat of primer applied @ 0.80 ltr/ 10sqm( zero point eight zero litre per ten square meter ) of approved brand and manufacture complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

RAKESH KUMAR (BID ID -521809)

Suresh Kumar (BID ID -522605)