SPECIAL REPAIR OF BLDG NO P-33, P-35 (JCOS LIVING) AND P-82 (COOK HOUSE) PORTION AT MIL STN KALKA UNDER GE (I) JUTOGH

Amount

Taking down cement plaster on brick or stone walls incl raking out joints hacking for key & scrubbing down with water etc., complete all as specified and directed.

M&L for 15mm thick cement plaster 1:6, on other than fair faces of brick work or concrete surafce finished fair and even without using extra cement, complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar 1:4, using water proofing compound, complete all as specified and directed. Note: WPC shall be measured and paid for separately.

M&L for 5mm thick cement plastering in CM 1:3 on fair faces of cocnrete ceiling surfaces finished even & smooth wihtout using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of OBD over 1-2mm (av-1.5mm) thick wall care putty to achieve smooth and even surfaces and complete all as specified and directed.

M&L for preparing new plastered ceiling surfaces and applying three coats of white wash, complete all as specified and directed

M&L for preparation of newly plastered wall surfaces and applying two coats of acrylic smooth exterior weather coat paint of required shade, new work applied @1.67ltr/10 sqm over and including priming coat of exterior primer applied @ 2.2kg/10Sqm), complete all as specified and directed.

M&L for complete removal of old plastered wall surfaces and applying two coats of Acrylic smooth exterior weather coat paint of required shade, New work applied @1.67ltr/10 Sqm over and including priming coat of exterior primer applied @ 2.2kg/10Sqm) complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of oil bound distemper on wall over primer a incl preparation of surface complete all as specified and directed.

M&L for preparation of old plastered surfaces and applying two coat of white wash on ceiling, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

M&L for PCC 1:2:4, type B-1, using 20mm graded mechanically crushed stone aggregates as in coping of pole and padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement, complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended item, complete all as specified and directed.

Dismantling timber scantlings framed/ unframed 40 sqcm and over in section, in any position complete all as specified and directed.

S&F second class hardwood as in scantlings timber fixed clean swan, complete all as specified and directed.

M&L for rolled sections Fe-410, Gde-E-250, quality -B, as in main and cross beams, hip and jack rafters; purlins where connected to common rafters, post and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, complete all as specified and directed.

Supply only Integral water proofing compound, complete all as specified and directed.

M&L for cleaning of roof slab surfaces including sweeping clean & washing down with water to remove dust & providing water proofing treatment with polymeric standard water proofing membrane, complete all as specified and directed. (a) M&L preparation of plaster surfaces /RCC roof surfaces and applying one coat of oil bound bituminous primer @0.03 ltr/Sqm (b) M&L applying blown type bitumen @1.20Kg/Sqm of grade 85/25 (c) Supplying and laying modified polymeric water proofing membrane super thermo lay 3mm thick of weight not less than 3.00kg /sqm reinforced with polyester non woven fabric weight not less than 150gm/sqm center core including coping on the surfaces with torch application of membrane with 10cm over laps as required. (d) Applying two coats of aluminium paint @ 0.2 kg/sqm.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and directed.

S&F GI frame work for ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 & 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section(not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.50mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre. size of grid 605mmx605mm incl Hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, complete all as specified and directed.

M&L for 4mm thick non asbestos fibre cement building boards white/ off white (E board designer) fixed or laid/ inserted to timber/ GI/ Aluminium frame work with screws in ceiling flat or sloping complete all as specified and directed.

Dismantling floor hearth and wall tiling incl cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for Non Skid ceramic colored tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in cement morat 1:6, complete all as specified and directed.

All as per Srl item No 24.00 above but on vertical surfaces such as skirting fixed on and including 10mm thick rendering in cement mortar 1:4 as backing coat, complete all as specified and directed.

M&L for coloured, glazed ceramic tiles in vertical surface 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and incl provn of 10 mm thick backing coat in CM 1:4, complete all as specified and directed.

Demolition of cement concrete (un-reinforced ) in ground floor and paving not exc. 15 cm thick (below and above ground level) complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in floor complete all as specified and directed.

M&L for machine cut Kota stone slab 18-20 mm thick, laid over and including 20mm thick screed bed in cement mortar (1:6) using coarse sand as in flooring, set & jointed in neat grey cement slurry and ponted in white cement mixed with pigment to match including grinding and polishing to granite finish complete all as specified and directed.

M&L for machine cut kota stone slab 18-20 mm thick, laid over and including 10mm thick rendering in cement mortar (1:4) using coarse sand as in vertical surfaces, set & jointed in neat grey cement slurry and ponted in white cement mixed with pigment to match including grinding and polishing to granite finish complete all as specified and directed.

M&L for joint filling of existing Kota stone slab flooring including rubbing and polishing etc complete all as specified and directed.

Taking down chowkhats or frames n.exc 1.5 sqm (without takingoff shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc., complete all as specified and directed.

Taking down chowkhats or frames Exc 1.5 sqm but n.exc 4 sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc., complete all as specified and directed.

S&F steel windows of profile rectangular tube section with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows of profile rectangular tube section with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with out glazing bars, dovetailed or welded complete all as specified and directed.

S&F steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; and similar work conforming to Fe-290 Gde-E-165, complete all as specified and directed.

S&F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane, complete all as specified and directed.

S&F pressed steel frames of size 125 x 60 mm for doors with one or more rebates including supply & fixing lugs, 125 mm size MS hinges, lock strike plate, etc., complete all as specified and directed.

S&F 35mm thick flush shutter, solid core construction with block board core and plywood face panels, both faces are covered with decorative face veneer with lipping/ frame to match, complete all as specified and directed.

S&F 35 mm thick factory made glazed & skelton shutter of second class hard wood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size of stiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2010), complete all as specified and directed.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: i) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. ii) For WPC solid door/ window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S & F for 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: Stainless steel butt hinges and necessary S S screws shall be paid separately.

M&L for preparation of new wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of syntheatic enammel paint over one coat of pink primer, complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any descirption not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint incl one coat of red oxide, complete all as specified and directed.

M&L for preparation for old or previosuly treated wooden surfaces of any description not otherwise described over 10cm width or grith and applying one coat of synthetic enamel paint to wooden surface complete all as specified and directed.

M&L for preparation of old steel surfaces of any descirption not otherwise described over 10cm width or grith and applying one coats of synthetic enamel paint complete all as specified and directed.

S&F stainless steel butt hinges medium weight, cold rolled, 100 mm, ISI marked, complete all as specified and directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and directed.

S&F 200 mm aluminium anodized, barrel tower bolts of extruded section, complete all as specified and directed.

S&F 100mm size aluminum handle fabricated, 'D' type, anodized ISI marked, complete all as specified and directed.

S&F 150mm size aluminum handle fabricated, 'D' type, anodized ISI marked complete all as specified and directed.

S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplesor MS beads size 2mm to 3mm, complete all as specified and directed.

M&L for PCC 1:3:6, type C-1, using 20mm graded mechanically crushed stone aggregate as in filling pressed steel frame/ hold fast blocks etc., complete all as specified and directed.

S&F 300mm MS ordinary rat tail rod pattern springs incl roller and roller plate fixed to wooden chowkhats or welded to angle iron door frames, complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar incl all quoins, pillars, arches etc but excluding ashlar facing, complete all as specified and directed

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6), complete all as specified and directed..

M&L for 75mm thick, PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in plinth protection, complete all as specified and directed.

S&F vitreous china wash down water closet (pedestal pattern), white (excluding fixing bolts flushing cistern and flush pipe), fixed in repairs, including connection to wate pipe, flushing pipe, anti-syphonage pipe etc. and making good to floor complete all as specified and directed.

S&F in repair plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging devices, connected to drains outlet, complete all as specified and directed.

S&F in repair 10 litres capacity, PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and suitable flush pipe PVC 32mm dia complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair angle cock/ stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15 mm bore iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair stop valves, cast copper alloy, chromium plated, fancy type, with long shank and cup (concealed type), screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15mm bore iron pipe or for unions complete all as specified and directed.

S&F vitreous china wash hand basin, white, flat Back of size 550 mm x 400 mm including bracket grouted in cement Morter 1:2 in wall,32 mm dia CP Brass waste coupling and 600 mm longe HDPE waste down pipe including complete all as specified and directed.

S&F in repair bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair chromium plated brass shower rose 125 mm sizewith or witout swivel joints including fxing with 15 mm bore pipe, complete all as specified and directed.

Dismantling OH water tank of capacity exc 250 ltr but not exceeding 500 ltr and removing from site, complete all as specified and directed.

S&F for triple layer white color 500 Ltrs rotational moulded polyethylene (PVC) water storage tanks cylindrical vertical with closed top including nipple nuts and washers for fixing inlet, outlet/washout pipes and air vent pipes, complete all as specified and directed.

S&F in repair, PVC (SWR) floor trap, 75mm bore, plain with grating including jointing with solvent cement, complete all as specified and directed.

S&F in repair CP brass soap dish, complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

S&F PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe 32mm bore suitable for wash hand basins/ sinks, complete all as specified and directed.

S&F grating doom 100mm dia of PTMT (Minimum weight 25gms), complete all as specified and directed.

Taking up or down steel tubing and connection 15 mm bore pipe and removing from site, complete all as specified and directed.

All as per Srl Item No. 77.00 above but for 20 mm bore pipe, complete all as specified and directed.

S&F 15mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F 20mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F brass chromium plated health faucet with 1 meter long flexible hose and wall hook complete all as specified and directed. Make: Jaquar/ Parko/ Gem or equivalent as approved.

S&F in repair stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl fixing of brackets,Knob fancy type fixed with stainless steel screws etc complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated guard and railing 60 cm long, complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges and complete all as specified and directed

S&F in repair stainless steel grating 100mm dia with waste pipe hole fixed to floor trap, complete all as specified and directed.

S&F 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) complete all as specified and directed.

S&F gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore, complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including stack clamp complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laying as in floor and complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laying as in floor, complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal provided with access door, complete all as specified and directed.

S&F 75mm bore, PVC (SWR) junction single, (Single T) equal or unequal provided with access door, complete all as specified and directed.

S&F PVC (SWR) bends 110mm bore any radius, complete all as specified and directed

S&F PVC (SWR) bends 75mm bore any radius, complete all as specified and directed

S&F PVC (SWR) vent cowl 110 mm bore any radius, complete all as specified and directed

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft and loose soil, complete all as specified and directed.

M&L for hard core, using broken stone boulders to gauge n exc 63 mm, complete all as specified and directed

M&L for 75mm thick PCC, 1:4:8, type D-2, using 40mm graded crushed stone aggregate as in sub base, complete all as specified and directed.

M&L for chequered cement concrete tiles pre polished 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment in floors incl 15mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed.

M&L for continuous brick edging with width equal to the depth of the brick, laid dry, on edge with burn and clay brick of sub class B old size, complete all as specified and directed.

Excavation in trenches n. exc. 1.50m wide and n. exc. 1.50m depth for foundation, etc or for manholes/ sewage lines etc., n.exc 10 sqm on plain and getting out in hard/ dense soil, complete all as specified and directed.

M&L for PCC 1:4:8, nominal mix using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/ dense soil, complete all as specified and directed.

Removing excavated material n exc.50m and deposited where directed at a level n exc 1.5 m above the starting point in soils, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4, type B-1, smooth finished nad reforming benching as required, complete all as specified and directed.

M&L for 150mm dia reinforced concrete pipes, Class NP-3, laid and jointed complete with collars, complete all as specified and directed.

M&L for concrete bed to drain pipes of 150mm dia including packing under, and hauncing against the sides of pipes after they are laid and tested in cement concrete 1:3:6, type C-2, complete all as specified and directed.

M&L for PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in cover slabs placed in position over manholes etc including use and waste of necessary formwork complete all as specified and directed. Note:- Reinforcement and handles shall be measured and paid separately.

M&L for TMT bars 6 to 8mm dia and over cut to length bent to shape required and binding with ms wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for PCC 1:2:4, type B-0, using 12.5mm graded mechanical crushed stone aggregate for benching, coping shall be 150mm in radius mixed with acrylic based polymner water proofing compound, complete all as specified and directed. Note: WPC shall be measured and paid separately.

M&L for PCC 1:3:6, type C-1, 20mm graded crushed stone aggregate as in MH PCC incl fair finished drain or channel using extra cement including forms, moulds, mitred/ stopped ends etc., complete all as specified and directed.

S&F PVC (SWR) gully trap 125/ 110, setting and jointing with solvent cement complete all as specified and directed

Taking down chowkaths or frames exc 1.5 sqm n. exc 4 sqm (without takingoff shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc., complete all as specified and directed.

M&L for old size brick work with sub class 'B' briick straight or curved on plan to any radius in half brick thick built in CM 1:4 complete all as specified and directed

M&L for coloured glazed ceramic tiles in vertical surfaces 350x250x7mm/ 450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick backing coat in CM 1:4, complete all as specified and directed.

M&L for mirror polishing on kota stone whereever required to give high gloss finish incl filling of joints with pigments to match complete all as specified and directed.

M&L for mild steel bars 10mm dia TMT bar and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L for mild steel bars 5mm and over upto and including 10mm dia in stirrups spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L for for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., complete all as specified and directed.

M&L for RCC 1:1.5:3, type A-1, using 20mm graded mechanically crushed stone aggregate as in chajjas/ lintel/beam etc., complete all as specified and directed.

M&L for RCC 1:1.5:3, type A-1, using 20mm graded mechanically crushed stone aggregate as in shelves etc., complete all as specified and directed.

S&F pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for doors with double rebate including one shop coat and necessary fixing hold fast, lugs, hinges, lock strike plate, etc., complete all as specified and directed.

S&F pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for doors with single rebate includingone shop coat and necessary fixing, hold fast, lugs, hinges ,lock strike plate, etc., complete all as specified and directed.

S&F 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both rail and stile as per IS:1003 faces. The size of (Part I), kiln seasoned and chemically pressure treated, supplied and fitted to chowkats complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows & other frames/ chowkhat of size 50 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: i) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made, for cupboards.

S&F door magnet/ door catcher for cabinet cupboard / ward droobe, kitchen including sutable screws for fixings, complete all as specified and directed

S&F 125mm size, aluminium (cast type) anodized, handle and fixed with screws complete all as specified.

S&F in repair floor door stopper aluminium body and tongue, anodised overall length of cover plate of size 140 mm long with hard drawn steel spring. complete all as specified and directed .

S&F 18-20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like over and including 15mm screed bedding in CM 1:4, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed

Rounding to edges of stone (of any description) slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

S&F 18 mm thick with min density 600 Kg/cum LEAD FREE PVC Celuka ply of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed.

S&F 18 mm thick with min density 600 Kg/cum LEAD FREE PVC Celuka ply of single side rigid laminate of approved colour and other side plain white colour fixed with SS screws and solvent cement/ adhesive to make kitchen cabinet shutters and shelves complete as per manufacturer’s specifications complete all as specified and directed.

S&F 12 mm thick with min density 600 Kg/cum LEAD FREE PVC Celuka ply fixed with SS screws and solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per manufacturer’s specifications complete all as specified and directed.

S&F auto closing hinges 35 mm of crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position, complete all as specified and directed.

S&F D-type cabinet handles premium quality, stainless steel 304/ gloss chrome/ SN finished 150mm long matt finished complete fixed in position complete all as specified and directed.

S&F in repair 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles scrwed down suitable for 15mm bore pipe or union complete all as specified and directed.

M&L for preparing new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparing new plastered surfaces of walls with two coats cement base paint on wallls over a coat of alkali resistant paint, complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of cement base paint on wall incl preparation of surfaces and coat of primer with alkali- resistant priming paint, complete all as specified and directed.

S&F 75mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

Taking down carefully existig copper/ alumn point wiring for light/ fan/ bell/ socket 5/15 Amp points complete with fitting and fixtures such as switches, sockets, ceiling rosess, holders and bracket fittings with battens/ conduits/ wires, tube light fittings and making good the disturbed surfaces of walls and roofs etc.and to match with existing colour complete all as specified and directed.

Taking down carefully unserviceable main switches and distribution boards with fuses/ MCB's (single phase or three phase) of any capacity complete all as specified and directed.

Taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as specified and directed.

M&L for point wiring complete with 1100 volts grade PVC FRLS-H insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through & including PVC rigid concealed conduit, medium grade of suitable size (not less than 20mm dia) duly ISI marked with all accessories such as bends, reducers, spacers, saddles, junction boxes, bakelite sheets, sizes for mounting switch/ sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS-H copper conductor, insulated, unsheathed, stranded (Green colour) connected to common earth dolly, One light/fan/bell/Bldg security light point controlled by one single pole one way switch, complete all as specified and directed.

All as per Srl item No 145.00 above but for one 3 pin 5 Amp socket outlet point controlled by one switch on Independent board, complete all as specified and directed.

All as per Srl item No 145.00 above but for one 3 pin 5 Amp socket outlet point controlled by one switch on same board, complete all as specified and directed.

All as per Srl item No 145.00 above but for one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 2.5 Sqmm PVC insulated,stranded,unsheated copper conductor on independednt board with continuous earth wire of size 2.5 Sqmm green colours PVC insulated, unsheathed, stranded copper conductor cable, complete all as specified and directed.

S&F 6 amps, single pole, one way switch urea back piece (IP20), 240V, 50Hz, white in colour, duly ISI marked, complete all as specified and directed.

S&F switch piano flush type 20 amps, single pole one way, white in colour, duly ISI marked complete all as specified and directed.

S&F 6 Amps Socket 2 in 1, Urea backpiece (IP20), white in colour, duly ISI marked complete all as specified and directed.

S&F Socket outlet, UNI, 2 in one 10 Amps & 20 Amps, white in colour, duly ISI marked complete all as specified and directed.

S&F ceiling rose surface type, 240 volts, 50 Hz, 6Amp, Pilot 3 plate, white in colour, bakelite 65 x 50mm, 3 terminals duly ISI marked complete all as specified and directed.

S&F batten holder, 240 volts, 50 Hz, 6Amp, white in colour, duly ISI marked complete all as specified and directed.

S&F rotary stepped type electronic fan regulator for ceiling fan 1200/1400mm size, 240 volts, 6 Amps, 100W, deluxe, white in colour, compatible for BLDC Fans duly ISI marked with fan hook if reqd complete all as specified.

S&F LED light fitting 1 x 20 Watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F LED bulb of 9/ 10 watts, B-22 CDL, 3 star, 6500K, complete all as specified and directed.

S&F factory made three phase and neutral sheet steel made out of CRCA 1.2 mm thick, powder coated double door vertical DB 4way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail suitable for use on 240/ 415V, 50Hz supply, VTPN DB, partly immersed in wall, including of MCCB 4 pole adjustable thermal & fixed magnetic type 63 Amps, 50Hz, 415 Volts with rupturing capacity 16 KA and making good distrubbed surfaces with matching colour, complete all as specified and directed.

S&F factory made single phase and neutral sheet steel made out of CRCA 1.2mm thick, powder coated double door vertical DB 8way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 240V, 50Hz supply, partly immersed in wall and making good distrubbed surfaces with matching colour, complete all as specified and directed.

S&F MCB SPN, 40 - 63Amps, 240 volts, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning, complete all as specified and directed.

S&F MCB SP, 6-32 Amps, 240 volts, 10KA duly ISI marked, in the MCB DB, complete with connection testing and commissioning, complete all as specified and directed.

M&L for Sub main wiring with two single core 2x6 sqmm FRLS insulated and unsheathed stranded copper conductor alongwith earth wire 6.0 sqmm drawn in FRLS-H rigid conduit connected to main board complete all as specified and directed. NOte: Two runs cable and one number earth wire and suitable FRLS-H conduit shall measured together as unit length.

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/ 66 protection, complete all as specified and directed.

M&L for earthing complete with galvanized steel plate elecrode of size 60cmx60cmx6.3 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shallbe provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC 1:3:6, type C-2, using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete 1:2:4, type B-1, using 20 mm graded stone aggregate and MS angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to sxposed steel surfaces. excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009), complete all as specified and directed.

Supply, laying, jointing and testing of cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured heavy duty electric cable with multistranded aluminium conductor, 1100 volts grade of size 25 Sqmm, 4 core, confirming to IS:7098 (Part-1) laid in trenches, under road or passing through pipes/ ducts or fixed to walls/ poles complete with proper thimbles complete all as specified and directed.

S&F in repair busbar chamber TPN - Type (Busbar made of ETP Grade Copper) in sheet metal enclosure having 200A TPN BBC (Cu.) with 4 out going ways & IP-42 Protection complete all as specified and directed.

Excavation in trenches in soft/loose soil n.exc 1.5 mtr deep and n.exc 1.5 mtr wide for laying of HT cable and getting out including dressing/ trimming of sides and leveling, grading and ramming of bottom of excavation complete all as specified and directed.

M&L for sub class 'B' old size of Brick in trenches for cable protection of LT Cables, complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation for UG cable, complete all as specified and directed.

S&F in repair for GI pipe light grade of size 40mm dia laying in trenches/ under floor/ on walls for protection of UG cables, complete all as specified and directed.

S&F factory made three phase and neutral sheet steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 4 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail suitable for use on 240/415V, 50Hz supply, VTPN DB, partly immersed in wall, including of MCCB 4 pole adjustable thermal & fixed magnetic type 100 Amps, 50Hz, 415 Volts with rupturing capacity 16 KA and making good distrubbed surfaces with matching colour, complete all as specified.

S&F MCB TPN, 40-100Amps, 240 volts, C - series, 10 KA duly ISI marked, complete all as specified and directed.

S&F exhaust fan heavy duty steel body with louvers complete of sweep size 450 mm, single phase with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection, complete all as specified and directed.

S&F exhaust fan heavy duty steel body with louvers complete of sweep size 300 mm, single phase with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection, complete all as specified and directed.

Cutting holes making good the distributed surface, grouting nuts for fixing of Exhaust fans complete all as specified and directed.

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc., complete all as specified and directed.

S&F in replacement Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB of C-series complete all as specified and directed.

S&F galvanised iron steel tubing medium grade of size 15mm complete with all fittings such as bend, tee, reducer, elbow and union of require size including fastners, bolts, washers. and making good the disturbed surfaces to match with the existing surface complete all as specified and directed.

S&F in repair on load change over switch, 4 pole, 100 Amps capacity with center handle in sheet steel enclosure complete all as specified and directed. Make: Havells/ L&T/ Siemens or equivalent as approved.

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc as required 4mm dia galvanised iron or steel wire, complete all as specified and directed.

Supply, fixing or laying of HDPE (DWC) tubing 40mm inner dia of pressure rating 6Kgf/Cm2 and as per IS:16205 fixing on poles, walls under floors, laying on surface etc., complete all as specified and directed.

Supply, laying, jointing and testing of cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured heavy duty electric cable with multistranded aluminium conductor, 1100 volts grade, laid in trenches or duct or passing through pipe or fixed to poles walls of size 10 Sqmm 2 core confirming to IS: 7098 (Part-I) laid in trenches, under road or passing through pipes/ ducts or fixed to walls/ poles complete with proper thimbles complete all as specified and directed.

S.R.SHARMA & SONS (BID ID -3493797)