Repair to RB33 diesel engine and repairs to 3 cusec pump along with allied works of drought lift irrigation station Sai. Annual periodical maintenance and repairs to RB 44 diesel engine and repairs to 5 cusec pump along with allied works of drought l

Repair to RB33 diesel engine and repairs to 3 cusec pump along with allied works of drought lift irrigation station Sai.

Repair to three cylinder RB 33 diesel engine by way of dismantling it from suction, delivery pipes and decoupling the pump from engine. Shifting of pump and engine to workshop from site of installation for repair by head load, crane to road side and carriage vehicle. Complete dismantling to three cylinder RB33 engine at workshop. Extraction of damaged parts i.e. crankshaft, piston with rings, head, valves etc. Providing and fitting of new pistons with rings 3 no’s, cylinder liner 3 no’s, guide 6 no’s, inlet and exhaust valves, piston pins, new main and big end bearings 3 no’s, CR bushes 3 no’s, push rods 6 no’s, gasket sets, Providing and fitting of M/oil filter and diesel filter, repairs to exhaust manifold by properly cleaning all carbon deposits, providing and fitting of air filter assembly, fuel pipes sets with banjo bolt, thrust washers, hoses set. Repairs to cylinder head by way of turning on lathe machine and finishing to required size. Cleaning of oil sump to remove all deposits. Repair to crank shaft by way of grinding and finishing to required precision size. Adjustment of the rocker and tappet assembly. Providing, fitting and replacement of new radiator assembly with upper and lower tank. Providing and filling of M.Oil of 15W40 grade and coolant in the engine and radiator up to required level. Repairs and calibration of Fuel Injection Pump by completely dismantling of all parts and providing and fitting of injector nozzles 3 no’s, D valves 3 no’s, element 3no’s, plungers, springs, lock nuts, nuts and bolts. Providing and fitting of governing set, seals, washers, diaphragm washers, calibration of pump on calibration bench. Fitting fuel injection pump with engine and testing of engine no load and full load. Providing and fitting self (starter motor) compatible with RB 33 engine and providing and fitting of 12 volt,150 ampare battery and compatible with starter and RB33 engine of standard ISI mark and minimum of 18 months warranty. Repairs to 3 cusec pump by way of dismantling spiral casing pump at workshop by completely draining of old oil from the bearing housing and extraction of all worn out/damaged parts, i.e. pump shaft, impeller, bearings, sleeve, bush, check nut, nuts & bolts, gland plate, gland studs. Providing, fitting and replacement of pump shaft and turning, finishing to original size with outer threading as per the size of check nuts. Repairs to impeller by metal filling, grinding and finishing to original size. Providing and fitting of two number new bearings, neck ring, shaft protection sleeve, check nut, nuts & bolts, fabrication of new gland plate with providing and fitting of 2 no’s new gland studs. Completely cleaning of bearing housing to remove dust and metal residue. Reassembling all parts of pump with proper greasing & filling of pump bearing housing with fresh enclo 60-70 grade M-oil up to the required level. Assembling of pump with engine and connecting with suction and delivery pipes. Providing of new nuts and bolts with rubber gaskets. Providing and fitting of graphite packing. Repairs to coupling pulley by providing, fitting and replacement of coupling bolts along with rubber bushes. Repair to 150 mm diameter foot valve of pump by way of dismantling all moving and fixed parts. Cleaning of all internal parts to remove silt and rust. Fabrication of new foot valve plate as per size, new leather washer, hinge pin, new nuts & bolts. Complete painting of pump and engine with enamel paint after scrubbing of old paints and rusts. Carriage charges to nearest road side point at Sai. Shifting from road side to site of installation on head load, manual labour, tools and tackles. Job includes cost of labour, materials, loading and unloading charges, hire charges of crane, tools and tackles, mechanical transport (to and fro) and installation and testing charges. Complete Job.

Rebate on Old Parts

Annual periodical maintenance and repairs to RB 44 diesel engine and repairs to 5 cusec pump along with allied works of drought lift irrigation station Harapeer.

Annual periodical maintenance/ repair to four cylinder RB 44 diesel engine installed at Drought lift station, Harapeer by way of dismantling it from suction, delivery pipes and decoupling the pump from engine. Shifting of damaged parts of engine and pump to workshop for repairs. Repairs and calibration of Fuel Injection Pump by completely dismantling of all parts and providing and fitting of injector nozzles 4 no’s, D valves 4 no’s, element 4 no’s, plungers, springs, lock nuts, nuts and bolts. Providing and fitting of governing set, seals, washers, diaphragm washers, calibration of pump on calibration bench. Fitting fuel injection pump with engine and testing of engine no load and full load. Repairs to cylinder head by way of turning on lathe machine and finishing to required size. Cleaning of oil sump to remove all deposits. Providing and fitting of fuel intake and M oil pipes. Providing and fitting of air filter, diesel filter and M oil filter. Filling of 15W40 grade M.Oil and coolant in the engine and radiator upto required level. Repair to radiator assembly by way of dismantling the upper and lower tank, then cleaning the tubes and tanks with cleaning chemicals. Repair to radiator by brazing and testing of radiator for any leakages. Providing and fitting of 20 ltr oil tank for engine, the tank must be leak proof with sufficient inlet of diesel and have standard outlet for connecting diesel pipe to engine. Providing and fitting of diesel pipe from oil tank to engine. Repairs to 5 cusec pump by way of dismantling spiral casing pump at workshop by completely draining of old oil from the bearing housing and extraction of all worn out/damaged parts, i.e. pump shaft, impeller, bearings, sleeve, bush, check nut, nuts & bolts, gland plate, gland studs. Providing and fitting of new pump shaft, turning and finishing to original size with outer threading as per the size of check nuts. Repair to impeller by metal filling of cracked positions and finishing to original size. Providing and fitting of two number new bearings, neck ring, shaft protection sleeve, check nut, nuts & bolts, fabrication of new gland plate with providing and fitting of 2 no’s new gland studs. Completely cleaning of bearing housing to remove dust and metal residue. Reassembling all parts of pump with proper greasing & filling of pump bearing housing with fresh M-oil upto the required level. Assembling of pump with engine and connecting with suction and delivery pipes. Providing of new nuts and bolts with rubber gaskets. Providing and fitting of graphite packing. Carriage charges to nearest road side point at Harapeer. Shifting from road side to site of installation using crane, manual labour, tools and tackles. Job includes cost of labour, materials, loading and unloading charges, hire charges of crane, tools and tackles, mechanical transport (to and fro) and installation and testing charges. Complete Job.

Rebate on Old Parts

N B Engineering and Electric Works

Rishabh Electricals and Mechanical Works

M/S FASTTRACK ENGINEERS

CHENAB ENGINEERING WORKS

Rishabh Electricals and Mechanical Works