PROVN OF OFFRS TOILET NEAR BLDG NO TN-55 AND GEYSERS UNDER NAGROTA

Amount

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in Soft/ loose soil0.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils.

Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point.

M/L Plain Cement Concrete Type D-2 1:4:8 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete.

M & L For Broken brick bat hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface.

75 mm thick Cement concrete type D 2, 1:4:8 (using 40 mm graded granite stone aggregate) in sub base of flooring/ hard standing.

Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6

M & L brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in cement mortar 1:4 as in half brick thick walls complete as specified and directed.

Reinforced cement concretetc M-25 (design Mix) using 20mm graded stone aggregate as in foundation, plinth beams,footings etc,.

Reinforced cement concretetc M-25 (design Mix) using 20mm graded stone aggregate as in columns.

Reinforced cement concretetc M-25 (design Mix) using 20mm graded stone aggregate as in floor or roof beams

Reinforced Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) for slabs suspended on walls, beams and columns, in floors, roofs, landings and in shelves and the like.

M/L Fair finished flat Form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exceeding 200 mm thick.

Use and waste of formwork for sides of columns.

Use and waste of formwork for foundation beams floor beam roof beam etc as in lintel over 1.5m clear span. for rough finished surfaces

Use and waste of formwork to sides and soffits of floor or roof beam, beam hauchings, girder, bressum-mers, lintels, cantilivers, shelves incl supports, overhangs, etc. Also splay between floors and beams, etc. for rough finished surfaces

M & L TMT bar 10mm dia and over cut to length bend to shape required indd cranking bending spirally for column, hooking ends & binding with and incld mild steel wire (annealed) not less than 0.90mm dia or securing with chips as directed

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups,spacers and binders

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished fair and even without using extra cement.

Preparing newly plastered surfaces of walls and applying three coats of white wash.

M&L rendering 15 mm thick on external surfaces of wall in cement mortar 1:4 all as specified and directed.

M & L preparing new plastered surfaces of walls and applying two coats of cement base paint.

M&L rendering 5 mm thick on internal surfaces of ceiling in cement mortar 1:6 finished even & smooth without using extra cement as specified and directed.

Preparing newly plastered surfaces of ceilings and applying three coats of white wash.

M&L for non skid cereamic coloured tiles 7 to 8mm thick (square/ rectangle) area of each tiles exceeding 0.11 sqm but n. exc.0.18 sqm, in floor etc set and joined in neat cement slurry and pointed in white or .coloured cement to match including 15 mm thick in cement mortar 1:6 screed bed or bedding layer of mortar for laying floor finishes as directed

M&L polished vitrified tiles light shade 10mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exc 0.36 spm in floor etc set and jionted in neat cement slurry and pointed white or coloured cement to match including roughning of concrete surfaces over 15mm thick screed bed in CM 1:4.

M & L glazed, ceramic, coloured tiles of size450x350x7mm thick, on vertical surfaces such as skirting, dados etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles including endering 10 mm thick in cement mortar (1:3) as in bedding layer for laying of tiles in vertical surfaces complete all as specified & directed.as specified and directed.

S & F solid PVC door frames of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified and as directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , panelling of plain colour PVC sheet to be fitted in the MS framewelded/ sealed to the stiles and rails with suitable PVC sheet beading , and jointed together with solvent cement in the frame at site as per specification.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section

S & F 100 mm long medium weight, cold rolled mild steel Butt hinges.

S & F 150mm size extruded aluminium handle cast type anodised all as specified and as directed by Engineer-In-Charge.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes, single socketed in any length with rubber ring joints laid in floors or trenches, etc including necessary excavation & earth work whenever required complete as specified.

S & F 110mm bore PVC (SWR) Soil, waste and vent pipes, single socketed in any length with rubber ring joints laid in floors or trenches, etc including necessary excavation & earth work whenever required complete as specified.

S & F 110 mm bore PVC (SWR) bends any radius.

S & F 75 mm bore PVC (SWR) bends any radius.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required for 110 mm bore pipe as directed.

S&F Vitreous China bowl urinal flat back, size of 375*320*620mm with sensor, white in colour (minimum), with grating and union for discharge pipe with bottle trap complete all as specified and as directed by Engr in charge Make;- Jaguar

S&F Frosted glass urinal partion of size 450*900 with necessary accessories complete all as specified and as directed.

S & F 15 mm bore galvanized steel tubes, medium grade with all fittings complete fixed to walls and ceilings or laid in floors as specified.

S & F 15 mm bore Bip taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

S & F stop valve/ Angle Valve15mm bore cast copper alloy chromonium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S & F PVC connection pipe 15mm size with PTMT nuts of 600 length including fixed.

S&F , 20 mm bore, ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule. complete all as specified and directed.

S&F 500 ltr capacity Rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified.

S&F in repairs vitreous China wash down water closet pan (pedestal pattern) white "P or S Trap" wall Hunge , (Single piece ), Including 10 Ltr Capacity Flushing cistern & flush pipe . Make Jaguar

S&F PVC (SWR) 100mm dia floor trap, plain with grating including jointing with solvent cement.

Surface excavation n.exc 30cm deep and avg 15 cm deep and getting out any type of soil.

M/L 75 thick mm Cement concrete Type B- 1 1:2:4 (using 20 mm graded stone aggregate) in sub base floorring

M&L PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in copings, plinth course, damp proof course, bed blocks, benching, PCC cills and similar items.

M&L Hard core of gauze n.exc 63mm deposited spreaded and leveled in layers n.exc 15cm thick, watered and rolled/rammed to a true surface.

M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment to match the shade of tiles over 20mm thick screed bed in CM 1:4 and 100 mm thick PCC type C-2 1:3:6 as in sub base all as spd and directed

S&F aluminium (powder coated with approved colour) ventilator, partially glazed and partially louvers, outer frame & mullion fabricated with aluminium section of size 82.50 mm x 38.00 mm x 1.50 mm thick (Cat No 20036), half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portion louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti including S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aperture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position. Note:-(i) Section No given above are of Make-Jindal,

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size etc including taking down or and making good of disturbed surface all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021) (b) Vertical Members of shutter Section shall be be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be be of size 150.00 x 44.45 x 3.00 mm (Section No 19596) (e) Bottom Members of shutter Section shall be be of size 150.00 x 44.45 x 3.10 mm (Section No 19584) (f) Glazing clip for securing glass of shutters shall be be of 0.80 mm thick (Section No 19370).Make- Jinal Section,

S&F white vitreous china Table Top wash hand basin, of size-410X910X150mm fixed in granite counter by making suitable size hole, new brackets, 32mm dia brass chromium plated waste coupling, CP botle trap complete all as specified

S & F in repair 15 mm bore Brass CP Basin mixer for mixing hot & cold water screwed down for iron pipe Make :- Jaugar

S&F 15 mm size Angular cock, cast copper alloy (fancy type), chromium plated, screwed for iron pipe or for brass ferrule all as directed.

S&F PTMT single towel Rail of size 600 mm long as specified and directed.

S&F health faucet with 1 meter long easy flex tube in chrome finish & wall hook, complete all as

S&F stainless steel soap dish holder including fixing arrangement complete all as specified and directed.

M & L for granite 20mm thick machine cut beded and jointed with grey cement slurry and and ponted with white cement admixtiure of pigment to match to shade of granite stone including grinding nd polishing including screed bed or bedding layer of mortar 15mm thick of CM 1:4 Complete.

M&L for 10 mm rendering in CM 1:4 including water proofing compound @2% of cement over roof surfaces finished even and smooth without using extra cement complete all as specified Note:- WPC Mesured and Paid Separately.

Supplied only for Integral water proofing compound.

M&L for Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces

M&L for Applying evenly a tack coat of induatrial bitumen 85/25 grade @ 1.2 Kg/Sqm.

M&L for One layer of APP based polymeric membrane of approved manufacturer, 3mm thick, weight not less than 3.50 Kgs per Sqm , reinforced with non woven polyester fabric or weight not less than 150 gms per Sqm . Polymeric membrane shall be taken to a height 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing(Note (i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions (ii) A Minimum overlap of 100 mm and 75 mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instructions (iii) The make of polymeric membrane shall be IWL India Ltd chennai. Ltd or "MOPLY FP" of Texsa India Ltd). NOTE : S&F of APP based polimeric membrane of approved manufacturer will be laid/fixed by authorised person of the same manufacturers units asper relevent IS.

Applying one coat of aluminium paint on top of APP membrane.

S&F 20 Users On site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., with upflow filte including media complete all as specified and as directed.

M&L for Soakage wells 1.2 M dia X 3 M effective depth , excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size complete all as specified and as directed

Supply and install stationary water heater (Geyser) vertical storage type of 50 Ltr capacity electric driven closed vented 5 star marked suitable for operation for single phase 240 volts, inner container made out of stainless steel, 2000 watt, pressure rating 60 N/Sqmm, class-1, 5 star with all necessary fittings, cutting out holes in existing cement concrete/bricks walls built in cement mortar, supply, fixing, grouting new purpose make mild steel bolts with screwed end 8mm dia and 100mm long alongwith one washer and one Hexagonal nut at screwed end for fixing the geyser all as specified and directed including making good the disturbed surface to match with the existing surface and finishes complete including taking down of old unserviceable Geyse and deposited to E/M yard GE Nagrota all as directed by Engr-in-charge. Make: AO SMITH CAT PART NO HSE-HAS-PLUS-RHS,WHITE,OR EQUIVALENT IN RACOLD ETERNO 2, CRYSTAL

Supply and install stationary water heater (Geyser) vertical storage type of 25 Ltr capacity electric driven closed vented 5 star marked suitable for operation for single phase 240 volts, inner container made out of stainless steel, 1500 watt, pressure rating 60 N/Sqmm, class-1, 5 star with all necessary fittings, cutting out holes in existing cement concrete/bricks walls built in cement mortar, supply, fixing, grouting new purpose make mild steel bolts with screwed end 8mm dia and 100mm long alongwith one washer and one Hexagonal nut at screwed end for fixing the geyser all as specified and directed including making good the disturbed surface to match with the existing surface and finishes complete including taking down of old unserviceable Geyse and deposited to E/M yard GE Nagrota all as directed by Engr-in-charge. Make: AO SMITH CAT PART NO :-HEATBOT-SZS-025-DG-SILVER OR EQUIVALENT IN RACOLD ETERNO 2, CRYSTAL

S&F in place of unsv PVC connection of any make with (ISI Mark) having10mm dia, 45 cm long with steel reinforcement suitable for hot water geyser outlet supply with 02 Nos of Unions/ cup shaped cover with washers all as directed by Engr-in-charge. Make- Prayag/Sona/Horizon.

M&L for point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with 3 mm thick plastic laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following;-

(a) One light/fan point controlled by one switch 5 Amp.

S&F switch piano flush type 5 Amps single pole one way complete,

S&F of ceiling rose 3 terminal complete PVC/Polycarbonate isolated boly complete all as specified and directed.

M&L Integrel sleek extruded batten aluminium /CRCA channel fitting with LED 18 watt complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V 50 Hz. MAKE:-HALONEX,WIPRO,PHILLIPS

S&F baton integrated LED channel of 5W, 230V frequency 50/60 Hz integral sleek extruded polycarbonate LED channel with white acrylic cover, Power Factor not less then 0.9 as per MAKE:-HALONEX,WIPRO,PHILLIPS

S&F for lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F for LED bulb 7 watt complete all as specified and directed. MAKE:-HALONEX,WIPRO,PHILLIPS

S&F sheet metal enclosure distribution board SPN 4 way 230 V, 50 Hz Single door with neutral and din rail complete.

S&F MCB SPN 40 Amps 10 KA 230 volts "C" series complete.

S&F MCB single pole 6 to 32 Amps 10 KA 230 volts "C" series complete

Supply and fixing Exhaust fan 300 mm sweep single phase AC 230/240V complete with louvers for wall mounting incl grouting, holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core 23/0.0076 size from ceiling rose to exhaust fan incl cutting of the hole. Make : Cat part No - Ventil Air - DB of Havells or equivalent in approved make

Supply and laying or fixing of cable 1100 volts grade cable PVC insulated aluminium conductor un-armoured of 16 Sqmm 2 core flat or circular, served with inner sheathing of pace tape and overall PVC sheathed in service connection suspended by insulated hangers not more than one Mtr apart including 4 mm dia suspension GI wire, complete all as specified and as directed by Engr-in-Charge.

BHARTI CONSTRUCTIONS

M/S STAR CONSTRUCTIONS

M/s Mohd Ibrahim Khan

J S ENGINEERS

R.K. Works

ASHFAQ AHMED MANHAS

M/S TUFAIL HUSSAIN MANHAS

Bidder Name

BHARTI CONSTRUCTIONS

ASHFAQ AHMED MANHAS

J S ENGINEERS

R.K. Works

M/S TUFAIL HUSSAIN MANHAS

M/S STAR CONSTRUCTIONS

M/s Mohd Ibrahim Khan

Continental Enterprises