Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹17.1 CrAccepted-AOC | ₹17.1 Cr | L1 | Accepted-AOC L1 |
| 2 | L2₹17.7 CrRejected-AOC A 403 CITY CENTRE NEAR RESHAMBHAVAN STATION ROAD SURAT 315003 | 315003 | ₹17.7 Cr | L2 | Rejected-AOC L2 |
| Sl No | Description | Qty | Unit | M/s. Natvar Construction Co. L2 | Unique builders L1 |
|---|---|---|---|---|---|
| 1.00 | C-01 Interior works -Only Ceiling & Finishing
Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable crews for cement particle board in ceiling etc. complete (frame work to be paid seperatately).
6 mm thick Cement fiber board, Type-B, Category-III as per
IS: 14862 : 2000 | 1 | Sqm | 3,500 ₹3,500 | 3,500 ₹3,500 |
| 2.00 | Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/ moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately. | 5,117 | Sqm | 3,800 ₹1.9 Cr | 3,800 ₹1.9 Cr |
| 3.00 | Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured
out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 5 mm thick corrugated (2.5” or 4.2” or 6”) or step-down (2” or 3” or 6” ) as specified | 300 | Sqm | 6,100 ₹18.3 L | 6,200 ₹18.6 L |
| 4.00 | Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete. | 6,000 | Sqm | 550 ₹33 L | 500 ₹30 L |
| 5.00 | Add for plaster drip course/ groove in plastered surface or moulding to Door and windows projections. | 9,799.36 | Mtr | 400 ₹39.2 L | 400 ₹39.2 L |
| 6.00 | Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. Sal wood | 3.76 | Cum | 3,90,000 ₹14.7 L | 4,00,000 ₹15.0 L |
| 7.00 | Providing material and labour for roughened strip 2.5 cm wide to form antiskid surface on treads of stairs in any type of stone including forming straight deep curved gishi (groove), 6 mm wide & 4 mm deep on two sides of the roughened area, chiseling, polishing the edges, sides and bottom of gishi etc. complete as per sample approved for all floor, all height. Only one time length of tread of stair shall be measured for payment. | 2,371.14 | Mtr | 200 ₹4.7 L | 200 ₹4.7 L |
| 8.00 | AddProviding material nd labour for rounding the edges of granite slab with suitable grades of rinding/polishing material approved by the Architect/Engineer-In-Charge. The cost includes all nsumables,tools and labour for the rounding of granite, wiping, cleaning,washing etc all complete as per the direction of Engineer-In-Charge Molding In staircase with dhar polish | 2,371.14 | Mtr | 400 ₹9.5 L | 400 ₹9.5 L |
| 9.00 | Factory made single extruded WPC (Wood Polymer Composite) solid door/window, clerestory windows & other Frames/Chowkhat of frame size 65 x 150 mm | 550 | Mtr | 2,500 ₹13.8 L | 2,500 ₹13.8 L |
| 10.00 | Providing and fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Rockwool conforming to IS: 8183,density 48 kg/ m3, 50 mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24
gauge wire mesh, for top most ceiling of building. | 5,101.75 | Sqm | 700 ₹35.7 L | 700 ₹35.7 L |
Tender Value
₹14.0 Cr
EMD Value
₹24.0 L
Closing Date
13 Mar 2026, 2:00 pmClosed
Executive Engineer (PC),PWD,DNH,Silvassa
PWD Campus Block No.I(Bldg), DNH, Silvassa
Providing and installing MEP and mandatory Civil works required for Strengthening of the Health infrastructure in the UT of DNH
2026_UTDNH_7939_1
E-TENDER NOTICE NO.56 OF 2025-26 (PC)
Open Tender
Civil Works - Buildings
120 days
UT OF DNH
As per NIT refer
3 documents required · 3 mandatory
₹5,000
Executive Engineer (PC),PWD,DNH,Silvassa
₹24.0 L
28 Mar 2026
26 Feb 2026
13 Mar 2026
26 Feb 2026
13 Mar 2026
26 Feb 2026
C-01 Interior works -Only Ceiling & Finishing Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable crews for cement particle board in ceiling etc. complete (frame work to be paid seperatately). 6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 : 2000
Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/ moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately.
Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 5 mm thick corrugated (2.5” or 4.2” or 6”) or step-down (2” or 3” or 6” ) as specified
Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.
Add for plaster drip course/ groove in plastered surface or moulding to Door and windows projections.
Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. Sal wood
Providing material and labour for roughened strip 2.5 cm wide to form antiskid surface on treads of stairs in any type of stone including forming straight deep curved gishi (groove), 6 mm wide & 4 mm deep on two sides of the roughened area, chiseling, polishing the edges, sides and bottom of gishi etc. complete as per sample approved for all floor, all height. Only one time length of tread of stair shall be measured for payment.
AddProviding material nd labour for rounding the edges of granite slab with suitable grades of rinding/polishing material approved by the Architect/Engineer-In-Charge. The cost includes all nsumables,tools and labour for the rounding of granite, wiping, cleaning,washing etc all complete as per the direction of Engineer-In-Charge Molding In staircase with dhar polish
Factory made single extruded WPC (Wood Polymer Composite) solid door/window, clerestory windows & other Frames/Chowkhat of frame size 65 x 150 mm
Providing and fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Rockwool conforming to IS: 8183,density 48 kg/ m3, 50 mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.
5 mm thick solid foam PVC panel of required size with moulded/ extruded beading of appropriate design shape and size as per manufacturer’s specifications ( to secure the panel insert tight in place within the style and rails of shutter) matching the colour and shade of shutter frame. Decorative type.
Water Body item Water Body of 4.5 x 4.5 x 0.45 mtr in porch area including plumbing, waterproofing, MS jali work as per given design, stone cladding, statue/murti base, plantation, water fall, electric motor for water fall, water pump, required electrical work for lighting & water fall etc. complete as directed by Engineer-In-Charge. Complete in all erspect required for the same.
C-02 Water Proofing Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. “All above operations to be done in order and as directed and specified by the Engineer-in-Charge”: 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
water replant chemicale for roman tiles Applying breathable, non-reactive, antifungal, and water repellant Silane/Siloxane chemical as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand and manufacture, diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the existing sand stone masonry surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer-In-charge (The rate is inclusive of all materials & labours involved except scaffolding).
C-03 Extranal Devlopment borewell Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. All types of soil 350 mm dia metre
Sprinkler irrigation system 10m radius rain gun.
Sprinkler irrigation system rain gun boiler.
Sprinkler irrigation system rain gun motter.
Sprinkler irrigation system rain gun filleter.
Polyethylene water storage tank with cover and suitable locking arrangement 5000 liter tank.
G.I. pipes 80 mm dia
Pump room
C-04 Extranal Finishing Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
C-05 ELECTRICAL SYSTEM INSTALLATION SUPPLY AND INSTALLATION OF LIGHT FIXTURES SITC of Light fixtures including all civil works 1x15W Bollard(1mtr)
1x12W LED spot Light
1x40W Pole Light(4mtr)
1x60W Pole Light(6mtr)
1W Down Led Wall Light
70W Linear Wallwasher Light
9W Recessed Mount LED Light
15W Recessed Mount LED Light
15W Rounded Panel Light
12W Wall Light
15W Wall Light
Bulk Head Light
40W LED Tube Light
36W Chandlier Light
Supply Installation Testing and Commisioning of occupancy sensor for toilets
SWITCHGEARS, DBs & MCBs Providing & erecting 240V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS: 8828 in existing box having following capacity. 40 Amp. (Cat. III)
Providing & erecting 240V MCB three pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS: 8828 in existing box having following capacity. 6 to 32 Amp. (Cat. III)
Providing & erecting 240V MCB three pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS: 8828 in existing box having following capacity. 40 Amp. (Cat. III)
Providing and erecting Sheet Steel powder coated MCB distribution board – flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 with out MCB to house appropriate nos. of MCBs. (The DBs should be used of same company of MCB to be used). Single phase 18 way SS Double door.
Providing and erecting Sheet Steel powder coated MCB distribution board – flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 with out MCB to house appropriate nos. of MCBs. (The DBs should be used of same company of MCB to be used). Three phase 6 way VTPN SS Double door for three phase/ single phase outgoing vertical box.
Providing and erecting Sheet Steel powder coated MCB distribution board – flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 with out MCB to house appropriate nos. of MCBs. (The DBs should be used of same company of MCB to be used). Three phase 8 way VTPN SS Double door for three phase/ single phase outgoing vertical box.
Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 100 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240V. having charectorstic of quick action & tripping with all advance feature & do not incorporate any electronic component for following Max. rating erected as directed. 40 Amps. DP (Cat. III)
Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on 3 phase and neutral 415V. having charectorstic of quick action & tripping with all advance feature & do not incorporate any electronic component for following Max. rating erected as directed. 63 Amps. FP (Cat. III)
CABLE TERMINATION BOXES FOR DBs Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing / covering Extra wires & Cables, suitable for following size of MCB DB Box. Single Phase 18 Way.
Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing / covering Extra wires & Cables, suitable for following size of MCB DB Box. Three Phase 6 Way VTPN.
Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing / covering Extra wires & Cables, suitable for following size of MCB DB Box. Three Phase 8 Way VTPN.
MV CABLES & CABLE LAYING Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing cable trench / pipe of following size of cables. 2 core 4 Sq. mm.
Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing cable trench / pipe of following size of cables. 2 core 6 Sq. mm.
Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing cable trench / pipe of following size of cables. 2 core 10 Sq. mm.
Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing cable trench / pipe of following size of cables. 2 core 16 Sq. mm.
Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing cable trench / pipe of following size of cables. 3½ core 240 Sq.mm(120 Sq.mm ½ core)
Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. 4 core 25 Sq. mm.
Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. 4 core 35 Sq. mm.
Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. 4 core 50 Sq. mm.
Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. 4 core 70 Sq. mm.
Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. 4 core 120 Sq. mm.
Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. 4 core 150 Sq. mm.
Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. 4 core 185 Sq. mm.
Providing and erecting XLPE (IS: 7089) (I) -88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. 4 core 240 Sq. mm.
MV CABLE TERMINATION 3 core 150 Sq. mm.
3 ½ core 240 Sq. mm.
C-06 PHE Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200 mm length), fixed to roof slabs by means of ceiling cleats made out of 40x3 mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineerin- charge. fire
Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200 mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3 mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineerin- charge. pulmbing
Supplying and installing Compressive Strength 100 kPa and joint geo rex pipe
A. SANITARY AND CP FITTINGS Providing and fixing Stop cock, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 20mm dia. including all required ccessories and connections. Make: Jaquar, Kohler, Grohe, Cera high end series.
Supply, installation, testing and commissioning of brass chromium plated Mixer Sink Cock including all fittings, accessories and connections. Make: Jaquar, Grohe, Hindware, Kohler, Cera
Providing and fixing 5 Ltr Instant water geyser with flexible connection fittings arrangement 4 level safety 3000 watts fast heating element with pressure release valve.rust proetc.of body complete of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years water tank and 2 year element.only skilled and experienced person shall be employed for this purpose. Make: v guard, racold,jaquar
Supply of multitube type disinfection system comprising of U.V and U.F Reactor in a close circuit chamber with required no of lamps as per detail design on flow conditions with auto dosing controller, display monitor as per manufacturers requirement complete in all respects.99.99% bacteria free mineral water,removes chlorine taste & odour 7.9 lpm flow rate, 0.2 micron filtration, zero wastage, no electricity needed,including cuno prefilter with cartridge, including 3m tap- 1 LAKH LTR CAPACITY
Fixing, Testing and Commissioning at site Under count Wash Basin with basin mixture and accessories Flexible Connection tube, 32 mm C.P. brass waste coupling of standard pattern, and union including cutting and making good the walls wherever required complete.Queo - (FEDRA +F Elegant)/ KOHLER K5373IN-0, OR Equ. (Inside Toilets)
Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white including cutting holes in walls and making good the same but excluding fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm size
Fixing, Testing and Commissioning at site ablution Health Spray Faucet with wall hook and 1.2 mtr. Chrome plated PVC hose pipe, etc. complete in all respects. Queo - Addons/Kohler/Grohe
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. Make: Jaquar, Kohler, Grohe, Cera high end series.
Providing and fixing sanitary fixtures for handicapped toilet including one wash basin of approved size, one pair mounting brackets and all other related CP brass fittings like pillar cock, bottle trap,angle valve,waste coupling etc.One number EWC & Cistern with raised soft push button for convenient access complete with fittings & seat cover , one no.stainless steel hinged rail 76 cm & five nos. of stainless steel grab rails 60 cm and one no.of Faucet with spatula lever etc of approved make as per drawing & as per manufactures specification .The rate is including cost and conveyance of all materials, labour charges, lead,lift,cutting and making good the walls,floors,slab wherever required etc complete, testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer-in-charge at all levels. Make: Jaquar, Kohler, Grohe, Cera high end series.
Providing and fixing gloss white cast acrylic construction reinforced marble freestanding JACUZI 1700 x 800 x 565 or nearest size with slip resistant surface, of approved quality and make, waste coupling, bath tub over flow with floor flange accessory pack, pop up waste, masonry / concrete supports, etc. complete including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of gloss white cast acrylic construction reinforced marble freestanding bath tub including all acessories shall be taken as Rs. 343960/- and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose. Make: Jaquar, Kohler, Grohe
B. SOIL, WASTE, VENT & RAIN WATER PIPES Supplying, Fixing, testing and commissioning at site SDR-11 grade Chlorinated Polyvinyl chloride (CPVC) pipes confirming to ASTM D:1785 & CPVC fittings suitable for solvent welded joints, including all necessary fittings like Tee, Elbow, Adaptors, etc, Chasing and making good the walls wherever required, providing necessary brass ended terminal fittings (For Condensate A/c drain) 20 mm ID (¾’’) dia (Concealed)
Supplying,fixing, testing Micro cellular closed cell Nitrile rubber elastomeric insulation(UL-94 Approved) tubes/sheets (9mm thick) for the hot water supply pipes with protective glass fabric & co-extruded polymeric covering for UV & mechanical protection. (For A/C drain) -22 mm
C. WATER SUPPLY (INTERNAL AND EXTERNAL) Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR-11 grade pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. as per direction of Engineer in Charge. Internal work - Exposed on wall ½ ''(15mm) dia.(Internal / Concealed) water supply
¾ ''(20mm) dia. (Exposed on wall /ceiling) Cold water supply
1 ''(25mm) dia. (Exposed on wall /ceiling) Cold water supply
1¼ ''(32mm) dia. (Exposed on wall /ceiling) Cold water supply
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR-11 grade pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. ½ ''(15mm) dia.(Internal / Concealed) water supply
¾ ''(20mm) dia. (Internal / Concealed) water supply
Supplying, fixing, testing Micro cellular closed cell Nitrile rubber elastomeric insulation(UL-94 Approved) tubes/sheets (9mm thick) for the hot water supply pipes with protective glass fabric & co-extruded polymeric covering for UV & mechanical protection. (For CPVC) ½ ''(15mm) dia.
¾ ''(20mm) dia.
1 ''(25mm) dia.
1¼ ''(32mm) dia.
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR-11 grade pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. as per direction of Engineer in Charge. Internal work - (Internal /External / In shaft) 1¼”(25mm) dia (External / in Shaft)
1¼”(32mm) dia (External / in Shaft)
1 ½” (40mm) dia (External / in Shaft)
Supplying,Fixing, testing and commissioning at site in positions Automatic Air Release Valves, ball valves of approved quality and make on the top of the vertical water supply pipes as per specification and drawings 1/2"(15mm) dia
Supplying,Fixing at site in position full way lever operated forged brass gate valve of brass body with forged brass hard crome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings ½ ''(15mm) dia.Globe valve
¾ ''(20mm) dia. Globe valve
1” (25mm) dia.Globe valve
1 ¼ “ (32mm) dia.Globe valve
1 1/2 “ (40mm) dia.Globe valve
2” (50mm) dia.Globe valve
Providing, Fixing at site in position CI Butterfly valve (PN 16) wafer type of approved make with necessary PVC flanges, gaskets, nuts and bolts etc complete within position as per drawings. 2” (50mm) dia
2 ½” (65mm) dia
3” (80mm) dia
NON RETURN VALVE cast Iron double flange as per IS/5312 PN 1.6 rating complete with Bronze body & wedge Stainless Steel spindle, Gland packing, Rubber gasket 1” (25mm) dia
1 ¼ “ (32mm) dia.
1 1/2 “ (40mm) dia.
2 ” (50mm) dia
2 ½” (65mm) dia
3” (80mm) dia
Supplying and fixing pressure reducing valve with all accessories including cost and conveyance of all materials,labour charges etc complete as directed by the Engineer-in-Charge at all levels 25 mm nominal bore
32 mm nominal bore
Providing, Fixing at site in position uPVC Pipes (as per ASTM D – 1785 sch-40 ) of approved make For Cold Water Supply, complete with all necessary (ASTM D – 2466/2467) fittings (elbows, unions, tees, reducers, couplings, nipples etc) (External / Inshaft) 25mm dia
32mm dia
40mm dia
50mm dia
Providing, Fixing at site in position uPVC Pipes (as per ASTM D – 1785 sch-80 ) of approved make For Pumping line from ( Sump Tank To Over head Tank) complete with all necessary (ASTM D – 2466/2467) fittings (elbows, unions, tees, reducers, couplings, nipples etc) 40mm dia
50mm dia
2 ½” (65mm) dia
3” (80mm) dia
Supplying, Fixing, testing and commissioning at site Puddle Flange fabricated from Upvc ASTM Grade sch-80 pipes & uPVC sheet (600 mm long) 1 ¼ “ (32mm) dia.
1 ½” (40mm) dia (External / in Shaft)
2” (50mm) dia (External / in Shaft)
2 ½” (65mm) dia (External / in Shaft)
4” (100mm) dia (External / in Shaft)
6” (150mm) dia (External / in Shaft)
8” (200mm) dia (External / in Shaft)
6” (150mm) dia -Mild Steel Material , single side flange
8” (200mm) dia -Mild Steel Material , single side flange
Hot dip galvanized (Fully exposed to weather and wet areas)
B. SOIL, WASTE, VENT & RAIN WATER PIPES Supplying, Fixing, testing and commissioning at site in position uPVC pipe -6kg/cm2) (IS:4985) Solvent Welded fittings with bosses where required e.g. tees, bends, coupling, door bends, junctions, cowls, etc., complete. (Soil & Waste in Shaft) Make: Astral/Supreme/Ajay IN SHAFT 160 mm O.D. (6Kgf/cm2 IS:4985)
110 mm O.D. (6Kgf/cm2 IS:4985)
75 mm O.D.(6Kgf/cm2 IS:4985)
63 mm O.D ( 4Kgf/cm2) Vent pipe in shaft
Providing, Fixing, testing and commissioning at site in position uPVC pipe ( IS : 4985 ) With Rubber Ring or Solvent Welded fittings with bosses where required e.g. tees, bends, coupling, etc. complete. (For Rain water pipes in shaft & Ceiling) Make: Astral/Supreme/Ajay IN SHAFT ( PASTING ONLY) 75 mm O.D. ( 4Kgf/cm2)) Rain water pipe in shaft& floor
110 mm O.D ( 4Kgf/cm2)) Rain water pipe in shaft
160 mm O.D ( 4Kgf/cm2)) Rain water pipe in shaft
Supplying, Fixing, testing and commissioning at site in position u PVC pipe of 6Kgf/cm2including PVC fittings with bosses where required e.g. tees, bends, coupling and adapters and jointing with adhesive approved by fitting manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site universal clamps & anchor fasteners(8mm) , threaded rod(8mm),nuts ,washers, wherever required etc. complete.Make: Astral/Supreme/Ajay (For Internal Soil &Waste line) (PASTED ONLY) 40 mm O.D. (6Kgf/cm2 IS:4985)
50 mm O.D. (6Kgf/cm2 (IS:4985)
75 mm O.D. (6Kgf/cm2 (IS:4985)
110mm O.D (6Kgf/cm2 (IS:4985)
32 mm O.D. (8Kgf/cm2 (IS:4985) for sunken spout
Providing, Supply, installation,testing and commissioning of UPVC Oil Waste system conforming to DIN-EN-12056 & DIN-1986-100 fittings (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offSet and other specials. Jointing shall be done with pushfit EPDM ring jointing technique in general. Solvent cement joints may be provided for fittings and specials which are not manufactured with pushfit rubber joints. Pipes may be laid / fixed in sunken floors, under slung from ceiling. The pipes laid in sunken floor shall be encased with 75 mm thick cement concrete (1:2:4) all around. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. 50mm Dia
75mm Dia
110mm Dia
160mm Dia
Providing, Fixing, testing and commissioning at site in position Low noise - Multi floor trap/ P trap 110/75 mm. with suitable supporting on GI slotted rails (1.6mmthick) full threaded rod, anchor fasteners etc. 110/75/50 mm dia outlet
Supplying, Fixing, testing and commissioning at site in position Deep Seal UPvc fabricated Multi floor trap (7”), with suitable supporting on GI slotted rails (1.6mmthick) full threaded rod, anchor fasteners etc. complete in all respects. 50/75 mm dia outlet (In Ceiling)Astral/Supreme/Ajay
Supplying,Fixing, testing and commissioning at site in position UPvc fabricated Multi floor trap (4”), with 50/75 mm dia outlet (In Sunken slab & floor raising areas)Astral/Supreme/Ajay
Supplying & Fixing CI Hubless pipe as per EN 877 with stainless steel coupling with EPDM rubber gasket jointng as pe DIN‐ 19543, ASTM C 1277‐4 including cutting masonry or walls, etc. wherever necessary for making connections, Supplying & Fixing the pipe to Ceiling, including spare socket, scaffolding wherever necessary, painting the exposed faces with suitable anticorrosive paint and 2 coats of oil paint recommended by the Architect / Consultant.Supplying & Fixing CI Hubless pipe as per EN 877 with stainless steel coupling with EPDM rubber gasket jointng as pe DIN‐ 19543, ASTM C 1277‐4 including cutting masonry or walls, etc. wherever necessary for making connections such as Bends, Tees, Cross, Wye, etc 50 mm Dia
80 mm Dia
110 mm Dia
150 mm Dia
Multifloor trap/P Trap
Supply and fixing of DRAINAGE GRATING WITH TROUGH, 60x60x8+10 • Trough using 1 mm thick 304 grade #4 stainless steel • Grating using 2 mm thick 304 grade #4 stainless steel
Supply and fixing of DRAINAGE GRATING WITH TROUGH, 30x30x8+10 • Trough using 1 mm thick 304 grade #4 stainless steel • Grating using 2 mm thick 304 grade #4 stainless steel
Supplying,Fixing, Testing and commissioning at site in position stainless steel square frames (150x150) ss304 POP UP GRATINGS (for Washing machine)Fixing, complete in all respects Chilly/Eligna/
Supplying,Fixing, testing and commissioning at site in position Concealed floor trap (4” UPvc fabricated Trap, with Stainless Steel Square frames (150x150mm) SS (304), Rubber Seal and flat round cover with screw. etc. complete in all respects. Chilly/Eligna/
Supplying,Fixing, testing at site in position 160mm dia square /circular grating Terrace rain water outlet (Cast Iron)(for 110mm dia pipe)
Supplying, Fixing, testing at site in position PVC Roding Eye (6kg/cm2) Complete in all respects. 160 mm dia
110 mm dia
75 mm dia
Supplying,Fixing, testing and commissioning at site in position SS Floor cleanout with Stainless Steel Square frames (150x150mm) SS (304), Rubber Seal and flat round cover with screw. etc. complete in all respects. 110 mm dia
C-07-LIFT OPD BLOCK Design, fabrication, supply of electric traction type with machine roomless type, Stainless steel 15 Passenger (1020Kg) elevator (including freight & landing charges ,insurance and all applicable taxes and duties in country of origin and in India etc.without GST) and type suitable for operation on 415 V ± 10%, 3 phase , 50 Hz AC supply, having AC variable voltage and variable frequency micro-processor type traction control, speed of 1 Mtr/sec ,electromagnetic brake system, Duplex mode operation, operating panel with luminous buttons, over load warning indicator, battery operated alarmbell, LED type emergency light, intercom suitable for hook upto Purcahsers's EPABX, infrared ray sensing door protection for full height, reverse phase relay on controller, fireman’s switch at initial landing floor, LCD/LED car positions and direction indication in car and landings and at all floors with UP/DOWN direction, shaft wiring and lighting with accessories, braille buttons, Automatic Rescue Device (ARD) with dry maintenance free sealed batteries,Safe landing device and Battery Operated Emergency Rescue Device and all electrical components with wiring from the single point power supply provided at top landing near the elevator door audio announcement along with prerecorded message as approved by Engineer-in-Charge. The drives of elevator shall meet the requirements of IEEE 519/2014. The PMSM traction motor( IE3 or better efficiency) of machine roomless elevator shall be of gearles type and placed inside the elevator hoistway complete as per technical specification. Having automatic side opening Stainless steel Hairline AISI441 door, stainless steel car enclosure provided with stainless steel handrails on two sides as applicable in accordance of following details:2 stops & 2 openings and entrance & exit at same side and suitable for travel height of 4 mtrs. (Shaft Size 2000mm (width) x 3000mm (depth) ) with car opening of 1000mm (width) and 2200 mm (height)2400 mm deep . complying with the net inside car area as per IS14665 part 3/1) Car design Stainless Steel - Milkyway and door opening of 900mm (width) and 2100mm (height). The equipment should be BMS compatible and shall haveprovision for CCTV installation . All electrical components with wiring from the single point power supply provided in last landing near the elevator door. All fabrication and procedures shall confirm to relevant IS ,Yes Gong in Car Emergency Rescue Device with audio announcer 2 Way Dedicated Intercom Attendant Service Lift Announcer Round spot LED light Interface only B, 2 Hours Fire rated standards and complete in all respects as per technical specifications
TYPE A&B Design, fabrication, supply of electric traction type with machine roomless type, Stainless steel 15 Passenger (1020Kg) elevator (including freight & landing charges ,insurance and all applicable taxes and duties in country of origin and in India etc.without GST) and type suitable for operation on 415 V ± 10%, 3 phase , 50 Hz AC supply, having AC variable voltage and variable frequency micro-processor type traction control, speed of 1 Mtr/sec ,electromagnetic brake system, Duplex mode operation, operating panel with luminous buttons, over load warning indicator, battery operated alarmbell, LED type emergency light, intercom suitable for hook upto Purcahsers's EPABX, infrared ray sensing door protection for full height, reverse phase relay on controller, fireman’s switch at initial landing floor, LCD/LED car positions and direction indication in car and landings and at all floors with UP/DOWN direction, shaft wiring and lighting with accessories, braille buttons, Automatic Rescue Device (ARD) with dry maintenance free sealed batteries,Safe landing device and Battery Operated Emergency Rescue Device and all electrical components with wiring from the single point power supply provided at top landing near the elevator door audio announcement along with prerecorded message as approved by Engineer-in-Charge. The drives of elevator shall meet the requirements of IEEE 519/2014. The PMSM traction motor( IE3 or better efficiency) of machine roomless elevator shall be of gearles type and placed inside the elevator hoistway complete as per technical specification. Having automatic side opening Stainless steel Hairline AISI441 door, stainless steel car enclosure provided with stainless steel handrails on two sides as applicable in accordance of following details:2 stops & 2 openings and entrance & exit at same side and suitable for travel height of 4 mtrs. (Shaft Size 2000mm (width) x 3000mm (depth) ) with car opening of 1000mm (width) and 2200 mm (height)2400 mm deep . complying with the net inside car area as per IS14665 part 3/1) Car design Stainless Steel - Milkyway and door opening of 900mm (width) and 2100mm (height). The equipment should be BMS compatible and shall haveprovision for CCTV installation . All electrical components with wiring from the single point power supply provided in last landing near the elevator door. All fabrication and procedures shall confirm to relevant IS ,Yes Gong in Car Emergency Rescue Device with audio announcer 2 Way Dedicated Intercom Attendant Service Lift Announcer Round spot LED light Interface only B, 2 Hours Fire rated standards and complete in all respects as per technical specifications
C-08 UPS SITC of 40kVA Frame with 30kVA modules three phase in and out. with indoor (IP21) with surge protection system with 60 min backup battery @ 30kva 0.8 PF load with min VAH of 60000 Dual string (SMF battery of reputed approved make. Input pf >0.99, with external input isolation transformer, with IGBT rectifier and inverter Double conversion technology, with input voltage range 320-460 @ full load, 50Hz Three Phase, output 400V, 50Hz Three phase, compatibility etc. Output Voltage THDu <6% Full Non-Linear Load According to IEC/EN62040-3including all accessories, frequency regulation 50Hz±0.01%, SMF batteries VRLA type with powder coated CRCA cabinet including all accessories such as output panel required for ups parallels operation, cabling etc as required complete having following specification. The UPS system consist of one numbers of UPS unit and one set of battery bank . The UPS shall be suitable for parellel operation. RS485 Interface compatibility Fully digital controlled based on DSP Power factor corrected from end > 0.9 Pure sine wave output. Full time output voltage & frequency regulation Auto regulation of battery end voltage Intelligent interface with LED/LCD display Static bypass switch / manual by pass switch Auto temperature compensation, Remote Management Interphase, Back up time 30 minutes at full load.
Supply, installation, and commissioning of 1KVA 1 phase in and 1 phase out tower type online double conversion pure sine wave UPS system. (SMF battery of reputed approved make. Input pf >0.9, with external input isolation transformer, with IGBT/MOSFET rectifier and inverter Double conversion technology, with input voltage range 190-250V @ full load, 50Hz Single Phase, output 230V, 50Hz Single phase, compatibility etc. Output Voltage THDu <6% Full Non-Linear Load According to IEC/EN62040-3including all accessories, frequency regulation 50Hz±0.01%, SMF batteries VRLA type with powder coated CRCA cabinet including all accessories such mounting case, cabling etc as required complete having following specification. The UPS system consist of one numbers of UPS unit and one set of battery bank .
Design, Fabrication, Supply, Testing & Commissioning of PUMP PANEL -A Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame: 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar: 80 Amps TPN aluminium bus bar Earth Bus: 25 x 3 mm Copper busbar Incomer: 80Amps 4Pole MCB -1 No Meters & Indications: Red, Yellow and Blue Indication Lamps 3nos, 2A Control fuses - 1set., 2Amps SP MCB -3 Nos, Outgoing 1, 2 : 2 set, 16Amps 3 Pole MCB -1 No, 2 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 3 : 1 set 16Amps DP MCB -1 No, 0.33 KW DOL starter set -1 No, On off Trip Indication lamps -1 set, Outgoing 4 : 1 set, 16Amps 3 P MCB -1 No, 3.37 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 5 : 1 set 20Amps 3 P MCB -1 No, 3.37 KW DOL starter set -1 No, On off Trip Indication lamps -1 set, Outgoing 6 , 7: 2 set 20Amps D P MCB -1 No, 0.99 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 8,9,10, 11 : 4 set 32Amps TP MCB -1 No, 2.02 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 12 : 1 set 16Amps DP MCB -1 No, 0.33 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 13 : 1 set 32Amps 4P MCB -1 No, 6.75 KW DOL starter set -1 No, On off Trip Indication lamps -1 set
Design, Fabrication, Supply, Testing & Commissioning of PUMP PANEL -B Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame: 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar: 63Amps TPN aluminium bus bar Earth Bus: 25 x 3 mm Copper busbar Incomer: 63Amps 4Pole MCB -1 No Meters & Indications: Red, Yellow and Blue Indication Lamps 3nos, 2A Control fuses - 1set., 2Amps SP MCB -3 Nos, Outgoing 1, 2,4 : 3 set, 16Amps 3 Pole MCB -1 No, 2 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 3 : 1 set 16Amps DP MCB -1 No, 2 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 5 : 1 set 20Amps 3 P MCB -1 No, 3.37 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 6 : 1 set 20Amps DP MCB -1 No, 3.37 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 7 :1 set 20Amps D P MCB -1 No, DOL starter Provision -1 No, On off Trip Indication lamps -1 set Outgoing 8 : 1 set 32Amps TP MCB -1 No, DOL starter Provision -1 No, On off Trip Indication lamps -1 set
Design, Fabrication, Supply, Testing & Commissioning of HOT WATER PUMP PANEL Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame: 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar: 63Amps TPN aluminium bus bar Earth Bus: 25 x 3 mm Copper busbar Incomer: 63Amps 4Pole MCB -1 No Meters & Indications: Red, Yellow and Blue Indication Lamps 3nos, 2A Control fuses - 1set., 2Amps SP MCB -3 Nos Outgoing 1, 2 : 2 set 16Amps 3 Pole MCB -1 No, 0.99 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 3, 4 : 2 set 16Amps DP MCB -1 No, 2.02 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 5,6,7 :3 set (Spare ) 20Amps 3 P MCB -1 No, DOL starter Provision -1 No, On off Trip Indication lamps -1 set Outgoing 8,9 : 2 set 32Amps 4 P MCB -1 No, 7.47 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 10,11 : 2 set 16Amps 4 Pole MCB -1 No, Supply and Fabrication charges
Design, Fabrication, Supply, Testing & Commissioning of FIRE PANEL Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame: 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar: 160Amps TPN aluminium bus bar Earth Bus: 25 x 3 mm Copper busbar Incomer: 160Amps 4Pole 36kA MCCB with spreader and handle -1 No Meters & Indications: Red, Yellow and Blue Indication Lamps 3nos, 2A Control fuses - 1set., 2Amps SP MCB -3 Nos, 0-500V Voltmeter -1 No., 0-200Amps Ammeter with 200/5Amps CTs -3 Nos Outgoing 1 : 1 set 63Amps 4Pole 36kA MCCB with spreader and handle -1 No, Outgoing 2 : 1 set 100Amps TPN 36kA MCCB with spreader and handle -1 No, 50 HP Star Delta Starter set -1 No, 0-100Amps Ammeter -3 Nos, On off Trip Indication lamps -1 set Outgoing 3 : 1 set 63Amps TPN 36kA MCCB with spreader and handle -1 No, 15 HP Star Delta Starter set -1 No, 0-63Amps Ammeter -3 Nos
Design, Fabrication, Supply, Testing & Commissioning of SWIMMING POOL PANEL (A BLOCK) Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame: 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar: 32Amps TPN aluminium bus bar Earth Bus: 25 x 3 mm Copper busbar Incomer: 32Amps 4Pole MCB -1 No Meters & Indications: Red, Yellow and Blue Indication Lamps 3nos, 2A Control fuses - 1set., 2Amps SP MCB -3 Nos Outgoing 1, 2 : 2 set 16Amps 3 Pole MCB -1 No, 2 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 3, 4 : 2 set 16Amps DP MCB -1 No, 0.75 KW DOL starter set -1 No, On off Trip Indication lamps -1 set Outgoing 5 : 1 set 20Amps DP MCB -1 No, 0.75 KW DOL starter set -1 No Outgoing 6, 7 : 2 set 16Amps DP MCB -1 No
Design, Fabrication, Supply, Testing & Commissioning of METERING PANEL-1 Fabricated out of 16 SWG CRCA Sheet top side cable entry for incoming and outgoing feeders. Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 200Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer - : 200Amps 4 Pole 36kA Thermal Magnetic Based MCCB with spreader and handle -1 No. Meters & Indications: Red, Yellow and Blue Indication Lamps 3nos, 2A Control fuses - 1set. 2Amps SP MCB -3 Nos Outgoing 1 & 8 : 8 set 32Amps 2Pole MCB -1 No. 3 Phase KWH Metering Provision -1 No. 32Amps Backlite fuse with Suitable of HRC Fuses -3 Nos
Design, Fabrication, Supply, Testing & Commissioning of METERING PANEL-2 Fabricated out of 16 SWG CRCA Sheet top side cable entry for incoming and outgoing feeders. Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 160Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer - : 160Amps 4 Pole 36kA Thermal Magnetic Based MCCB with spreader and handle -1 No. Meters & Indications: Red, Yellow and Blue Indication Lamps 3nos, 2A Control fuses - 1set. 2Amps SP MCB -3 Nos Outgoing 1 & 6 : 6 set 32Amps 2Pole MCB -1 No. 3 Phase KWH Metering Provision -1 No. 32Amps Backlite fuse with Suitable of HRC Fuses -3 Nos
Design, Fabrication, Supply, Testing & Commissioning of METERING PANEL-3 Fabricated out of 16 SWG CRCA Sheet top side cable entry for incoming and outgoing feeders. Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 200Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer - : 200Amps 4 Pole 36kA Thermal Magnetic Based MCCB with spreader and handle -1 No. Meters & Indications: Red, Yellow and Blue Indication Lamps 3nos, 2A Control fuses - 1set. 2Amps SP MCB -3 Nos Outgoing 1 & 8 : 8 set 32Amps 2Pole MCB -1 No. 3 Phase KWH Metering Provision -1 No. 32Amps Backlite fuse with Suitable of HRC Fuses -3 Nos
Design, Fabrication, Supply, Testing & Commissioning of SDB-UPS-A Fabricated out of 16 SWG CRCA Sheet top side cable entry for incoming and outgoing feeders. Base frame: 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar: 63Amps TPN aluminium bus bar Earth Bus: 25 x 3 mm Copper busbar Incomer - : 63Amps 4 Pole MCB Isolator -1 No. Meters & Indications: Red, Yellow and Blue Indication Lamps 3nos, 2A Control fuses - 1set., 2Amps SP MCB -3 Nos Outgoing 1 & 5 : 5 set 32Amps 2Pole MCB -1 No.
Design, Fabrication, Supply, Testing & Commissioning of SDB-UPS-M Fabricated out of 16 SWG CRCA Sheet top side cable entry for incoming and outgoing feeders. Base frame: 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar: 63Amps TPN aluminium bus bar Earth Bus: 25 x 3 mm Copper busbar Incomer - : 63Amps 4 Pole MCB Isolator -1 No. Meters & Indications: Red, Yellow and Blue Indication Lamps 3nos, 2A Control fuses - 1set., 2Amps SP MCB -3 Nos Outgoing 1 & 2 : 2 set 32Amps 4Pole MCB -1 No. Outgoing 3,4,5 : 3 set 32Amps DP MCB -1 No.
Design, Fabrication, Supply, Testing & Commissioning of SDB-UPS-B Fabricated out of 16 SWG CRCA Sheet top side cable entry for incoming and outgoing feeders. Base frame: 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar: 63Amps TPN aluminium bus bar Earth Bus: 25 x 3 mm Copper busbar Incomer - : 63Amps 4 Pole MCB Isolator -1 No. Meters & Indications: Red, Yellow and Blue Indication Lamps 3nos, 2A Control fuses - 1set., 2Amps SP MCB -3 Nos Outgoing 1 & 5 : 5 set 32Amps DP MCB -1 No.
Design, Fabrication, Supply, Testing & Commissioning of MDB-LTG-EXTERNAL Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 63 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 63A TPN 25 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 5 Nos. Supply and Fabrication charges
Design, Fabrication, Supply, Testing & Commissioning of SDB-LTG-A Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 80 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 80A TPN 25 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 5 Nos. Supply and Fabrication charges
SDB-LTG-B Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 80 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar 2) Incomer: 80A TPN 25 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 5 Nos. Supply and Fabrication charges
SDB-LTG-M Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 63 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar 2) Incomer: 63A TPN 25 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB with spreader and handle - 4 Nos. Supply and Fabrication charges
SDB-R.POWER-A Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 250 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 250A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing 1 to 5 :5 set 100 A TPN 25 KA Thermal magenetic based MCCB with spreader and handle - 1 No. Supply and Fabrication charges
SDB-R.POWER-B Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 250 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 250A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing 1 to 5 : 5set 100 A TPN 25 KA Thermal magenetic based MCCB with spreader and handle - 1 No. Supply and Fabrication charges
SDB-R.POWER-M Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 250 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 250A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing 1 to 4 : 4set 100 A TPN 25 KA Thermal magenetic based MCCB with spreader and handle - 1 No. Supply and Fabrication charges
SDB-LTG-EXTERNAL Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 63 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 63A TPN 25 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 5 Nos. Supply and Fabrication charges
MDB-AHU Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 160 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 160A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 6 No. Supply and Fabrication charges
SDB-LIFT PANEL-A Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 63 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 63 A 4 Pole MCB - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing 1, 3 : 2 set 40 A DP MCB + 40A 30mA DP ELCB with spreader and handle - 2 Nos. Outgoing 2 : 1 set 40 A 4 P MCB + 40A 300mA 4 P ELCB with spreader and handle - 1 Nos. Supply and Fabrication charges
SDB-LIFT PANEL-B Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 63 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 63 A 4 Pole MCB - 1 No. Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing 1 , 3 :2 set 40 A DP MCB + 40A 30mA DP ELCB with spreader and handle -1 No Outgoing 2 :1 set 40 A 4 P MCB + 40A 300mA 4 P ELCB with spreader and handle - 1 Nos. Supply and Fabrication charges
SDB-LIFT PANEL-M Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 63 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar 2) Incomer: 63 A 4 Pole MCB - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing 1,3, 4 :3 set 40 A DP MCB + 40A 30mA DP ELCB with spreader and handle - 1 NO Outgoing 2,5 : 2 set 40 A 4 P MCB + 40A 300mA 4 P ELCB with spreader and handle - 1 NO Supply and Fabrication charges
SDB-UPS-B Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 63 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar 2) Incomer: 63 A 4 Pole MCB Isolator - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 P MCB - 5 Nos. Supply and Fabrication charges
FEEDER PILLAR-1 ( OUT DOOR) Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 320 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 320A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 3 Nos. 40 A 4 Pole MCB - 3 Nos. 63 A 4 Pole MCB - 2 Nos. Supply and Fabrication charges
FEEDER PILLAR-2 ( OUTDOOR) Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 320 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 320A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 3 Nos. 40 A 4 Pole MCB - 3 Nos. 63 A 4 Pole MCB - 3 Nos.
FEEDER PILLAR-3 ( OUDOOR) Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 320 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 320A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 3 Nos. 40 A 4 Pole MCB - 3 Nos. 63 A 4 Pole MCB - 2 Nos. Supply and Fabrication charges
FEEDER PILLAR-4 ( OUDOOR) Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 320 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 320A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 3 Nos. 40 A 4 Pole MCB - 3 Nos. 63 A 4 Pole MCB - 2 Nos. Supply and Fabrication charges
FEEDER PILLAR-5 ( OUDOOR) Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 320 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 320A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 3 Nos. 40 A 4 Pole MCB - 3 Nos. 63 A 4 Pole MCB - 2 Nos. Supply and Fabrication charges
FEEDER PILLAR-6 ( OUDOOR) Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 320 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 320A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 3 Nos. 40 A 4 Pole MCB - 3 Nos. 63 A 4 Pole MCB - 2 Nos. Supply and Fabrication charges
FEEDER PILLAR-7 ( OUTDOOR) Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 320 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 320A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. 3) Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 3 Nos. 40 A 4 Pole MCB - 3 Nos. 63 A 4 Pole MCB - 2 Nos. Supply and Fabrication charges
FEEDER PILLAR-8 ( OUTDOOR) Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 320 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 320A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 3 Nos. 40 A 4 Pole MCB - 3 Nos. 63 A 4 Pole MCB - 2 Nos.
FEEDER PILLAR-9 ( OUTDOOR) Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 320 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 320A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 3 Nos. 40 A 4 Pole MCB - 3 Nos. 63 A 4 Pole MCB - 2 Nos.
FEEDER PILLAR-10 ( OUTDOOR) Fabricated out of 14/16 SWG CRCA sheet ( 2mm for body, frame and covers ,1.6 mm for internal partitions) with Top/Bottom cable/Busduct entry for incoming and outgoing feeders Base frame 70 X 40 mm MS Black Colour powder coated C Chanel. Bus bar 320 Amps TPN aluminium bus bar Earth Bus 25 x 3 mm Copper busbar Incomer: 320A TPN 36 KA Thermal Magnetic based MCCB with spreader and handle - 1 No. Meters & Indications: Red, Yellow and Blue Indication Lamps- 3 Nos 2Amps SP MCB -3 Nos Outgoing : 32 A 4 Pole MCB - 3 Nos. 40 A 4 Pole MCB - 3 Nos. 63 A 4 Pole MCB - 2 Nos.
C-10 TRANSFORMER 11kV/433v, 630KVA Cast Resin Transformer SITC of Transformer comprising of : 11kV/433V, 630KVA ,50Hz,3phase,Vector Dyn 11 Resin Cast Indoor Transformer with on load tap changer with tapping +5% to -5% in steps of 2.5% with winding temperature indicator and hooter with all standard accessories as per IS 2026/77 Cable box on HT side suitable for 3Cx300sq.mm 11kV A2XFY cable & LT side cable box suitable for 4R x 3.5C x 400 sq.mm LT XLPE Al cable with Transformer Enclosure and all standard fittings and accessories.Painting shall be carried out as per IS 631, impedance of the transformer shall be as per relevant standards.
MISCELLANEOUS SUBSTATION ITEMS/ SAFETY ITEMS Supply and providing ISI marked electrical 1.1 kV grade anti-skid rubber mat as per IS:15652.for the following sizes. 2mx1mx2.5 mm thick
Supply and providing ISI marked electrical 1.1 kV grade anti-skid rubber mat as per IS:15652.for the following sizes. 2mx1mx2mm thick
Providing and fixing Fire bucket -9 Litre with stand
Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
Supply and fixing of First aid box
One Tool kit comprising 1 set of flat spanner (Taparia / Stanley/Jalan ), 1 set of box spanner, 1 no. Hacksaw frame with 10 no. blades, 1 no. large, medium, small screw drivers, 1 no. insulated plier, 1 no. nose plier, 1 no. hand crimping tool upto 16 sq.mm, 1 no. digital multimeter, 1 no. test lamp and 1 no. tester, Screw driver set for all types of screw heads also to be provided,
Shock treatment chart duly mounted on a wooden frame with glass on front as required in 2 languages Hindi & English).
Supply and fixing single line diagram, schematic diagrams etc. of A1 size including lamination etc. as required complete on wall.
HT CABLES, LAYING & TERMINATION Providing and erecting cable and termination kit, heat shrinkable Push on type Densons’/ ‘Raychem’ / Elastimold make suitable for 11 KV XLPE cable 3 core 300 Sq. mm. (b) Indoor type
Providing and erecting cable and termination kit, heat shrinkable Push on type Densons’/ ‘Raychem’ / Elastimold make suitable for 11 KV XLPE cable 3 core 300 Sq. mm. (b) Outoor type
11KV DP STRUCTURE over head line termination DP structures Design, supply, erection, commissioning of 11kV Double pole structure made of Hot dip galvanized MS steel, cross arms, , with AB switch, Lightning/ surge arrester, DO fuse, pin insulators, disc insulators, ACSR conductors, GI earthing conductors connected to pipe earth pits, with necessary stay wires and insulators including civil foundation. all installtion must comply with relevant IS and IEC standards. approvals from local utility service providers, 2 Nos of 3 mtr deep pipe earthing with relevant standards
C-11 LIGHTNING ARRESTER SYSTEM
C-12 Gas & Vaccum COPEER PIPING Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-0 tubular insulation/with Class-0 closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc with necessary refrigerant joint as required : 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation
22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation
Vaccum Pump (3HP) with inbuilt Vaccum Tank
Vaccum Pump (5HP) with inbuilt Vaccum Tank
Gas outlet and Collection Jar
Supply, Installation, Testing & Commissioning of LPG High Pressure Click on Adaptors 25.6 mm
Supply, Installation, Testing & Commissioning of Non Return Valve 1/2" for Manifold
Supply, Installation, Testing & Commissioning of Suraksha Pigtail 1/2" X 1/2" LH ( F ) 3 Ft
Supply, Installation, Testing & Commissioning of LPG Pressure Gauge 0-60 Psi 4" Dial SS Body
Supply, Installation, Testing & Commissioning of M.S.Pipe SCH-40 Seamless - 25mm (With all fittings Two coated MRF Epoxy Primer & MRF Epoxy Paint)
Supply, Installation, Testing & Commissioning of Ball Valve 15MM
Supply, Installation, Testing & Commissioning of LPG Regulator Adjustable Type REG -2
Supply, Installation, Testing & Commissioning of Suraksha Pigtail 1/2" x 1/2" -5 Ft [Black
Supply, Installation, Testing & Commissioning of Suraksha Pigtail 1/2" x 1/2" -5 Ft [Black] 15mm dia MS Pipe Schedule-40 Seamless.
Supply, Installation, Testing & Commissioning of Clamp 15mm * 30mm [SS 202]
Supply, Installation, Testing & Commissioning of Clamp 15mm * 55mm [SS 202]
Supply, Installation, Testing & Commissioning of Ms Union Joint 15MM
Providing and fixing wash down water closet with concealed cistern including all fittings and accessories like bracket frame, dual slufh face plate etc. (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (A) vitreous China Pattern :(i) in white colour including all accessories and connections. Make: Jaquar, Kohler, Grohe, Cera high end series.
Providing and fixing wsh down water closet with coupled cistern including all fittings and accessories . (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) )(A) vitreous China Pattern :(i) in white colour including all accessories and connections. Make: Jaquar, Kohler, Grohe, Cera high end series.
Providing and fixing under counter washbasin with pillar tap with C.I. or M.S. brackets painted white including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour including all required accessories and connections like bottle trap, waste etc. Make: Jaquar, Kohler, Grohe, Cera high end series.
Providing and fixing Urinal of approved quality including connection with trap and with integrated Automatic flushing system with pre and post flushing 0.75 ltrsper flush, 360mm x 330mm x 740 mm. including all required accessories and connections. Make: Jaquar, Kohler, Grohe, Cera high end series.
Providing and fixing of Urinal Partition of 900mmx450mm, frosted glass with ss hardware fittings and screws.
Providing and fixing C.P. ss towel ring comlete with C.P. brass/ ss brackets fixed to wooden plugs with C.P. brass/ ss screws.
Providing and fixing Kitchen stainless steel sink with C.I/M.S./SS brackets or frame painted white or as per approved by the architect including cutting holes in walls and making good the same including all fittings. (i) 625mm x 445mm x 200mm size. Make: Jayana, Nirali, Carysil high end series.
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore. Make: Jaquar, Kohler, Grohe, Cera high end series.
Supply, installation, testing and commissioning of brass chromium plated 2 way shower diverter, spout & 6 inch dia wall fixed shower 15/20mm including all fittings, accessories and connections. Make: Jaquar, Grohe, Hindware, Kohler, Cera
Supply, installation, testing and commissioning of brass chromium plated Sink Cock including all fittings, accessories and connections. Make: Jaquar, Grohe, Hindware, Kohler, Cera
Providing, Fixing, testing and commissioning of Single Lever Diverter with provision for spout and Over head shower with shower arm, shower rose, wall flange and spout, all accessories etc, complete.Queo - / KOHLER /Grohe Metropole, jaquar OR Equ.
Providing and fixing Angle tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15mm dia. (Make: Hind ware/cera/jaquar/Grohe) including all required ccessories and connections. Make: Jaquar, Kohler, Grohe, Cera high end series.
Providing and Fixing of Stainless Steel Hand Dryer with all required connections and following specifications. Weld-free cover fixed to the base with two safety screws and lock withspecial speedflow key. Aluminium base. Includes silent-blocks to damp mechanical vibrations. Fire resistant plastic UL 94-V0 fan scroll. High-speed motor with safety thermal cut-off.The motor revolutions canbe adjusted manually by the potentiometer. • Aluminium centrifugal double asymmetrical inlet fan wheel. Disconnects automatically after 60 seconds of continuous use. Electronic infrared detection sensor. Adjustable detection by potentiometer(5- 25 cm). Ultra-flat: 10 cm deep (complies with ADA regulations). complete. Make: Jaquar, Kohler, Grohe, Hindware, Cera high end series.
Providing and fixing of bathing accessories set of one pair of soap dish holder, one no. tumbler holder, one no. napkin ring, one no. 600mm glass shelf with all required fittings and accessories.
Supply and installation of Stainless Steel Handwash Liquid Dispenser with all required fittings and accessories. Make: Jaguar/ Kohler/ Grohe/ Cera
WATER SUPPLY Providing, fixing, jointing and testing, heavy quality cast steel / Brass ball valve single/double piece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 25mm diameter. Make:ZOLOTO/VTC/SANT
DRAINAGE Providing, laying and jointing in true line and level 50mm diameter U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (Make: prince/ supreme / astral / finolex)
Providing, laying and jointing in true line and level 75mm diameter U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (Make: prince/ supreme / astral / finolex)
Providing, fixing and testing PVC Deep seal Multi Trap of 110 X 110 mm dia diameter, with necessary distance piece of 75mm dia pipe and 150 x 150mm heavy duty Stain less Steel three piece grating(Anti cocroch), making necessary holes and cutting in Slab/Walls, etc complete as per engineer in charge. (Make: prince/ supreme / astral / finolex)
RAIN WATER DISPOSAL Providing, laying and jointing in true line and level 110 mm diameter U.P.V.C (Type A) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diameter x 149 mm length x 145 mm height at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. Make: Astral, Supreme, Finolex, Prince
SITE DEVELOPMENT- PUMPROOM, PERCOLATION WELL Supply, fixing and jointing of heavy class UPVC puddle flange pipes epoxy coated, 40 mm dia and minimum 400 mm long clear ends outside the RCC surface, and fixed in underground sumps, water tanks etc. complete, with end joints as required with endcaps / plugs complete as per the requirement of E-i-C (Make: Astral, Supreme, Finolex, Prince)
Providing and fixing electronic type level indicator for water tanks mounting in panel with level display, alarm (level low or high), and manual reset for alarm, potential free set point contacts etc. complete with electrical wiring to probes and all accessories complete the work. Provision to connect to the building Automation system or pump controller through a suitable port.(Make: Wilo)
Please Enable Macros to View BoQ information
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 3.20 MB
BOQ_8133.xls
BOQ • 0.66 MB
Download all tender documents and submit your bid