ADDN ALTN SPECIAL REPAIR OF JCO OR MD ACCN AT PIRU VIHAR UNDER GE WEST DELHI CANTT-10

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving not exc 15cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and as in kitchen slabs, shelves, chimney and chhajja and overhead water tank of any type etc not other specifically provided for complete all as specified and directed.

Dismantling of brick tiles or terrace tiles single layer laid, bedded and pointed in any type of mortar on roof complete all as specified and directed.

Demolition of mud phuska on roof slabs, any thickness including cleaning of roof surfaces and removing the debris upto the distance exc 1.00 Km but not n.exc 1. 5 Km incl Scraping of old tar felt roof treatment over concrete padding of any thickness etc from roof including finishes or junction or parapet and cleaning the surface complete all as specified and directed.

S & F 100 mm dia UPVC Pipes (SCH 80) in any length fixed to walls including dismantling of old CI pipes any type complete all as specified and directed.

M&L 15mm thick rendering in cement mortar externl surfaces on fair faces of brickwork or concrete surfaces, applied in two layers i.e. 1st layer of 10mm thick rendering in CM (1:6) and 2nd layer (top) of 5mm thick rendering in CM(1:4) mixed with WPC finished even and fair etc complete all as specifies and directed.(Note- WPC shall be measured and paid seperately) Note- Rates of Scaffolding and water proofing compound is included in this item. No extra payment will be done on this account.

M&L for 5mm thick rendering in CM 1:3 on concrete ceiling surfaces and finish even and smooth surface without using extra cement complete all as specifies and directed. Note- Rates of Scaffolding is included in this item. No extra payment will be done on this account.

Taking down wooden/steel chowkhats/door/ window frame including shutter (without taking off shutter from frame) exc 1.5 Sqm and n.exc 4 Sqm each complete all as specified and directed.

Taking down wooden/steel chowkhats/door/ window frame including shutter (without taking off shutter) not exc.1.5 Sqm each complete all as specified and directed.

Taking down shutter of any description exc 1.00 Sqm and not exc 2.00 Sqm complete all as specified and directed.

Taking down shutter of any description not exc 1.00 Sqm complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (incl backing), removing serviceable tiles to store and rubbish off the premises.

Demolition of stone slabs and tiles of any description or thickness in floor or in any position laid bedded and pointed in any mortar complete all as specified and directed.

Demolition of brick work built in cement /lime mortor in any position / situation in walls/parapets complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections all as specified & directed.

All as per item No. 15 here in before, but 80mm bore.

All as per item No. 15 here in before, but 25mm bore.

All as per item No. 15 here in before, but 50mm bore.

Taking down cement plaster of any description on brick stone or concrete walls surfaces incl racking out joints hacking for keys scrubbing down with water etc including removal of all debris out side MOD land from site complete all as spd and directed

M&L for providing plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregates as in roof kerb or mud stops, rounded or chamfered on edges, plinth courses, coping, kneelers, apex stone, kerb water tough and the like including weathering, slightly rounded or chamfered angles and throating as directed) complete including necessary form work all as specified and directed.

M&L Cement Concrete 1:2:4 type B-2 (40mm graded aggreate) 125mm thick as in tank staging , platforms etc finishing cement concrete surface even and smooth without using extra cement all as per specified and directed

M&L for water proofing treatment to roof surface with APP polymeric based water proofing membrane 3mm thick & weighing not less than 3.5 Kg / Sqm of approved make granular finish consisting of a central core of high molecular high density polyethylene film (HMHDPF) & reinforced with non woven polyester matt of min 160 gm/sqm with a thermo fusible finish laid over a coat of hot blown bitumen of 85/25 grade conforming to IS 702 @ 1.2 kg/sqm over a coat of an bitumen primer conforming to IS-3384 @0.4 Ltr/Sqm over prepared roof surfaces, forcing overlap with a propane or a butane gas torch with a overlap of 75mm at sides & 100mm at ends & sealing including applying a coat of cold emulsion bituminous primer complete as per manufacturer's instructions complete all as specified and directed. (Make Super thermolay manufactured by STP Ltd or 'Hyper Plas' (Polyster) manufactured by M/S IWL Ltd or 'Shalipals' (polyster) manufactured by M/S Capital Steels and chemicals Pvt Ltd) Note :- 1. Water proofing treatment shall be got carried out by the manufacturer or their authorised applicator only. 2. Bitumen primer, bitumen and membrane shall be of same make / manufacturer. (ii) The APP Membrane to be inserted in the parapet wall/wall by cutting chases of atleast 65mm X 50mm size& making good in CM 1:3.

M&L for cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) on roof padding with water proofing compound surface finished even and smooth without using extra cement complete all as specified and directed. (Rate of WPC shall be included in unit rate)

Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner incl 15mm thick screed bed in CM 1:4.

M&L for providing RCC 1:2:4 type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and column, floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified & directed.

M&L for TMT bars 6 to 8mm dia cut to length bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified & directed.

M&L for brick work with sub class 'B' brick straight or curved on plan exc. 6 mtr mean radius built in cement mortor 1:6 complete all as specified.

All as per item No. 27 here in before , but half brick thick wall in CM 1:4 .

Supplying and laying of CPVC pipe 20mm dia SDR 11 incl plain CPVC SDR 11 and brass fittings on walls/ceilings or laying in floors including all necessary fittings complete all as specified.

All as per item No. 29 here in before but 25mm bore tubing including necessary fittings of all type.

All as per item No. 29 here in before but 50mm bore tubing including necessary fittings of all type.

S&F Rotational moulded polyethylene water storage tanks of 500ltrs (cylindrical vertical with closed top)white color hoisted and fixed in position incl tank connection and necessary fittings all as specified and directed

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth and making good complete all as specified & directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/columns

All as per item No. 34 here in before but 75mm bore of pipe.

S&F PVC (SWR) bends of 75mm bore with access door complete as specified and directed.

S&F 100mm bore cast iron soil waste or vent pipes in any length with or without ears with cement joints laid in trenches, floors incl cast iron pipes and fittings if lead joint is provided in lieu of cement joint including demolition complete all as specified and directed.

S&F 100mm bore UPVC bends (any radius) diminishing pieces or tapers (larger bore to be measured) with oval access doors.

S&F in repair 100mm dia upvc branch piece/Cross Tee for , soil waste and vent pipe, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches,fitted with oval access door complete all as specified and directed.

S&F upvc Cowl for 100mm bore of CI pipe complete all as specified and directed. .

S&F in repairs 10 ltrs capacity PVC valveless syphonic action type low level flushing cistern complete with syphone handle lever PVC bend including connecting to WC and fixing on walls with bracket complete all as specified.

S&F in repair European vitretious china wash down water closet pedestal pattern pan S Trap (excluding flushing cistern but including flush pipe and pvc seat cover white). Make (Hindware-Cat No 20118 S-18, Cera Cat No S-1053101, AP Royale Cat No –ECS-28-S).

S&F in repairs vitreous china wash hand basin (flat black) white of size 550x400mm excluding taps, waste chain and plug and porcelain stopper including a pair of mild steel angle iron brackets of suitable size complete all as specified.

S&F PVC (SWR) junction single, (Single T) equal or unequal of 75mm bore all as spd and directed.

S&F in repair PVC (SWR) bends 110 mm bore complete all as specified and directed.

S&F mild steel framed work as in door or gates of angle or other sections, cooler stands, with gusset plates rails, braces etc complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and purpose made hinges or steel sheeting or other covering, running rails and guides) and hanging, fastening and fixing complete conforiming to Fe 290 Gde E-165.

S&F Providing and fixing factory made single extruded WPC(Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. Note:- Manufacturers test certificate and screw out test will be provided by the contractor

Supply and fixing 30mm thick FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER conssisting of density 650 Kg/CBM manufactured by an ISO-9001-2015 certified company. Door to be panelled with SS mosquito and XTN aluminium mesh for additional strengh and safety purpose (Confirming as per IS 4020). The door should be water prorf, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 Nos. SS butt hinges size 100mmx25mmx2mm and 33mm long steel screws drilled suitable to pass through other hardwares should be fixed with 19x6mm size steel screws. etc. complete all as specified & directed. Note:- MTC and Screw out test will be provided by contractor.

M&L for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apperture 1.40 mm fixed to door/window frame complete all as specified and directed.

All as per item No. 49 here in before , but fixed in repair complete all as spd and directed..

S&F for PVC (SWR) floor trap of 75mm/110mm dia with grating including jointing with solvent cement complete all as spd and directed.

S&F in repair butt hinges 100mm size, medium weight cold rolled stainless steel and fixed to angle iron /steel chowkhat complete all as specified and directed.

M&L for rendering 10mm thick on top of roof concrete in cement mortar 1:4 with water proofing compound at the rate of 3% by weight of cement to have a smooth surface for laying of waterproffing membrane.(Note- WPC shall be measured and paid seperately).

S&F aluminium anodised barrel tower bolt, extruded section 200mm size complete all as spd and directed..

S&F aluminium anodised Handles for 150mm size complete all as spd and directed..

S&F aluminium anodised Handles for 100mm size complete all as spd and directed..

S&F 300mm aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 100 mm hasp and staple, mild steel stove enamelled black. Including bolt to hinges plate and fixed with screws all as specified and directed.

M&L for Preparation of new or previously untreated surfaces of wood or wooden base surface of any description not otherwise described over 10cm width or grith and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified.

All as per item No. 59 here in before but on steel surfaces over a coat of redoxide primer.

M&L for Preparation of old wooden surfaces of any description not otherwise described over 10cm width or grith and applying one coat of synthetic enamel paint complete all as specified.

All as per item No. 61 here in before but one coat of paint on old steel surfaces.

Complete removal of existing treatment of wall using wire brush/mechanical/ electrical driven sanders, washing, rubbing down and stoping of painted surface including preparation of surface etc and M&L for applying two coats of Oil bound distemper all as specified and directed by Engineer-in-charge.

Complete removal of existing treatment of Ceiling using wire brush/mechanical/ electrical driven sanders, washing, rubbing down and stoping of painted surface including preparation of surface etc and M & L for applying two coats of Oil bound distemper all as specified and directed by Engineer-in-charge.

Complete removal of existing treatment of wall using wire brush/mechanical/ electrical driven sanders, washing, rubbing down and stoping of painted surface including preparation of surface etc and applying two coats of cement based paint all as specified and directed by Engineer-in-charge

M&L for preparation of new plastered surfaces on walls and applying two coats of cement based paint including one coat of alkali resistant primer complete all as specified.

M&L for preparation of new plastered surfaces on wall and applying two coats of oil bound distemper including one coat of alkali resistant primer complete all as specified.

M&L for preparation of new plastered surfaces on ceiling and applying two coats of oil bound distemper including one coat of alkali resistant primer complete all as specified.

M&L for 18-20mm thick, granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like icld 20mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl drilling hole for gas pipe as per the requirement complete all as directed.

M&L for non skid colour ceramic tiles 7-8 mm thick (square/rectangular) area of each tiles exceeding 0.06Sqm but not exceeding 0.11Sqm, in floors etc, set jointed in neat cement slurry & pointed in coloured cement to match and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 600 x 300 x 7-8mm on vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white/ coloured cement, laid over and including backing coat 10mm thick in cement mortar 1:4, complete all as specified.

M&L for jointfree Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile(600x600mm) exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to match and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection 75mm thick laid in bays and surfaces finished even and fair, including filling the joints with bitumen mastic complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia, D type 60 cm long between flanges, complete all as specified and directed.

S&F curtain rod of 25mm dia stainless steel with fixing brackets stops and rollers, finnels etc complete all as specified and directed.

S&F sink made of stainless steel 1mm thick for kitchen with plugs, washers and waste including bedding in cement mortar to dwarf wall or including fixing cantilever, brackets and connecting union to pipe overall size 495 x 420mm, bowl size 410mm x 330mm x 160mm incl waste pipe complete all as specified and directed.

S&F in repair 15mm dia brass chromium plated fancy type bib tap , cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified. Make-prima (cat No-POL -7102) Make-Jaquar (Cat No -107PM) Make-Player (Cat No –PAS-106)

S&F 15mm bore brass CP wall, Sink washbasin mixing hot and cold water crewed down for iron pipe and fixed complete all as specified Wall mixer make (prima cat No- POL-7112, Jaquar Cat No –COP-281PM, Player Cat No –PAS-120). Sink mixer Make (prima cat No –POL-7111, Jaquar Cat No –COP-309PM, Player Cat No PAS123). Basin mixer Make (prima cat No – PSW-6912, Jaquar Cat No COP-001BPM, Player Cat No –QD-1024).

S&F in repairs stop valve 15mm bore fancy type brass chromium plated , with long shank and cup (concealed type) complete all as specified and directed.

S&F in repair 15mm bore stop valves/angle valves brass CP fancy type chromium plated, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe for unions and fixed completed all as spd and directed. Make(Prima-Cat No-PAR 7004, Jaquar-Cat No -057PM, Player Cat No PAS-109).

S&F in repairs 20mm bore of Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F PVC connection 600mm long with 2 Nos brass check nuts, suitable for 15mm bore complete all as specified and directed.

S&F in repair ball valve of 25mm dia for CPVC pipes complete all as spd and directed

S&F in repairs shower rose, chromium plated brass, fancy type, 125 mm with or without swivel joint, any size, including fixing to steel pipe or union, complete all as directed.

S&F factory made 18mm thick 100% solid WPC(Wood Polymer Composite) laminated board of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. Note:- Manufacturers test certificate and screw out test will be provided by the contractor

M&L for machine cut Kota stone slab 20 to 25 mm thick as in window cill, treads, risers of staicase laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including cement screed bed 20 mm thick in cement mortar 1:6 complete all as specified and directed.

M&L for grinding & polishing of existing kota stone floor surfaces all as specified and directed

S&F stainless steel kitchen plate rack made out of stainless steel sheets 1mm thick overall size 600mm x 750mm x 250mm including complete all as specificed and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screwshaving minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames,minus 5mm tolerance indimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Providing and fixing factory made single extruded WPC(Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. Note:- Manufacturers test certificate and screw out test will be provided by the contractor

S&F factory made 18mm thick 100% solid WPC(Wood Polymer Composite) laminated board of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. Note:- Manufacturers test certificate and screw out test will be provided by the contractor

S&F of SS auto closing hinges openable at 0 degree for kitchen cabinet shutters and bed room cub boards complete all as specified.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of of brass polished bright finished complete all as specified.

S&F ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed complete all as specified.

S&F framed work such as grills, grating etc. with ends of bars shouldered and /or riveted , or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar works conforming to Fe290. Gde-E-165 complete all as spd & directed. Note : Provision of openable arrangement for placing coolers on stand shall be made in window grill wherever required.

S&F for steel windows/ventilators fabricated from roll formed section made of galvanized steel color coated powder coated ( base steel as per sqm IS-513 D quality galvanized as IS 277 with zinc coating of 120 GSM with total coated thickness of 0.60mm. The coated section shall be with primer coated of primer of -7 microns thick, finish painted with a polyster paint of 12.16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure plyster powder upto 50-60microns thick with the following specifications (a) Main frame 72mm x 55mm x 0.58mm (b) Mullion 72mmx50mmx0.58mm (c) Glazed/gauzed shutter frame 47mmx20.20mmx0.58mm (d) Glass beats beads size 12mm x 12mmx0.58mm Accessories. Easch shutter shall be provide the following fiting (a) Stainless steel pipe of hinges 01 set (b) Alumminium powder coated handle -04 Nos. Glass panes Glazes shutter and fixed glass of 5.00mm thick float glass. WIRE MESH -Stainless stell wire mesh of 0.3 mmnomonal dia wire and average width of aperature 1.40mm. Grills window shall be provide with grill made of 10mm square MS bars welded to 12mmx6mm thick MS plate. Distance between bars should no be more than 12cm c/c. Total grill unit shall be enamel painted and fixed to window frame screw. Note: The glazes/ Guaged shutter includingguard bars shall be measure once i.e as per area of opning. No seprate payment of seprate shutter i.e. Glazed and fly proof and guard bars shall be made. Area of shutter shall be the area of opening. The rate quoted by the contracter is deemed to inclusive of all specified in Drg No- CEDZ/TD/289 sheet 1 R/2 and 2R/2.

Supply only integral water proofing compound (ISI marked) complete all as spd & directed .

S&F aluminium anodised barrel tower bolt, extruded section 100mm size complete all as spd & directed.

Taking down wooden door shutter exc 1.00 Sqm and n. exc 2.00 Sqm each and refixing in same opening after repair complete all as specified and directed

Supply only CP waste coupling 32mm size with PVC waste pipe, plugs and washers for kitchen sink complete all as spd & directed.

S&F of floor door stopper of alumimium alloy body and tongue, anodised, with hard drawn steel spring including vulcanised rubber piece of 140mm long

M&L for followings :-(i) Removing plaster & finishes from all exposed / damaged portion of coloumns, slabs & beams(ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible)(iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed)(iv) Cleaning exposed concrete substrate by using water jet.(v) Removing visible rust along the length of reinforcement using hand tools as approved.(The Engr-in-charge may order sand blasting if rust is approved)(vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

M&L for providing rust proof /anti corrosive treatment to bars :-(i) cleaning of all exposed bars (new & old) alround(ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer(iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris and dust (ii) Applying Epoxy bond coat on the sound substrate using approved apray machine & ensuring that no pin holes are visible (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitoius mortar) of 25-50mm thickness. Note : Application of PMM sghall of preferably be in coats of approx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed within 30mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufacturer cmplete all as specified and directed.

M&L for treatement of cracks found in the core concrete :-(i) Opening of crack by making a ' V' notch/groove of size 12mm x 12mm over the entire length of the crack as identified by the Engr-in-charge.(ii) cleaning ' v' notch/groove of all dust/debris/loose material(iii) Drilling hole of 16mm dia and about 40mm deep along the length of crack @ (300 mm c/c or thickness of structural member whichever is less)Note : In case length of crack is found less than 300 mm then min 2 holes shall be drilled.(iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole drilled above and fixing the nipple with the help of fast setting epoxy putty. (v) seal the surface around the nipple and the area of crack between successive nipples polymer modified mortar to ensure that there is no leakage from any gap.(vi) Allow the polymer modified mortar to cure for 24 hours and ensure that firmly fixed in postion.(vii) cleaning nipple one by one commencin from the top to bottom in case of column and one by one in alternate direction incase of beam/slab using blow compressed air followed by water injection. An Ensuring that there is no obstruction in free flow of grouting materials complete all as specified and directed.

M&L for treatement of core concrete when found to be porous/honeycombed :-(i) Marking the area in marker as directed by the Engr-in-charge.(ii) Drilling holes of 16mm dia in an orthogonal grid on exposed cone of member @ 150 mm c/c both way, depth of the hole shall be about 60% of the element thickness.(iii) clean the drill hole using compressed air removing the dust/dirt.(iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole with the annular space around the nipple sealed with epoxy putty. It shall be ensured that the injected grount does not leak.(v) Allow the nipple to cure for 24 hours.(vi) Injecting " Resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin.Note : pressure shall be in the range of 2-3 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly.

M&L for chequered cement concrete tiles 30 cm x 30cm x 25mm thick with gray cement and pigment incl 50mm thick cement concrete 1:2:4 type B2 using 40mm graded aggregated as in sub base under floor all as specified and directed. incl demolition of cement concrete(unreinforced) in ground floors and paving n exc 15cm thickness (below or above ground level complete all as specified and directed.

M&L Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard andrailing 60cm long all as spd and directed

M&L for machine pressed precast concrete glossy finish interlocking paver block. any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade laid over 25mm thick sand cushion complete all as specified and directed. (Note : Sand filling to be measured and paid seperately)

M&L for sand filling under floors for cushion bed to interlocking paver block all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screwshaving minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames,minus 5mm tolerance indimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screwshaving minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames,minus 5mm tolerance indimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Stack clamps made out of 50mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm dia pipe complete all as spd and directed.

S&F Grating doom 125 mm dia with waste hole of SS (min wt 50gm) all as spd and directed by Engg-in-Charge.

S&F Grating doom 100mm dia of SS (Minimum weight 35gms) all as spd and directed by Engg-in-Charge

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping with fair finished surface of concrete) all as spd and directed

M&L rendering 10mm thick in CM 1:6 on internal surfaces of any description, and finishing the surfaces even and fair without using extra cement complete all as spd and directed.

Description of Work / Item(s)

Amount

Taking down carefully copper/aluminium any type of point wiring (light/fan/socket /power) complete (fittings such as switches, ceiling roses, holders, sockets,regulators light fittings) and making good the disturbed surfaces of wall/floors/ceiling etc) complete all as specfied & directed.

Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including non-metalic rigid PVC conduit concealed in wall/fixed to roof/truss/columns etc and existing provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor, fabricated branded modular metal flush box concealed in walls with suitable modular inner and outer plate for housing modular switches, socket outlet and fan regulators etc , all as specified and directed for the followings:-

(a) One light/fan/bell point controlled by one way switch 5 amps.

(b) One 3 pin 5 Amps socket outlet point controlled by one way switch on independent board.

(c) One 3 pin 5 Amps socket outlet point controlled by one way switch on same board.

All as per above item No 2. but with cable 2.5 Sqmm size 1100 volts grade for One 3 Pin socket 15A Independent board

Supply and fix switch modular type single pole one way 6 Amps complete all specified and as directed.

Supply and fix modular switch 16 Amps one module single pole one way complete all specified and as directed..

Supply and fix modular socket 5 pin multi purpose 6 Amps flush type complete all specified and as directed. .

Supply and fix modular socket multi purpose 2-in-1, 6 pin 6/16 Amps 2 module complete all specified and as directed..

Supply and fix modular ceiling fan regulator , step type for BLDC ceiling fan of suitable capacity and module complete all as specified and directed complete all specified and as directed..

Supply and fix switch modular type single pole bell push 6 Amps complete all specified and as directed..

S&F bell ding dong AC,230 volts,single pole complete all specified and as directed. .

Taking down ceiling fan, sealing cable end, dismantling blades and removing fan and blades and deposit to MES store to store complete all as specified and directed.

Supply & fixing of ceiling fans complete with blades, down rod, 230 volt, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC).

S&F of factory made epoxy polyester powder coated distribution board SP & N 8 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 6 SP MCBs as outgoings including taking down old unsv DB's & MCB's complete all as specified and conforming to IS: 8623 alongwith cable end box for above DB all as specified and directed. NOTE (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F of single pole MCB 6 to 32/40 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 including taking down old MCB's complete all as specified and directed.

S&F of SPN MCB 32 amp, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘C’ curve, 10 KA breaking capacity, complete all as specified and directed.

Supply and fix LED batten luminaire surface mounted, extruded aluminium body & PC diffuser 4 feet system wattage of 20 Watts with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 10%, colour temperature - 6500K, surge protection 2.5KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC, system efficacy at luminarie level > 120 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete.

Supply and fix 35 W High efficient LED Building security light fitting with pressure die cast LM6 Aluminum housing and has lenses specially designed for security Lighting with polycarbonate cover. System level efficacy of the luminary level ≥ 110 Lumens/watt with a life class of 50,000 burning hours at L70. The color temperature is around 6500 K with a color rendering index of 70. The luminaire is IP:66 protected with IK05 impact resistance. It has an electronic driver complaint to IEC safety standards with a power factor>.0.9, voltage variation range 120-270V, THD<20%, High and low protection along with a surge protection of 4 KV including provision of 40mm dia GI light grade pipe1.5 meter length bend to shape and necessary clamps etc for fixing the light fittings on bldg fixed complete

Supply and fix LED batten luminaire surface mounted extruded aluminium body & PC diffuser 2 feet system wattage of 10 watts and not less than 900 lm system lumen output with life time of 50000 burning hours with 70% of its initial lumen maintained. CRI > 80, power factor > 0.95, THD < 10%, color temperature > 6500 K , surge protection 2.5 KV in CM IP- 20 protected meets LED IS specifications, short circuit and over circuit protection, voltage range - 150 to 270 volts AC, temperature range 0 to 50 Degree C, system efficacy at luminarie level > 100 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete.

Supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230 V, 50 Hz, RPM 1200, copper winding of sweep 300 mm complete all as directed and specified.

Taking down exhaust fan of 300 mm sweep and deposit to MES store yard and refixing the same after cleaning with suitable nuts and bolts as per requirement complete all as specified and directed.

Supply and fixing of lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fix 10 watts bulkhead fitting including LED bulb 10 watts with powder coated die cast aluminium housing/poly carbonate with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary is > 100 lm/W with a life class of 50,000 burning hours at L70 criteria, Power Factor >0.95, driver with Voltage range 150-270V, Temperature range 0 to 50 Deg, Driver efficiency >85%, THD<10%, CRI>80, Color Temperature-6500K, Surge protection of 4.0 KV, including connecting up with necessary PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete.

S&F ceiling rose 3 phase/PVC/polycarbonate isolated body complete all as specified and directed.

S&F single pole and neutral enclosure with a two pin earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and directed.

S&F in repair PVC conduit with Tee,Bends,nut,screw,clamp,connected items be concealed in wall during plastering work for any damag portions where required complete all as specified and as directed

M&L far Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, burieddirectly in ground (earth pit not lessthan 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion all as specified and directed.

Adhunik Builders (BID ID -3232899)

Shivom Projects Private limited (BID ID -3233316)

imran construction company (BID ID -3233232)

Third Wave Services Pvt Ltd (BID ID -3232897)

ASSOCIATED CONSTRUCTION CO. (BID ID -3233089)

MOUNIKA ENTERPRISES (BID ID -3233221)

V r traders (BID ID -3233095)

M/S Yamin (BID ID -3231678)

V r traders (BID ID -3233095)

ASSOCIATED CONSTRUCTION CO. (BID ID -3233089)

L G BUILDERS (BID ID -3233396)

Shivom Projects Private limited (BID ID -3233316)

Third Wave Services Pvt Ltd (BID ID -3232897)

MOUNIKA ENTERPRISES (BID ID -3233221)

imran construction company (BID ID -3233232)

M/S Yamin (BID ID -3231678)