8768 REPAIR MAINT OF LT DISTRIBUTION SYSTEM SWITCH GEAR LT PANELS LT CABLE AND ALLIED WORKS AT OLD CHSC RF LINES 4 RMC QTRS ALC QTRS EME QTRS MD LINES AND CONNECTED AREA UNDER AGE EM II OF GE SOUTH PUNE

Amount

Excavating in trenches n. exc 1.5m wide and not exc. 1.5m in depth for foundation of poles, laying UG cables, etc and getting out in soft/loose soil complete as specified and directed.

Removing excavated material not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point in soft / loose soil complete all as specified and directed.

Returning filling including spreading levelling, watering and well ramming in layers not exceeding 25cm in soft/loose soil complete all as specified and directed.

M&L for boring / drilling by machines/manual horizontally under the road in any type of soil without cuttiing / disturbing the existing road and inserting GI pipe of any size for drawing the cable complete all as specified and directed. Note:- GI pipe shall be measured and paid seperately.

M&L for laying double wall corrugated HDPE pipe, UV stabilized of size 120X103 mm (ODX ID), IS-16205 for cable protection laid in trenches or fixed to walls complete all as specified and as directed.

M&L for galvanised steel tube 50mm bore (light grade) laying in road / drain crossing for cable protection pipe complete all as specified and as directed.

M&L for galvanised steel tube 50mm bore (light grade) fixed to pole / wall / floor for cable protection pipe including clamp of MS flat of size 50x5mm and nut, bolt & washers of size 50x12mm for clamping of cable protection pipe with wall / pole as where required complete all as specified and as directed.

M&L for PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation filling & mass concrete for sub base of poles complete all as specified and directed.

M&L for cement concrete 1:3:6, type C-2, (using 40 mm graded stone aggregate) for foundation of poles, stays, etc including form work as required /ordered complete all as specified and directed.

M&L for cement concrete 1:3:6 type C1 (using 20 mm graded stone aggregate) as in coping of poles, padestal, etc including necessary form work etc complete as specified and directed.

Excavation in post holes (or similar holes) each not exc 0.5 cum getting out , returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard / dense soil complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 10 sqmm 2 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 10 sqmm 4 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 16 sqmm 2 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 16 sqmm 4 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 25 sqmm 3.5 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 35 sqmm 3.5 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 50 sqmm 3.5 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 70 sqmm 3.5 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 95 sqmm 3.5 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 120 sqmm 3.5 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 150 sqmm 3.5 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 185 sqmm 3.5 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables having cross-sectional area 240 sqmm 3.5 core with aluminium conductor 1100 volts grade including porviding lugs as required complete all as specified and directed.

Dismantling /uprooting of LT unserviceable pre-stressed concrete/steel poles of any size and length including taking out dismantled portion of poles embeded in concrete after necessary demolition of concrete foundation and complete all as disposal there of as directed by the Engineer-in-Charge.

Supply, fixing and errecting in true vertical position of steel tubular pole 9 mtr long with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP-22, including painting with anti corrosive black bituminous paint internally complete and externally up to planting depth and exposed portion with Aluminium paint two coats over a coat of red oxide primer including taking down of old unserviceable / damaged pole complete all as specified and directed by Engr-in-charge. (Note : Excavation and earth work, PCC for foundation and coping shall be measured and paid seperately under respective item of BOQ)

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6mm thick, burried directly in ground (earth pit not less then 2.25m deep bellow ground level) with top edge of the plate not less then 1.5m deep below normal ground level connected to galvanised iron strip of 32 x 6mm earth lead by means of bolt, nuts, washers of galvanised steel earth strip protected by and including GI pipe 40 mm dia bore (light grade) and conncted to main test point as directed and including concrete pit in PCC (1:3:6) type C-1 precast RCC (1:1.5:3) type A-1 cover slab 54 x 5 cm reinforced with 4mm dia TMT bars @ 150 mm c/c both ways with one handle for lifting made out of 8mm dia TMT bar embedded in precast cover slab funnel wire mens 20mm bore GI pipe (medium grade) for watering charcoal and salt in altemate layers, including necessary excavation and earth work in any type of soil complete all as shown on electrical plate No3 of SSR Part-I complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600X600X6 mm thick buried directly in ground preferably vertically in ground with top edge not less than 1.25 mtr deep below normal ground level connected with and including galvanised iron wire 4 mm dia as earthing lead by means of nuts bolts and washers of galvanized iron protected by 15mm dia (medium grade) GI tubing, funnel, wire mesh, 20 mm bore GI tubing (light grade) watering pipe , including concrete pit in PCC (1:3:6) type C-1, precast RCC (1:2:4) type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT bars @ 15cm c/c in both ways and 10mm dia MS handle (01 No) of suitable size, charcoal and salt in alternate layers necessary excavation and earth work in soft/loose soil all as shown in Electric plate No. 3 of SSR Part-I and testing on completion complete all as specified and as directed.

Supply,install, commission and testing cubical type LT panel board ,outdoor canopy type, manufactured by a CPRI approved factory, floor mounted, dust & vermin proof,front and rear operated door with necessary locking arrangement made of 50 x 6mm MS angle iron frame work and CRCA sheet of 3.0 mm thick duly painted with two coats of powder coated paint of approved shade after seven tank treatment process both internally and externally. The panel shall be suitable for 415 Volts, 50 HZ, 3 Phase 4 wire system and shall be complete with suitable capacity copper bus bar (1.5 times the incoming switch gear current rating) with suitable size of PVC insulated copper conductor, thimbles glands complete all as specified and directed by Engr-in-Charge with the following accessories :- INCOMING (a) MCCB 4 pole, 415 Volts, 400 Amps, 36 KA - 01 No. OUTGOING (a) MCCB 4 pole, 415 Volts, 200 Amps, 25 KA -02 Nos (b) MCCB 4 pole, 415 Volts, 125 Amps,16 KA -01 Nos (c) MCCB 4 pole, 415 Volts, 63 Amps,10 KA -01 Nos (d) Digital VAF meter for basic electric system monitoring-01 Nos. (e) Indicator lamp (RYB) (set of three) - 01 Set

All as per Item No 29 above here in before but with the following accessories complete all as specified and directed by Engr-in-Charge:- INCOMING (a) MCCB 4 pole, 415 Volts, 200 Amps, 25 KA - 01 No. OUTGOING (a) MCCB 4 pole, 415 Volts, 63 Amps,10 KA -04 No. (b) MCB TPN , 415 Volts, 32 Amps, -02 Nos (spare) (c) Digital VAF meter for basic electric system monitoring-01 Nos (d) Indicator lamp (RYB) (set of three) - 01 Set

S&F in repair TPN copper bus bar box, outdoor type of 200 A capacity mounted on porcelain bridge insulator for one incoming cable and 4 out going cable, housing in sheet metal enclosure of MS sheet 3.0 mm thick CRCA sheet and angle iron 40x40x6 mm frame, painted with two coats including arrangement for cable gland for incoming and outgoing cables, locking arrangement, suitable foundation/platform for mounting the FPB with space for and including with the switch gears i.e. MCCB 100 Amps, FP, 10 KA (for incoming control) complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old painted surface above the planting depth and PCC coping of steel tubular LT pole of 09.00 metre length including MS clamps ,cable protection pipe bracket fitted with street light fittings etc by scraping with steel wire brush and applying two coats, of aluminium paint to external surface of poles MS cross arms MS clamp, cable protection pipe etc to give even shade including Zebra colour of painting from 1.5 mtr height from the top of coping/ bottom of pole as per site condition and numbering of poles complete all as specified and as directed by Engr-in–charge Note: Zebra colour will be applied by synthetic enamel paint of black/yellow colour as approved in alternate layer of 30 cm height of each layer, complete all as specified and directed by Engr-in-Charge

Supply and fix in repair energy efficient LED street light fitting of 45 watt made up of pressure die cast aluminium housing with toughened glass and high power LEDS with secondary optics, efficacy 110/120 LPW, IP 66 protection aerodynamically designed for all weather conditions with efficient thermal management including 10 KV SPD complete all as directed by Engineer in Charge. Model: ENDURA SUNBEAM Cat No : ENDURASUNBEAMSL45WLED757SASYTOPC of Make HAVELLS or equivalent model of Halonix, Bajaj, Wipro, Crompton

Supply and fix in repairs energy efficient LED street light fitting of 60 watt made up of pressure die cast aluminium housing with toughened glass and high power LEDS with secondary optics, efficacy 110/120 LPW, IP 66 protection aerodynamically designed for all weather conditions with efficient thermal management including 10 KV SPD complete all as directed by Engineer in Charge. Model: ENDURA SUNBEAM Cat No : ENDURASUNBEAMSL60WLED757SASYTOPC of Make HAVELLS or equivalent model of Halonix, Bajaj, Wipro, Crompton

S&F in repairs of LT service cable 6 sqmm 2 core inside PVC conduit 20 mm dia medium grade for landscape lighting/ garden lighting inside trench or on wall / floor complete all as specified and as directed. Note: The rate quoted must be inclusive of laying the cables in trench at max 10 cm depth or mounting on floor/wall

S&F in repair Integral compact wide beam LED flood light luminiaire with die cast aluminium alloy housing with IP 66 protection, tampered protective toughened glass 5mm thick, thermal shock impact resistant cover, epoxy black powder coated finish, high purity pre-anodised specular aluminium sheet reflector, with silver painted contacts suitable for 1x100 Watts LED and connection with two runs of 2.5 Sqmm multi-stranded, copper flexible wire including taking down old unserviceable one and testing complete as specified and as directed by the Engineer-in-Charge. Model: HLFLD-ML17-100-CW-R01 of Halonix or equivalent in Wipro / Crompton / Bajaj / Havells

S&F in repairs of LED post top lantern of 45 W, IP 65 protection with in built electronic driver and aluminium housing in pure polyster UV resistant powder coated black finish, top maintainable product with top opening die cast cover , anti corrossive stainless steel screws & silicon gasket, HET PMMA diffuser conforming to IS 10322 Part 5/Sec 1: 1987, suitable for pole diameter up to 75 mm , cable entry through pole from bottom, 3 way 10 Amps GFP mains connector duly wired upto terminal block complete all as specified and as directed. Make- Halonix Cat part No: HLPT-04-45-CW or equivalent in Bajaj, Crompton, Havells, Wipro

S&F in repairs of GI pipe bracket for street light fittings made out of 32 mm dia GI pipe light grade 1.5 mtr long bent to required angle/ shape with and including necessary clamps, nuts, bolts, & washers of suitable size all as directed by Engineer - in - Charge

S&F in repairs of PVC weather proof loop-in loop-out box with 4 pole terminal block mounted on porcelain or bakelite and MCB SP 06 Amps for controlling including necessary clamps for mounting on pole etc complete all as specified and directed. Make: Sintex Cat Part No-GSJB 2014 or techno commercially equivalent.

M & L for testing and fault locating of LT underground cable with the help of cable fault locating machine at site complete all as specified and directed by Engineer In charge. Note:- The quoted rate shall be deemed to be included the cost of transportaion of machine to and from site and any rental charges for the machine. Locating of faults at one site will be measured as one Job irrespective of the number of faults. Rectification of fault will be measured and paid separately under relevant items seperately

Supply, jointing and testing in repair cable jointing kit for 1.1 KV grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 25-50 Sqmm complete all as specified and directed.

Supply, jointing and testing in repair cable jointing kit for 1.1 KV grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 70-150 Sqmm complete all as specified and directed.

Supply, jointing and testing in repair cable jointing kit for 1.1 KV grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 25-50 Sqmm complete all as specified and directed.

Supply, jointing and testing in repair cable jointing kit for 1.1 KV grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 70-150 Sqmm complete all as specified and directed.

M & L for preparation of old painted steel or iron surfaces of existing L:T panel by scrapping with steel wire brush/scrapper emery paper etc and applying two coats of synthetic enamel smoke grey paint over a coat of red oxide primer (painting shall be done by spray machine) including writing of incoming and outoing details etc. at prominent place/location of LT panel with black synthetic enamel thick paint in white back ground complete all as specified and directed Note: Necessary shut down of power supply shall be obtained from the Engr-in-Charge by the contractor before proceeding the work, also electric supply should be restored as early as possible after completion of the work.

M & L for repair to LT panel door (inner and outdoor) by replacing the damaged hinges or welding the existing hinges, door locks, replacing the missing nuts, bolts & washers etc. tightening the cable glands, cable lugs, applying kuchha rubber strips onto the damaged insulation of cables, to prevent any short circuit / earth leakage , including cleaning the LT panel with compressed air complete all as directed by Engr-in-Charge. Note: (i)The rate unit quoted rates of this item shall be deemed to be inclusive of the cost of necessary spares required such as hinges, door locks, nuts, bolts, washers, kuchha rubbers etc. (ii) Necessary shut down of power supply shall be obtained by the contractor from the Engr-in-Charge prior commencing of work, also electric supply shall be restored as early as possible after completion of the work.

M & L for repair to foundation of LT panel including the mounting angle iron frame by lifting the LT panel and increasing the height of foundation / angle iron frame by at least to an height of one feet and not more than three feet in order to avoid water ingressing complete all as directed by Engr-in-Charge. Note: (i) The unit quoted rates shall be deemed to be inclusive of the cost of necessary excavation required to take out the cable loop, connecting and disconnecting the cables and necessary PCC required to increase the height of the foundation or any welding work required to increse the height of the mounting legs of the angle iron frame. However if any straight through joint or end termination joint if required will be measured and paid separately under relevant items. (ii) The contractor shall adhere to all safety measures required while lifting the LT Panel and any damage to man & material shall be at the risk of the contractor.

S & F in repair Indicator lamp, LED type of colour red, blue and yellow including taking down existing old/unserviceable lamps from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and asdtrected.

S&F in repair MCCB, 415 volts, 400 Amp, breaking capacity 36 KA, 4 pole including taking down existing old/unserviceable MCCB from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and as directed

S&F in repair MCCB, 415 volts, 250 Amp, breaking capacity 25 KA, 4 pole,including taking down existing old/unserviceable MCCB from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and as directed

S&F in repair MCCB, 415 volts, 200 Amp, breaking capacity 25 KA, 4 pole, including taking down existing old/unserviceable MCCB from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and as directed

S&F in repair MCCB, 415 volts, 160 Amp, breaking capacity 16 KA, 4 pole including taking down existing old/unserviceable MCCB from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and as directed

S&F in repair MCCB, 125 Amp, 415 volts, breaking capacity 16 KA, 4 pole, including taking down existing old/unserviceable MCCB from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and as directed

S&F in repair MCCB, 100 Amp, 415 volts, breaking capacity 10 KA, 4 pole, including taking down existing old/unserviceable MCCB from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and as directed

Supply & Fix in repair off load change over switch 4 pole of capacity 200 Amps in sheet steel enclosure rated voltage 415 V AC 50 Hz including connecting up the cables with suitable lugs complete all as specified and as directed Make INDOASIAN Cat part no OCFP0200 or euivalent in L&T, Havells, C & S etc.

S &F in repair 3/4 pole Contactor for capacitor switching suitable for 3 kVAr with 01 NO/NC aux contact AC 415/440 Volt ,50 Hz delatching type design of resistor switching block, low VA burden wide operating band coils with class 'H' insulation, high operating frequency and finger proof IP20 terminals complete all as specified and directed. Make :Havells Cat No IHPHE003110* or equivalent model in ABB, L&T, Schneider, C&S etc

S &F in repair 3/4 pole Contactor for capacitor switching suitable for 5 kVAr with 01 NO/NC aux contact AC 415/440 Volt ,50 Hz delatching type design of resistor switching block, low VA burden wide operating band coils with class 'H' insulation, high operating frequency and finger proof IP20 terminals complete all as specified and directed. Make :Havells Cat No IHPHE005110* or equivalent model in ABB, L&T, Schneider, C&S etc

S &F in repair 3/4 pole Contactor for capacitor switching suitable for 10 kVAr with 01 NO/NC aux contact AC 415/440 Volt ,50 Hz delatching type design of resistor switching block, low VA burden wide operating band coils with class 'H' insulation, high operating frequency and finger proof IP20 terminals complete all as specified and directed. Make :Havells Cat No IHPHE010110* or equivalent model in ABB, L&T, Schneider, C&S etc

S &F in repair 3/4 pole Contactor for capacitor switching suitable for 15 kVAr with 01 NO/NC aux contact AC 415/440 Volt ,50 Hz delatching type design of resistor switching block, low VA burden wide operating band coils with class 'H' insulation, high operating frequency and finger proof IP20 terminals complete all as specified and directed. Make :Havells Cat No IHPHE015110* or equivalent model in ABB, L&T, Schneider, C&S etc

S &F in repair 3/4 pole Contactor for capacitor switching suitable for 20 kVAr with 01 NO/NC aux contact AC 415/440 Volt ,50 Hz delatching type design of resistor switching block, low VA burden wide operating band coils with class 'H' insulation, high operating frequency and finger proof IP20 terminals complete all as specified and directed. Make :Havells Cat No IHPHE020210* or equivalent model in ABB, L&T, Schneider, C&S etc

Supply and fix in repair cylindrical capacitor heavy duty of capacity 1 kVAr,440 V , 50Hz, 3 phase complete including taking down old unserviceable capacitor from APFC panel all as specified and directed. Make: Havells Cat No QHHTCC5001X0 or equivalent model in ABB, L&T, Schneider, C&S etc

Supply and fix in repair cylindrical capacitor heavy duty of capacity 3 kVAr,440 V , 50Hz, 3 phase complete including taking down old unserviceable capacitor from APFC panel all as specified and directed. Make: Havells Cat No QHHTCC5003X0 or equivalent model in ABB, L&T, Schneider, C&S etc

Supply and fix in repair cylindrical capacitor heavy duty of capacity 5 kVAr,440 V , 50Hz, 3 phase complete including taking down old unserviceable capacitor from APFC panel all as specified and directed. Make: Havells Cat No QHHTCC5005X0 or equivalent model in ABB, L&T, Schneider, C&S etc

Supply and fix in repair cylindrical capacitor heavy duty of capacity 7.5 kVAr,440 V , 50Hz, 3 phase complete including taking down old unserviceable capacitor from APFC panel all as specified and directed. Make: Havells Cat No QHHTCC5007X5 or equivalent model in ABB, L&T, Schneider, C&S etc

Supply and fix in repair cylindrical capacitor heavy duty of capacity 10 kVAr,440 V , 50Hz, 3 phase complete including taking down old unserviceable capacitor from APFC panel all as specified and directed. Make: Havells Cat No QHHTCC5010X0 or equivalent model in ABB, L&T, Schneider, C&S etc

Supply and fix in repair cylindrical capacitor heavy duty of capacity 15 kVAr,440 V , 50Hz, 3 phase complete including taking down old unserviceable capacitor from APFC panel all as specified and directed. Make: Havells Cat No QHHTCC5015X0 or equivalent model in ABB, L&T, Schneider, C&S etc

Supply and fix in repair cylindrical capacitor heavy duty of capacity 20 kVAr,440 V , 50Hz, 3 phase complete including taking down old unserviceable capacitor from APFC panel all as specified and directed. Make: Havells Cat No QHHTCC5020X0 or equivalent model in ABB, L&T, Schneider, C&S etc

Supply and fix in repair cylindrical capacitor heavy duty of capacity 25 kVAr,440 V , 50Hz, 3 phase complete including taking down old unserviceable capacitor from APFC panel all as specified and directed. Make: Havells Cat No QHHTCC5025X0 or equivalent model in ABB, L&T, Schneider, C&S etc

Taking down the existing unserviceable CT from the LT panel / APFC panel and supply and fix in repair LT CT ring type suitable for primary current ratio 100/5 Amps, burden 5 VA, class 1.0 complete all as specified and directed. Make: Havells Cat Part No:QSCELFBOL001 or equivalent in ABB, Siemens, L&T, Schneider, C&S

Adinath Technical Services (BID ID -3483873)

SARATH ENTERPRISES (BID ID -3483633)

Rama Electricals (BID ID -3484112)

Mahindra Electric Stores (BID ID -3484236)

Pritam Electro Mechanical Services (BID ID -3483847)

TULAJA ENTERPRISES (BID ID -3484098)

SGS ENERGY (BID ID -3482822)

PROLINK COMPUTERS (BID ID -3481738)

REKHA ELECTRICALS (BID ID -3483510)

TRINSIYA ASSOCIATE (BID ID -3483391)

N B ENTERPRISES (BID ID -3482967)

R R Associates (BID ID -3482806)

JAWEED AHMED KHAN (BID ID -3484276)

ISHITARAJ ENTERPRISES (BID ID -3484195)

purva engineears and contracters (BID ID -3484006)

M S ELECTRICALS (BID ID -3482971)